Error, their types, their

measurements

Presented By:
Marta zeleke
What is an error?

Some are due to

human error…

For example,
by not using the
equipment correctly

Let’s look at
some examples.
 Human error

Example 1
Professor Messer
is trying to
measure the length of a
piece of wood:

Discuss what he is doing wrong.

How many mistakes
can you find? Six?
 Human error
Answers:

1.Measuring from 100 end

2.95.4 is the wrong number
3.‘mm’ is wrong unit (cm)
4.Hand-held object, wobbling
5.Gap between object & the rule
6.End of object not at the end of the rule
7.Eye is not at the end of the object (parallax)
8.He is on wrong side of the rule to see scale.
How many did you find?
Human error

Example 2 your
eye

Reading a scale:

Discuss the best position to

put your eye.
 Human error
your
2 is best. eye

1 and 3 give the

wrong readings.
This is called a
parallax error.

It is due to the gap here,

between the pointer and
the scale.

Should the gap be wide or narrow?

 ERRORS
If we are making physical measurements, there
is always error involved. The error is notated by
using the delta, Δ, symbol followed by the
variable representing the quantity measured.
For example, if we are measuring volume, the
error in measuring the volume would be
symbolized ΔV.
 Calculating the Error

A simple way of looking at the error is as the

difference between the true value and the
approximate value.
i.e:
Error (e) = True value – Approximate value
 TYPE OF ERRORS

Type of errors
1) Gross error/human Errors
Static Errors
2) Random Errors
3) Systematic Errors
4) Constant Errors
5) Absolute Errors
6) Relative Errors
7) Percentage Errors
 TYPES OF STATIC ERROR

1)Gross Error
 cause by human mistakes in reading/using
instruments
 may also occur due to incorrect adjustment of the
instrument and the computational mistakes
 cannot be treated mathematically
 cannot eliminate but can minimize
 Eg: Improper use of an instrument.
This error can be minimized by taking proper
care in reading and recording measurement
parameter.
 TYPES OF STATIC ERROR (cont)
2) Systematic Error
- due to shortcomings of the instrument (such as
defective or worn parts, ageing or effects of
the environment on the instrument)
 In general, systematic errors can be subdivided into
static and dynamic errors.
 Static – caused by limitations of the measuring
device or the physical laws governing its
behavior.
 Dynamic – caused by the instrument not
responding very fast enough to follow the
changes in a measured variable.
 TYPES OF STATIC ERROR (cont)

- 3 types of systematic error :-

(i) Instrumental error
(ii) Environmental error
(iii) Observational error
 TYPES OF STATIC ERROR (cont)
(i) Instrumental error
- inherent while measuring instrument because
of their mechanical structure (eg: in a D’ Arsonval
meter, friction in the bearings of various moving
component, irregular spring tension, stretching of
spring, etc)
- error can be avoid by:
(a) selecting a suitable instrument for the
particular measurement application
(b) apply correction factor by determining
instrumental error
(c) calibrate the instrument against standard
 TYPES OF STATIC ERROR (cont)
(ii) Environmental error
- due to external condition effecting the
measurement including surrounding area condition
such as change in temperature, humidity,
barometer pressure, etc
- to avoid the error :-
(a) use air conditioner
(b) sealing certain component in the instruments
(iii) Observational error
- introduce by the observer
- most common : parallax error and estimation error (while
reading the scale)
- Eg: an observer who tend to hold his head too far to the
left, while reading the position of the needle on the scale.
 TYPES OF STATIC ERROR (cont)

3) Random error
- due to unknown causes, occur when all systematic
error has accounted
- accumulation of small effect, require at high degree of
accuracy
- can be avoid by
(a) increasing number of reading
(b) use statistical means to obtain best approximation of
true value
 Systematic errors

Example 1
Suppose you are
measuring with a ruler:

If the ruler is wrongly calibrated,

or if it expands,

then all the readings will be too

low (or all too high):
 Systematic errors

Example 2
If you have a parallax error:

with your eye

always too high

then you will get a systematic error

All your readings will be too high.

 Systematic errors

A particular type of systematic error

is called a zero error.

Here are some examples . . .

 Zero errors

Example 3
A spring balance:

Over a period of time,

the spring may weaken,
and so the pointer
does not point to zero:

What effect does this have on all the readings?

Zero errors

Example 4
Look at this
top-pan balance:

It has a zero error.

There is nothing on it,
but it is not reading zero.

What effect do you think this will have

on all the readings?
Zero errors

Example 5
Look at this
ammeter:

If you used it like this,

what effect would it have
on your results?
Zero errors

Example 6
Look at this
voltmeter:

What is the first thing to

do?

Use a screwdriver here

to adjust the pointer.
Zero errors

Example 7
Look at this
ammeter:

What can you say?

Is it a zero error?
Or is it parallax?
Zero error, Parallax error

Example 8
Look at this ammeter:

It has a mirror
behind the pointer,
near the scale.

What is it for?
When
How cantheyou
image
useofit the pointer
to stop in theerror?
parallax mirror
is hidden by the pointer itself,
then you are looking at 90o, with no parallax.
 Random Errors

Random errors are “not inherent to the measuring process”. 

Frequently they are introduced by external factors that cause a

scattering of the measured data.

When the scattering is distributed equally about the true value,

the error can be mitigated somewhat by making multiple
measurements and averaging the data. 

• Vibration in mechanical devices produces random errors.

•  In electronic devices, noise produces random errors.   

Random errors

These may be due to

human error,
a faulty technique,
or faulty equipment.

To reduce the error,

take a lot of readings,
and then calculate the average (mean).
 Constant Error
• When the results of observation are in error
by the same amount, the error is said to be a
constant error. e.g. if a scale of 15 cm actually
measures 14.8 cm. Then it is measuring 0.2 cm
more in every observation. This type of error
will be same in all measurements done by the
scale.
 Another types of Error
Three other ways of defining the error are:

Absolute error
Relative error
Percentage error
 Calculation the Absolute Error
Absolute error.
ea = |True value – Approximate value|
 
ea = X  X =  Error 
'
 Calculating the Error
Absolute error:
ea = |True value – Approximate value|
 
ea = X  X =  Error 
'

Relative error is defined as:

Absolute Error X  X  '
er = = 
 True Value   X 
 Absolute Error
The difference between the measured value and
the true value is referred to as the absolute
error.
Assume that analysis of an iron ore by some
method gave 11.1% while the true value was
12.1%, the absolute error is:
12.1% -11.1% - = 1.0%

31
 Relative Error

The relative error is the percentage of the

absolute error to the true value. For the
argument above we can calculate the relative
error as:
Relative error = (absolute error/true
value)x100%
= (1.0/12.1)x100% = 8.3%

32
 Relative Accuracy
The percentage of the quotient of observed
result to the true value is called relative
accuracy.
Relative accuracy = (observed value/true
value)x100%
For the abovementioned example:
Relative accuracy = (11.1/12.1)x100% = 91.7%

33
 Calculating the Error
Percentage error is defined as:
X  X  '
e p = 100er = 100 
 X 
 Examples
Suppose 1.414 is used as an approx to 2 . Find
the absolute, relative and percentage errors.
2 = 1.41421356
ea = True value – Approximate value
(absolute error)

∴ ea = 1.41421356 - 1.414
= 0 . 00021356
 Examples
Suppose 1.414 is used as an approx to 2 . Find
the absolute, relative and percentage errors.
2 = 1.41421356
 Error 
er = 
True Value (relative error)

0.00021356 3
∴ er =  = 0.15110
 2 
 Examples

Suppose 1.414 is used as an approx to 2 . Find

the absolute, relative and percentage errors.

∴ e p =e r ×100 =0 .151×10−1 (percentage error)

Example:
True value = 122 mm
expected value = 120 mm

Then:
a. absolute error = True value - expected value
absolute error = 122 mm – 120 mm = 2 mm  Ans

b. relative error = absolute error / expected value

relative error = 2 mm / 120 mm =  0.017  Ans
Note: relative error has no units.

c. percent error = relative error · 100%

percent error = 0.017 · 100% =  1.7 %  Ans
 Classification of Error
The following are general classifications for errors:

1. For consumer purposes, 5-10% error is acceptable

2. For engineering purposes, 1% error is acceptable

3. For scientific purposes, 0.1% error is acceptable

 Range of Uncertainty
Range of uncertainty is reported as a nominal value plus or
minus an amount called the tolerance.

Reported value: 120 mm ±1 mm = 119 mm to 121 mm

nominal value tolerance range of uncertainty

 Range of Uncertainty
Range of uncertainty is reported as a nominal value plus or minus
an amount called the tolerance us an percent tolerance.

Reported value 120 mm ±2% = 117.6 mm to 122.4 mm

Note: 2%nominal 2.4, 120 - 2.4 =tolerance

of 120 =value range
117.6, 120 +2.4 of uncertainty
= 122.4
 PERFORMANCE CHARACTERISTICS
 Accuracy – the degree of exactness (closeness) of measurement
compared to the expected (desired) value.
 Resolution – the smallest change in a measurement variable to
which an instrument will respond.
 Precision – a measure of consistency or repeatability of
measurement, i.e successive reading do not differ.
 Sensitivity – ratio of change in the output (response) of instrument
to a change of input or measured variable.
 Expected value – the design value or the most probable value that
expect to obtain.
 Error – the deviation of the true value from the desired value.
 Precision – Target 1
Measurement precision must be interpreted in light of
measurement accuracy.  Let’s use a target practice example:

The best situation, the

shots are tightly
clustered (high
precision) on the center
circle (high accuracy).
 Precision – Target 2
Measurement precision must be interpreted in light of
measurement accuracy.  Let’s use a target practice example:

The next situation, shots

are near the center (high
accuracy), but not tightly
clustered (low
precision).  
 Precision – Target 3
Measurement precision must be interpreted in light of
measurement accuracy.  Let’s use a target practice example:

In the next situation, a

tight cluster (high
precision) is far off
center (low accuracy).
 Precision – Target 4
Measurement precision must be interpreted in light of
measurement accuracy.  Let’s use a target practice example:

Finally, widely scattered

shots (low precision)
appear away from the
center (low accuracy).
 Precision - Comparison
Which is the best and which is worst?

Best Worst Most Insidious

Why?
 Example

Given expected voltage value across a resistor is

80V.
The measurement is 79V. Calculate,
i. The absolute error
ii. The % of error
iii. The relative accuracy
iv. The % of accuracy
 Solution (Example)

Given that , expected value = 80V

measurement value = 79V

i. Absolute error, e = Y n − X=n80V – 79V = 1V

Yn  X n 80  79
ii. % error =   100
= = 100
1.25%
Y
 n  80
Yn  X n= 0.9875
iii. Relative accuracy, A = 1
 Yn 
iv. % accuracy, a = A x 100% = 0.9875 x 100% = 98.75%
 Example
From the value in table 1.1 calculate Table 1.1
the precision of 6th measurement? No Xn

1 98
Solution 2 101
3 102
the average of measurement value 4 97

98 +101+ .... + 99 1005 5 101

Xn = = = 100.5
10 10 6 100
the 6 reading Precision =
th
7 103


100  100.5
 0.5 8 98
1 = 1 = 0 . 995 9 106
 100.5  100.5 10 99
 LIMITING ERROR

 The accuracy of measuring instrument is

guaranteed within a certain percentage (%) of full
scale reading
 E.g manufacturer may specify the instrument to be
accurate at 2 % with full scale deflection
 For reading less than full scale, the limiting error
increases
 LIMITING ERROR (cont)
Example

Given a 600 V voltmeter with accuracy 2% full

scale.
Calculate limiting error when the instrument is
used to measure a voltage of 250V?
Solution
The magnitude of limiting error, 0.02 x 600 = 12V
Therefore, the limiting error for 250V = 12/250 x
100 = 4.8%
 LIMITING ERROR (cont)

Example
Given for certain measurement, a limiting error for
voltmeter at 70V is 2.143% and a limiting error for
ammeter at 80mA is 2.813%. Determine the limiting
error of the power.
Solution
The limiting error for the power = 2.143% + 2.813%
= 4.956%
In summary
• Human errors can be due to faulty technique.

• Parallax errors can be avoided.

• Anomalous results can be seen on a graph.

• Random errors can be reduced by taking many

readings, and then calculating the average
(mean).

• Systematic errors, including zero errors, will

cause all your results to be wrong.