1

Hardware
Description
 2
Power Box

3 4 6 9 10 11

20A 20 A 20A 2A 20A 2 0A 20 A 2A

RTN (+) NEG(-) R TN(+) N EG(- )

OUT1 OUT2 OUT3 AUX OUT1 OUT2 OUT3 AUX

ON ON ON ON ON ON

OFF O FF O FF O FF OFF O FF ALARM SERIAL

RUN RUN TEST RUN

PO W ER IN SW 1 SW 2 SW 3 POW ER IN SW 1 SW 2 SW 3 MU T E AL M
AL M AL M
PMU
PDU PDU

1 2 5 7 8 12
1 PDU board 7 TEST switch
2 RUN and ALM indicators on PDU 8 MUTE switch
3 Protection grounding screws 9 ALARM interface
4 Input cable terminals 10 SERIAL interface
5 Three power distribution switches 11 PMU
6 Output cable terminal 12 RUN and ALM indicators on PMU
 3
Power Box

 A PMU board is the main part of a power box. The board has the following functions:
 Monitoring voltage
A PMU monitors the input voltage of two –48 V/–60 V power. The PMU also reports the voltage value and voltage
alarms. The alarms include over- and under-voltage alarms. For the alarming threshold, you may take the default value in
the system, or set a value according to your requirement. In different applications, the voltage alarming thresholds can be
set as:
Over-voltage threshold: –60 V ± 1 V for nominal –48 V DC, or –71 V ± 1 V for nominal –60 V DC.
Under-voltage threshold: –41 ± 1 V for nominal –48 V DC, or –51 V ± 1V for nominal –60 V DC.
The board monitors the input voltage of eight branch powers. When a branch power fails (for example, the
corresponding branch power is not accessed or the power is switched off manually), the power status alarm of this
branch power is reported. When a power supply fails (for example, the second power supply is not accessed), the under
or over-voltage alarm of this power supply is reported and the corresponding four branch powers of this power supply
report the power status alarm at the same time.
 4
Power Box

 Monitoring temperature
A temperature sensor in the power box monitors the temperature. Note that the sensor measures
the ambient temperature inside the power box, not that of the subracks or boards.
 Monitoring alarms
One PMU can monitor 16 external alarm inputs and four equipment alarms. The PMU outputs the
alarms occurred and supervises the external environment.
 5
Power Box

 DIP Switches (PMU)

The third bit of the DIP switch: not covered by WDM equipment
The fourth bit of the DIP switch provides an option for monitoring
the voltage of the power supply . When the fourth bit of the DIP
is set to OFF, the working voltage is –48 V DC. when it is set to ON,
the working voltage is –60 V DC. The default state is OFF.
 6
Power Box

 Interface Description: Serial

A SERIAL is a communication interface
between the PMU and the subrack in the
cabinet. The SERIAL is also an interface for
driving signal of the cabinet indicator.
When the SCC board gives out a critical
alarm signal, the red indicator flashes and
the buzzer buzzes. The MUTE switch at the
cabinet top or the ALC switch of the SCC
board controls the buzz sound.
 7
Power Box

 Interface Description: Alarm

The transmission equipment outputs the alarm signal
of the cabinet to the centralized alarming system .
The power box provides four alarm outputs, one for
major alarm, one for critical alarm, and the other
two for auxiliary Boolean value. If the centralized
alarming system is in audio alarm mode, the alarm
mute function is required . The power box
provides 16 input interfaces for external alarms.
W2 and W3 are alarm output/cascade cables, W1 is the alarm input cable. The
alarm signals are cascaded among cabinets through W2 and W3. The last cabinet transmits the
signals to the centralized alarming system.
 8
Communication and Maintenance
Interfaces
 9
Communication and Maintenance
Interfaces
 ETHERNET1
Serves as the Telecom management network (TMN) interface and local NE management interface. It
connects to the ETHERNET2 interface on another subrack through cross-over network cables, to achieve
theinter-subrack communication concatenation.
 ETHERNET2
Serves as the communication interface with the ROP board in the remote optical pumping amplifier
(ROPA) system.
When the WMU is configured for centralized wavelength monitoring, ETHERNET2 can be used as a
backup network interface for inter-subrack communication.
It connects to the ETHERNET1 interface on another subrack through cross-over network cables, to
achieve the inter-subrack communication concatenation.
 10
Communication and Maintenance
Interfaces
PHONE1/PHONE2/PHONE3
Serves as the orderwire phone interface that uses the optical supervisory channel (OSC) and electrical
supervisory channel (ESC). Provides a 64 kbit/s orderwire voice channel for direct orderwire
communication between terminals.
F&f
Possesses all the features of RS-232 interface. Serves onlyas an interface for software internal testing.
Serial 1
Uses the F2 byte of the supervisory channel and possesses the features of both RS-232 and RS-422
interfaces. The maximum rate is 19.2 kbit/s.
 11
Communication and Maintenance
Interfaces
Serial 2
Uses the F3 byte of the supervisory channel and possesses the features of both RS-232 and RS-422
interfaces. The maximum rate is 19.2 kbit/s.
ALM
Serves for subrack alarm output. The ALM communicates with the PMU board located in the power box.
The ALMis connected with the subrack communication interface(SERIAL) on the power box panel.
OAM
Serves as a local NE management interface. Operation , administration and maintenance interface.
F1
Serves as a 64 kbit/s co-directional data interface.
 12
DCM

 The system provides various DCMs for C band.

 The system provides two types of DCM:
the DCM based on dispersion compensation fiber (DCF) and the DCM based on Fiber Bragg Grating (FBG). The DCF-
based DCM and the FBG-based DCM have similar compensation features. The differences are as follows:
The insertion loss of the DCF-based DCM increases with the distance in km.
The insertion loss of the FBG-based DCM is always 4 dB regardless of the distance in km.
 13
Laser Safety Labels Overview
 14
Bar Codes For Boards
 15
LWFS
 The LWFS is a type of optical transponder unit. The LWFS realizes the conversion between STM-64/OC-
192/10GE-WAN optical signals and ITU-T Recommendation-compliant WDM signals.
 16
LWFS
 Client-side optical module:
The module consists of two parts: the client-side receiver and the client-side transmitter. Client-side receiver: Performs O/E conversion of
standard STM-64, OC-192 or 10GEWAN optical signals. Client-side transmitter: Performs E/O conversion from the internal electrical signals
to standard STM-64, OC-192 or 10GE-WAN optical signals.
Reports the working state of the client-side laser.
 WDM-side optical module
The module consists of two parts: the WDM-side receiver and the WDM-side transmitter.
WDM-side receiver: Performs O/E conversion of standard OTN optical signals at 10.71 Gbit/s or 11.1 Gbit/s, and extracts clock from the
electrical signals.
WDM-side transmitter: Performs E/O conversion from the internal electrical signals to
standard OTN optical signals at 10.71 Gbit/s or 11.1 Gbit/s, and multiplexes the clock
signals with the electrical services signals.
Reports the performance of the WDM-side optical interface.
Reports the working state of the WDM-side laser.
 17
LWFS
 Service en/de-capsulation and processing module
The module consists of the SDH/SONET en/de-capsulation module and the service processing module. It realizes the en/de-
capsulation of signals in different types.
SDH/SONET en/de-capsulation module: Realizes the mapping of SDH/SONET and 10GE-WAN signals, and reports the
performance monitoring state of service signals.
Service processing module: Performs processes such as encapsulation/decapsulation of FEC, encoding/decoding and
scrambling/descrambling.
The module encapsulates signals into OTU2 frames.
 Control and communication module
Controls the operations on the board.
Controls the operations on each module of the unit according to CPU instructions.
 Power supply module
Converts the -48 V/-60 V DC power into the power required by each module of the board.
 18
LWFS
 19
LWFS
 20
LWFS
 21
LWFS
 22
LWFS

 LWFS Board Specifications(client side)

 23
LWFS

 LWFS Board Specifications(client side)

 24
LWFS

 LWFS Board Specifications(WDM side)

 25
LWFS

 LWFS Board Specifications(WDM side_Fixed wavelength)

 26
LWFS

 LWFS Board Specifications(WDM side_Tunable wavelength)

 27
LWFS

 LWFS Board Specifications(WDM side_Tunable wavelength)

 28
D40
 The D40 is a type of optical demultiplexer unit. The D40 realizes the demultiplexing of one optical signal into a
maximum of 40 ITU-T Recommendation-compliant WDM signals.
 29
D40
 Optical module

Demultiplexes the one channel of multiplexed optical signals into 40 channels of single

wavelength optical signals.

The optical splitter splits some optical signals from the main optical path for input

optical power detection.

The optical splitter splits some optical signals from the main optical path and provides them to

the MON interface for detection.

 30
D40
 Detection and temperature control module
Monitors and controls in real time the demultiplexer operating temperature.
Detects in real time the input optical power of service signals.
 Control and communication module
Controls the operations on the board.
Collects the information of alarms, performance events, and working states of each functional
module of the unit.
Communicates with the SCC board.
 Power supply module Converts the -48 V/-60 V DC power into the power required by each
module of the board.
 31
D40
 Optical Specifications
 32
FIU
 The FIU is a type of optical multiplexer and demultiplexer unit. The FIU realizes the multiplexing and
demultiplexing of the signals transmitted by the main optical path and the optical supervisorychannel.
 33
FIU
 Optical module
Performs the multiplexing and demultiplexing of main path signals and supervisorychannel signals.
The optical splitter splits some optical signals from the line optical signals and provides them to the MON interface for
detection.
 Optical power detection module
Detects in real time the input and output optical power of service signals.
 Control and communication module
Controls the operations on the board.
Collects the information of alarms, performance events, and working states of each functional module of the unit.
Communicates with the SCC board
 Power supply module
Converts the -48 V/-60 V DC power into the power required by each module of the board.
 34
FIU
 Optical Specifications
 35
ITL
 The ITL is used to multiplex or demultiplex the odd channels and even channels. The cooperation of the ITL01, ITL02
and ITL03 can realize the transmission of 192 channels in C-band.
 36
ITL

 Optical module
 ITL01/ITL05: Performs the transformation between C-band optical signals in 100 GHz spacing and C-
band optical signals in 50 GHz spacing.
 Control and communication module
Controls the operations on the board.
Collects the information of alarms, performance events, and working states of each functional module of
the unit.
Communicates with the SCC board.
 Power supply module
Converts the -48 V/-60 V DC power into the power required by each module of the board.
 37
ITL
 Optical Specifications
 38
M40
 The M40 is a type of optical multiplexer unit. The M40 realizes the multiplexing of a maximum of 40 ITU-T
Recommendation-compliant WDM signals into one main path.
 39
M40
 Optical module

Multiplexes the 40 channels of single-wavelength optical signals into one channel of multiplexed
optical signals.

The optical splitter splits some optical signals from the main optical path for output optical power
detection.

The optical splitter splits some optical signals from the main optical path and provides them to the
MON interface for detection.
 40
M40
 Detection and temperature control module
Monitors and controls in real time the multiplexer operating temperature.
Detects in real time the output optical power of service signals.
 Control and communication module
Controls the operations on the board.
Collects the information of alarms, performance events, and working states of each functional
module of the unit.
Communicates with the SCC board.
 Power supply module
Converts the -48 V/-60 V DC power into the power required by each module of the board.
 41
M40
 Functions and Features
 42
M40
 Optical Specifications
 43
V40
 The V40 is a type of optical multiplexer unit with VOA. The V40 realizes the multiplexing of a maximum of 40 ITU-
T Recommendation-compliant WDM signals into one fiber and adjusts the output optical power of each wavelength
signal.
 44
V40

 Optical module
Performs the optical power adjustment to the single-wavelength optical signals before
multiplexing.
Multiplexes the 40 channels of single-wavelength optical signals into one channel of multiplexed
optical signals.
The optical splitter splits some optical signals from the main optical path for output optical power
detection.
The optical splitter splits some optical signals from the main optical path and provides them to the
MON interface for detection.
 45
V40

 Detection and temperature control module

Monitors and controls in real time the multiplexer operating temperature.
Detects in real time the output optical power of service signals.
 Control and communication module
Controls the operations on the board. Collects the information of alarms, performance events, and
working states of each functional module of the unit. Communicates with the SCC board.
 Power supply module
Converts the -48 V/-60 V DC power into the power required by each module of the board.
 46
V40
 Functions and Features
 47
V40
 Optical Specifications
 48
VA4
 The VA4 is a type of variable
optical attenuator unit. The VA4
realizes the power adjustment
for 4 optical signals.
 49
VA4
 Variable optical attenuator
Adjusts the optical power of the input optical signals.
 Driving and control module
Drives and controls the variable optical attenuator, and reports the detected attenuation to the control and communication
module.
 Control and communication module
Controls the operations on the board.
Controls the operations on each module of the unit according to CPU instructions.
Collects the information of alarms, performance events, working states and voltage detection of each functional module of
the unit. Communicates with the SCC board.
 lPower supply module
Converts the -48 V/-60 V DC power into the power required by each module of the board.
 50
VA4
 Functions and Features
 51
VOA
 The VOA is a type of variable optical attenuator unit. The VOA realizes the power adjustment for one optical signal.
 52
VOA
 Variable optical attenuator
Adjusts the optical power of the input optical signals.
 Driving and control module
Drives and controls the variable optical attenuator, and reports the detected attenuation to the control and communication module.
 Control and communication module
Controls the operations on the board.
Controls the operations on each module of the unit according to CPU instructions.
Collects the information of alarms, performance events, working states and voltage detection of each functional module of the unit.
Communicates with the SCC board.
 Power supply module
Converts the -48 V/-60 V DC power into the power required by each module of the board.
 53
HBA
 The HBA is mainly used to amplify C-band signals with high power.
 54
HBA

 EDFA optical module

Multiplexed signal light and pump light enter the erbium-doped fiber for amplification.
The erbium-doped fiber that is excited by the pump laser can amplify the optical signal to realize
the optical power amplification function.
The optical splitter splits some optical signals from the main optical path for optical power
detection.
The optical splitter splits some optical signals from the main optical path and provides them to
the MON interface for detection.
 55
HBA

 Drive and detection module

Detects in real time the optical power of service signals.

Detects in real time the drive current, backlight current, cooling current and operating
temperature of the pump laser inside the EDFA.

Drives the pump laser inside the EDFA optical module.

Reports alarms and performance events to the control and communication module.
 56
HBA

 Control and communication module

Controls the operations on the board.
Controls the operations on each module of the unit according to CPU instructions.
Collects the information of alarms, performance events, working states and voltage detection of
each functional module of the unit.
Communicates with the SCC board.
 Power supply module
Converts the -48 V/-60 V DC power into the power required by each module of the board.
Supports secondary power supply backup.
 57
HBA
 Functions and Features
 58
HBA
 Functions and Features
 59
HBA
 Optical Specifications
 60
OAU
 The OAU is used to amplify optical signals. The OAU can be used in both the transmit direction and the receive
direction.
 61
OAU
 EDFA optical module
Multiplexed signal light and pump light enter the erbium-doped fiber for amplification.
The erbium-doped fiber that is excited by the pump laser can amplify the optical signal to realize the optical power
amplification function.
The optical splitter splits some optical signals from the main optical path for optical power detection.
The optical splitter splits some optical signals from the main optical path and provides them to the MON interface for
detection.
The module is equipped with a electrical variable optical attenuator (EVOA), whose variable attenuation achieves gain
adjusting of a board.
 Power supply module
Converts the -48 V/-60 V DC power into the power required by each module of the board.
Supports secondary power supply backup.
 62
OAU
 Drive and detection module
Detects in real time the optical power of service signals.
Detects in real time the drive current, backlight current, cooling current and operating temperature of the pump laser
inside the EDFA.
Drives the pump laser inside the EDFA optical module.
Reports alarms and performance events to the control and communication module.
 Control and communication module
Controls the operations on the board.
Controls the operations on each module of the unit according to CPU instructions.
Collects the information of alarms, performance events, working states and voltage detection of each functional module
of the unit.
Communicates with the SCC board.
 63
OAU
 Functions and Features
 64
OAU
 Functions and Features
 65
OAU
 Optical specifications of the OAUC05
 66
OAU
 Optical specifications of the OAUC05
 67
OBU
 The OBU is used to amplify optical signals. The OBU is usually used in the transmitting direction.
 68
OBU
 EDFA optical module
Multiplexed signal light and pump light enter the erbium-doped fiber for amplification. The erbium-doped fiber that is
excited by the pump laser can amplify the optical signal to realize the optical power amplification function.
The optical splitter splits some optical signals from the main optical path for optical power detection.
The optical splitter splits some optical signals from the main optical path and provides them to the MON interface for
detection.
 Drive and detection module
Detects in real time the optical power of service signals.
Detects in real time the drive current, backlight current, cooling current and operating temperature of the pump laser
inside the EDFA.
Drives the pump laser inside the EDFA optical module.
Reports alarms and performance events to the control and communication module.
 69
OBU
 Control and communication module
Controls the operations on the board.
Controls the operations on each module of the unit according to CPU instructions.
Collects the information of alarms, performance events, working states and voltage
detection of each functional module of the unit.
Communicates with the SCC board.
 Power supply module
Converts the -48 V/-60 V DC power into the power required by each module of the board.
Supports secondary power supply backup.
 70
OBU
 Functions and Features
 71
OBU
 Functions and Features
 72
OBU
 Optical specifications of the OBUC05
 73
OBU
 Optical specifications of the OBUC05
 74
OPU
 The OPU is mainly used to amplify C-band signals. The OPU is usually used in the receiving direction.
 75
OPU
 EDFA optical module
Multiplexed signal light and pump light enter the erbium-doped fiber for amplification. The erbium-doped fiber that is
excited by the pump laser can amplify the optical signalto realize the optical power amplification function.
The optical splitter splits some optical signals from the main optical path for optical power detection.
The optical splitter splits some optical signals from the main optical path and provides them to the MON interface for
detection.
 Drive and detection module
Detects in real time the optical power of service signals.
Detects in real time the drive current, backlight current, cooling current and operating temperature of the pump laser
inside the EDFA.
Drives the pump laser inside the EDFA optical module.
Reports alarms and performance events to the control and communication module.
 76
OPU
 Control and communication module
Controls the operations on the board.
Controls the operations on each module of the unit according to CPU instructions.
Collects the information of alarms, performance events, working states and voltage detection of each functional
module of the unit.
Communicates with the SCC board.
 Power supply module
Converts the -48 V/-60 V DC power into the power required by each module of the board.
Supports secondary power supply backup.
 77
OPU
 Functions and Features
 78
OPU
 Functions and Features
 79
OPU
 OPU Board Specifications
 80
OPU
 OPU Board Specifications
 81
RPC
 The RPC is mainly used to generate pump light with multiple channels and high power to amplify the input optical
signals in C band and extended band. The total wavelengths range from 1529 nm to 1568 nm. The RPC is usually
used with the EDFA amplifier.

Functional block diagram of the backward pump RPC unit

 82
RPC
 Functional block diagram of the forward pump RPC unit
 83
RPC
 Raman pump optical module
The pump source generates pump light of high power for the distributed light amplification on the line.
The optical splitter splits some optical signals from the main optical path and provides them to the MON
interface for detection.
 Drive and detection module
Detects in real time the optical power of service signals.
Detects in real time the drive current, backlight current, cooling current and operating temperature of the pump
laser inside the pump optical module.
Drives the pump laser inside the pump optical module.
Reports alarms and performance events to the control and communication module.
 84
RPC
 Control and communication module
Controls the operations on the board.
Controls the operations on each module of the unit according to CPU instructions.
Collects the information of alarms, performance events, working states and voltage
detection of each functional module of the unit.
 Communicates with the SCC board.
 Power supply module
Converts the -48 V/-60 V DC power into the power required by each module of the board.
Supports secondary power supply backup.
 85
RPC
 Functions and Features
 86
RPC
 Functions and Features
 87
RPC
 Optical specifications of the RPC03
 88
SCC
 The SCC works with the NM to manages the s and transmits various maintenance and management message.
 89
SCC
 Control and processing module
Controls, monitors, and manages each functional module of the unit.
 Overhead processing module
Receives the overhead signals from service units and processes the overhead signals.
Sends the processed overhead signals to service units. Monitoring module
Detects whether each unit in the subrack is online, and reports the related alarms to the U2000.
 Clock module
Provides a clock source for the system.
Receives the clock signals from the OSC unit at the upstream station, and ensures that the local clock of the local unit is
synchronous with the clock.
Sends the local clock to the downstream station by using the OSC unit.
 90
SCC
 Communication module
Communicates with each unit in the subrack, and reports the data of other units to theU2000.
 Power supply module
Converts the -48 V/-60 V DC power into the power required by each module of the board.
DIP Switches and Jumpers
 J13: Used to detect the first PFU input. When the jumper cap is on
, it indicates that the -48V power supply is monitored; when the jumper
cap is off, the -60 V power supply ismonitored.
 J14: Used to detect the second PFU input. When the jumper cap is on
, it indicates that the -48 V power supply is monitored; when the jumper
cap is off, the -60 V power supply ismonitored.
 91
SCC
 Functions and Features
 92
SCC
 Functions and Features
 93
SC1
 The SC1 processes one supervisory channel. The SC1 transmits and extracts the overhead information of the
system, processes the information and sends it to the SCC.
 94
SC1
 Optical Receiving module
Performs O/E conversion of an optical supervisory signal.
 Optical transmitting module
Performs E/O conversion of an electrical supervisory signal.
 CMI encoding/decoding module
 Performs the mutual conversion between the 4 Mbit/s CMI-coded signal and the 2 Mbit/s
 signal.
 Overhead processing module
Frame processing: Performs framed signal processing functions, such as frame search,frame generation, CRC4 bit error
count, remote-end alarming and loss-of-frame (LOF) alarming. Overhead synchronization: Synchronizes overhead data
required for SCC
communication with the SCC clock (2M clock and 8K frame header signal).
 95
SC1
 Control and communication module
Controls the operations on the board.
Controls the operations on each module of the unit according to CPU instructions.
Collects the information of alarms, performance events, working states and voltage detection of each
functional module of the unit.
Communicates with the SCC board.
Provides the synchronization clock signals for each module.
 Power supply module
Converts the -48 V/-60 V DC power into the power required by each module of the board.
 96
SC1
 Frame Structure of the OSC Signals
 97
SC1
 Optical Specifications
 98
SC2
 The SC2 processes two supervisory channel. The SC2 transmits and extracts the overhead information of the
system, processes the information and sends it to the SCC.
 99
SC2
 Optical Receiving module
Performs O/E conversion of two optical supervisory signals.
 Optical transmitting module
Performs E/O conversion of two electrical supervisory signals.
 CMI encoding/decoding module
Performs the mutual conversion between the 4 Mbit/s CMI-coded signal and the 2 Mbit/ssignal.
 Overhead processing module
Frame processing: Performs framed signal processing functions, such as frame search, frame generation, CRC4 bit error
count, remote-end alarming and loss-of-frame (LOF) alarming.
Overhead synchronization: Synchronizes overhead data required for SCC
communication with the SCC clock (2M clock and 8K frame header signal).
 100
SC2
 Control and communication module
Controls the operations on the board.
Controls the operations on each module of the unit according to CPU instructions.
Collects the information of alarms, performance events, working states and voltage detection of each functional
module of the unit.
Communicates with the SCC board.
Provides the synchronization clock signals for each module.
 Power supply module
Converts the -48 V/-60 V DC power into the power required by each module of theboard.
 101
SC2
 SC2 Board Specifications
 102
OLP

 The E2OLP01 provide inter-subrack 1+1 optical channel protection for one working/protection OTU pair.
 The E2OLP02 provides inter-subrack 1+1 optical channel protection and extended intra-board wavelength
protection.
 The E2OLP03 provides optical line protection. There are two applications of E2OLP03 in optical line protection.
 Position of the E2OLP01/E2OLP02 in the WDM system ( inter-subrack 1+1 opticalchannel protection)
 103
OLP

 Position of the E2OLP02 in the WDM system (extended intra-board wavelength protection)
 104
OLP

 Position of the E2OLP03 in the WDM system (optical line protection, method 1)
 105
OLP

 Position of the E2OLP03 in the WDM system (optical line protection, method 2)
 106
OLP
 Functional block diagram of the OLP unit)
 107
OLP

 Optical module

The optical module consists of a signal dual-fed part and a signal selection part.

The signal dual-fed part divides the one channel of optical signals into two channels of the same
power, and outputs them to the working and protection channels.

The signal selection part receives the optical signals from the working and protection channels. The
optical power detecting module detects and compares the optical power of the two channels of
optical signals. Based on the results, the signal selection part elects one channel of optical signals
and outputs it.
 108
OLP
 Control and communication module
Controls the operations on the board.
Controls the operations on each module of the unit according to CPU instructions.
Collects the information of alarms, performance events, working states and voltage detection of
each functional module of the unit.
Communicates with the SCC board.
 Power supply module
Converts the -48 V/-60 V DC power into the power required by each module of the board.
Supports secondary power supply backup.
 109
OLP
 Optical interface parameter specifications of the E2OLP03 (single-mode)
 110
MCA
 The MCA is a type of spectrum analyzer unit. The MCA provides spectral analysis for optical signals.
 111
MCA
 The MCA unit consists of five parts: the 1 x 8 optical switch, the optical spectral analysis module,the driving
and control module, the control and communication module, and the power supplymodule.
 1 x 8 optical switch
Selects one channel of optical signals from the accessed eight channels of optical signals for spectrum analysis.
 Optical spectral analysis module
Monitors parameters such as the central wavelength, optical power, OSNR, and number of wavelengths.
 Driving and control module
Drives and controls spectrum.
Controls the 1 x 8 optical switch to select one channel of optical signals for spectrumanalysis.
 112
MCA
 Control and communication module
Controls the operations on the board.
Controls the operations on each module of the unit according to CPU instructions.
Collects the information of alarms, performance events, working states and voltage detection of
each functional module of the unit.
Communicates with the SCC board.
 Power supply module
Converts the -48 V/-60 V DC power into the power required by each module of theboard.
 113
MCA
 MCA Board Specifications
 114
Board Indicators

 Red alarm indicator

 115
Board Indicators

 Green running indicator

 Green running indicator on the SCC

 116
Board Indicators

 Running indicator and alarm indicator on the SCC

 Communication Indicator