Animatronic hand controller

Project Final Report
Animatronic Hand Controller
Group-5(Mas-Cube)
Department of EEE, Ahsanullah University of Sciene And Technology,Dhaka,Bangladesh
Team members
Oshin_sabrina@yahoo.com
kazisadman047@gmail.com
mowleemannan@gmail.com
afrozahaque77@gmail.com
ananto.tr@gmail.com
Project Abstract-
For some time, We have been interested in
making some sort of robot based on the Arduino
platform. This project is the first phase of this
longer-term desired effort. Anything is possible
with the mighty power of Arduino. It's
compact, it's straightforward, and makes
embedding electronics into the world-at-large
fun and easy.
Animatronics is the use of mechatronics to create
machines which seem animate rather than
robotic. Animatronic figures are most often
powered by pneumatics (compressed air), and,
in special instances, hydraulics (pressurized oil),
or by electrical means. The figures are precisely
customized with the exact dimensions and
proportions of living creatures. Motion
actuators are often used to imitate “muscle”
movements, such as limbs to create realistic
motions. Also, the figure is covered with body
shells and flexible skins made of hard and soft
plastic materials. Then, the figure can be
finished by adding details like colors, hair and
feathers and other components to make the
figure more realistic.
The project idea came to us after watching the
movie named “Real Steel”. We wanted to make
a shadow robot from our curiosity. As the whole
body of the robot would have been of much
cost, We decided to make a shadow hand
instead. Approximating the kinematics of the
human hand was our top priority when
developing this animatronic hand. Each joint
of this hand has a movement range again the
same as or very close to that of a human hand,
including the thumb and even the flex of the
palm for the little finger.
Keywords- Arduino, Servo motors, Flex
sensors, Power IC, Programming of the
Arduino.
I. INTRODUCTION

This paper mainly analysis about different
topologies and designs regarding the construction
of this Arduino based animatronic hand. Although
more complicated and precise(more expensive)
versions of this concept have been developed, this
is a fun project with many potential applications.
Interactive robot control of this level, I think, has
many uses in industrial manufacturing, medical
research, and anything you want to be able to do
with precision that is unsafe to touch.
The basic components of the hand and glove are
the hand itself, the servos, the Arduino, the glove,
and the flex sensors. The glove is mounted with
flex sensors: variable resistors that change their
value when bent. They're attached to one side of a
voltage divider with resistors of a constant value on
the other side. The Arduino reads the voltage
change when the sensors are bent, and triggers the
servos to move a proportional amount. The servo
pull strings that act as tendons, allowing the fingers
to move.
I. STATUS OF THE PROJECT
This project has been completed successfully, and
my goal of integrating all of the underlying
technologies has been met.
This animatronic hand is able to be controlled
according to the controller’s wish. It’s capable of
moving at the required degrees of freedom. It can
also pick up things upto minimum desired weight .
Now, we can use it as a shadow hand of ours which
is of various use. With the help of sensors, this
hand can now provide detailed telemetry, which
can be exploited to generate innovative
manipulation control systems or to provide detailed
understanding of the external environment.
In the sections that follow, I will describe various
outstanding areas that could stand to see some
further refinement.
II. DESIGN
A. SYSTEM OVERVIEW
1. WORKING PRINCIPAL OF ARDUINO
HARDWARE-
The Arduino microcontroller is an easy to use yet
powerful single board computer that has gained
considerable traction in the hobby and professional
market. The Duemilanove board features an Atmel
ATmega328 microcontroller operating at 5 V with
2 Kb of RAM, 32 Kb of flash memory for storing
programs and 1 Kb of EEPROM for storing
Parameters. The clock speed is 16 MHz, which
translates to about executing about 300,000 lines
of C source code per second. The board has 14
digital I/O pins and 6 analog input pins. There is
a USB connector for talking to the host computer
and a DC power jack for connecting an external 6-
20 V power source, for example a 11.1 V battery,
when running a program while not connected to the
host computer. Headers are provided for interfacing
to the I/O pins using 22 g solid wire or header
connectors.
The Arduino programming language is a simplified
version of C/C++. If you know C, programming the
Arduino will be familiar. If you do not know C, no
need to worry as only a few commands are needed
to perform useful functions. An important feature
of the Arduino is that we can create a control
program on the host PC, download it to the
Arduino and it will run automatically. Remove the
USB cable connection to the PC, and the program
will still run from the top each time you push the
reset button. Remove the battery and put the
Arduino board in a closet for six months. When
you reconnect the battery, the last program you
stored will run. This means that you connect the
board to the host PC to develop and debug your
program, but once that is done, you no longer need
the PC to run the program.

The power of the Arduino is not its ability to
crunch code, but rather its ability to interact with
the outside world through its input-output (I/O)
pins. The Arduino has 14 digital I/O pins labeled
0 to 13 that can be used to turn motors and lights
on and off and read the state of switches. Each
digital pin can sink or source about 40 mA of
current. This is more than adequate for interfacing
to most devices, but does mean that interface
circuits are needed to control devices other than
simple LED's. In other words, you cannot run a
motor directly using the current available from an
Arduino pin, but rather must have the pin drive an
interface circuit that in turn drives the motor. A
later section of this document shows how to
interface to a small motor. To interact with the
outside world, the program sets digital pins to a
high or low value using C code instructions, which
corresponds to +5 V or 0 V at the pin. The pin is
connected to external
interface electronics and then to the device being
switched on and off. The sequence of events is
shown in this figure.
To determine the state of switches and other
sensors, the Arduino is able to read the voltage
value applied to its pins as a binary number. The
interface circuitry translates the sensor signal
into a 0 or +5 V signal applied to the digital I/O
pin. Through a program command, the Ardiomp
interrogates the state of the pin. If the pin is at 0 V,
the program will read it as a 0 or LOW. If it is at +5
V, the program will read it as a 1 or HIGH. If more
than +5 V is applied, you may blow out your board,
so be careful. The sequence of events to read a pin
is shown in this figure:
Interacting with the world has two sides. First, the
designer must create electronic interface
circuits that allow motors and other devices to be
controlled by a low (1-10 mA) current signal
that switches between 0 and 5 V, and other circuits
that convert sensor readings into a switched 0
or 5 V signal. Second, the designer must write a
program using the set of Arduino commands
that set and read the I/O pins.
When reading inputs, pins must have either 0 or 5V
applied. If a pin is left open or "floating", it will
read random
voltages and cause erratic results. This is why
switches always have a 10K pull up resistor
connected when
interfacing to an Arduino pin.
The reason to avoid using pins 0 and 1 is because
those pins are used for the serial communications
between
the Arduino and the host computer. The Arduino
also has six analog input pins for reading
continuous voltages in the range of 0 to 5
V from sensors such as potentiometers.
2. WORKING PRINCIPAL OF SERVO
MOTOR-
Unlike dc motors, with servo motors you can
position the motor shaft at a specific position
(angle) using control signal. The motor shaft will
hold at this position as long as the control signal
not changed. This is very useful for controlling
robot arms, unmanned airplanes control surface or
any object that you want it to move at certain angle
and stay at its new position. Servo motors may be
classified according to size or torque that it can
withstand into mini, standard and giant servos.
Usually mini and standard size servo motors can be

powered by Arduino directly with no need to
external power supply or driver.
The servo have 3 wires:
Black wire: GND (ground) !
RED wire:+5v !
Colored wire: control signal
The third pin accept the control signal which is a
pulse-width modulation (PWM) signal. It can be
easily produced by all micro- controllers and
Arduino board. This accepts the signal from your
controller that tells it what angle to turn to. The
control signal is fairly simple compared to that of a
stepper motor. It is just a pulse of varying lengths.
The length of the pulse corresponds to the angle the
motor turns to.
The pulse width sent to servo ranges as follows:
Minimum: 1 millisecond ---> Corresponds to 0
rotation angle.
Maximum: 2 millisecond ---> Corresponds to 180
rotation angle.
Any length of pulse in between will rotate the servo
shaft to its corresponding angle. For example : 1.5
ms pulse corresponds to rotation angle of 90
degree.
This is will explained in figure below:
3.WORKING PRINCIPAL OF FLEX SENSOR-
Flex sensors are sensors that change in resistance
depending how much the sensor is bend.
Sensors convert the change in bend to electrical
resistance - the more the sensor bend, the higher
the resistance value. Using the Flex Sensor is very
easy. There are couple of different manufacturers
in the market.
Datasheet instructs you to use operational amplifier
(opamps). That may be useful if you plan to use
flex sensor as stand-alone device (without any
microcontroller).Because We are using arduino,
We skipped all OpAmps and made a very simple
circuit with only one additional resistor.
Varying the value of the resistor will results
different readings. With 22k Ohm resistor I will
get values between 300-700. This works fine for
us. In our code we assumed that all values under
400 mean that the sensor is bend. All values above
600 mean that sensor is nor bend. Note that Flex
sensor give reliable readings ONLY if you bend it
on the specific direction (usually towards on the
text side of the sensor).

4. Motor Control Using Arduino-
A. OPERATING ONE SERVO WITH
ARDUINO:
Standard servo motor control using Arduino is
extremely easy. This is because the Arduino
software comes with a sample servo sketch and
servo library that will get you up and running
quickly:
1. Connect the black wire from the servo to the
Gnd pin on the Arduino
2. Connect the red wire from the servo to the +5V
pin on the Arduino
3. Connect the third wire (usually orange or
yellow) from the servo to a digital
pin on the Arduino.
# Important Notes:
1- It is not a good idea to connect a motor of any
kind directly to the Arduino because it usually
requires more power than the board can provide.
2- In our example, the servo is being used to
demonstrate code and is not encountering any
resistance. Note that you should use a standard or
small size. if you are uncertain, check the servo's
no load current rating (it should usually be
under 150mA).
3-You may need an external source of 5 or 6 volts
when connecting multiple servos. Four AA cells
work well if you want to use battery power.
Remember that you must connect the ground of
the external power source to Arduino ground.
B. OPERATING TWO SERVO WITH
ARDUINO:
The Arduino can control two servos with the same
ease as one. All it takes is creating a second
instance (copy) of the Servo object, giving it a
unique name. In this project we had to use six
servos, five of which has to connect directly with
arduino at the same process of connecting one
servo with arduino. When wiring the solderless
breadboard, be especially careful not to mix
positive and negative leads to the servo.
Reversing the power will permanently damage
it.
In order for everything to function properly, the
ground connections for the Arduino and the servo
battery supply must be connected together.This is
shown in both the schematic and pictorial circuit
views. Make sure to also properly orient the
connectors for the servos when you plug them into
the board. Servo power leads are color-coded, but
the colors aren’t universal. Here two servos are
being connected with the arduino in the figure
given below:-

C. SYSTEM ALGORITHM
1. ARDUINO PROGRAMMING CODING
STYLE:-
The Arduino runs a simplified version of the C
programming language, with some extensions for
accessing the hardware. All Arduino instructions
are one line. The board can hold a program
hundreds of lines long and has space for about
1,000 two-byte variables. The Arduino executes
programs at about 300,000 source code lines per
sec. Programs are created in the Arduino
development environment and then downloaded to
the Arduino board. Code must be entered in the
proper syntax which means using valid command
names and a valid grammar for each code line. The
compiler will catch and flag syntax errors.
before download. Sometimes the error message
can be cryptic and you have to do a bit of hunting
because the actual error occurred before what was
flagged.
Style refers to our own particular style for creating
code and includes layout, conventions for
using case, headers, and use of comments. All code
must follow correct syntax, but there are many
different styles we can use. Here are some
suggestions:
 Starting every program with a comment header
that has the program name and perhaps a brief
description of what the program does.
 Using indentation to line things up. Function
name and braces are in column one. Mark major
sections or functions with a comment header line or
two.
Having just the right number of comments, not
too few and not too many. Assume the reader
knows the programming language so have the
comment be instructive. Here is an example of an
instructive comment
digitalWrite(4,HIGH) // turn on
motor
and here is a useless comment
digitalWrite(4,HIGH) // set pin 4
HIGH
we need not comment every line. In fact,
commenting every line is generally bad practice.
 Adding the comments when you create the code.
If you tell yourself, "Oh, I'll add the comments
when the code is finished", you will never do it.
2.THE PROCESSING CODE:-
The processing code of our project is given below:-
#include <Servo.h>
int flexSensorPin1 = A0;
Servo
servo1,servo2,servo3,servo4,ser
vo5,servo6;
void setup(){
Serial.begin(9600);
servo1.attach(9);
servo2.attach(8);
servo3.attach(7);
servo4.attach(6);
servo5.attach(5);
servo6.attach(4);
pinMode(flexSensorPin1,INPUT);
}
int pos=0;
void loop(){
int
fsr1=analogRead(flexSensorPin1)
;
//myServo.write(x);
//Serial.println(fsr);
int s1=map(fsr1, 605, 696, 180,
0);
Serial.println(s1);
if(s1>0 ||s1<180)
servo1.write((s1));
delay(100);
int
;
//myServo.write(x);
int s2=map(fsr2, 605, 696, 180,
0);
Serial.println(s2);
if(s2>0 ||s2<180)
servo2.write((s2));
delay(100);
int
;
//myServo.write(x);

//Serial.println(fsr);
int s3=map(fsr3, 605, 696, 180,
0);
Serial.println(s3);
if(s3>0 ||s3<180)
servo3.write((s3));
delay(100);
int
;
//myServo.write(x);
int s4=map(fsr4, 605, 696, 180,
0);
Serial.println(s4);
if(s4>0 ||s4<180)
servo4.write((s4));
delay(100);
int
;
//myServo.write(x);
int s5=map(fsr5, 605, 696, 180,
0);
Serial.println(s5);
if(s5>0 ||s5<180)
servo5.write((s5));
delay(100);
int
;
//myServo.write(x);
int s6=map(fsr6, 605, 696, 180,
0);
Serial.println(s6);
if(s6>0 ||s6<180)
servo6.write((s6));
delay(100);
3.THE CODING STRUCTURE ANALYSIS:
In the program above, the very first thing that we
did in the setup function is to begin serial
communications, at 9600 bits of data per second,
between our Arduino and our computer with the
line:
Serial.begin(9600);
Next, initialize digital pin 8, the pin that will read
the output from your button, as an input:
pinMode(A8,INPUT);
Now let’s move into the main loop of your code.
A. FUNCTIONS:
1.ARDUINO PROGRAM FUNCTION
All Arduino programs have two functions, setup()
and loop().Other functions must be created outside
the brackets of those two functions. The
instructions you place in the startup() function are
executed once when the program begins and are
used to initialize. Use it to set directions of pins or
to initialize variables. The instructions placed in
loop are executed repeatedly and form the main
tasks of the program. Therefore every program has
this structure:
void setup()
{
// commands to initialize go here
}
void loop()
{
// commands to run your machine go
here
}
The absolute, bare-minimum, do-nothing program
that we can compile and run is
void setup() {} void loop() {}
The program performs no function, but is useful for
clearing out any old program. Note that the
compiler does not care about line returns, which is
why this program works if typed all on one
line.
2.Void() : The void keyword is used only in
function declarations. It indicates that the function
is expected to return no information to the function
from which it was called.
3.SERVO CONTROL PROGRAMMING:
There are two main portions of code that you'll see
explained and in detail below:
-Initialization
-Servo Control
The first part of the code shows you how to
initialize the servo and all our variables, this is
important if you want to use more than 1 servo you
need to declare that. We'll be using the Arduino
Servo library for all out control to make things as
easy as possible.
Initialization
------------« Begin Code »------------
#include <Servo.h>
Servo myservo; // create servo
object to control a servo
// a maximum of
eight servo objects can be created
void setup()
{
myservo.attach(0); // attaches
the servo on pin 0 to the servo
object

delay(5000);
}
..
...
------------« End Code »------------
The last portion of the code is where we actually
tell the servo where to move using the write
function of the Arduino's Servo library.
Main Loop
------------« Begin Code »------------
...
..
void loop()
{
//Move To 0 Degrees
myservo.write(10);
delay(5000);
//Move To 45 Degrees
myservo.write(45);
delay(5000);
myservo.write(90);
delay(5000);
myservo.write(135);
delay(5000);
myservo.write(170);
delay(5000);
myservo.write(135);
delay(5000);
myservo.write(90);
delay(5000);
myservo.write(45);
delay(5000);
}
------------« End Code »------------
B. The Simple Commands:-
This section covers the small set of commands we
needed to make the Arduino being operated
properly.
1. Serial.begin()
Description: Sets the data rate in bits per second
(baud) for serial data transmission. For
communicating with the computer, use one of these
rates: 300, 600, 1200, 2400, 4800, 9600, 14400,
19200, 28800, 38400, 57600, or 115200. You can,
however, specify other rates - for example, to
communicate over pins 0 and 1 with a component
that requires a particular baud rate. An optional
second argument configures the data, parity, and
stop bits. The default is 8 data bits, no parity, one
stop bit.
Syntax:
Serial.begin(speed)
Serial.begin(speed, config)
Arduino Mega only:
Serial1.begin(speed)
Serial1.begin(speed, config)
Parameters:
speed: in bits per second (baud) – long.
2. servo.attach()
Description:-Attach the Servo variable to a pin.
Note that in Arduino 0016 and earlier, the Servo
library supports only servos on only two pins: 9
and 10.
Syntax:servo.attach(pin)
servo.attach(pin, min, max)
Parameters:servo: a variable of type Servo pin: the
number of the pin that the servo is attached to
min (optional): the pulse width, in microseconds,
corresponding to the minimum (0-degree) angle on
the servo (defaults to 544)
max (optional): the pulse width, in microseconds,
corresponding to the maximum (180-degree) angle
on the servo (defaults to 2400).
3. pinMode()
Description: Configures the specified pin to
behave either as an input or an output.This
command, which goes in the setup() function, is
used to set the direction of a digital I/O pin. Set the
pin to OUTPUT if the pin is driving and LED,
motor or other device. Set the pin to INPUT if the
pin is reading a switch or other sensor. On power
up or reset, all pins default to inputs.
Syntax: pinMode(pin, mode)
Parameters:
pin: the number of the pin whose mode you wish to
set
mode: INPUT, OUTPUT,
Returns : None
4. serial.print()

Description: The Serial.print command lets
you see what's going on inside the Arduino
from your computer.
For example, we can see the result of a math
operation to determine if you are getting the
right
number. Or, we can see the state of a digital
input pin to see if the Arduino is a sensor or
switch
properly. When our interface circuits or
program does not seem to be working, use the
Serial.print command to shed a little light on
the situation. For this command to show
anything,
you need to have the Arduino connected to the
host computer with the USB cable.
For the command to work, the command
Serial.begin(9600) must be placed in the
setup()
function. After the program is uploaded, we
must open the Serial Monitor window to see
the
response.
There are two forms of the print command.
Serial.print() prints on the same line while
Serial.println() starts the print on a new line.
Here is a brief program to check if your board
is alive and connected to the PC
void setup()
{
Serial.begin(9600);
Serial.println("Hello World");
}
void loop() {}
Here is a program that loops in place,
displaying the value of an I/O pin. This is
useful for
checking the state of sensors or switches and
to see if the Arduino is reading the sensor
properly.
Try it out on your Arduino. After uploading
the program, use a jumper wire to alternately
connect pin 2 to +5V and to Gnd.
void setup()
{
Serial.begin(9600);
}
void loop()
{
Serial.println(digitalRead(2));
delay(100);
}
If we wanted to see the states of pins 2 and 3
at the same time, you can chain a few print
commands, noting that the last command is a
println to start a new line.
void setup()
{
Serial.begin(9600);
}
void loop()
{
Serial.print("pin 2 = ");
Serial.print(digitalRead(2));
Serial.print(" pin 3 = ");
Serial.println(digitalRead(3));
21
delay(100);
}
5. analogRead()
Description: Reads the value from
the specified analog pin. The
Arduino board contains a 6 channel
(8 channels on the Mini and Nano,
16 on the Mega), 10-bit analog to
digital converter. This means that it
will map input voltages between 0
and 5 volts into integer values
between 0 and 1023. This yields a
resolution between readings of: 5
volts / 1024 units or, .0049 volts
(4.9 mV) per unit. It takes about
100 microseconds (0.0001 s) to
read an analog input, so the
maximum reading rate is about
10,000 times a second.
Syntax : analogRead(pin)
Parameters : pin: the number of the analog
input pin to read from (0 to 5 on most boards,
0 to 7 on the Mini and Nano, 0 to 15 on the
Mega)
Returns:- int (0 to 1023)
6. map(value, fromLow, fromHigh,
toLow, toHigh)
Description: Re-maps a number from one
range to another. That is, a value of fromLow
would get mapped to toLow, a value of
fromHigh to toHigh, values in-between to
values in-between, etc. Does not constrain

values to within the range, because out-of-
range values are sometimes intended and
useful. The constrain() function may be used
either before or after this function, if limits to
the ranges are desired. Note that the "lower
bounds" of either range may be larger or
smaller than the "upper bounds" so the map()
function may be used to reverse a range of
numbers, for example
y = map(x, 1, 50, 50, 1);
The function also handles negative numbers
well, so that this example
y = map(x, 1, 50, 50, -100); is
also valid and works well.
The map() function uses integer math so will
not generate fractions, when the math might
indicate that it should do so. Fractional
remainders are truncated, and are not rounded
or averaged.
Parameters :
value: the number to map
fromLow: the lower bound of the value's
current range
fromHigh: the upper bound of the value's
current range
toLow: the lower bound of the value's target
range
toHigh: the upper bound of the value's target
range
Returns: The mapped value.
7. If
Description: This is the basic conditional
branch instruction that allows your program to
do two different things depending on whether
a specified condition is true or false. If the
condition is true, the program will execute the
commands between the braces. If the condition
is not true, the program will skip to the statement
following the braces.The condition compares one
thing to another.
delay()
Description: Pauses the program for the amount of
time (in miliseconds) specified as parameter.
(There are 1000 milliseconds in a second.) Since
most interactions with the world involve timing,
this is an essential instruction. The delay can be for
0 to 4,294,967,295 msec. In the project we used
delay(100); // waits 50 ms
Syntax:delay(ms)
Parameters:
ms: the number of milliseconds to pause (unsigned
long)
Returns: nothing.
III. SPECIFICATION
A. HARDWARE DETAILS
PARTS LIST:
COMPONENTS SPECIFIC
ATION
QUANT
ITY
(Unit)
1. ARDUINO MEGA
2560
1
2. SERVO
MOTOR
SG90
(2.5K)
3
3. SERVO MOTOR MG996R(
10K)
2
4. SERVO MOTOR SMS4315
(14K
TORQUE
)
1
5. BREAD BOARD SOLDER
LESS
1
6. JUMPER WIRE MALE,
FEMALE
, MALE-
FEMALE
3
7. FLEX SENSOR 4.5” 5
8. BATTERY 11.1V 1
9. BATTERY
CHARGER
N/A 1
10. CHARGER
CONNECTING
CABLE
N/A 1

11. POWER IC N/A 2
12. PCB N/A 2
13. RESISTORS 22K 5
14. POT 10K ,
100K
2
15. STRING N/A 5
16. NEEDLE &
THREAD
N/A 1
17. SUPER GLUE N/A 1
18. A POWER DRILL N/A 1
19. SPRING N/A 10
20. RIGHT HAND
GLOVE
N/A 1
21. WOOD N/A 2
22. PLASTIC HUIS
PIPES
N/A 4
The associated pictures related to the hardware
components are given below:-
1. ARDUINO MEGA 2560
2. SERVO MOTOR SG90
3. SERVO MOTOR 14K TORQUE

4. SERVO MOTOR 10K TORQUE
5. BREAD BOARD
6. JUMPER WIRE
7. FLEX SENSOR
8. 11.1V BATTERY
9. BATTERY CONNECTOR

10. POWER IC
9.POTENTIOMETER (10K,100K)
9. 22K RESISTORS
10. SPRING
11. STRING
12. PCB
IV. IMPLEMENTATION AND
CONSTRUCTION
A. HARDWARE PROCEDURE
1.Set up the Sensor Circuit

The flex sensors require a circuit in order for
them to be compatible with Arduino. It's a
voltage divider: the flex sensors are variable
resistors, and when paired with resistors of a
static value, change in resistance (in this case
bending the sensor) can be sensed through the
change in voltage between the resistors. This
can be measured by the Arduino through its
analog inputs. The schematic is attached (red
is positive voltage, black is negative, and blue
goes to the Arduino). The resistors in the
photo are 22K. I color-coded the wires we
used in the same way as the schematic, so we
can see more easily.
The main GND wire, which is connected to all
the individual GND wires from the sensors,
gets plugged into the Arduino's GND. The
+5V from the Arduino goes to the main
positive voltage wire, and each blue wire gets
plugged into a separate analog input pin.
Then we soldered the circuit onto a small PCB.One
that could be easily mounted onto the glove.
We were able to solder the wires to the sensors
relatively easily also, and used heat shrink to make
sure there were no shorts.
We then wrapped the area where the wires are
connected to the sensors with electrical tape to
stabilize the sensors.

Near the bottom, where the leads are attached, the
sensors are a bit weaker and the tape ensures that
they won't bend too far and won't get damaged.
3. FLEX SENSOR MOUNTING
Now it's time to mount the sensors and their
circuit onto the glove itself. First, We drilled a
tiny hole in the plastic of the sensors (at the
top, once the resistive material has ended). Be
sure not to hit the resistive material! Then, put
on the glove and pull it tightly to your hand.
On each finger, with a pencil or pen, make
small lines over the tops of each joint/knuckle.
This will tell you where to sew the sensors.
Sew each sensor tip to the area of each finger
just above where each of your fingernails
would be (use the hole you just drilled). Then,
for each sensor, make loose loops around them
with thread at both joints in each finger. Once
each sensor is in place and slides under the
loops of thread nicely.
Then We sewed the PCB onto the wrist part of the
glove tightly.
REMEMBER: for each step in this process, be sure
We're not sewing the glove itself closed. That's
quite a hassle.
4. HAND AND SERVO BED
CONSTRUCTION
1. FINGERS ASSEMBLY

We used plastic hollow pipes to construst the finger
parts.When assembling the fingers, we made sure
that the parts were oriented correctly before gluing.
Also, we made make sure to re-drill the holes on
the finger parts so the 3mm screws will act as hinge
pins without causing friction.Then we connected
the part using a string and screws.
Then we kept the screws in with a dab of hot glue
on the outside of the fingers.
2. SERVO BED CONSTRUCTION AND
SERVO MOUNTING:-
We have used a wooden piece to make the servo
bed. Here in the bed we made 5 servo motors to be
held perfectly within the bed. It’s just kind of a bed
for the servos. Later we have to put the strings to
connect the servos with each other. Here is the
construction figure shown below:-
Here is the picture of our wooden aervo bed shown
below:-

We waited before installing the strings into the
hand as we wanted to make sure the servos are
working first.
3. ADDING THE STRINGS:
Adding the strings is by far the hardest and most
tedious part of this project. It's simple in concept,
but difficult to actually execute. Threading the
fingers takes patience: remember that. The one
difference between my installation of the strings
and I used hot glue. To me, hot glue is more
adjustable when calibrating each finger because it
can be easily melted and re-hardened. We
connected the servo motor in a way we could move
our fingers with the exact comfort and flexilbity.
For that we calibrated the servo motors to connect
the strings with the exact process
To calibrate each servo ring so it flexes and relaxes
its finger when we wanted it to based on the input,
first we plugged in our Arduino and servo battery
and run the program. Then we put the glove on and
flex the finger that corresponds to the servo we’re
working on. We adjusted the servo ring so one hole
is closest possible to the fingers and pulled the
"relax" string of that finger as tightly as we can
without bending the finger. We put it through the
closest hole of the ring and glue it in place. Then,
straightened my finger and pulled and secured the
other string into the other hole. Then we repeated
this process with each finger. It's important to make
each string taut.
4. SETTING UP THE SERVO MOTOR
CIRCUIT:
1. SERVO MOTOR WIRING WITH
THE ARDUINO:
We connected the 5 servo motors (which had
been mounted on the servo-bed) and the
another servo (mounted on the hinge portion)
with the ARDUINO PWM pins. The PWM
input wire (orange) for each servo would be
attached to the Arduino pins as follows:
 Servo One - PWM -> Digital 9,
 Servo Two - PWM -> Digital 8,
 Servo Three - PWM -> Digital 7,
 Servo Four - PWM -> Digital 6,
 Servo Five - PWM -> Digital 5,
 Servo Six - PWM -> Digital 4,
Following is the diagram showing the
wiring of 6 servo motors with the Digital
(PWM) pins of ARDUINO:-

1. WIRING OF THE SIXTH (WRIST)
SERVO MOTOR:
The servo motor which we have mounted on the
wrist for it’s movement .Then it’s control(orange)
wire was first connected with the PWM pin 4.
Servo Six - PWM -> Digital 4
After that we connected its red and black (power)
wire of the servo with a small solder-less bread
board. We also connected a Potentiometer in series
with the power wires. We connected the positive
and the ground wire of the POT in series with the
power wires of the servo and connected the
variable resistive wire of the POT with an analog
pin of the ARDUINO.
5. THUMP CONSTRUCTION:
We used aluminium plate and a piece of
plastic glass for the thump construction. The
larger portion of t he wrist(Top surface) has
been constructed with aluminium plate and
has been threaded using threading machine.
The rest of the wrist has been constructed
using a plastic glass plate with which we
assembled the 5 fingers using super glue and
screws keeping the comfortable position of the
fingers in mind.
5. JOINING THE FINGERS WITH THE
THUMP:
We assembled the 5 fingers with the plastic
glass made portion of the wrist using super
glue and screws.
According to the following pictures we tried to
join all the fingers keeping comfort area and
the top and bottom view of the fingers in
mind.
5.BREAD BOARD DETAIL:
We used a bread board here to construct a
particular circuit for the operation of 16 k torque
servo motor for the control over the total hinge of
the hand.
V. FUCTIONAL TESTING
A. SOFTWARE
IMPLEMENTATION
1. SOFTWARE DOWNLOAD:
Following the instructions on the
Getting Started section of the Arduino
web site,
http://arduino.cc/en/Guide/HomePage.
we at first downloaded the latest

version of Arduino, arduino-1.0.5-
windows.
2. SOFTWARE INSTALLATION:
Going all the way through the steps to
where we saw the pin 13 LED blinking.
This is the indication that we had all
software and drivers successfully installed
and could start exploring with our own
programs.
3. SOFTWARE EXECUTION:
1.Connected our Arduino to the computer
with the USB cable. We did not need the
battery for that time.
The green PWR LED will light. If there was
already a program burned into the Arduino, it
will
run.
2.Started the Arduino development
environment. In Arduino-speak, programs are
called “sketches”,
but here we will just call them programs.
Our window would look something like this:-
3.Then we clicked the Upload button or Ctrl-U
to compile the program and load on the
Arduino board.
B. POWER ISSUE:
1. CONNETCING A BATTERY:
1.For stand-alone operation, the board is
powered by a battery rather than through the
USB connection to the computer. While the
external power can be anywhere in the range
of 6 to 24 V
(We used here a 11.1V Lithium ion battery), a
standard 9 V battery is convenient.
2.We then stablished Vin and Gnd connections
on the board, it is better to solder the battery
snap leads to a DC power plug and connect to
the power jack on the board.
N.B Watch the polarity as you connect your battery
to the snap as reverse orientation could blow out
your board.
3. Then we disconnected our Arduino from the
computer. Then we connected a 11.1 V battery to
the Arduino power jack using the battery snap
adapter confirming that the blinking program
runs. This showed that we could power the Arduino
from a battery and that the program we download
ed runs without needing a connection to the host
PC.
2. SETTING UP THE VOLTAGE OF POWER
IC:

Battery power input is 11.1V. This input is
supplied to 2 power ICs. Through power ICs we
have controlled the input voltage to get the desired
output of 7V & 3V. As the threshold voltage of
arduino is 7V and the threshold voltage of servo is
3V.One power IC is set to get output of 7V. The
output terminal of that power IC is connected to
Vin and Gnd pin of arduino. As the threshold
voltage of servo motor is 3V.Here the power
adjustment of the power IC is done by keeping the
multimeter positive and negative terminals into the
input side of the power IC, IN+ & IN- and we
varied the voltage with the help of power IC
voltage-variable nob. Another power IC is set to
get output of 3V. The output terminal of that power
IC is connected to PCB and 6 terminals are made
short with that so that 6 motors can get power
supply.
Here the voltage adjustment diagram of power IC
is given below.
4. CALIBRATING THE FLEX
SENSORS:
The sensor is simply a variable resistor that
changes its resistance in response to how much it is
bent. The way that the device works is based on its
construction. The sensor has a backplane of a thin
plastic polymer that can easily bend.
The bend sensor consists of a coated substrate, such
as plastic, that changes in electrical conductivity as
it is bent. This provides non-mechanical reliability
in electronic sensing and actuator technology.On
top of this polymer is a layer of carbon that forms a
resistor (which connects between the two metal
terminals on the left side).On top of the carbon are
equally sized and spaced squares of metal which
are glued in place at their centers to the backplane.
When the device is bent the spaces between the
metal plates grows larger and thus the amount of
carbon resistor shorted out by each metal square is
reduced. When that happens the resistance of the
sensor goes up. The response of the sensor is very
linear over its flexible range. The sensor can only
reliably indicate bending in one direction (into the
page as it is pictured here).

For calibrating the sensors, we used the sensor
with ARDUINO MEGA we fed the +5volt D.C as
we had a lot of problems getting reliable readings
from the sensor at first.. power supply voltage from
ARDUINO into one side of the sensor and then
measured the voltage on the other side of the sensor
using the yellow "analog in" jack on ARDUINO.
Since the device is simply a variable resistor the
voltage drop across the resistor changes with the
amount of bend the sensor undergoes.To calibrate
the sensor we simply created "our own sensor"
profile under ARDUINO programming software
and used the on screen volt meter to create a two
point calibration at zero and at 50% (90 degrees) of
bend.
5. TESTING THE SERVOS:
At this point, the servos should already be mounted
into the forearm. To connect them to the power
supply and Arduino, We used a small solder-less
breadboard. Connected each positive wire of the
servo (usually red) to one of the rails on the
breadboard, and the negative side of them (usually
black or brown) to another rail. I should be
remembered to connect the negative rail on the
breadboard to the Arduino's other GND: all the
GNDs in a circuit need to be connected for it to
work. The +VCC can be different, but the GNDs
need to be the same.
Then we uploaded the program to the Arduino (the
file is attached) and made sure of all the
connections to the glove and servos are correct. Put
on the glove, and turned on the Arduino. The
servos should rotate based on how much our
fingers are bent. If this is the case, it's working! If
you're more experienced with Arduino and know
how to test the input values of your particular
sensors, you can adjust the range in the program so
it works best for you. I assume all the sensors are
practically identical,.If the servos aren't working
properly, make sure all the connections are correct .
6. FINAL STEP : WIRING OF THE
TOTAL CIRCUIT WITH
EXECUTION
After completing all the steps mentioned above we
assembled all the stationary circuits together to
build tha main circuit for execution.The main
circuit diagram is given below:-
The final step is to upload the Arduino sketch to
our board. As soon as the Arduino resets, the hand
should start its calibration routine by moving each
servo through its range of motion.
First after uploading the program to the Arduino
and making sure all the connections to the glove
and servos are correct we put on the glove and have
plugged in the Arduino and servo battery and run
the program. Putting the glove on and flex the
finger that corresponded to the servo we were
working on. Then we adjusted the servo ring. The
servos rotated basing on how much fingers were
bent. So the program started working.
C. MILESTONE CHART
Research Sensor Options
Completed
Research Servo Options Completed
Order Parts As Needed Completed
Setup ARDUINO Completed
Configure Power IC Completed

Interface
Interface With Servo
Motors
Completed
Interface With Flex
Sensor
Completed
Construction Of Hand Completed
Assembling The Hand Completed
Mounting the Servos Completed
Mounting the Flex Sensors Completed
Calibrating The Flex
Sensors
Completed
Write ARDUINO Sketch Completed
Testing The Completed
Code
Completed
Trouble-shooting Completed
VI. TROUBLE SHOOTING
A. GENERAL SAFETY RULES :
1. As with any machine with moving parts, be
careful not to let body parts get pinched. While the
hand has very little gaps and it may be difficult to
get trapped in them, it could potentially catch on
clothing, rings, etc.
2. When operating this hand apply a maximum of
5 VDC to the micro servos. Anything above this
voltage will destroy the small servos and will void
the warranty.
3. When working on the hand make sure all power
to the servos is turned off.
4. When the hand is at rest and not performing all
power should be turned off.
5. While this hand has compliance (mechanical
“give”) built into all fingers, it is still possible to
cause bodily and collateral damage with this hand
if it’s attached to a mechanism that is not carefully
controlled.
6. If excessive force is applied to any finger or
thumb for picking up heavy objects it may destroy
the servos or can destroy any mechanism.
7.Our animatronic hand is equipped with SG 90
Micro Servos. At any point in this hand’s lifespan:
 DO NOT Exceed 5 volts DC (VDC)
to the servos. The power IC is fixed to
be adjusted to a 3V max volt battery
supply,which is ideal to ensure this
voltage is never exceeded.
 DO NOT apply excessive force to the
fingers / thumb. This is multiplied by
the time it translates to torque on the
servo horn. This will cause damage,
typically resulting in “stripped” gears
but can also damage the internal servo
electronics.
 DO NOT get this hand wet. The
mechanisms contain steel hardware
which will rust if not cared for. The
servos are not water-resistant either.
8.All IN+ and IN- pins of the Power IC have to be
connected to the corresponding power supply pins.
B. COMPLIANCE ADJUSTMENT:
1. Each finger (including the thumb) is equipped
with a spring.
These systems can be adjusted to compress springs
more or less in each finger.
Less compression in the springs = more compliance
in the finger
If the springs are not adjusted equally per finger
this will shift the neutral position of the finger
(which can be beneficial at times)
2.When programming the hand in whichever servo
controller / microcontroller system you choose:
 Be very careful to define limits on each
finger / thumb. The new hand has shipped
with all servos at a “0” position (roughly
translating to 1500 ms). At this position
we have installed and tuned the finger /
thumb mechanisms to be at a relative “0”
position. This means that as you power up
the hand for the first time and without
inputting any position commands other
than “0” or “neutral” the hand will move
very close to the neautral position .
3.To find the end limits for each finger / thumb:
Because of the infinite position possibilities you
have when adjust this hand’s compliance, it is
impossible for to predict – for each system – what
those limits will be on the control system. You will
have to set these yourself.
 To set the end limits first unplug ALL
servos except the servo you are now
tuning.
 Using this servos address on your control
system carefully move the servo using
whichever commands are applicable to the
ARDUINO. Move this servo in small
increments and LISTEN. When you hear
the servo slightly “hum” and do not see
any more motion in the finger / thumb in
the direction you are traveling BACK

THE SERVO DOWN immediately.
Leaving it at this point will damage the
servo. By backing the servo down
(changing the value to slightly closer to
your neautral position value) you will
extend the life of that servo and battery
system powering the hand (stalled servos
pull more amps than servos with a near-
zero load).
4.Repeat the above for the opposite direction of
that finger / thumb.
5.Repeat this process above for each finger.
C. RISKS AND INTERFACED
ISSUES ENCOUNTERED WITH
THE HARD WARES
1. BREAD BOARD BURNT OUT
Many small test circuits had to be built on
breadboards and tested in the project, under actual
circumstances, to make sure they would not fry.
 CAUSE: Several components were not
grounded and did in fact fry. A breadboard
was also melted.
 TROUBLE SHOOT: The circuit
components must have to be
grounded properly when needed.
2. FLEX SENSOR READING
PROBLEMS
 CAUSE: This problem maybe caused due
to the wrong design of our analog circuit.
 TROUBLE SHOOT :
1.We connected in series: a 5 Vdc supply,
the flex sensor, 22K resistor and ground.
(That is, the end of the resistor that is not
connected to the sensor gets connected to
the ground of the 5Vdc power supply.)
2.Then we connected a voltmeter between
that same ground and the connection
between the sensor and the resistor.
Measured the voltage with various
amounts of flexing. That should tell you
what the analog input (AI) pin of your
Arduino will see. Once we had that circuit
giving us reasonable results, we went
back for getting the Arduino to read that
for us.
3. FINGERS WERE NOT MOVING
PROPERLY
 CAUSE: While it was not moving, a noise
from the servo was a steady “whirring”
sound. May be we have applied too much
force to the servo and stripped the internal
gears.
 TROUBLE SHOOT :
1. We reset the Arduino as we were using
one power source. Then Checked our
power supply. Checked whether it was
connected or not, Then checked whether
it supplying at least 3.5 volts that
minimum servo controller’s recommended
voltage or not.
2.Double checked our servo controller.
Checked whether it was receiving /
sending signals appropriately or not. Then
we tried plugging a loose, new servo into
the same port to test..
3.Inside the micro servo the motor is
grinding plastic against plastic. After the
proper testing we considered it as the main
reason behind the problem we
encountered . That’s why we tried SG90
sevos of metallic gear instead.
4.Slight adjustments in the servo
mounting holes may be necessary. This
modification would void the warranty but
may help your particular situation.
4. HAND/ WRIST FALLING OFF
 CAUSE : Lower clutch mechanism can't
be sufficiently tightened to raise the arm.
 TROUBLE SHOOT
1. As this occurred at the beginning stage,
I meant at the first try after
assembly, we moved the corresponding
motor and checked whether the
gears were correctly engaged or not. As
they were engaged properly we moved to
the second trouble shooting process.
2. We checked whether the tapping
screws were being installed on the wrist
properly or not. If they were, then it has
been possible the uppermost
screw of the base side being not tightened
enough. So, we tightened that
appropriately and thus succeeded to
trouble shoot.

5. SERVOS MOVING ERRATICALLY
 CAUSES WITH TROUBLE
SHOOTING:
As with any animatronic project, many times this
will come down to a complex system interaction
between our microcontroller / pc and the servo
controller. Usually the servos are just fine. Here are
some things that have been found with testing
done on multiple PC’s and servo controllers:-
 CAUSE-1 : Mechanisms may have been
subject to dirt or adverse conditions. This
can be confirmed by disconnecting the
mechanism from the servo.
 TROUBLE SHOOT:
We disconnected the mechanism from
the servo then again connected the
mechanism. If there were still issues the
hand would have to be carefully
disassembled, cleaned, re-assembled and
tuned as above.
But it didn’t work either.
 CAUSE-2: The of cause of this can be
almost always a “noisy” power supply.
Even though we may had carefully
selected an AC to DC 5VDC output
supply that can handle 1 A pull, it may
not be producing a quiet voltage.
 TROUBLE SHOOT:
1.Any control system can be riddled with
connection issues. Servos are usually the
most trouble-free devices in the entire
loop.,So. We backtracked into our servo
controller settings (rate mis-match, etc),
cable connections, ARDUINO
interference, and our code.
2.As the above did not solve the issue,we
tried plugging in a simple battery supply
of about 11.1 VDC and then converted the
voltage of the supply into 3VDC which is
the threshold voltage of the servo by
adjusting the voltage of a power IC. In all
cases this has corrected this issue in our
testing.
 CAUSE-3:. If your powering the servos
with a different power source than the
Arduino, they need to share the same
ground or the PWM signals will corrupt
between the Arduino and servos. Fingers /
thumb are moving but erratically.
 TROUBLE SHOOT: We checked all
our ground connections properly as the
above trouble shooting process couldn’t
resist the servos form moving erratically
in total . After that we reconnected those
thus we managed to solve this problem
finally.
6. SERVOS MOVING SLOWLY WHEN IT
SHOULD BE STOPPED
 CAUSE: This was a result of our servos
not being calibrated quite right.
 TROUBLE SHOOT: To calibrate our
servos we had to wait until our program
had the servos stopped . Then with a
small screwdriver we tuned the
potentiometer inside the servo (the little
opening in the servo casing just above
where the wires are). Then rotated that
either left or right until the servo was truly
stopped.
7. SERVOS BEING SO NOISY
 CAUSES WITH TROUBLE
SHOOTING :
The word servo refers solely to a device
that uses negative feedback for control.
One major drawback to working with
servos is the large amounts of electrical
noise they produce.This noise can
interfere with your sensors and can even
impair your microcontroller by causing
voltage dips on your regulated power line.
Large enough voltage dips can corrupt the
data in microcontroller registers or cause
the microcontroller to reset.
 CAUSE-1: cheap brushed motors can be
noisy. Cheap hobby grade servos can
sometimes chatter if they do not settle in a
stable state. This is normal and is caused by
poor tuning, a lack of a dead band, and
backlash between the motor and the encoder
(potentiometer).
 TROUBLE SHOOT:
1.We can get very quiet systems if you are
willing to pay for it.
2. Keeping our motor and power leads
as short as possible, we can decrease
noise by twisting the motor leads so they
spiral around each other.

 CAUSE-2: The main source of motor noise is
the commutator brushes, which can bounce as
the motor shaft rotates. This bouncing, when
coupled with the inductance of the motor
coils and motor leads, can lead to a lot of
noise on your power line and can even induce
noise in nearby lines.
 TROUBLE SHOOT : We didn’t go for
the trouble shooting of this as we found
the circuit to be more complicated to be
executed properly. That’s why we bought
the new SG90 motors with metalic gears
and thus tried to troubleshoot this
problem.
The further discussion about this Trouble
shooting process will be written on the
ASSUMPTIONS AND LIMITATIONS
portion of this report.
D. INTERFACED ISSUES
ENCOUNTERED WITH THE
SOFTWARE
1.COMMON CODING ERRORS:
 Forgetting the semi-colon at the end of a
statement
 Misspelling a command
 Omitting opening or closing braces
 Thus If there is a syntax error in the
program caused by a mistake in typing, an
error message will appear in the bottom of
the program window.
 THOUBLE SHOOTING:
Generally, staring at the error will reveal
the problem. If we continue to have
problems,
we should try these ideas:
 Running the Arduino program again.
 Checking that the USB cable is secure at
both ends.
 Rebooting our PC because sometimes the
serial port can lock up. If a “Serial
port…already in use” error appears when
uploading.
2. ERRORS ABOUT UNDECLARED
FUNCTIONS OR UNDECLARED
TYPES:
 CAUSE : The Arduino environment
attempts to automatically generate
prototypes for our functions, so that we
can order them as we like in our sketch.
This process, however, isn't perfect, and
sometimes leads to obscure error
messages.
If we declare a custom type in our code
and create a function that accepts or
returns a value of that type, we'll get an
error when we try to compile the sketch.
This is because the automatically-
generated prototype for that function will
appear above the type definition.
 TROUBLE SHOOT: If we declared a
function with a two-word return type (e.g.
"unsigned int") the environment would
not realize it's a function and would not
create a prototype for it. That meant we
needed to provide our own, or place the
definition of the function above any calls
to it.
VII. ASSUMPTIONS AND
LIMITATIONS
A. USING OF FLEX SENSORS IS
NOT COST EFFECTIVE
LIMITATION :
Flex sensors are so much costly. It took a huge
amount of money to be spent on the
implementation of this process. It’s one of
the main limitations of this project.
We could have used some other process to
make the sensors by ourselves, But
thinking of the time limit of the academic
submission of this project and also for the
perfection of the execution of this project
we used the costly Flex sensors.
ASSUMPTION:
We could have used the Neopren Bend
Sensors in place of the flex sensors for the
movement of the fingers of the
animatronic hand.
It would be of so much cost-effective but
time-consuming.
This bend sensor actually reacts (decreases
in resistance) to pressure, not specifically
to bend. But because it is sandwiched

between two layers of neoprene (rather
sturdy fabric), pressure is exerted while
bending, thus allowing one to measure
bend (angle) via pressure. It is sensitive
enough to register even slight bend and has
a large enough range to still get
information when the limbs are fully bent.
The neoprene is great for isolating the
conductive thread stitches and keeps the
sensor from wrinkling even when
repeatedly being bend.
The resistance range of this bend sensor depends a
lot on the initial pressure. Ideally you have above
2M ohm resistance between both contacts when the
sensor is lying flat and unattached. But this can
vary, depending on how the sensor is sewn and
how big the overlap of the adjacent conductive
surfaces are. Sewing the contacts can be done as
diagonal stitches of conductive thread – to
minimize the overlap of conductive surface. But
only the slightest bend or touch of the finger will
generally bring the resistance down to a few Kilo
ohm and, when fully pressured, it goes down to
about 200 ohm. The sensor still detects a
difference, right down to about as hard as you can
press with your fingers. The range is non-linear and
gets smaller as the resistance decreases.
B. USING OF UNNECESSARY FLEX
SENSORS
LIMITATION :
We used five flex sensors for the movement of
the five fingers of our animatronic hand.
But due to some unavoidable circumstances
one of the flex sensors has losen it’s
sensitivity. For the reason we needed to buy
one more flex sensors. But as the flex sesnsors
are costly, we switched to the another plan. We
decided to connect the last two fingers with the
animatronic hand with the same flex sensor.
Thus the fourth flex sensor has been used to
move the two fingers at a time.
ASSUMPTION: As the fourth flex sensor has
been used to move the two fingers at a time.
The other flex sensors could also be used for
the movement of the finger (more than one) at
a time. So, there were no need of buying
exactly the five flex sensor for the movement
of five fingers at a time. We assumed it
unnecessary.
C. COULDN’T DEAL WITH THE
MOTOR NOISE
LIMITATION : As we found the trouble
shooting circuit of motor noise a complex one
and also due to the time limit of the project
submission we couldn’t deal with the motor
noise. And we bought new motors to solve this
problem.
ASSUMPTION: For dealing with the motor
noise we assumed some of the measures which
we could have executed in case of having
some more duration of the project time-limit.
 SOLDERING CAPACITORS
ACROSS OUR MOTOR
TERMINALS.
Capacitors are usually the most effective way
to suppress motor noise, and as such we
recommend always solder at least one
capacitor across motor terminals. Typically we
will want to use anywhere 0.1uF capacitors,
soldered as close to the motor casing as
possible. For applications that require
bidirectional motor control, it is very important
that we do not use polarized capacitors!
 We can construct the following circuit if
the above measures cannot remove the
motor noise.

VIII. CONCLUSION:
We are glad that we chose to complete this
project on the Arduino. It was our first
real coding experience on this platform,
and we can say that compared to writing
C++, writing Wiring libraries for Arduino
makes for a much more fun and
Productive experience We are grateful
that our time on the C++ taught us a lot
about what is happening behind the
scenes, but quiet honestly it is nice to not
have to worry about it so much.
One thing we learned from this project is
that servos and flex sensors in positioning,
timing and environmental texture can lead
to all sorts of undesirable readings. We
were a bit disappointed with the
performance of the SG90 servos in this
particular use case, It required a lot of the
fine-tuning to get readings accurate as the
servo rotated.
As stated previously, another area I need to look
into is battery power. This project is a poor use
case for a 11.1V battery. A better long term
portable power supply would include a higher
efficiency in the output. That’s why we also used a
PC for the long term power supply.
Although the Animatronic hand did not operate
with no errors, it is a great success overall. The
Animatronic hand met all safety restrictions, easy
to operate and energy efficient. This types of
animatronic hand can be used for various puposes.
The Animatronic Hand can be implemented in all
the sectors where human interaction is needed,
like-Handling of the explosive objects, performing
various sophisticated operational jobs in the
medical sectors, Industrial manufacturing etc.
With more time and resources put for things like
motors and base design we can carry a much larger
payload and have a sturdier platform to carry
things in. Much of this project could be used or
improved upon by future EEE students.
IX. LESSON LEARNED
The risks were subject to like everyone else,
running the risk of not receiving all materials in
time. Also, the calibration of flex sensors and the
servos proved to be difficult. We also had to be
careful about the ARDUINO and its wiring. We
also needed to make diagrams so we did not
detach a bunch of wires and not know how to
rewire them. Due to the recent political affairs and
with the improper communication facilities,we also
ran the risk of not having enough man-power to
complete the project. This is why we needed to
start as early as possible. We had to work very hard
to complete this project in time! But in the end, the
challenge and learning experience were well worth
it.
X. TASKING AND SCHEDULING
1. Gathering the hard wares 1 week.
2. Construction of the hand and making the
glove ready 1 week.
3. Calibration of flex sensors and testing of
servos 1 week.
4. Arduino wiring and Arduino code 2
weeks.
5. Connecting the whole circuit with
trouble-shooting 1 week.
XI. BILL OF MATERIALS
COMPONENTS PRICE
1.ARDUINO
MEGA2560
1*2,000= 2,000T.K
2. SERVO SG90 5*500 =2,500T.K
3. SERVO 14K
TORQUE
1*1,200=1,200T.K
4.SERVO 10K
TORQUE
2*1000=2,000T.K
5. BREAD BOARD 1*180 =180T.K
5. JUMPER WIRE 3*150 = 450 T.K
6. BATTERY 1*1,800=1,800T.K
7. CHARGER 1*1,500=1,500 T.K
8. FLEX SENSOR 5*2,100=10,500T.K
9. BOSTER 2*250 =500T.K
10.POT 2*10 =20T.K

11.RESISTORS 5*2 =10 T.K
12.SPRING 10*5 =50 T.K
13.CHARGER
CONNECTING
CABLE
1*160=160 T.K
14.PCB 1*20=20 T.K
15.WOOD &
PLASTIC PIPES
100 T.K
TOTAL=22,990 T.K
XII. REFERENCE
[1] The Absolute Beginner's Guide to
Arduino
http://forefront.io/a/beginners-guide-to-
arduino
[2] Principles of Robotics
http://www.g9toengineering.com/resources/
robotics.htm
[3] Servo Motor | Servo Mechanism |
Theory and Working Principle
http://www.electrical4u.com/servo-motor-
servo-mechanism-theory-and-working-
principle/
[4] DC Servo Motors | Theory of DC Servo
Motor
http://www.electrical4u.com/dc-servo-
motors-theory-and-working-principle/
[5] Introduction to Servo Motors
http://mechatronics.mech.northwestern.edu
/design_ref/actuators/servo_motor_intro.ht
ml
[6] DIY Robotic Hand Controlled by a
Glove and Arduino
by dschurman
http://www.instructables.com/id/DIY-
Robotic-Hand-Controlled-by-a-Glove-and-
Arduino/
[7] Animatronics
http://en.wikipedia.org/wiki/Animatronics
[8] Simple Servo Bed for InMoov
http://www.thingiverse.com/thing:65274
[9] AniHand - Animatronic Hand
http://letsmakerobots.com/node/34639
[10] Calibrator: An Arduino library to
calibrate sensors hooked to analog inputs
http://julianvidal.com/blog/calibrator-an-
arduino-library-to-calibrate-sensors-
hooked-to-analog-inputs/
[11] Arduino - Begin.
http://arduino.cc/en/Serial/begin
[12] Arduino learning pdf
http://www.ele.uri.edu/courses/ele205/Ardui
no%20-%20Learning.pdf
[13] Arduino Microcontroller
Guide
http://www.me.umn.edu/courses/me2011/ar
duino/arduinoGuide.pdf
[14] Arduino functions
http://playground.arduino.cc/Code/Functio
n
[15] Structuring Your Code into Functional
Blocks
https://www.inkling.com/read/arduino-
cookbook-michael-margolis-2nd/chapter-
2/recipe-2-10
[16] Arduino programming Problem
solution
http://stackoverflow.com/questions/1297589
5/arduino-argument-of-type-void-
classname-does-not-match-void-whi

[17] Blink Without Delay
http://arduino.cc/en/Tutorial/BlinkWithout
Delay
[18] Operating Two Servos with the Arduino
http://www.robotoid.com/appnotes/arduin
o-operating-two-servos.html
[19] Servo Problems With Arduino
http://rcarduino.blogspot.com/2012/04/ser
vo-problems-with-arduino-part-1.html
[20] Problem with arduino servo
http://electronics.stackexchange.com/questi
ons/93746/problem-with-arduino-servo
[21] Arduino Servo control problem,
external servo power source
https://forum.sparkfun.com/viewtopic.php?
f=32&t=24263
[22] Problem with multi servos on Arduino
http://www.youtube.com/watch?v=iZFO_8h
H7QY
[23]Multiple servo control
http://www.instructables.com/id/Serial-
Servo-Controller-wAduino-Control-Up-To-
1/
[24]Flex sensor
http://mech207.engr.scu.edu/SensorPresent
ations/Jan%20-
%20Flex%20Sensor%20Combined.pdf
[25] Arduino map() method
http://stackoverflow.com/questions/9024124
/arduino-map-method-why
[26] Arduino programming tutorial
http://opensourcehardwaregroup.com/tutor
ial-09-reading-analog-pins-and-converting-
the-input-to-a-voltage/
[27] Calibration of flex sensors
http://www.mtbs3d.com/phpBB/viewtopic.p
hp?f=138&t=17799
[28] Sensing A Bend With A Flex Sensor +
Arduino
http://bildr.org/2012/11/flex-sensor-
arduino/
[29] Arduino tutorial PWM
http://www.youtube.com/watch?v=Y1QraI5
i_XM

Animatronic hand controller

More Related Content

What's hot (20)

Viewers also liked (20)

Similar to Animatronic hand controller (20)

More from Sabrina Chowdhury (20)

Recently uploaded (20)

Animatronic hand controller