Basics of metrology
- 1. Basics of Metrology Lecture by Mr.C.Ramkumar, Assistant Professor/Department of Mechanical Engineering KIT-KalaignarKarunanidhi Institute of Technology
- 2. Introduction to Metrology Need Work piece, Instruments –person –Environment –Their effect on precision and accuracy Errors Errors in Measurements Types Control Types of standards BASICS OF METROLOGY
- 3. • Measurement is a process of comparing inputs with pre-defined standard and giving the output. • Metrology is a science of measurement • Metrology is also concerned with the inspection and its variousindustrial techniques • For every kind of quantity measured, there must be a unit to measure it MEASUREMENTS - Introduction
- 4. 1.Measurand, a physical quantity such as length, weight, and angle to be measured 2. Reference, to compare the measurand (physical quantity) with a known standard for evaluation 3. Standard/Reference, the physical quantity or property to which quantitative comparisons are to be made, which is internationally accepted STANDARD (Known Quantity) MEASURAND (Unknown Quantity) COMPARISON PROCESS RESULT (Numerical Value) MEASUREMENTS - Introduction
- 5. To convert physical parameters into meaningful numbers. To determine the true dimensions of a part. To increase our knowledge and understanding of the world. Needed for ensuring public health and human safety. To test if the elements that constitute the system function as per the design. For evaluating the performance of a system. To ensure interchangeability with a view to promoting mass production. To establish the validity of design and for finding new data and new designs. NEED FOR MEASUREMENT
- 6. • Industrial Metrology - Industrial metrology’s purpose is to ensure that instruments, used in a wide variety of industries, are functioning properly. • Scientific Metrology - This form of metrology deals with the organization and development of measurement standards and with their maintenance. • Legal Metrology - Concerned with the measurements that influence economic transactions, legal metrology is a very refined type of metrology. TYPES OF METROLOGY
- 7. A generalized measurement system consists of the following components: 1. Primary Sensing Element 2. Variable Conversion Element 3. Variable Manipulation Element 4. Data Processing Element 5. Data Transmission System 6. Data Presentation Element COMPONENTS OF GENERALIZED MEASUREMENT SYSTEM
- 9. 1. Primary Sensing Element: The primary sensing element receives signal of the physical quantity to be measured as input. It converts the signal to a suitable form (electrical, mechanical or other form), so that it becomes easier for other elements of the measurement system, to either convert or manipulate it. 2. Variable Conversion Element: Variable conversion element converts the output of the primary sensing element to a more suitable form. It is used only if necessary. 3. Variable Manipulation Element: Variable manipulation element manipulates and amplifies the output of the variable conversion element. It also removes noise (if present) in the signal. COMPONENTS OF GENERALIZED MEASUREMENT SYSTEM
- 10. 4. Data Processing Element: It processes the data signal received from the variable manipulation element and produces suitable output. 5. Data Transmission System: Data Transmission System is simply used for transmitting data from one element to another. It acts as a communication link between different elements of the measurement system. 6. Data Presentation Element: It is used to present the measured physical quantity in a human readable form to the observer. LED displays are most commonly used as data presentation elements in many measurement systems. COMPONENTS OF GENERALIZED MEASUREMENT SYSTEM
- 11. Physical Quantity - Temperature Sensing Element - Bulb Conversion Element – Pressure Transmission Element Manipulation Element Presentation Element Element Conversion COMPONENTS OF GENERALIZED MEASUREMENT SYSTEM
- 12. In metrology (the science of measurement), a standard is an object, or system that bears a defined relationship to a unit of measurement of a physical quantity. Depending on functions and applications, standards of measurement are classified as follows: (i) International Standards (ii) Primary Standards (iii) Secondary Standards (iv) Working Standards STANDARDS
- 13. Defined by International agreement Periodically evaluated & checked by absolute measurements in terms of fundamental units of physics represent certain units of measurement to the closest possible accuracy attainable by the science and technology of measurement These standards are not available to ordinary uses like measurement and calibrations. i. International Standardsi
- 14. Main function is the calibration and verification of secondary standards These are maintained at the National Standards Laboratories in different countries. For India, it is National Physical Laboratory at New Delhi. The primary standards are not available for the use outside the National Laboratory. These primary standards are absolute standards of high accuracy that can be used as ultimate reference standards to check, calibrate and certify the secondary standards. ii. Primary Standards
- 15. Basic reference standards used by the measurement and calibration laboratories in industries These standards are maintained by the particular industry to which they belong Each industry has its own secondary standard Each laboratory periodically sends its secondary standard to the national standards laboratory for calibration and comparison against the primary standard After comparison and calibration, the National Standards Laboratory returns the secondary standards to the particular industrial laboratory with a certification of measuring accuracy in terms of primary standards iii. Secondary Standards
- 16. main tools of a measuring laboratory used to check and calibrate laboratory instrument for accuracy and performance. For example, manufacturing of mechanical components such as shafts, bearings, gears etc, use a standard called working standard for checking the component dimensions. Example: Plug gauge is used for checking the bore diameter of bearings. iv. Working Standards
- 17. • Physical quantity is expressed in Units. • Types: 1. Primary Units – m, Kg, KJ 2. Supplementary Units - rad 3. Derived Units – Kg/KJ UNITS
- 18. 1. Direct Comparison 2. Indirect Comparison 3. Comparative Method 4. Coincidence Method 5. Fundamental Method 6. Contact Method 7. Transposition Method 8. Complementary Method 9. Deflection Method 10. Contactless method TYPES OF MEASUREMENTS / METHODS OF MEASUREMENTS
- 19. 1. Direct Method Measurements are directly obtained Ex.: Vernier Caliper, Scales. 2. Indirect Method Obtained by measuring other quantities. Ex: Measurement of strain induced in a bar due to the applied force
- 20. 3. Comparative Method It’s compared with other value. known Ex: Comparators. 4. Coincidence Method: Measurements coincide with certain lines and signals. Ex: Comparators. 5. Fundamental Method: Measuring a quantity directly in related with the definition of that quantity.
- 21. 6. Transposition Method: Quantity to be measured is first balanced by a known value and then balanced by an other new known value. Ex: Determination of mass by balancing methods. 7. Complementary Method: The value of quantity to be measured is combined with known value of the same quantity. Ex: Determination of the volume of a solid by liquid displacement Volume. 22
- 22. 1. Deflection and Null type instruments 2. Analog and Digital instruments 3. Active and passive type instruments 4. Automatic and manually operated instruments 5. Absolute and secondary instruments 6. Contacting and non-contacting instruments 7. Intelligent instruments TYPES OF MEASURING INSTRUMENTS
- 23. The weight indicated by of the object is the deflection or of a a scale. pointer on Ex. Spring movement graduated Balance 1. Deflection and Null type instruments The effect caused by the quantity to be measured is nullified. For example, consider the measurement of weight by an ordinary beam balance as shown in fig. The unknown weight placed in one-side causes the beam and the pointer to deflect. Ex. Beam Balance
- 24. 2. Analog and Digital Instruments
- 25. In active instruments, the quantity being measured just activates the magnitude of some, external power input source, which in turn produces the measurement. In this type of instruments, another external energy input source is present apart from the quantity to be measured. 3. Active and Passive Type Instruments In passive type instruments, output is produced entirely by the quantity being measured.
- 26. 4. Manual and Automatic Instruments Manual instruments require the services of a human operator. When the process of null balance is automated, it is known termed as automatic instruments.
- 27. 5. Absolute and Secondary Instruments instruments Absolute give the value of the are those which quantity to be measured, in terms of the constants of the instrument and their deflection only. Secondary Instrument shows deflection directly in terms of electrical quantity like voltage, current, power and frequency. These instruments are calibrated by comparison with an absolute instrument.
- 28. 6. Contacting and Non-Contacting Instruments
- 29. 7. Intelligent Instrument Microprocessor are incorporated with measuring instrument
- 30. ACCURACY Vs PRECISION Measurement is an act of assigning an accurate and precise value to a physical variable. What is the difference between Precision andAccuracy Accuracy is a measure of rightness Precision is a measure of exactness ACCURACY Vs PRECISION
- 31. Accuracy is the ability of the instrument to measure the accurate value (Conformity) Precision refers to how closely individual measurements agree with each other (Repeatability) ACCURACY AND PRECISION
- 32. 34 FACTORS AFFECTING ACCURACY AND PRECISION OF A MEASURING SYSTEM • A measuring system is made of five basic elements. These are: 1. Standard 2. Work piece 3. Instrument 4. Person 5. Environment
- 33. FACTORS AFFECTING ACCURACY OF A MEASURING SYSTEM 1. Standard Coefficient of thermal expansion Stability with time Elastic properties Position etc 2. Work piece: Cleanliness surface finish etc. Surface defects Hidden geometry 3. Instrument Inadequate amplification Scale error Deformation while handling heavy w/p Calibration error Readability and Repeatability 35
- 34. 34 4. Person Training skill Sense of precision appreciation Ability to select measuring instrument & standard Attitude towards personal accuracy achievement Planning for measurement technique to have minimum just with consistent in precision 5. Environment Temperature, pressure and humidity Clean surrounding and minimum vibration Adequate illumination Temperature equalization between standard w/p & instrument Higher accuracy can be achieved if all 5 factors are considered, analysed & steps are taken to eliminate them FACTORS AFFECTING ACCURACY OF A MEASURING SYSTEM
- 35. 35 What is Error in Measurement? • Measurement Error (Observational Error) is the difference between a measured(actual) value and its true value. • True size Theoretical size of a dimension which is free from errors. • Actual size size obtained through measurement with permissible error. ERRORS IN MEASUREMENT
- 36. Types of Errors in Measurements Gross / Blunder Errors Measurement Errors Systematic Errors Instrumental Errors Observational Errors Environmental Errors Theoretical Errors Random Errors TYPES OF ERRORS IN MEASUREMENT
- 37. 37 1) Gross or Blunder Errors: This category of errors includes all the human mistakes while reading, recording the readings. The best example of these errors is a person or operator reading pressure gauge 1.01N/m2 as 1.10N/m2 2) Measurement Error: The measurement error is the result of the variation of a measurement of the true value Usually, Measurement error consists of a random error and systematic error. TYPES OF ERRORS IN MEASUREMENT
- 38. 38 a. Systematic Error (Controllable Error) • A systematic error is a constant error that under the same operating conditions. • Systematic error is caused by any factors that systematically affect measurement . • Classification of systematic errors: i. Instrumental Errors – Calibration Error ii. Environmental Errors – Temp, Pressure, Humidity iii. Observational Errors - Parallax iv. Theoretical - Percentage
- 39. 39 Random Errors (Uncontrollable Error) • Random (or indeterminate) errors are caused by uncontrollable fluctuations in variables that affect experimental results. • Random errors are caused by the sudden change in experimental conditions and noise and tiredness in the working persons. These errors are either positive or negative. • These errors may be reduced by taking the average of a large number of readings.