Anupam CV - Process & system engineer power plants (Renewable and non-renewable)

Anupam CV - Process & system engineer power plants (Renewable and non-renewable)

• 1.
  ANUPAM DAS CAREER OBJECTIVE Towork as a responsible team member in the leading company, to apply my knowledge, abilities and skills to the fullest in technical field and to reach the pinnacle of my field by working dedicatedly in challenging environment PERSONAL DETAILS ACEDEMIC DETAILS B.Tech (Mechanical) University: Gauhati University Institute: Assam Engineering College, Guwahati Course School / College Board/ University Year Of Passing Percentage S.S.C Vivekananda Kendra Vidyalaya CBSE 2001 79.6% H.S.C Vivekananda Kendra Vidyalaya CBSE 2003 65% B. E. Assam Engineering College Gauhati University 2008 81% Address #84/A, 7th A cross, Rajashree layout, Munnekolala, Marathahalli Post, Bangalore, Karnataka, India Contact Number +91-8088184480, +91-8971044700 Date of Birth 19th September, 1984 Gender Male E-mail [email protected] Known Languages English, Hindi, Bengali, Assamese, Kannada Nationality Indian
• 2.
  CURRICULUM ACHIEVEMENTS  Secureda place in top three rankings based on academic performance in B.E., Mechanical Engineering, Gauhati University WORK EXPERIENCE  GE INDIA TECHNOLOGY CENTRE PVT. LTD. GE OIL AND GAS, BANGALORE OFFICE DURATION- FROM 5th August, 2013 TO TILL DATE  LEAD ENGINEER  PROJECTS EXECUTED: 1) Project: Gas Turbine Model MS5002C+Gearbox+Centrifugal compressor 2BCL406/B, Ourhoud (Algeria) Client: Ourhoud/Sonatrach, Bonatti (EPC)  MS5002C is a heavy duty machine used to drive a compressor. As a System Engineer in the Job I had understand the customer specifications, implement the requirements in our documents. Attend meetings and co- ordinate inter-department and provide all data required for smooth progress of the job.  Preparation of Gas turbine and compressor system auxiliaries PIDs of Lube oil system, Hydraulic/control oil system, Lube oil cooler, fuel gas scrubber system, fuel gas system, starting system, GT sealing and cooling system, Control and protection system, filter house system, ventilation system, fire fighting system, gearbox system, compressor sealing system and customer process PID indicating the Gas turbine and compressor only, which are in GENP scope.  Preparation of Electrical load list  Preparation of Utility list  Preparation of Seal gas panel specification  Preparation of seal gas panel layout  Review of Supplier offers for seal gas panel.  Preparation of painting specification  Attended the HAZOP in Italy, Fano. 2) Project: AeroderivativeGas Turbine Model PGT25 Base+Centrifugal compressor PCL603, HassiR’Mel (Algeria) - Job in progress Client: Sonatrach, Bonatti (EPC)  PGT25 base is a aero-derivative machine used to drive a compressor. The application of the compressor is mainly to transport gas from one station to another. As a System Engineer in the Job I had to understand the
• 3.
  customer specifications, implementthe requirements in our documents. All major documents are sent to Customer and project is 30% complete from engineering design front.  Preparation of Gas turbine and compressor system auxiliaries PIDs of Lube oil system, Hydraulic/control oil system, Lube oil cooler, fuel gas, fuel gas system, fuel gas metering system, Synthetic oil system, Hydraulic starting system, GT sealing and cooling system, Control and protection system, filter house system, ventilation system, fire-fighting system, gearbox system, compressor sealing system and customer process PID indicating the Gas turbine and compressor only, which are in GENP scope.  Preparation of Electrical load list  Preparation of Utility list  Preparation of Seal gas panel specification  Preparation of seal gas panel layout (in progress)  Preparation of painting specification 3) Project: Turbo-expander + Compressor EC401 Unit , Hackberry (Lousiana, USA) - Job in progress Client: CCJV for Cameroon LNG, LLC This is a turbo-expander job, wherein hydrocarbon gas is expanded and the energy generated is used in running a compressor.  Preparation of Turbo-expander and axial compressor PID indicating the seal gas system, gas inlet lines, the sealing system and customer process indicating the anti-surge system. Preparation of active magnetic bearing control and instrumentation system.  Preparation of specification for heaters, valves, filters, instruments.  Review of supplier offers for various seal gas components (like heater, valves, filters, instruments etc) and aligning with our specification requirements.  Preparation of Electrical load list and Utility list  Carrying out meetings for jobs at various stages 4) Project: Turbo-expander-Generator, Jamnagar (India) - Job in progress Client: Reliance Industries Limited This is a turboexpander job, wherein hydrocarbon gas is expanded and the energy generated is used in running a Generator. This Job is in a advance stage and handed over to me recently.  Interdepartmental co-ordination to close all ongoing issues.  Interaction with suppliers for preparation of seal gas panel layout.  Preparation of specification for control valves, heaters, filters, instruments etc meeting all the certifications, zone classification, testing requirements as per Customer requirements.
• 4.
   Review ofsupplier offers for various Components of on baseplate and seal gas components and aligning with our specification requirements.  Preparation of Utility list for the project.  Preparation of Electrical load list.  Sizing of safety valve and control valves using API520 and Emerson guidelines respectively. And preparation of specifications of these items.  Working out of HAZOP action points.  TATA CONSULTING ENGINEERS LIMITED POWER BUSINESS UNIT, BANGALORE OFFICE DURATION- FROM 1st August, 2008 TO 2nd August, 2013.  ASISTANT MANGER -- (E2 GRADE)  PROJECTS EXECUTED: 1) 1X50 MW, Concentrated Solar Thermal Plant, Andhra Pradesh (Under Execution) Client: Megha Engineering and Infrastructure Limited  Concept Notes of (a) Boiler feed pump, (b) Condensate extraction pump, (c) Gland steam sealing (Night/day mode), (d) Steam Generator heat exchangers, (e) Compressed air system, (f) Fuel oil system  PIDs/Flow Diagrams of (a) Main steam, CRH & HRH system, (b) Steam generator heat exchangers, (c) Condensate system, (d) Feedwater system, (e) Extraction steam system, (f) Heater drain and vent system, (g) Auxiliary steam system, (h) Blow down system, (i) HFO & LDO Unloading System  Specification preparation for (a) Steam generator heat exchangers, (b) Turbine cycle and auxiliaries, (c) Compressed air system (d) Moisture separator, (e) Flash tanks (f) Fuel oil system  TG cycle equipments sizing, Flash tanksand Control valves sizing for the entire Turbine generator and HTF cycle  Preparation of GA of Ullage (HTF purification system) system  Preparation of logics for plant PIDs  Inter-department co-ordination 2) Pre-Bid R&M Services/Engineering 3x200MW Ramagundam (Andhra Pradesh) Thermal Power Plant, NTPC plant (Commissioned in the year 1978) Client: General Electric  Preparation of functional specification, review of bids and preparation of TER for Boiler feed pumps  Preparation of functional specification, review of bids and preparation of TER for Condensate extraction pumps  Preparation of functional specification, review of bids and preparation of TER for vacuum pumps
• 5.
   Preparation ofdatasheets for feed control station, motorized valves, quick closing non-return valves, other valves and hangers, review of offers from vendors and preparation of TER.  Study of the existing plant layouts, PIDs, HBDs and GAs to fit the new equipments. 3) Prebid Engineering Services for 1 x 300 MW Masinloc Thermal Power, Phillipines ProjectClient: Daewoo  Calculation and sizing of HP-LP bypass system. 4) Detail Engineering Services for 1131.1 MW Combined cycle [power plant in Algeria. ProjectClient: Daewoo  Preparation of General arrangement of Hydrogen generation and storage building. 5) 700 MW Class GE reference plant, Coal based Thermal Power Plant, India Client: GE  Preparation of basic study for (a) Extraction steam system, (b) HP-LP bypass system  Preparation of PID for (a) Extraction steam system, (b) HP-LP bypass system  Specification preparation for HP-LP bypass system  Preparation of Technical Evaluation Report (TER) for HP-LP bypass system 6) 5X270 MW, Thermal Power Plant, Amravati & Nasik,Maharastra Client: Indiabulls Power Limited  Review of (a) BTG (BHEL), (b) Hydrogen generation system, (c) Compressed air system documents/drawings  Preparation of basic study for (a) Fuel oil system (b) Compressed air system  Preparation of specification of (a) Fuel oil system, (b) Compressed air system  Preparation of system and distribution PIDs for (a) Compressed air system  Preparation of technical evaluation report for (a) Fuel oil system, (b) Compressed air system  Inter-department co-ordination 7) 2X150 MW, Thermal Power Plant, Bhadreswar, Gujarat Client: OPG
• 6.
   Review ofBTG (BHEL) documents/drawings  Concept Notes of (a) Stack sizing, (b) Fuel oil system  PIDs/Flow Diagrams of Fuel oil system  Specification preparation for (a) Fuel oil system, (b) Plate heat exchanger, (c) Cooling water pumps, (d) Miscellaneous pumps  Preparation of technical evaluation report for (a) Fuel oil system, (b) Plate heat exchanger, (c) Cooling water system, (d) Miscellaneous pumps  Inter-department co-ordination  TECHNICAL SKILLS:  Thermoflow & Thermoflex for HBD generation, Intools for control valve and orifice sizing, HYSYS  Basic Understanding of ASME pressure vessel Codes and Standards  Understanding of P&IDs and process  System design and calculations COMPUTER KNOWLEDGE HBD generation THERMOFLOW Drafting Software AUTO CAD Programming Languages C basics General Pro E, CNC, Microsoft Excel, Word, Power Point, In-tools (control valves & orifice design) INDUSTRIAL EXPOSURE  Visited GE Nuovo Pignone (Italy) Workshop to get exposure to the manufacturing of the Gas Turbine and Centrifugal compressor.  Visited the 1X50 MW, Concentrated Solar Thermal Plant (Andhra Pradesh) during the commissioning phase.  Undergone one month vocational summer training at Hindustan Machine Tools (HMT), Pinjore, Haryana in Tractor division during summer of 2007
• 7.
   Undergone onemonth training in CNC technology at tool room and training center (TRTC), Guwahati during summer vacation 2005  Anticipated team members in workshop during component manufacture in TRTC for client.  Undergone 10 days training program in Dibrugarh Railway workshop, Assam during summer vacation 2005.  Visited IIT, Mumbai’sConcentrated Solar Thermal power plant in Gurgaon, August 2012.  Tata Consulting Engineers Limited in-house training in Process and technology of conventional and non-conventional power plants EXTRA CURRICULAR ACTIVITIES  Actively participated in the Corporate Social Responsibility activities in Tata Consulting Engineers from past 4 years 9 months DECLARATION I hereby declare that the information furnished above is true the best of my knowledge. Name : Anupam Das Place : Bangalore, Karnataka