101 200 transistorcircuits

save as: 101-200 Transistor circuits.pdf

Go to: 1 - 100 Transistor Circuits
Go to: 100 IC Circuits

86 CIRCUITS as of 28-5-2011

See TALKING ELECTRONICS WEBSITE
email Colin Mitchell: talking@tpg.com.au

INTRODUCTION
This is the second half of our Transistor Circuits e-book. It contains a
further 100 circuits, with many of them containing one or more Integrated
Circuits (ICs).
It's amazing what you can do with transistors but when Integrated Circuits
came along, the whole field of electronics exploded.
IC's can handle both analogue as well as digital signals but before their
arrival, nearly all circuits were analogue or very simple "digital" switching
circuits.
Let's explain what we mean.
The word analogue is a waveform or signal that is changing (increasing and
decreasing) at a constant or non constant rate. Examples are voice, music,
tones, sounds and frequencies. Equipment such as radios, TV's and
amplifiers process analogue signals.
Then digital came along.
Digital is similar to a switch turning something on and off.
The advantage of digital is two-fold.
Firstly it is a very reliable and accurate way to send a signal. The signal is
either HIGH or LOW (ON or OFF). It cannot be half-on or one quarter off.
And secondly, a circuit that is ON, consumes the least amount of energy in
the controlling device. In other words, a transistor that is fully turned ON
and driving a motor, dissipates the least amount of heat. If it is slightly
turned ON or nearly fully turned ON, it gets very hot.
And obviously a transistor that is not turned on at all will consume no
energy.
A transistor that turns ON fully and OFF fully is called a SWITCH.
When two transistors are cross-coupled in the form of a flip flop, any pulses
entering the circuit cause it to flip and flop and the output goes HIGH on
every second pulse. This means the circuit halves the input pulses and is
the basis of counting or dividing.
Digital circuits also introduce the concept of two inputs creating a HIGH
output when both are HIGH and variations of this.
This is called "logic" and introduces terms such as "Boolean algebra" and
"gates."
Integrated Circuits started with a few transistors in each "chip" and
increased to whole mini or micro computers in a single chip. These chips
are called Microcontrollers and a single chip with a few surrounding
components can be programmed to play games, monitor heart-rate and do
all sorts of amazing things. Because they can process information at high
speed, the end result can appear to have intelligence and this is where we
are heading: AI (Artificial Intelligence).

But let's crawl before we walk and come to understand how to interface
some of these chips to external components.
In this Transistor Circuits ebook, we have presented about 100 interesting
circuits using transistors and chips.
In most cases the IC will contain 10 - 100 transistors, cost less than the
individual components and take up much less board-space. They also save a
lot of circuit designing and quite often consume less current than discrete
components.
In all, they are a fantastic way to get something working with the least
componentry.
A list of of Integrated Circuits (Chips) is provided at the end of this book to
help you identify the pins and show you what is inside the chip.
Some of the circuits are available from Talking Electronics as a kit, but
others will have to be purchased as individual components from your local
electronics store. Electronics is such an enormous field that we cannot
provide kits for everything. But if you have a query about one of the
circuits, you can contact me.

Colin Mitchell
TALKING ELECTRONICS.

talking@tpg.com.au

To save space we have not provided lengthy explanations of how the
circuits work. This has already been covered in TALKING ELECTRONICS Basic
Electronics Course, and can be obtained on a CD for $10.00 (posted to
anywhere in the world) See Talking Electronics website for more details:
http://www.talkingelectronics.com

MORE INTRO
There are two ways to learn electronics.
One is to go to school and study theory for 4 years and come out with all
the theoretical knowledge in the world but almost no practical experience.
We know this type of person. We employed them (for a few weeks!). They
think everything they design WILL WORK because their university professor
said so.
The other way is to build circuit after circuit and get things to work. You
may not know the in-depth theory of how it works but trial and error gets
you there.
We know. We employed this type of person for up to 12 years.
I am not saying one is better than the other but most electronics
enthusiasts are not "book worms" and anyone can succeed in this field by
constantly applying themselves with "constructing projects." You actually
learn 10 times faster by applying yourself and we have had technicians
repairing equipment after only a few weeks on the job.
It would be nothing for an enthusiast to build 30 - 40 circuits from our
previous Transistor eBook and a similar number from this book. Many of the
circuits are completely different to each other and all have a building block
or two that you can learn from.
Electronics enthusiasts have an uncanny understanding of how a circuit
works and if you have this ability, don't let it go to waste.
Electronics will provide you a comfortable living for the rest of your life
and I mean this quite seriously. The market is very narrow but new designs
are coming along all the time and new devices are constantly being
invented and more are always needed.
Once you get past this eBook of "Chips and Transistors" you will want to
investigate microcontrollers and this is when your options will explode.
You will be able to carry out tasks you never thought possible, with a chip
as small as 8 pins and a few hundred lines of code.
As I say in my speeches. What is the difference between a "transistor man"
and a "programmer?" TWO WEEKS!
In two weeks you can start to understand the programming code for a
microcontroller and perform simple tasks such as flashing a LED and
produce sounds and outputs via the press of a button.
All these things are covered on Talking Electronics website and you don't
have to buy any books or publications. Everything is available on the web
and it is instantly accessible. That's the beauty of the web.
Don't think things are greener on the other side of the fence, by buying a
text book. They aren't. Everything you need is on the web AT NO COST.
The only thing you have to do is build things. If you have any technical
problem at all, simply email Colin Mitchell and any question will be
answered. Nothing could be simpler and this way we guarantee you
SUCCESS. Hundreds of readers have already emailed and after 5 or more
emails, their circuit works. That's the way we work. One thing at a time
and eventually the fault is found.
If you think a circuit will work the first time it is turned on, you are fooling
yourself.
All circuits need corrections and improvements and that's what makes a
good electronics person. Don't give up. How do you think all the circuits in
these eBooks were designed? Some were copied and some were designed
from scratch but all had to be built and adjusted slightly to make sure they

worked perfectly.
I don't care if you use bread-board, copper strips, matrix board or solder
the components in the air as a "bird's nest." You only learn when the circuit
gets turned on and WORKS!
In fact the rougher you build something, the more you will guarantee it will
work when built on a printed circuit board.
However, high-frequency circuits (such as 100MHz FM Bugs) do not like
open layouts and you have to keep the construction as tight as possible to
get them to operate reliably.
In most other cases, the layout is not critical.

TRANSISTORS
Most of the transistors used in our circuits are BC 547 and BC 557. These
are classified as "universal" or "common" NPN and PNP types with a voltage
rating of about 25v, 100mA collector current and a gain of about 100. Some
magazines use the term "TUP" (for Transistor Universal PNP) or "TUN" (for
Transistor Universal NPN). We simply use Philips types that everyone
recognises. You can use almost any type of transistor to replace them and
here is a list of the equivalents and pinouts:

CONTENTS red indicates 1-100 Transistor Circuits
Adjustable High Current Power Supply Mains Night Light
Aerial Amplifier Make any capacitor value
Alarm Using 4 buttons Make any resistor value
Audio Amplifier (mini) Metal Detector
Automatic Battery Charger Model Railway time
Battery Charger - 12v Automatic NiCd Charger
Battery Charger - Gell Cell Phase-Shift Oscillator - good design
Battery Charger MkII - 12v trickle charger Phone Bug
Battery Monitor MkI Phone Tape-3
Battery Monitor MkII Phone Tape-4 - using FETs
Bike Turning Signal PIC Programmer Circuits 1,2 3
Beacon (Warning Beacon 12v) Powering a LED
Beeper Bug Power ON
Blocking Oscillator Power Supplies - Fixed
Book Light Power Supplies - Adjustable LMxx series
Buck Regulator 12v to 5v Power Supplies - Adjustable 78xx series
Camera Activator Power Supplies - Adjustable from 0v
Capacitor Discharge Unit MkII (CDU2) Trains Power Supply - Inductively Coupled
Capacitor Discharge Unit MkII - Modification Push-ON Push-OFF
Car Detector (loop Detector) PWM Controller
Car Light Alert Quiz Timer
Charger Gell Cell Railway time
Charger - NiCd Random Blinking LEDs
Chip Programmer (PIC) Circuits 1,2 3 Rectifying a Voltage
Circuit Symbols Complete list of Symbols Resistor Colour Code
Clap Switch Resistor Colour Code - 4, 5 and 6 Bands
Code Lock Reversing a Motor & 2 & 3
Colour Code for Resistors - all resistors Sequencer
Constant Current Shake Tic Tac LED Torch
Constant Current Drives two 3-watt LEDs Simple Flasher
Crystal Tester Simple Touch-ON Touch-OFF Switch
Dark Detector with beep Alarm Siren
Darlington Transistor Soft Start power supply
Decaying Flasher Super-Alpha Pair (Darlington Transistor)
Delay Turn-off - turns off a circuit after a delay Sziklai transistor
Driving a LED Telephone amplifier
Fading LED Telephone Bug
Flasher (simple) 3 more in 1-100 circuits Touch-ON Touch-OFF Switch
Flashing Beacon (12v Warning Beacon) Tracking Transmitter
Fluorescent Inverter for 12v supply Track Polarity - model railway
FM Transmitters - 11 circuits Train Detectors
Gell Cell Charger Transformerless Power Supply
Hex Bug Transistor tester - Combo-2
H-Bridge Vehicle Detector loop Detector
High Current from old cells VHF Aerial Amplifier
High Current Power Supply Voltage Doubler
Increasing the output current Voltage Multipliers
Inductively Coupled Power Supply Voyager - FM Bug
Intercom Wailing Siren
Latching A Push Button Water Level Detector
Latching Relay XtalTester
LED Detects light Zapper - 160v
LEDs on 240v 1-watt LED
LEDs Show Relay State 1.5 watt LED
Limit Switches 3-Phase Generator
Low fuel Indicator 5v from old cells - circuit 1
Low Mains Drop-out 5v from old cells - circuit 2
Low Voltage cut-out 5v Supply
Low Voltage Flasher 12v Battery Charger - Automatic
Mains Detector 12v Flashing Beacon (Warning Beacon)
12v Supply

12v to 5v Buck Converter
20 LEDs on 12v supply
240v Detector
240v - LEDs

RESISTOR COLOUR CODE

See resistors from 0.22ohm to 22M in full colour at end of book and another resistor table

RECTIFYING a Voltage
These circuits show how to change an oscillating voltage (commonly called AC) to
DC. The term AC means Alternating Current but it really means Alternating Voltage
as the rising and falling voltage produces an increasing and decreasing current.
The term DC means Direct Current but it actually means Direct or unchanging
Voltage.
The output of the following circuits will not be pure DC (like that from a battery) but
will contain ripple. Ripple is reduced by adding a capacitor (electrolytic) to the output.

DARK DETECTOR with beep-beep-beep Alarm
This circuit detects darkness and produces a beep-beep-beep alarm. The
first two transistors form a high-gain amplifier with feedback via the 4u7 to
produce a low-frequency oscillator. This provides voltage for the second
oscillator (across the 1k resistor) to drive a speaker.

3-PHASE SINEWAVE GENERATOR
This circuit produces a sinewave and each phase can be tapped at
the point shown.

TRANSFORMERLESS POWER SUPPLY
This clever design uses 4 diodes in a bridge to produce a fixed
voltage power supply capable of supplying 35mA.
All diodes (every type of diode) are zener diodes. They all
break down at a particular voltage. The fact is, a power diode
breaks down at 100v or 400v and its zener characteristic is not
useful.
But if we put 2 zener diodes in a bridge with two ordinary power
diodes, the bridge will break-down at the voltage of the zener.
This is what we have done. If we use 18v zeners, the output will
be 17v4.
When the incoming voltage is positive at the top, the left zener
provides 18v limit (and the left power-diode produces a drop of
0.6v). This allows the right zener to pass current just like a normal diode but the voltage available to it is just 18v. The
output of the right zener is 17v4. The same with the other half-cycle.
The current is limited by the value of the X2 capacitor and this is 7mA for each 100n when in full-wave (as per this
circuit). We have 10 x 100n = 1u capacitance. Theoretically the circuit will supply 70mA but we found it will only deliver
35mA before the output drops. The capacitor should comply with X1 or X2 class. The 10R is a safety-fuse resistor.
The problem with this power supply is the "live" nature of the negative rail. When the power supply is connected as
shown, the negative rail is 0.7v above neutral. If the mains is reversed, the negative rail is 340v (peak) above neutral
and this will kill you as the current will flow through the diode and be lethal. You need to touch the negative rail (or the
positive rail) and any earthed device such as a toaster to get killed. The only solution is the project being powered must
be totally enclosed in a box with no outputs.

LEDs on
240v
I do not like any circuit
connected directly to 240v
mains. However Christmas
tress lights have been
connected directly to the
mains for 30 years without
any major problems.
Insulation must be
provided and the lights
(LEDs) must be away from
prying fingers.
You need at least 50 LEDs
in each string to prevent
them being damaged via a surge through the 1k resistor - if the circuit is turned on at the peak of the waveform. As
you add more LEDs to each string, the current will drop a very small amount until eventually, when you have 90
LEDs in each string, the current will be zero.
For 50 LEDs in each string, the total characteristic voltage will be 180v so that the peak voltage will be 330v - 180v
= 150v. Each LED will see less than 7mA peak during the half-cycle they are illuminated. The 1k resistor will drop
7v - since the RMS current is 7mA (7mA x 1,000 ohms = 7v). No rectifier diodes are needed. The LEDs are the
"rectifiers." Very clever. You must have LEDs in both directions to charge and discharge the capacitor. The
resistor is provided to take a heavy surge current through one of the strings of LEDs if the circuit is switched on
when the mains is at a peak.
This can be as high as 330mA if only 1 LED is used, so the value of this resistor must be adjusted if a small
number of LEDs are used. The LEDs above detect peak current.
A 100n cap will deliver 7mA RMS or 10mA peak in full wave or 3.5mA RMS (10mA peak for half a cycle) in
half-wave. (when only 1 LED is in each string).

The current-capability of a capacitor needs more explanation. In the diagram on the left we see a capacitor
feeding a full-wave power supply. This is exactly the same as the LEDs on 240v circuit above. Imagine the LOAD
resistor is removed. Two of the diodes will face down and two will face up. This is exactly the same as the LEDs
facing up and facing down in the circuit above. The only difference is the mid-point is joined. Since the voltage on
the mid-point of one string is the same as the voltage at the mid-point of the other string, the link can be removed
and the circuit will operate the same.
This means each 100n of capacitance will deliver 7mA RMS (10mA peak on each half-cycle).
In the half-wave supply, the capacitor delivers 3.5mA RMS (10mA peak on each half-cycle, but one half-cycle is
lost in the diode) for each 100n to the load, and during the other half-cycle the 10mA peak is lost in the diode that
discharges the capacitor.
You can use any LEDs and try to keep the total voltage-drop in each string equal. Each string is actually working
on DC. It's not constant DC but varying DC. In fact is it zero current for 1/2 cycle then nothing until the voltage rises
above the total characteristic voltage of all the LEDs, then a gradual increase in current over the remainder of the
cycle, then a gradual decrease to zero over the falling portion of the cycle, then nothing for 1/2 cycle. Because the
LEDs turn on and off, you may observe some flickering and that's why the two strings should be placed together.

BOOK LIGHT
This circuit keeps the globe
illuminated for a few seconds after
the switch is pressed.
There is one minor fault in the
circuit. The 10k should be
increased to 100k to increase the
"ON" time.
The photo shows the circuit built
with surface-mount components:

CAMERA ACTIVATOR
This circuit was designed for a customer who wanted to trigger a camera after a
short delay.
The output goes HIGH about 2 seconds after the switch is pressed. The LED turns
on for about 0.25 seconds.
The circuit will accept either active HIGH or LOW input and the switch can remain
pressed and it will not upset the operation of the circuit. The timing can be changed
by adjusting the 1M trim pot and/or altering the value of the 470k.

MAKE YOUR OWN:

The transformer consists of 50 turns
0.25mm wire connected to the pins.
The feedback winding is 20 turns
15 LEDs on Matrix board 0.095mm wire with "fly-leads."
1-WATT LED
This circuit drives 15 LEDs to produce the same brightness as a 1-watt LED. The circuit
consumes 750mW but the LEDs are driven with high-frequency, high-voltage spikes, and
become more-efficient and produce a brighter output that if driven by pure-DC.
The LEDs are connected in 3 strings of 5 LEDs. Each LED has a characteristic voltage of
3.2v to 3.6v making each chain between 16v and 18v. By selecting the LEDs we have
produced 3 chains of 17.5v Five LEDs (in a string) has been done to allow the circuit to be
powered by a 12v battery and allow the battery to be charged while the LEDs are
illuminating. If only 4 LEDs are in series, the characteristic voltage may be as low as 12.8v
and they may be over-driven when the battery is charging. (Even-up the characteristic
voltage across each chain by checking the total voltage across them with an 19v supply and
470R dropper resistor.) The transformer is shown above. It is wound on a 10mH choke with

the original winding removed. This circuit is called a "boost circuit." It is not designed to
drive a single 1-watt LED (a buck circuit is needed).
The LEDs in the circuit are 20,000mcd with a viewing angle of 30 degrees (many of the LED
specifications use "half angle." You have to test a LED to make sure of the angle). This
equates to approximately 4 lumens per LED. The 4-watt CREE LED claims 160 lumens (or
40 lumens per watt). Our design is between 50 - 60 lumens per watt and it is a much-
cheaper design.

1.5 WATT LED
The circuit below can be modified to drive up to 30
white LEDs.
The effectiveness of a LED array increases when
they are spread out slightly and this makes them
more efficient than a single 1 watt or 2 watt LED.
The two modifications to the circuit make the BC337
work harder and this is the limit of the inductor. The
current consumption is about 95mA.
The winding details for the transformer are shown
above.

30 LEDs on Matrix board

DRIVE 20 LEDs FROM 12v - approx 1watt circuit
This is another circuit that drives a number of LEDs or a single 1 watt LED. It is a "Buck Circuit"
and drives the LEDs in parallel. They should be graded so that the characteristic voltage-drop
across each of them is within 0.2v of all the other LEDs. The circuit will drive any number from 1 to
20 by changing the "sensor" resistor as shown on the circuit. The current consumption is about
95mA @ 12v and lower at 18v. The circuit can be put into dim mode by increasing the drive
resistor to 2k2. The UF4004 is an ultra fast 1N4004 - similar to a high-speed diode. You can use
2 x 1N4148 signal diodes.
The circuit will not drive two LEDs in series - it runs
out of voltage (and current) when the voltage
across the load is 7v. It oscillates at approx 200kHz.
Build both the 20 LED and 1 watt LED version and
compare the brightness and effectiveness.
The photo of the 1 watt LED on the left must be
heatsinked to prevent the LED overheating. The
photo on the circuit diagram shows the LED
mounted on a heatsink and the connecting wires.

A 1-watt demo board showing the complex step-up circuitry.
This is a Boost circuit to illuminate the LED and is completely different to our design. It has been
included to show the size of a 1 watt LED.
The reason for a Boost or Buck circuit to drive one or more LEDs is simple. The voltage across a
LED is called a "characteristic voltage" and comes as a natural feature of the LED. We cannot
alter it. To power the LED with exactly the correct amount of voltage (and current) you need a
supply that is EXACTLY the same as the characteristic voltage. This is very difficult to do and so a
resistor is normally added in series. But this resistor wastes a lot of energy. So, to keep the loses
to a minimum, we pulse the LED with bursts of energy at a higher voltage and the LED absorbs
them and produces light. With a Buck circuit, the transistor is turned on for a short period of time
and illuminated the LEDs. At the same time, some of the energy is passed to the inductor so that
the LEDs are not damaged. When the transistor is turned off, the energy from the inductor also
gives a pulse of energy to the LEDs. When this has been delivered, the cycle starts again.

POWER SUPPLIES - FIXED:

A simple power supply can be made with a component called a "3-
pin regulator or 3-terminal regulator" It will provide a very low ripple
output (about 4mV to 10mV provided electrolytics are on the input
and output.
The diagram above shows how to connect a regulator to create a
power supply. The 7805 regulators can handle 100mA, 500mA and
1 amp, and produce an output of 5v, as shown.
These regulators are called linear regulators and drop about 4v
across them - minimum. If the current flow is 1 amp, 4watts of heat
must be dissipated via a large heatsink. If the output is 5v and input
12v, 7volts will be dropped across the regulator and 7watts must
be dissipated.

POWER SUPPLIES - ADJUSTABLE:

The LM317 regulators are adjustable and produce an output from
1.25 to about 35v. The LM317T regulator will deliver up to 1.5amp.

POWER SUPPLIES - ADJUSTABLE using 7805:

The 7805 range of regulators are called "fixed regulators" but they
can be turned into adjustable regulators by "jacking-up" their output
voltage. For a 5v regulator, the output can be 5v to 30v.

POWER SUPPLIES - ADJUSTABLE from 0v:

The LM317 regulator is adjustable from 1.25 to about 35v. To make
the output 0v to 35v, two power diodes are placed as shown in the
circuit. Approx 0.6v is dropped across each diode and this is where
the 1.25v is "lost."

5v POWER SUPPLY
Using the the LM317 regulator to produce 5v supply
(5.04v):

CONSTANT CURRENT
This constant current circuit can be adjusted to any value from a

few milliamp to about 500mA - this is the limit of the BC337
transistor.
The circuit can also be called a current-limiting circuit and is ideal in
a bench power supply to prevent the circuit you are testing from
being damaged.
Approximately 4v is dropped across the regulator and 1.25v across
the current-limiting section, so the input voltage (supply) has to be
5.25v above the required output voltage. Suppose you want to
charge 4 Ni-Cad cells. Connect them to the output and adjust the
500R pot until the required charge-current is obtained.
The charger will now charge 1, 2, 3 or 4 cells at the same current.
But you must remember to turn off the charger before the cells are
fully charged as the circuit will not detect this and over-charge the
cells.
The LM 317 3-terminal regulator will need to be heatsinked.
This circuit is designed for the LM series of regulator as they have a
voltage differential of 1.25v between "adj" and "out" terminals.
7805 regulators can be used but the losses in the BC337 will be 4
times greater as the voltage across it will be 5v.

CONSTANT CURRENT DRIVES TWO 3WATT LEDs

This constant current circuit is designed to drive two 3-watt Luxeon
LEDs. The LEDs require 1,000mA (1Amp) and have a characteristic
voltage-drop across them of about 3.8v. Approximately 4v is
dropped across the LM317T regulator and 1.25v across the current-
limiting resistors, so the input voltage (supply) has to be 12.85v. A
12v battery generally delivers 12.6v.
The LM 317T 3-terminal regulator will need to be heatsinked.
This circuit is designed for the LM series of regulator as they have a
voltage differential of 1.25v between "adj" and "out" terminals.

5v FROM OLD CELLS - circuit 1
This circuit takes the place of a 78L05 3-terminal regulator. It produces a constant 5v @
100mA. You can use any old cells and get the last of their energy. Use an 8-cell holder. The
voltage from 8 old cells will be about 10v and the circuit will operate down to about 7.5v. The
regulation is very good at 10v, only dropping about 10mV for 100mA current flow (the 78L05
has 1mV drop). As the voltage drops, the output drops from 5v on no-load to 4.8v and 4.6v on
100mA current-flow. The pot can be adjusted to compensate for the voltage-drop. This type of
circuit is called a LINEAR REGULATOR and is not very efficient (about 50% in this case). See
circuit 2 below for BUCK REGULATOR circuit (about 85% efficient).

The regulator connected to a 12v battery
pack

The regulator connected to a 9v
battery

The battery snap plugs into the pins on
the 5v regulator board with the red lead
going to the negative output of the board
as the battery snap is now DELIVERING
voltage to the circuit you are powering.

A close-up of the regulator
module

5v FROM OLD CELLS - circuit 2
This circuit is a BUCK REGULATOR. It can take the place of a 78L05 3-terminal regulator, but
it is more efficient. It produces a constant 5v @ up to 200mA. You can use any old cells and
get the last of their energy. Use an 8-cell holder. The voltage from 8 old cells will be about 10v
and the circuit will operate down to about 7.5v. The regulation is very good at 10v, only

dropping 10mV for up to 200mA output.

INCREASING THE OUTPUT CURRENT
The output current of all 3-terminal regulators can be increased by
including a pass transistor. This transistor simply allows the current to flow
through the collector-emitter leads.
The output voltage is maintained by the 3-terminal regulator but the current
flows through the "pass transistor." This transistor is a power transistor and
must be adequately heatsinked.
Normally a 2N3055 or TIP3055 is used for this application as it will handle
up to 10 amps and creates a 10 amp power supply. The regulator can be
78L05 as all the current is delivered by the pass transistor.

SOFT START
The output voltage of a 3-terminal regulator can be designed to rise
slowly. This has very limited application as many circuits do not like
this.

TURN-OFF DELAY
These 4 circuits are all the same. They supply power to a project for a short
period of time. You can select either PNP or NPN transistors or Darlington
transistors. The output voltage gradually dies and this will will produce weird
effects with some projects.

LED DETECTS LIGHT
The LED in this circuit will detect light to turn on the oscillator. Ordinary red LEDs do not
work. But green LEDs, yellow LEDs and high-bright white LEDs and high-bright red LEDs
work very well.
The output voltage of the LED is up to 600mV when detecting very bright illumination.
When light is detected by the LED, its resistance decreases and a very small current
flows into the base of the first transistor. The transistor amplifies this current about 200
times and the resistance between collector and emitter decreases. The 330k resistor on
the collector is a current limiting resistor as the middle transistor only needs a very small
current for the circuit to oscillate. If the current is too high, the circuit will "freeze."
The piezo diaphragm does not contain any active components and relies on the circuit to
drive it to produce the tone. A different LED Detects Light circuit in eBook 1:
1 - 100 Transistor Circuits

TRAIN DETECTORS
In response to a reader who wanted to parallel
TRAIN DETECTORS, here is a diode OR-circuit.
The resistor values on each detector will need to
be adjusted (changed) according to the voltage of
the supply and the types of detector being used.
Any number of detectors can be added. See
Talking Electronics website for train circuits and
kits including Air Horn, Capacitor Discharge Unit
for operating point motors without overheating the
windings, Signals, Pedestrian Crossing Lights
and many more.

TRACK POLARITY
This circuit shows the polarity of a track via a 3-
legged LED. The LED is called dual colour (or
tri-colour) as it shows red in one direction and
green in the other (orange when both LEDs are
illuminated).

DECAYING FLASHER
In response to a reader who wanted a flashing LED
circuit that slowed down when a button was
released, the above circuit increases the flash rate
to a maximum and when the button is released, the
flash rate decreases to a minimum and halts.

SIMPLE FLASHER

This simple circuit flashes a globe at a rate
according to the value of the 180R and 2200u
electrolytic.

LATCHING RELAY
To reduce the current in battery operated equipment a relay called LATCHING RELAY can be
used. This is a relay that latches itself ON when it receives a pulse in one direction and unlatches
itself when it receives a pulse in the other direction.
The following diagram shows how the coil makes the magnet click in the two directions.

To operate this type of relay, the voltage must be reversed to unlatch it. The circuit above produces
a strong pulse to latch the relay ON and the input voltage must remain HIGH. The 220u gradually
charges and the current falls to a very low level. When the input voltage is removed, the circuit
produces a pulse in the opposite direction to unlatch the relay.

The pulse-latching circuit above can be
connected to a microcontroller via the
circuit at the left. The electrolytic can be
increased to 1,000u to cater for relays with
a low resistance.

If you want to latch an ordinary relay so it remains ON after a pulse, the circuits above can be used.
Power is needed all the time to keep the relay ON.

Latching Relays are expensive but a 5v Latching Relay is available
from: Excess Electronics for $1.00 as a surplus item. It has 2 coils
and requires the circuit at the left. A 5v Latching Relay can be use
on 12v as it is activated for a very short period of time.

A double-pole (ordinary) relay and transistor can be
connected to provide a toggle action.
The circuit comes on with the relay de-activated and the
contacts connected so that the 470u charges via the
3k3. Allow the 470u to charge. By pressing the button,
the BC547 will activate the relay and the contacts will
change so that the 3k3 is now keeping the transistor
ON.
The 470u will discharge via the 1k. After a few seconds
the electro will be discharged. If the press-button is now
pushed for a short period of time, the transistor will turn
off due to the electro being discharged.

A single-coil latching relay normally needs
a reverse-voltage to unlatch but the circuit
at the left provides forward and reverse
voltage by using 2 transistors in a very
clever H-design.
The pulse-ON and pulse-OFF can be
provided from two lines of the
microcontroller.

A normal relay can be activated by a short
tone and de-activated by a long tone as
shown via the circuit on the left. This
circuit can be found in "27MHz Links"
Page 2.

LATCHING A PUSH BUTTON - also called: PUSH-ON
PUSH-OFF
When the circuit is turned on, capacitor C1 charges via the two 470k
resistors. When the switch is pressed, the voltage on C1 is passed to
Q3 to turn it on. This turns on Q1 and the voltage developed across
R7 will keep Q1 turned on when the button is released.
Q2 is also turned on during this time and it discharges the capacitor.
When the switch is pressed again, the capacitor is in a discharged
state and this zero voltage will be passed to Q3 turn it off. This turns
off Q1 and Q2 and the capacitor begins to charge again to repeat the
cycle.

REVERSING A MOTOR-1
There are a number of ways to reverse a motor. The following diagrams show how to connect a
double-pole double throw relay or switch and a set of 4 push buttons. The two buttons must be
pushed at the same time or two double pole push-switches can be used.
See H-Bridge below for more ways to reverse a motor.

Adding limit switches:

The way the dpdt relay circuit (above) works is this:
The relay is powered by say 12v, via a MAIN SWITCH. When the relay is activated, the motor travels
in the forward direction and hits the "up limit" switch. The motor stops. When the MAIN SWITCH is
turned off, the relay is de-activated and reverses the motor until it reaches th e "down-limit" switch
and stops. The MAIN SWITCH must be used to send the motor to the "up limit" switch.

REVERSING A MOTOR-2
AUTOMATIC FORWARD-REVERSE
The following circuit allows a motor (such as a train) to travel in the
forward direction until it hits the "up limit" switch. This sends a pulse
to the latching relay to reverse the motor (and ends the short
pulse). The train travels to the "down limit" switch and reverses.

If the motor can be used to click a switch or move a slide switch,
the following circuit can be used:

REVERSING A MOTOR-3
If the train cannot physically click the slide switch in both directions,
via a linkage, the following circuit should be used:

When power is applied, the relay is not energised and the train must
travel towards the "up limit." The switch is pressed and the relay is
energised. The Normally Open contacts of the relay will close and this
will keep the relay energised and reverse the train. When the down
limit is pressed, the relay is de-energised.
If you cannot get a triple-pole change-over relay, use the following
circuit:

BATTERY MONITOR MkI
A very simple battery monitor can be made with a dual-colour
LED and a few surrounding components. The LED produces
orange when the red and green LEDs are illuminated.
The following circuit turns on the red LED below 10.5v
The orange LED illuminates between 10.5v and 11.6v.
The green LED illuminates above 11.6v

BATTERY MONITOR MkII
This battery monitor circuit uses 3 separate LEDs.
The red LED turns on from 6v to below 11v.
It turns off above 11v and
The orange LED illuminates between 11v and 13v.
It turns off above 13v and
The green LED illuminates above 13v

LOW FUEL INDICATOR
This circuit has been designed from a request by a reader. He
wanted a low fuel indicator for his motorbike. The LED
illuminates when the fuel gauge is 90 ohms. The tank is
empty at 135 ohms and full at zero ohms. To adapt the circuit
for an 80 ohm fuel sender, simply reduce the 330R to 150R.
(The first thing you have to do is measure the resistance of
the sender when the tank is amply.)

QUIZ TIMER
This circuit can be used to indicate: "fastest finger first." It has a
globe for each contestant and one for the Quiz Master.

When a button is pressed the corresponding globe is illuminated.
The Quiz Master globe is also illuminated and the cathode of the
9v1 zener sees approx mid-rail voltage. The zener comes out of
conduction and no voltage appears across the 120R resistor. No
other globes can be lit until the circuit is reset.

TRACKING TRANSMITTER
This circuit can be used to track lots of items.

It has a range of 200 - 400 metres depending on the terrain
and the flashing LED turns the circuit ON when it flashes. The
circuit consumes 5mA when producing a carrier (silence) and
less than 1mA when off (background snow is detected).

BIKE TURNING SIGNAL
This circuit can be used to indicate left and right turn on a motor-bike. Two
identical circuits will be needed, one for left and one for right.

PHONE TAPE-3
This circuit can be used to turn on a tape recorder when the phone line voltage
is less than 15v. This is the approximate voltage when the handset is picked
up. See Phone Tape-1 and Phone Tape-2 in 200 Transistor Circuits eBook
(circuits 1 - 100). When the line voltage is above 25v, the BC547 is turned on
and this robs the base of the second BC547 of the 1.2v it needs to turn on.
When the line voltage drops, the first BC547 turns off and the 10u charges via
the 47k and gradually the second BC547 is turned on. This action turns on the
BC338 and the resistance between its collector-emitter leads reduces. Two
leads are taken from the BC338 to the "rem" (remote) socket on a tape
recorder. When the lead is plugged into a tape recorder, the motor will stop. If
the motor does not stop, a second remote lead has been included with the
wires connected the opposite way. This lead will work. The audio for the tape
recorder is also shown on the diagram. This circuit has the advantage that it
does not need a battery. It will work on a 30v phone line as well as a 50v phone
line.

PHONE TAPE-4
This circuit is identical in operation to the circuit above but uses FET's (Field
Effect Transistors.
15v zeners are used to prevent the gate of each FET from rising above 15v.
A FET has two advantages over a transistor in this type of circuit.
1. It takes very little current into the gate to turn it on. This means the gate
resistor can be very high.
2. The voltage developed across the output of a FET is very low when the FET is
turned on. This means the motor in the tape recorder will operate at full strength.
This circuit has not been tested and the 10k resistor (in series with the first 15v
zener) creates a low impedance and the circuit may not work on some phone
systems.

SEQUENCER
This circuit has been requested by a reader. He wanted to have a display on his jacket that
ran 9 LEDs then stopped for 3 seconds.
The animated circuit shows this sequence:

Note the delay produced by the 100u and 10k produces 3 seconds by the transistor inhibiting
the 555 (taking pin 6 LOW). Learn more about the 555 - see the article: "The 555" on Talking
Electronics website by clicking the title on the left index. See the article on CD 4017. See
"Chip Data eBook" on TE website in the left index.

H-BRIDGE
These circuits reverse a motor via two input lines. Both inputs must not
be LOW with the first H-bridge circuit. If both inputs go LOW at the
same time, the transistors will "short-out" the supply. This means you
need to control the timing of the inputs. In addition, the current
capability of some H-bridges is limited by the transistor types.

The driver transistors are in "emitter follower" mode in this circuit.

Two H-Bridges on a PC board

H-Bridge using Darlington transistors

TOUCH-ON TOUCH-OFF SWITCH
This circuit will create a HIGH on the output when the Touch Plate is touched briefly and
produce a low when the plate is touched again for a slightly longer period of time. Most touch
switches rely on 50Hz mains hum and do not work when the hum is not present. This circuit
does not rely on "hum."

TOUCH-ON TOUCH-OFF SWITCH

SIMPLE TOUCH-ON TOUCH-OFF SWITCH
This circuit will create a HIGH on the output when the Touch
Plate is touched briefly and produce a low when the plate is
touched again.

SHAKE TIC TAC LED TORCH
In the diagram, it looks like the coils sit
on the “table” while the magnet has its
edge on the table. This is just a
diagram to show how the parts are
connected. The coils actually sit flat
against the slide (against the side of
the magnet) as shown in the diagram:
The output voltage depends on how
quickly the magnet passes from one
end of the slide to the other. That's
why a rapid shaking produces a higher
voltage. You must get the end of the
magnet to fully pass though the coil so
the voltage will be a maximum. That’s
why the slide extends past the coils at
the top and bottom of the diagram.

The circuit consists of two 600-turn
coils in series, driving a voltage
doubler. Each coil produces a positive
and negative pulse, each time the
magnet passes from one end of the slide to the other.
The positive pulse charges the top electrolytic via the top diode and the negative pulse charges the lower
electrolytic, via the lower diode.
The voltage across each electrolytic is combined to produce a voltage for the white LED. When the
combined voltage is greater than 3.2v, the LED illuminates. The electrolytics help to keep the LED
illuminated while the magnet starts to make another pass.

FADING LED
The circuit fades the LED ON and OFF at an equal rate.
The 470k charging and 47k discharging resistors have
been chosen to create equal on and off times.

MAINS NIGHT LIGHT
The circuit illuminates a column of 10 white LEDs. The
10u prevents flicker and the 100R also reduces flicker.

RANDOM BLINKING LEDS
This circuit blinks a set of LEDs in a random pattern according to the slight differences in the
three Schmitt Trigger oscillators. The CD4511 is BCD to 7-segment Driver

HEX BUG
This is the circuit from a HEX BUG. It is a surface-mount bug with 6 legs. The pager motor is
driven by an H-Bridge and "walks" to a wall where a feeler (consisting of a spring with a stiff wire
down the middle) causes the motor to reverse.
In the forward direction, both sets of legs are driven by the compound gearbox but when the
motor is reversed, the left legs do not operate as they are connected by a clutch consisting of a
spring-loaded inclined plane that does not operate in reverse.
This causes the bug to turn around slightly.
The circuit also responds to a loud clap. The photo shows the 9 transistors and accompanying
components:

HEX
BUG CIRCUIT

Inclined Dog Clutch

HEX BUG GEARBOX
Hex Bug gearbox consists of a compound gearbox with output "K" (eccentric pin) driving the legs.
You will need to see the project to understand how the legs operate.
When the motor is reversed, the clutch "F" is a housing that is spring-loaded to "H" and drives "H
via a square shaft "G". Gearwheel "C" is an idler and the centre of "F" is connected to "E" via the
shaft. When "E" reverses, the centre of "F" consists of a driving inclined plane and pushes "F"
towards "H" in a clicking motion. Thus only the right legs reverse and the bug makes a turn. When
"E" is driven in the normal direction, the centre of "F" drives the outer casing "F" via an action
called an "Inclined Dog Clutch" and "F" drives "G" via a square shaft and "G" drives "H" and "J" is
an eccentric pin to drive the legs.
The drawing of an Inclined Dog Clutch shows how the clutch drives in only one direction. In the
reverse direction it rides up on the ramp and "clicks" once per revolution. The spring "G" in the
photo keeps the two halves together.

PWM CONTROLLER
This 555 based PWM controller features almost 0% to 100% pulse width regulation using the 100k variable
resistor, while keeping the oscillator frequency relatively stable. The frequency is dependent on the 100k pot
and 100n to give a frequency range from about 170Hz to 200Hz.

LIMIT SWITCHES
This circuit detects when the water level is low and activates solenoid (or pump) 1 for 5
minutes (adjustable) to allow dirty water to be diverted, before filling the tank via solenoid
2.

WAILING SIREN
This circuit produces a penetrating (deafening) up/down siren sound.

MODEL RAILWAY TIME
Here is a simpler circuit than MAKE TIME FLY from our first book of 100 transistor circuits.
For those who enjoy model railways, the ultimate is to have a fast clock to match the scale of the
layout. This circuit will appear to "make time fly" by revolving the seconds hand once every 6 seconds.
The timing can be adjusted by the electrolytics in the circuit. The electronics in the clock is
disconnected from the coil and the circuit drives the coil directly. The circuit takes a lot more current
than the original clock (1,000 times more) but this is the only way to do the job without a sophisticated
chip.

Model Railway Time Circuit Connecting the circuit to the clock coil

For those who want the circuit to take less current, here is a version using a Hex Schmitt Trigger chip:

Model Railway Time Circuit using a 74c14 Hex Schmitt Chip

SLOW START-STOP
To make a motor start slowly and slow
down slowly, this circuit can be used.
The slide switch controls the action.
The Darlington transistor will need a
heatsink if the motor is loaded.

Slow Start-Stop Circuit

VOLTAGE MULTIPLIERS
The first circuit takes a square wave (any amplitude) and doubles it - minus about 2v
losses in the diodes and base-emitter of the transistors.
The second circuit must rise to at least 5.6v and fall to nearly 0.4v for the circuit to work.

Also the rise and fall times must be very fast to prevent both transistors coming on at the
same time and short-circuiting.
The third circuit doubles an AC voltage. The AC voltage rises "V" volts above the 0v rail
and "V" volts below the 0v rail.

CLAP SWITCH
This circuit toggles the LEDs each time it detects a clap or tap or short whistle.
The second 10u is charged via the 5k6 and 33k and when a sound is detected, the
negative excursion of the waveform takes the positive end of the 10u towards the 0v
rail. The negative end of the 10u will actually go below 0v and this will pull the two
1N4148 diodes so the anode ends will have near to zero volts on them.
As the voltage drops, the transistor in the bi-stable circuit that is turned on, will have
0.6v on the base while the transistor that is turned off, will have zero volts on the base.
As the anodes of the two signal diode are brought lower, the transistor that is turned on,
will begin to turn off and the other transistor will begin to turn on via its 100u and 47k.
As it begins to turn on, the transistor that was originally turned on will get less "turn-on"
from its 100u and 47k and thus the two switch over very quickly. The collector of the
third transistor can be taken to a buffer transistor to operate a relay or other device.

INTERCOM
Here is a 2-station intercom using common 8R mini speakers. The "press-to-talk" switches
should have a spring-return so the intercom can never be left ON. The secret to preventing
instability (motor-boating) with a high gain circuit like this is to power the speaker from a
separate power supply! You can connect an extra station (or two extra stations) to this
design.

WARNING BEACON

Here is a 12v Warning Beacon suitable for a car or truck
break- down on the side of the road. The key to the operation
of the circuit is the high gain of the Darlington transistors. The
circuit must be kept "tight" (thick wires) to be sure it will
oscillate.
A complete kits of parts and PC board costs $5.00 plus
postage from: Talking Electronics. Email HERE for details.

PHASE-SHIFT OSCILLATOR also called SINEWAVE OSCILLATOR

This circuit produces a sinewave very nearly equal to rail voltage.
The important feature is the need for the emitter resistor and 10u bypass electrolytic. It
is a most-important feature of the circuit. It provides reliable start-up and guaranteed
operation. For 6v operation, the 100k is reduced to 47k.
The three 10n capacitors and two 10k resistors (actually 3) determine the frequency of
operation (700Hz).
The 100k and 10k base-bias resistors can be replaced with 2M2 between base and
collector.
This type of circuit can be designed to operate from about 10Hz to about 200kHz.

BLOCKING OSCILLATOR also called FLYBACK OSCILLATOR

The circuit produces high voltage pulses (spikes) of about 40v p-p (when the LED is not
connected), at a frequency of 200kHz. The super-bright LED on the output absorbs the
pulses and uses the energy to produce illumination. The voltage across the LED will be
about 3.6v
The winding to the base is connected so that it turns the transistor ON harder until it is
saturated. At this point the flux cannot increase any more and the transistor starts to
turn off. The collapsing magnetic field in the transformer produces a very high voltage
and that's why we say the transformer operates in FLYBACK mode.
This type of circuit will operate from 10kHz to a few MHz.

LOW VOLTAGE FLASHER

This circuit flashes when the voltage drops to 4v.
The voltage "set-point" can be adjusted by
changing the 150k on the base of the first
transistor.

POWER ON

This LED illuminates for a few seconds when the
power is turned on. The circuit relies on the 47u
discharging into the rest of the circuit so that it is
uncharged when the circuit is turned on again.

CAR LOOP DETECTOR

A 25cm dia coil (consisting of 40 turns and 12 turns) is placed in the
centre of a driveway (between two sheets of plastic). When a vehicle is
driven over the coil, it responds by the waveform collapsing. This occurs
because the tank circuit made up of the 40 turns is receiving just enough
feedback signal from the 12 turns to keep it oscillating. When metal is

placed near the coil, it absorbs some of the electromagnetic waves and
the amplitude decreases. This reduces the amplitude in the 12 turns and
the oscillations collapses. The second transistor turns off and the 10k
pulls the base of the third transistor (an emitter-follower) to the 6v rail and
turns on the LED.

ALARM USING 4-BUTTONS

To open the lock, buttons S1, S2, S3, and S4 must be pressed in this order. They must be pressed for more than
0.7 seconds and less than 1.3 seconds.
Reset button S5 and disable button S6 are also included with the other buttons and if the disable button is
pressed, the circuit will not accept any code for 60 seconds. Each of the 3v3 zeners can be replaced with two red
LEDs and this will show how you are progressing through the code. Make sure the LEDs are not visible to other
users.

AUDIO AMPLIFIER (mini)

This project is called "mini" because its
size is small and the output is small.
It uses surface mount technology.

HOW THE CIRCUIT WORKS
The output is push-pull and consumes
less than 3mA (with no signal) but drives
the earpiece to a very loud level when
audio is detected.
The whole circuit is DC coupled and this
makes it extremely difficult to set up.
Basically you don't know where to start
with the biasing. The two most critical
components are 8k2 between the
emitter of the first transistor and 0v rail and the 470R resistor.
The 8k2 across the 47u sets the emitter voltage on the BC 547 and this turns it on. The collector is directly
connected to the base of a BC 557, called the driver transistor. Both these transistors are now turned on and the
output of the BC 557 causes current to flow through the 1k and 470R resistors so that the voltage developed

across each resistor turns on the two output transistors. The end result is mid-rail voltage on the join of the two
emitters.
The 8k2 feedback resistor provides major negative feedback while the 330p prevents high-frequency oscillations
occurring.

CAPACITOR DISCHARGE
UNIT MkII (CDU2)
This project is available as a kit for
$10.80 plus $6.50 post. email
Talking Electronics for details.

This circuit will
operate a two-solenoid point-motor and prevent it
overheating and causing any damage. The
circuit produces energy to change the points and
ceases to provide any more current. This is
carried out by the switching arrangement
within the circuit, by sampling the output voltage.
If you want to control the points with a DPDT
toggle switch or slide switch, you will need two
CDU2 units.

HOW THE CIRCUIT WORKS
The circuit is supplied by 16v AC or DC and the
diode on the input is used to rectify the voltage if
AC is supplied. If nothing is connected to the
output, the base of the BD679 is pulled high and
the emitter follows. This is called an emitter-follower
stage. The two 1,000u electrolytics charge and the
indicator LED turns on. The circuit is now ready.
When the Main or Siding switch is pressed, the
energy from the electrolytics is passed to the point motor and the points change. As the output
voltage drops, the emitter-follower transistor is turned off and when the switch is released, the
electrolytics start to charge again.

The point-motor can be operated via a Double-Pole Double-Throw Centre-Off toggle switch,
providing the switch is returned to the centre position after a few seconds so that the CDU unit can
charge-up.

CAPACITOR DISCHARGE UNIT MkII (CDU2) - modification
If your transformer does not supply 15vAC to 16vAC, you can increase the input voltage by adding
a 100u to 220u electrolytic and 1N4004 diode to the input to create a voltage doubling
arrangement. You can also change one or both the 1,000u electrolytics for 2,200u. This will deliver
a much larger pulse to the point-motor and guarantee operation.

PHONE BUG see also Phone Transmitter 1 and 2 (1-100 circuits)
This circuit connects to a normal phone line and when the voltage drops to less than 15v, the first
transistor is turned off and enables the second transistor to oscillate at approx 100MHz and
transmit the phone conversation to a nearby FM radio.

CODE LOCK
This circuit turns on a relay when the correct code is entered on the 8-way
DIP switches. Two different types of DIP switches are shown.
Keep the top switch off and no current will be drawn by the circuit.
There are 256 different combinations and because the combination is in
binary, it would be very difficult for a burglar to keep up with the settings of
the switches.

LEDS SHOW RELAY STATE
The green LED indicates the relay is not
energised and the red LED shows the
relay is energised.

VOLTAGE DOUBLER
This is a voltage doubler circuit from a bicycle
dynamo design found on the web. The dynamo
produces 6v AC and charges a 3.3FARAD super cap
via 2 diodes and an electrolytic. As you will see, C2,
D3 and D4 are not needed and can be removed.
This is how the circuit works.
The voltage at the mid point of diodes D1 and D2 can
fall to -0.6v and rise to rail voltage plus 0.6v without
any current being supplied from the dynamo.
When the voltage rises more than 0.6v above rail
voltage, the dynamo needs to deliver current and this
will allow the rail voltage to increase. We start with
the dynamo producing negative from the left side and
positive on the right side.
The left side will fall to -0.6v below the 0v rail and the
right side will charge C1 and C2 will simply rise in
exactly the same manner as we described the left
side of the dynamo being able to rise.
Suppose C1 charges to about 7v (which it will be able
to do after a few cycles). The voltage from the
dynamo now reverses and the left side is positive and

the right side is negative. The right side is already sitting at a potential of 7v (via C1) and as the left side increases,
it raises the rail voltage higher by an amount that could be as high as 7v minus 0.6v.
The actual rail voltage will not be as high as this as the 3.3 Farad capacitor will be charging, but if energy is not
taken from the circuit it will rise to nearly 14v or even higher according to the peak voltage delivered by the dynamo.
When the dynamo is delivering energy to the positive rail, it is "pushing down" on the C1 and some of its stored
energy is also delivered. This means it will have a lower voltage across it when the next cycle comes around. C2,
D3 and D4 are not needed and can be removed. In fact, C1 will always have rail voltage on it due to the 47 resistor,
so the voltage doubling will start as soon as the dynamo operates.

Adjustable High Current Regulated Power Supply
There are two ways to add a 2N3055 (TIP3055) as the pass transistor
for a high current power supply. This is handy as most hobbyists will
have one of these in their parts box.

RL must be low enough to guarantee at least a 30mA. It can be a
separate resistor or part of the actual load.

INDUCTIVELY COUPLED POWER
SUPPLY
This circuit is from an Interplak Model PB-12 electric
toothbrush.
A coil in the charging base (always plugged in and on)
couples to a mating coil in the hand unit to form a step
down transformer. The MPSA44 transistor is used as
an oscillator at about 60 kHz which results in much
more efficient energy transfer via the air core coupling
than if the system were run at 50 or 60Hz. The
amplitude of the oscillations varies with the full wave
rectified 100Hz or 120Hz unfiltered DC.

The battery charger is nothing more than a diode to
rectify the signal from the 120 turn coil in the charging
base. Thus the battery is in constant trickle charge as
long as the hand unit is in the base. The battery pack
is a pair of 600mAhr AA NiCd cells.

POWERING A LED
Sometimes the output of a gate does not have sufficient current to
illuminate a LED to full brightness.
Here are two circuits. The circuits illuminate the LED when the output
signal is HIGH. Both circuits operate the same and have the same effect
on loading the output of the gate.

NiCd BATTERY CHARGER
This NiCd battery charger can charge up to 8 NiCd cells connected in series. This
number can be increased if the power supply is increased by 1.65v for each
additional cell. If the BD679 is mounted on a good heatsink, the input voltage can
be increased to a maximum of 25v. The circuit does not discharge the battery if the
charger is disconnected from the power supply.
Usually NiCd cells must be charged at the 14 hour rate. This is a charging current
of 10% of the capacity of the cell for 14 hours. This applies to a nearly flat cell. For
example, a 600 mAh cell is charged at 60mA for 14 hours. If the charging current
is too high it will damage the cell. The level of charging current is controlled by the
1k pot from 0mA to 600mA. The BC557 is turned on when NiCd cells are
connected with the right polarity. If you cannot obtain a BD679, replace it with any
NPN medium power Darlington transistor having a minimum voltage of 30v and a
current capability of 2A. By lowering the value of the 1 ohm resistor to 0.5 ohm, the
maximum output current can be increased to 1A.

CRYSTAL TESTER
This circuit will test crystals from 1MHz to 30MHz. When the crystal oscillates, the
output will pass through the 1n capacitor to the two diodes. These will charge the
4n7 and turn on the second transistor. This will cause the LED to illuminate.

LOW VOLTAGE CUT-OUT
This circuit will detect when the voltage of a 12v battery reaches a low level. This is
to prevent deep-discharge or maybe to prevent a vehicle battery becoming
discharged to a point where it will not start a vehicle. This circuit is different to
anything previously presented. It has HYSTERESIS. Hysteresis is a feature where
the upper and lower detection-points are separated by a gap.
Normally, the circuit will deactivate the relay when the voltage is 10v and when
the load is removed. The battery voltage will rise slightly by as little as 50mV and
turn the circuit ON again. This is called "Hunting." The off/on timing has been
reduced by adding the 100u. But to prevent this totally from occurring, a 10R to
47R is placed in the emitter lead. The circuit will turn off at 10v but will not turn
back on until 10.6v when a 33R is in the emitter.
The value of this resistor and the turn-on and turn-off voltages will also depend on
the resistance of the relay.

THE DARLINGTON TRANSISTOR
Normally a single transistor-stage produces a gain of about 100.
If you require a very high gain, two stages can be used. Two transistors can be
connected connected in many ways and the simplest is DIRECT COUPLING. This
is shown in the circuit below. An even simpler method is to combine two transistors
in one package to form a single transistor with very high gain, called
DARLINGTON TRANSISTOR.
These are available as:
BD679 NPN-Darlington
2N6284 NPN-Darlington
BC879 NPN-Darlington
BC880 PNP-Darlington
TIP122 NPN-Darlington
TIP127 PNP-Darlington

These devices consist of two NPN or PNP transistors but the same result can be
obtained by using a PNP/NPN pair. This is called a Sziklai pair. This arrangement
will have to be created with two separate transistors.
The Darlington transistor can also be referred to as:
"Super Transistor, Super Alpha Pair, Sziklai pair, Complementary Pair,
Darlington transistors have a gain of 1,000 to 30,000. When the gain is 1,000:1 an
input of 1mA will produce a current of 1 amp in the collector-emitter circuit.
The only disadvantage of a Darlington Transistor is the minimum voltage between
collector-emitter when fully saturated. It is 0.6v to 1.5v depending on the current
through the transistor.
A normal transistor has a collector-emitter voltage (when saturated) of 0.2v to 0.5v.
The higher voltage means the transistor will heat up more and requires good
heatsinking. In addition, a Darlington transistor needs 1.2v between base and
emitter before it will turn on. A Sziklai pair only requires 0.6v for it to turn on.

PIC PROGRAMMER
The simplest programmer to program PIC chips is connected to your computer via the serial port. This is a 9-pin
plug/socket arrangement called a SUB-D9 with the male plug on the computer and female on a lead that plugs into
the computer.
The signals that normally appear on the pins are primary designed to talk to a modem but we use the voltages and
the voltage-levels to power a programmer. The voltages on the pins are On or Off. On (binary value "1") means the
pin is between -3 and -25 volts, while Off (binary value "0") means it is between +3 and +25 volts, depending on the
computer. But many serial ports produce voltages of only +8v and -8V and the programmer circuit uses this to
produce a voltage of about 13.5v to put the PIC chip into programming mode. This is the minimum voltage for the
programmer to work. Any computers with a lower voltage cannot be used. That's why the circuit looks so unusual. It is
combining voltages to produce 13v5.
Here are two circuits.
The first circuit is used in our PIC PROGRAMMER - 12 parts project.
Circuit 2 uses more components to produce the same result and circuit 3 uses less components.

FLUORESCENT INVERTER
The simple circuit will drive up to two 20watt fluoro tubes from a
12v supply.
The circuit also has a brightness adjustment to reduce the current
from the battery. See Fluorescent Inverter article for more details.

ZAPPER - 160v
This project will give you a REAL SHOCK. It produces up to 160v and outputs this
voltage for a very short period of time.
The components are taken from an old CFL (Compact Fluorescent Lamp) as the
transistors are high voltage types and the 1u5 electro @400v can also be taken from
the CFL as well as the ferrite core for the transformer.
The CFL has a 1.5mH choke with a DC resistance of 4 ohms. This resistance is too
low for our circuit and the wire is removed and the core rewound with 50 turns for the
feedback winding and 300 turns of 0.1mm wire to produce a winding with a resistance
of about 10 ohms for the primary.
The oscillator is "flyback" design that produces spikes of about 160v and these are
fed to a high-speed diode (two 1N4148 diodes in series) to charge a 1u5 electrolytic
to about 160v. If you put your fingers across the electrolytic you will hardly feel the
voltage. You might get a very tiny tingle at the end of your fingers.
But if this voltage is delivered, then turned off, you get an enormous shock and you

pull yours fingers off the touch pads.
That's what the other part of the circuit does. It turns on a high-voltage transistor for a
very short period of time and this is what makes the circuit so effective.

TELEPHONE AMPLIFIER
This amplifier circuit is used in all home telephones to amplify the signal
from the line to the earpiece. The voltage is taken from the line via a
bridge that delivers a positive rail, no matter how the phone wires are
connected.
A transformer is used to pick off a signal from the phone line and this is
passed through a 22n to the input of the amplifier. Negative feedback is
provided by a 15k and 1n2 capacitor. The operating point for the amplifier
is set by the 100k pot and this serves to provide an effect on the gain of the
amplifier and thus the volume.

VHF AERIAL AMPLIFIER
This amplifier circuit can be used to amplify
VHF television signals. The gain is between
5dB and 28dB. 300ohm twin feeder can be
used for the In/Out leads.

CAR LIGHTS ALERT
This circuit will alert the driver if the lights have been left on.
A warning sound will be emitted from the 12v buzzer when
the driver's door is opened and the lights are on.

MAINS DETECTOR
This circuit detects the "Active" wire of
110v AC or 240v AC via a probe and
does not require "continuity." This makes
it a safe detector.
It uses the capacitance of your body to
create current flow in the detecting part of
the circuit and the sensitivity will depend
on how you hold the insulating case of
the project. No components of the circuit
must be exposed as this will result in
ELECTROCUTION.

SIMPLEST FM BUG

This circuit is the simplest FM circuit you can get. It has no microphone
but the coil is so MICROPHONIC that it will pick up noises in the room
via vibrations on a table.
The circuit does not have any section that determines the frequency. In
the next circuit and all those that follow, the section that determines the
frequency of operation is called the TUNED CIRCUIT or TANK
CIRCUIT and consists of a coil and capacitor. This circuit does not have
this feature. The transistor turns on via the 47k and this puts a pulse
through the 15 turn winding. The magnetic flux from this winding passes
through the 6 turn winding and into the base of the transistor via the 22n
capacitor. This pulse is amplified by the transistor and the circuit is kept
active.
The frequency is determined by the 6 turn coil. By moving the turns
together, the frequency will decrease. The circuit transmits at 90MHz. It
has a very poor range and consumes 16mA. The coil is wound on a
3mm drill and uses 0.5mm wire.

A GOOD ONE-TRANSISTOR CIRCUIT

This circuit uses a TUNED CIRCUIT or TANK CIRCUIT to create the
operating frequency. For best performance the circuit should be built on

a PC board with all components fitted close to each other. The photo
below shows the components on a PC board:

AN IMPROVED DESIGN

This design uses a "slug tuned coil" to set the frequency. This means the slug can be screwed in
and out of the coil. This type of circuit does not offer any improvement in stability over the previous
circuit. (In later circuits we will show how to improve stability. The main way to improve stability is
to add a "buffer" stage. This separates the oscillator stage from the output.)
The antenna is connected to the collector of the transistor and this "loads" the circuit and will
cause drift if the bug is touched. The range of this circuit is about 200 metres and current
consumption is about 7mA. The microphone has been separated from the oscillator and this allows
the gain of the microphone to be set via the 22k resistor. Lowering the resistor will make the
microphone more sensitive. This circuit is the best you can get with one transistor.

MORE STABILITY

If you want more stability, the antenna can be tapped off the top of the tank circuit. This actually
does two things. It keeps the antenna away from the highly active collector and turns the coil into
an auto-transformer where the energy from the 8 turns is passed to a single turn. This effectively
increases the current into the antenna. And that is exactly what we want.
The range is not as far but the stability is better. The frequency will not drift as much when the bug
is held. As the tap is taken towards the collector, the output increase but the stability deceases.

2-TRANSISTOR CIRCUIT
The next progressive step is to add a transistor to give the electret microphone more sensitivity.
The electret microphone contains a Field Effect Transistor and you can consider it to be a stage of
amplification. That's why the electret microphone has a very good output.
A further stage of amplification will give the bug extremely good sensitivity and you will be able to
pick up the sound of a pin dropping on a wooden floor.
Many of the 1 transistor circuits over-drive the microphone and this will create a noise like bacon
and eggs frying. The microphone's used by Talking Electronics require a load resistor of 47k for a
6v supply and 22k for a 3v supply. The voltage across the microphone is about 300mV to 600mV.
Only a very simple self-biasing common-emitter stage is needed. This will give a gain of approx 70
for a 3v supply. The circuit below shows this audio amplifier, added to the previous transmitter
circuit. This circuit is the best design using 2 transistors on a 3v supply. The circuit takes about
7mA and produces a range of about 200 - 400metres.

Five points to note in the circuit above:
1. The tank circuit has a fixed 39p and is adjusted by a 2-10p trimmer. The coil is stretched to get
the desired position on the band and the trimmer fine tunes the location.
2. The microphone coupling is a 22n ceramic. This value is sufficient as its capacitive reactance at
3-4kHz is about 4k and the input to the audio stage is fairly high, as noted by the 1M on the base.
3. The 1u between the audio stage and oscillator is needed as the base has a lower impedance as
noted by the 47k base-bias resistor.
4. The 22n across the power rails is needed to keep the rails "tight." Its impedance at 100MHz is
much less than one ohm and it improves the performance of the oscillator enormously.
5. The coil in the tank circuit is 5 turns of enameled wire with air core. The secret to long range is
high activity in the oscillator stage. The tank circuit (made up of the coil and capacitors across it)
will produce a voltage higher than the supply voltage due to the effect known as "collapsing
magnetic field" and this occurs when the coil collapses and passes its reverse voltage to the
capacitor. The antenna is also connected to this point and it receives this high waveform and
passes the energy to the atmosphere as electromagnetic radiation.
When the circuit is tightly constructed on a PC board, the frequency will not drift very much if the
antenna is touched.

THE VOYAGER
The only way to get a higher output from two transistors is to increase the
supply voltage.
The following circuit is available from Talking Electronics as a surface-mount
kit, with some components through-hole. The project is called THE
VOYAGER.

All the elements of good design have been
achieved in this project. The circuit has a
slightly higher output than the 3v circuit
above, but most of the voltage is lost across
the emitter resistor and not converted to RF.
The main advantage of this design is being
able to connect to a 9v battery. In a technical
sense, about half the energy is wasted as the
stages actually require about 4v - 5v for
maximum output.

HAND-HELD MICROPHONE

This circuit is suitable for a hand-held microphone. It does not have an
audio stage but that makes it ideal as a microphone, to prevent
feedback. The output has a buffer stage to keep the oscillator away
from the antenna. This gives the project the greatest amount of stability
-rather than the highest sensitivity.

INCREASING THE RANGE

To increase the range, the output must be increased. This can be done by using
an RF transistor and adding an inductor. This effectively converts more of the
current taken by the circuit (from the battery) into RF output. The output is
classified as an untuned circuit. A BC547 transistor is not suitable in this location
as it does not amplify successfully at 100MHz. It is best to use an RF transistor
such as 2N3563.

MORE RANGE
More output can be obtained by increasing the supply voltage and adding a
capacitor across the inductor in the output stage to create a tuned output.
The 5-30p must be adjusted each time the frequency of the bug is changed. This
is best done with a field strength meter. See Talking Electronics Field Strength
Meter project.

A tuned output stage delivers more output

The 2N3563 is capable of passing 15mA in the buffer stage and about 30% is
delivered as RF. This makes the transmitter capable of delivering about 22mW.

EMITTER TAP
The following circuit taps the emitter of the oscillator stage. The collector or the
emitter can be tapped to produce about the same results, however tapping the
emitter "loads" the oscillator less. The 47p capacitor is adjusted to "pick-off" the
desired amount of energy from the oscillator stage. It can be reduced to 22p or
10p.

Tapping the emitter of the oscillator transistor

GOING FURTHER

The next stage to improve the output, matches the impedance of
the output stage to the impedance of the antenna.
The impedance of the output stage is about 1k to 5k, and the
impedance of the antenna is about 50 ohms.
This creates an enormous matching problem but one effective
way is with an RF transformer.
An RF transformer is simply a transformer that operates at high
frequency. It can be air cored or ferrite cored. The type of ferrite
needed for 100MHz is F28. The circuit above uses a small ferrite
slug 2.6mm dia x 6mm long, F28 material.
To create an output transformer for the circuit above, wind 11
turns onto the slug and 4 turns over the 11 turns. The ferrite core
will do two things. Firstly it will pass a high amount of energy from
the primary winding to the antenna and secondly it will
THE RF TRANSFORMER prevent harmonics passing to the antenna. The transformer
approximately doubles the output power of the transmitter.

WATER LEVEL DETECTOR
This circuit can be used to automatically keep the header tank filled. It
uses a double-pole relay.

BATTERY CHARGER - world's simplest automatic charger
This is the world's simplest automatic battery charger.
It consists of 6 components, when connected to a 12v DC plug pack. The plug pack must produce more
than 15v on no-load (which most plug packs do.) An alternative 15v transformer and a centre-tapped
transformer is also shown. A centre-tapped transformer is referred to as: 15v-CT-15v or 15-0-15
The relay and transistor are not critical as the 1k pot is adjusted so the relay drops-out at 13.7v.
The plug pack can be 300mA, 500mA or 1A and its current rating will depend on the size of the 12v battery
you are charging.
For a 1.2AH gel cell, the charging current should be 100mA. However, this charger is designed to keep the
battery topped-up and it will deliver current in such short bursts, that the charging current is not important.
This applies if you are keeping the battery connected while it is being used. In this case the charger will add
to the output and deliver some current to the load while charging the battery. If you are charging a flat cell,
the current should not be more than 100mA.
For a 7AH battery, the current can be 500mA. And for a larger battery, the current can be 1Amp.

SETTING UP
Connect the charger to a battery and place a digital meter across the battery. Adjust the 1k pot so the relay
drops out as soon as the voltage rises to 13.7v.
Place a 100R 2watt resistor across the battery and watch the voltage drop.
The charger should turn on when the voltage drops to about 12.5v. This voltage is not important.
The 22u stops the relay "squealing" or "hunting" when a load is connected to the battery and the charger is

charging. As the battery voltage rises, the charging current reduces and just before the relay drops out, it
squeals as the voltage rises and falls due to the action of the relay. The 22u prevents this "chattering".
To increase the Hysteresis: In other words, decrease the voltage where the circuit cuts-in, add a 270R
across the coil of the relay. This will increase the current required by the transistor to activate the relay and
thus increase the gap between the two activation points. The pull-in point on the pot will be higher and you
will have re-adjust the pot, but the drop-out point will be the same and thus the gap will be wider.
In our circuit, the cut-in voltage was 11.5v with a 270R across the relay.
Note: No diode is needed across the relay because the transistor is never fully turned off and no back EMF
(spike) is produced by the relay.

BATTERY CHARGER MkII - a very simple design to keep a battery "topped
up."

This is a very simple battery charger to keep a battery "nearly fully charged."
It consists of 7 components, when connected to a 12v - 18v DC plug pack. The plug pack must produce
more than 15v on no-load (which most 12v plug packs do.)
For a 1.2AH gel cell, up to a 45Ahr car or boat battery, this charger will keep the battery topped-up and can
be connected for many months as the battery will not lose water due to "gassing."
The output voltage is 13.2v and this is just enough to keep the battery from discharging, but will take a very
long time to charge a battery, if it is flat because a battery produces a "floating charge" of about 13.6v when
it is being charged (at a reasonable current) and this charger is only designed to deliver a very small current.
There is a slight difference between a "old-fashioned" car battery (commonly called "an accumulator") and a
sealed battery called a Gel Cell. The composition of the plates of a gel cell is such that the battery does not
begin to "gas" until a high voltage is reached. That is why it can be totally closed and only has rubber bungs
that "pop" if gas at high pressure develops due to gross over-charging. That's why the charging voltage
must not be too high and when the battery is fully charged, the charging current must drop to a very low
level.

GELL CELL BATTERY CHARGER
This circuit will charge gell cell batteries at 300mA or 650mA or 1.3A,
depending on the CURRENT SENSING resistor in the 0v rail. Adjust
the 5k pot for 13.4v out and when the battery voltage reaches this
level, the current will drop to a few milliamps. The plug pack will need
to be upgraded for the 650mA or 1.3A charge-current. The red LED
indicates charging and as the battery voltage rises, the current-flow
decreases. The maximum is shown below and when it drops about
5%, the LED turns off and the current gradually drops to almost
zero.

TRANSISTOR TESTER COMBO-2
This circuit uses an IC but it has been placed in this eBook as it is a transistor tester.
The circuit uses a single IC to perform 3 tests:
Test 1: Place the transistor in any orientation into the three terminals of circuit 1 (below, left) and a red LED will
detect the base of a PNP transistor an a green LED will indicate the base of an NPN transistor.
Test 2: You now now the base lead and the type of transistor. Place the transistor in Test 2 circuit (top circuit) and
when you have fitted the collector and emitter leads correctly (maybe have to swap leads), the red or green LED
will come on to prove you have fitted the transistor correctly.
Test 3: The transistor can now be fitted in the GAIN SECTION. Select PNP or NPN and turn the pot until the LED
illuminates. The value of gain is marked on the PCB that comes with the kit. The kit has ezy clips that clip onto the
leads of the transistor to make it easy to use the project.
The project also has a probe at one end of the board that produces a square wave - suitable for all sorts of audio
testing and some digital testing.
Project cost: $22.00 from Talking Electronics.

LOW MAINS DROPOUT
This circuit will turn off a device if the main drops by a say 15v. The
actual voltage is adjustable. The first thing to remember is this: The
circuit detects the PEAK voltage and this is the voltage of the zener
diodes.
For 240v mains, the peak is 338v.
For a voltage drop of about 12v(RMS), the zener diodes need to have a
combined voltage of 320v (you will need 6 x 47v + 1 x 20v + 1 x 18v).
The 10k resistor will have about 18v across it and the current will be
nearly 2mA. The wattage will be 36mW.
For a voltage drop of about 27v(RMS), you will need zeners for a total
of 300v by using 6 x 47v + 1 x 18v. The voltage across the 10k resistor
will be 38v and the current will be nearly 4mA. The wattage dissipated
by the 10k resistor will be 150mW.
The 10u prevents very sharp dips or drops from activating the circuit.
As the voltage drops, this drop in voltage will be passed directly to the
top of the 10k resistor and as the voltage drops, the current into the
base of the transistor will reduce. This current is amplified by the
transistor and when it is not sufficient to keep the relay activated, it will
drop-out.

Circuit Symbols
The list below covers almost every symbol you will find on an electronic circuit diagram. It allows you to identify a
symbol and also draw circuits. It is a handy reference and has some symbols that have never had a symbol before, such
as a Flashing LED and electroluminescence panel.
Once you have identified a symbol on a diagram you will need to refer to specification sheets to identify each lead on
the actual component.
The symbol does not identify the actual pins on the device. It only shows the component in the circuit and how it is
wired to the other components, such as input line, output, drive lines etc. You cannot relate the shape or size of the
symbol with the component you have in your hand or on the circuit-board.
Sometimes a component is drawn with each pin in the same place as on the chip etc. But this is rarely the case.
Most often there is no relationship between the position of the lines on the circuit and the pins on the component.

That’s what makes reading a circuit so difficult.

This is very important to remember with transistors, voltage regulators, chips and so many othe r components as the
position of the pins on the symbol are not in the same places as the pins or leads on the component and sometimes the
pins have different functions according to the manufacturer. Sometimes the pin numbering is different according to
the component, such as positive and negative regulators.
These are all things you have to be aware of.

You must to refer to the manufacturer’s specification sheet to identify each pin, to be sure you have identified them
correctly.

Colin Mitchell

CIRCUIT SYMBOLS
Some additional symbols have been added to the following list. See Circuit Symbols on the index of
Talking Electronics.com

to Index

IC PINOUTS
The following list covers just a few of the IC's on the market and these are the "simple" or "basic" or "digital" or "op-amp"
IC's suitable for experimenting.
When designing a circuit around an IC, you have to remember two things:
1. Is the IC still available? and
2. Can the circuit be designed around a microcontroller?
Sometimes a circuit using say 3 or 4 IC's can be re-designed around an 8-pin or 16-pin microcontroller and the program can
be be kept from prying eyes due to a feature called "code protection." A microcontroller project is more up-to-date, can
be cheaper and can be re-programmed to alter the features.
This will be covered in the next eBook. It is worth remembering - as it is the way of the future.

to Index
All the resistor colours:
This is called the "normal" or "3 colour-band" (5%) range. If you want the 4 colour-band (1%) series, refer to
Talking Electronics website and click: Resistors 1% on the left index. Or you can use the table below.

to Index
MAKE ANY RESISTOR VALUE:
If you don't have the exact resistor value for a project, don't worry. Most
circuits will work with a value slightly higher or lower.
But if you want a particular value and it is not available, here is a chart.
Use 2 resistors in series or parallel as shown:

Required Series/ Actual
R1 R2
Value Parallel value:
10 4R7 S 4R7 9R4
12 10 S 2R2 12R2
15 22 P 47 14R9
18 22 P 100 18R
22 10 S 12 22
27 22 S 4R7 26R7
33 22 S 10 32R
39 220 P 47 38R7
47 22 S 27 49
56 47 S 10 57
68 33 S 33 66
82 27 S 56 83

There are other ways to combine 2 resistors in parallel or series to get a
particular value. The examples above are just one way.
4R7 = 4.7 ohms

to Index
MAKE ANY CAPACITOR VALUE:
If you don't have the exact capacitor value for a project, don't worry. Most
circuits will work with a value slightly higher or lower.
But if you want a particular value and it is not available, here is a chart.
Use 2 capacitors in series or parallel as shown. "p" is "puff" but can be "n"
(nano) or "u" (microfarad).

Required Series/ Actual
C1 C2
Value Parallel value:
10 4p7 P 4p7 9p4
12 10 P 2p2 12p2
15 22 S 47 14p9
18 22 S 100 18p
22 10 P 12 22
27 22 P 4p7 26p7
33 22 P 10 32p
39 220 S 47 38p7
47 22 P 27 49
56 47 P 10 57
68 33 P 33 66
82 27 P 56 83

There are other ways to combine 2 capacitors in parallel or series to get a
particular value. The examples above are just one way. 4p7 = 4.7p

101 200 transistorcircuits

More Related Content

What's hot (20)

Viewers also liked (8)

Similar to 101 200 transistorcircuits (20)

Recently uploaded (20)

101 200 transistorcircuits