Downloaded 694 times
More Related Content
![[PPT] on Steam Turbine](https://cdn.slidesharecdn.com/ss_thumbnails/spsharmafinalppt-140608082156-phpapp01-thumbnail.jpg?width=640&height=640&fit=bounds)
Similar to BOILER MOUNTINGS & ACCESSORIES
BOILER MOUNTINGS & ACCESSORIES
- 1. Sardar Vallbhbhai PatelInstitute of Technology Vasad Active Learning Assesment Title:- Boiler Mounting & Accessories.. Faculty name:-J.M.Panchal Student Name:- (1) Shah Smit (2) Zala Rishabh (3) Panchal Bhavik (4) Prajapati Parthiv
- 2.
- 3. BOILER MOUNTINGS • Mainlyseven (7) mountings are required and essential to a Boiler : 1. Water level indicator. (Water gauge) 2. Main steam stop valve. 3. Pressure gauge. 4. Feed check valve. 5. Fusible plug. 6. Blow down valve. (Blow off cock) 7. Safety valve.
- 4. Blow-Off Cock Function: The functionof blow-off cock is to discharge mud and other sediments deposited in the bottom most part of the water space in the boiler, while boiler is in operation. It can also be used to drain-off boiler water. Hence it is mounted at the lowest part of the boiler. When it is open, water under the pressure rushes out, thus carrying sediments and mud.
- 5. Working • When rectangularhole of plug is brought in line with casing hole by rotating spindle, the water flow out. When the solid portion of the plug is in front of casing hole (this position shown in the fig.) the water cannot flow out of boiler.
- 6. Fusible plug • Function: It is use to protect the boil against damage due to overheating caused by low water level in the boiler.
- 7. Working • In normalworking condition, the upper surface of fusible plug is covered with water which keeps the temperature of the plug below its melting point while other end of plug is exposed to fire or hot gases. The low melting point (tin or lead) does not melt till the upper surface of plug is submerged in water. But in case of water level in boiler falls below the danger levels, the fusible plug uncovered by the water and get exposed to steam. This overheats the plug and the fusible metal having low melting point which melts quickly. Thus the third plug drops down and second hollow gun became open, the steam rushes into the furnace and puts out the fire (stop).
- 8. Feed check valve •Function: It controls the supply of water from the boiler when the feed pump pressure is less than boiler pressure or pump is stopped.
- 9. WORKING Inlet and outletpipe of valve expose different pressure .at inlet of valve the feed pump pressure acts and outlet pipe of the valve the boiler pressure act . When feed pump is in operation, The pressure on the feed pump side(inlet) is more than pressure on the boiler side(outlet).This pressure difference lifts the non return valve, And allows water flow into boiler.
- 10. WATER LEVEL INDICATOR Function:- Itindicate the water level inside the boiler vessel. It shows the level in the boiler drum.
- 11. WORKING • When steamcock and water cock opened, steam rushes from upper passage and water rushed from lower from passage to the glass tube. This will indicate the level of water in the boiler. Two ball are places at the junction of metal tube. Under normal operating condition the ball are kept. full line circle in case the glass tube is broken, steam will rushes from upper passage and water from lower passage due to pressure difference between boiler pressure at atmospheric pressure. the ball are carrier along the passage to and of glass tube and then closed passages. This position of ball sown in fig by dotted circle. Thus flow of water and steam out of boiler is prevented.
- 12. Steam Stop Valve •Function:-It regulate the flow of steam from boiler to the steam pipe or from one steam pipe to the other.
- 13. WORKING • The spindleit rotated by help of hand wheel due to rotation of spindle the valve move up and down. When the valve sits over the valve seat, the passage of steam is completely closed. The steam passage may be partially or fully opened by moving the valve up, help of rotating the hand wheel the clearance (passage) between valve and valve seat regulates the flow of steam out of boilers. in locomotive boilers, the supply of the steam is regulated by means of a regulator which is placed inside boiler cell and operated by a handle from driver’s cabin.
- 14. Pressure Gauge • Function: It indicates the pressure of steam in boiler.
- 15. Working • When pressureis applied to inside of oval bourdon tube. It cross section tends to becomes circular, and free end of bourdon tube try to becomes straight, so turning the spindle by the links and gearing. This causes the needle to move and indicate pressure on graduated dial.
- 16. Safety valves • Function: Safety valves are located on the top of the boiler. They guard the boiler against the excessive high pressure of steam inside the drum. If the pressure of steam in the boiler drum exceeds the working pressure then the safety valve allows blow-off the excess quantity of steam to atmosphere. Thus the pressure of steam in the drum falls. The escape of steam makes a audio noise to warm the boiler attendant.
- 17. Safety valves :There arefour types of safety valve: 1. Dead weight safety valve. 2. Spring loaded safety valve 3. Lever loaded safety valve 4. High steam and low water safety valve
- 18. Dead weight safetyvalve
- 19. Lever safety valve •The main disadvantages of dead weight safety valve as heavy weights required for high pressure boiler is eliminated in a lever safety valve by use of a lever.
- 20. Spring loaded safetyvalve • There are various types of spring loaded safety valve use on different boilers.
- 21. High steam &low water safety valve
- 22. Function 1) The steamautomatically escapes out when the level of water falls below a normal level. 2) It automatically discharges the excess steam when the pressure of steam rises above a normal pressure. This valve is generally used in Cornish or Lancashire boiler.
- 23.
- 24. :Boilers Accessories: :are asunder: (1) Feed pump (2) Injector (3) Economiser (4) Air preheater (5) Superheater (6) Steam separator (7) Steam trap
- 25. Feed Pump • Function: •The feed pump is a pump which is used to deliver feed water to the boiler. • Double feed pump is commonly employed for medium size boilers.
- 26. Types of Feedpumps There are Three types of feed Pumps mainly: Reciprocating pumps-simplex,duplex,Triplex Rotary pumps Centrifugal pumps
- 27. Reciprocating Duplex Pump Duplexpump is very common steam driven reciprocating pump. It consist of two steam cylinder placed side by side. There are two steam ports for each of the cylinders.
- 28. Injector Fucntion : Injectoris used to feed water in the boiler . It is commonly employees for vertical boiler and does not find its application in large capacity high pressure boilers . it also uses more space is not available for the installation for feed pump.
- 29. Economiser Function: Economiser increasesthe temperature of feed water using waste of heat to flue gases leaving the boiler through chimney.
- 30. Construction and working: Economiserconsist of a large vertical cast iron or steel water pipes,one end of vertical pipes is connected with vertivcal pipes A and other end with B. Hot flue gases from boiler pass over the vertical tubes .The heat transfer take place from flue gases to cold water rising in vertical tubes
- 31. Super heater • Thefunction of super heater is to increase the temperature of the steam above its saturation point.
- 32. Working • To superheatthe steam generated by boiler. • Super heaters are heat exchangers in which heat is transferred to the saturated steam to increase its temperature. • Superheated steam has the following advantages : i) Steam consumption of the engine or turbine is reduced. ii) Losses due to condensation in the cylinders and the steam pipes are reduced. iii)Erosion of turbine blade is eliminated. iv) Efficiency of steam plant is increased
- 33. Steam Separator A Steamseparator, sometimes referred to as a moisture separator, is a device for separating water droplets from steam. The simplest type of steam separator is the steam dome on a steam locomotive. Stationary boilers and nuclear reactors may have more complex devices which impart a "spin" to the steam so that water droplets are thrown outwards by centrifugal force and collected.
- 34. Steam Trap: :: Asteam trap is a device used to discharge condensate and non condensable gases with a negligible consumption or loss of live steam. Most steam traps are nothing more than automatic valves. They open, close or modulate automatically. Others, like venture traps, are based on turbulent 2-phase flows to obstruct the steam flow.::
- 35. Air Preheater • Anair preheater is a general term to describe any device designed to heat air before another process (for example, combustion in a boiler) with the primary objective of increasing the thermal efficiency of the process. They may be used alone or to replace a recuperative heat system or to replace a steam coil.