Air & Draft system
July 10, 2011 PMI Revision 00 1
Presentation Plan
Various auxiliary equipments in a boiler Need for Draft System Primary and secondary air system in Boiler and their fans Other fans in a boiler Basic of fans: Fan Types and selection Fan laws and factors affecting fan performance Performance curves
July 10, 2011
PMI Revision 00
Arrangement of Boiler Auxiliaries
July 10, 2011
PMI Revision 00
Need of Draft System
Combustion Air
Boiler
Flue Gases
Air needed for combustion Flue are needed to be evacuated Losses due to flow need to be overcome
July 10, 2011 PMI Revision 00 4
How to select a fan
Air or Gas flow -Kg/hr Density (function of temperature and pressure) System, resistance (losses) Major Fans in Boiler Draft System PA Fans FD Fans ID Fans
July 10, 2011
PMI Revision 00
PRIMARY AIR/MILL SEAL AIR SYSTEM
Ambient air is drawn into the primary air ducting by two 50% duty, motor driven axial reaction fans. Air discharging from each fan is divided into two parts, one passes first through a air preheater then through a gate into the P.A bus duct. The second goes to the cold air duct. The mix of both is used to carry the pulverized coal to the boiler.
July 10, 2011 PMI Revision 00 6
Components of PA Fan
Suction Bend With volume Measurement instruments Fan housing with Guide Vanes Main Bearings (Anti Friction) Rotor with impeller with adjustable blade with pitch control Guide vane housing with guide vanes Diffuser with pressure measurement instruments
July 10, 2011 PMI Revision 00 7
SECONDARY AIR SYSTEM
Ambient air is drawn into the secondary air system by two 50% duty, motor driven axial reaction forced draft fans with variable pitch control. Air discharging from each fan passes first through a air preheated then through a isolating damper into the secondary air bust duct. The cross over duct extends around to each side of the boiler furnace to form two secondary air to burner ducts. At the sides of the furnace, the ducts split to supply air to two corners. Then split again to supply air to each of nineteen burner/air nozzle elevations in the burner box.
July 10, 2011
PMI Revision 00
Burner Box Dampers
Coal/Air Dampers Secondary Air Dampers Oil/Secondary Air Dampers Bottom Tier Secondary Air Damper Over Fire Damper
July 10, 2011
PMI Revision 00
Primary and Secondary air System in the Boiler
July 10, 2011
PMI Revision 00
10
Axial Fans FD Application
July 10, 2011
PMI Revision 00
11
Induced Draft System
There are three induced draught fans per boiler, two operating and one standby In 500 MW fans are single-stage, doubleinlet centrifugal fans. Principal fan elements of the fan are: Housing Inlet dampers Rotor with Bearing Shaft Seal
July 10, 2011 PMI Revision 00 12
ID Fan
The rotor consists of shaft and assembled impeller and runs in two sleeve bearings that are arranged outside of the housing. The impeller consists of a centre disc and two cover discs that are reinforced by forged rings. The bent blades are welded into position between the impeller discs. The blades are protected by screwed - on wear plates. The shaft is of hollow design. The fan shaft has been rated so that max. operating speed is below the critical speed. Impeller and shaft are connected by means of a flange. This screwing is protected by wear plates. The fan housing is sealed by means of two-part labyrinth seals. Bearings are lubricated with oil.
July 10, 2011
PMI Revision 00
13
Other Fans in The System
Ignitor Air Fan: Provide combustion air to the ignitors. Take suction air from the atmosphere and supplies air to the ignitor wind box. Scanner Air Fan: Supplies cooling air to flame scanners. Normally there are two fans taking suction from FD Fan discharge duct. Mill Seal air fan: Seal air fans provide air for the sealing of Mill bearing. Suction is from cold Primary air and pressure is boosted up to maintain the differential pressure
July 10, 2011
PMI Revision 00
14
AIR AND FLUE GAS PATH TYPICAL 500 MW BOILER
TO MILLS
PAPH-A
PRIMARY
ECO BYPASS
SCAPH-A
PA FAN -A
TO ESP
SAPH-A
AA205
AA203
SCAPH-A SECOND
AEROFOIL
AA202
AA201
HORIZONTAL S.H
ECONOMISER -1
DIVISION PANELETTE S.H
ECONOMISER -2
ECONOMISER-3
SA HDR
AA204
FD FAN -B
PLATEN S.H
HOT
COMBUSTION CHAMBER
RE HEATER
HOT PA HDR
AA204
AA201
SAPH-B
AA205
AA203
SCAPH-B SECOND
AA202 FD FAN-A
AEROFOIL
COLD SEC. AIR COLD PRIM AIR HOT PRIMARY AIR HOT SEC. AIR FLUE GAS PNEUMATICALLY O/P KNIFE EDGE GATE MOTOR O/P LOUVER DAMPER PNEUMATICALLY O/P LOUVER DAMPER
BIPLANE DAMPER DIVERTER DAMPER
ECO BYPASS
TO ESP
TO MILLS PA FAN -A
July 10, 2011 MOTOR O/P GATE
PMI Revision 00
PAPH-B
SCAPH-B
PRIMARY
15
Scheme of Air and Gas Path
July 10, 2011
PMI Revision 00
16
ID Fan at Location
July 10, 2011
PMI Revision 00
17
Variation of Pressure in Boiler
Furnace P ressure At Various P oints in B oiler
250 200 150 100 50 Furnace Pressure 0 1 -50 -100 -150 -200 -250 -300 Points in Boiler 2 3 4 5 6 7 8 9 10 11 12 13 14
1FD Fan Inlet 2FD Fan Outlet 3Airheater Inlet 4Airheater Outlet 5Windbox Pressure 6Furnace 7Superheater Platen Inlet
8Reheater Inlet 9LTSH Inlet 10Economiser Inlet 11Airheater Inlet 12E.P. Inlet 13I.D. Fan Inlet
July 10, 2011
PMI Revision 00
14I.D. Fan Outlet
18
Basics on Fans
July 10, 2011
19
Difference between fans, blowers and compressors
As per ASME the specific pressure, i.e, the ratio of the discharge pressure over the suction pressure is used for defining the fans, blowers and compressors as highlighted below :
Equipment Fans Blowers Compressors
July 10, 2011
Specific Ratio Up to 1.11 1.11 to 1.20 more than 1.20
Pressure rise (mmWg) 1136 1136 2066 20
PMI Revision 00
Typical centrifugal fan operation
July 10, 2011
PMI Revision 00
21
Fan types
Centrifugal fan
July 10, 2011 PMI Revision 00
Axial fan
22
Centrifugal Fan: Types
Paddle Blade (Radial blade)
Forward Curved (Multi vane)
Backward Curved
July 10, 2011
PMI Revision 00
23
Axial Flow Fan: Types
Tube Axial Vane Axial Propeller
July 10, 2011
PMI Revision 00
24
Fan Types and Efficiencies
Peak Efficiency Range Airfoil, backwardly curved/inclined 79-83 Modified radial 72-79 Redial 69-75 Pressure blower 58-68 Forwardly curved 60-65 Axial fan vanaxial 78-85 Tubeaxial 67-72 Propeller 45-50 Centrifugal Fans
July 10, 2011 PMI Revision 00 25
Axial -flow Fans Type Prope ller Characteristics Low pressure, high flow, low efficiency, peak efficiency close to point of free air delivery Medium pressure, high flow, higher effici ency than propeller type, dip in pressure -flow curve before peak pressure point. High pressure, medium flow, dip in pressure -flow curve, use of guide vanes improves efficiency Typical Applications Aircircul ation, ventilation, exhaust HVAC, drying ovens, exhaust systems Type Radial
Centrifugal Fans Characteristics High pressure, medium flow, efficiency close to tube-axial fans, power increases continuously Medium pressure, high flow, dip in pressure curve, efficiency higher than radial fans, power rises continuously High pressure, high flow, high efficiency, power reduces as flow increases beyond point of highest efficiency Same as backward curved type, highest efficiency Typical Applications Various industrial applications, suitable for dust laden, moist air/gases Low p ressure HVAC, packaged units, suitable for clean and dust laden air / gases
Tubeaxial
Forward curved blades
Vane axial
High pressure applications including HVAC systems, exhausts
Backward curved blades
HVAC, various industrial applications, forced draft fans, etc.
Airfoil type
July 10, 2011 PMI Revision 00
Same as backward curved, but for clean air applications
26
System characteristic curve
July 10, 2011
PMI Revision 00
27
July 10, 2011
PMI Revision 00
28
System curve
July 10, 2011
PMI Revision 00
29
Fan Laws
Flow ? Speed Pressure ? (Speed)2 Power ? (Speed)3
Q1 N 1 = Q2 N 2
SP1 N 1 = SP 2 N 2
kW 1 N 1 = kW 2 N 2
Varying the RPM by 10% decreases or increases the power requirement by 27%.
30
Varying the RPM by 10% Varying the RPM by 10% decreases or increases air decreases or increases the delivery by 10%. static pressure by 19%.
Where Q flow, SP Static Pressure, kW Power and N speed (RPM)
July 10, 2011 PMI Revision 00
Fan static pressure
Fan Static Pressure SP = SP (Fanoutlet) SP (Faninlet)
SP (Fanoutlet) Static pressure at fan outlet, mm WC SP (Faninlet) Static pressure at fan inlet, mm WC
SP = 0.05 (-10) = 10.05 mm W.C.
July 10, 2011 PMI Revision 00 31
Speed vs Power
% Speed 100 90 80 70 60 50
July 10, 2011
% Power 100 73 51 34 22 13
PMI Revision 00 32
Flow control Damper - Most Popular Variable Speed Drive
Recirculation Damper VFC
100
Power
75 50 25 25 50 75 100
VFD Ideal
Flow
July 10, 2011
PMI Revision 00
33
Impact of speed reduction
July 10, 2011
PMI Revision 00
34
Use of VSD: Boiler ID fan case study
July 10, 2011
PMI Revision 00
35
Use of VSD: Boiler ID fan case study (contd.)
July 10, 2011
PMI Revision 00
36
July 10, 2011
PMI Revision 00
37
July 10, 2011
PMI Revision 00
38
July 10, 2011
PMI Revision 00
39
THANK YOU
July 10, 2011
PMI Revision 00
40
