Case Study on Highway Geometry for Two Lane Highway

International Research Journal of Engineering and Technology (IRJET) e-ISSN: 2395-0056
Volume: 09 Issue: 09 | Sep 2022 www.irjet.net p-ISSN: 2395-0072
© 2022, IRJET | Impact Factor value: 7.529 | ISO 9001:2008 Certified Journal | Page 550
Case Study on Highway Geometry for Two Lane Highway
Amit S. Chame 1, Dr. M.R. Vyawahare2, Prof. A.R. Bijwe 3
1 Student, Dr. Rajendra Gode Institute of Technology & Research, Amravati, Maharashtra, India.
2,3 Prof., Dept. of civil Engineering, Dr. Rajendra Gode Institute of Technology & Research, Amravati, Maharashtra,
India.
---------------------------------------------------------------------***---------------------------------------------------------------------
Abstract - In India, due to rapid growth in vehicular traffic,
it is very important to construct safe highways. While
constructing highways, geometric design is very important in
highway design, it can be greatly used to reduce road
accidents significantly.
Geometric design elements consist of carriageway, median,
horizontal and vertical curves, lane width, shoulder width,
superelevation, curve radius, sight distance, etc. Based on
previous studies had shown that sharp curve or short sigh
distance results in higher accident problem, therefore these
issues should be accounted in designand developingstage. Itis
important to plan and design the geometric elementsatinitial
stage taking into consideration of future growth and also the
cost otherwise it will be becoming more expensive or very
difficult to construct as surrounding area gets developed. The
research would help to identify design issues in geometric
design and to find out accidental prone areas where most
accidents likely to happen.
Key Words: Carriageway, median width, Pavement
width, Horizontal Curve, Vertical Curve, Intersection.
1. INTRODUCTION
While designing any highway, it is important to study the
geometric design elements and one must have guidelines,
standards and specification to developed the highway with
maximum safety. The geometric design of a highway deals
with visible features of road consists of cross section of
roads, median width, intersection, horizontal & vertical
curve, sight distance etc. Below isthebriefdefinitionofsome
geometric elements.
Cross Section: The cross section of highway shows the
vehicle, bicycle lanes, sidewalks/footpaths along with their
cross slope. Generally, cross sections show features or
roadside facility and type of road with layers.
Shoulder: It is the part of formation width except carriage
ways. They are used by the vehicular traffic as the
emergency lanes or sometimes as service lanes.
Median: Median separates the opposite traffic and provides
safety features as well as reduces headlight glare, improve
comfort for night driving. Two types of mediansprovided on
highways as per requirement i.e., raised and depressed
median.
Camber: Cross slope can be defined as the slope of a
roadway perpendicular to the centre line. If a road were
completely level, water would drain off it. Three types of
camber are straight camber, parabolic camber and mixed
camber.
Superelevation: The outer edge of the road with respect of
the inner edge of road is raised, this is called superelevation.
It is very important to provide at horizontal curve tosmooth
passage of vehicle.
Horizontal Curve: A horizontal highway curve is a plan to
provide a change in direction in the centre line along the
highway. Horizontal alignment includes the design of
horizontal curves, super elevation, transitionlengths,speed,
extra widening. Simple curve, compound curve, reverse
curve and spiral curve these are the types of horizontal
curve.
Vertical curve: Vertical curve are provided to change the
slope in the road. Sag/valley curve and summit curvearethe
types of vertical curve.
Sight Distance: Sight distancelengthofroadislengthvisible
ahead the driver at any instance. Stopping sight distance
(SSD), Overtaking sight distance (OSD) and Intermediate
sight distance (ISD) are the types of sight distance.
2.OBJECTIVE
 The main objective of the study is to examined
the existing geometry of highway.
 To identify the safety issue in highway design
and accidental prone area of highway
 To providethe simple geometric design tomeet
all expectation of road users like pedestrian,
bicycle, motorist etc at reasonable cost.
3. LITERATURE REVIEW
In past periods many studies have been done on geometric
design elements of roadtoimproveroadsafetyandoptimum
efficiency of use. The study will help to minimize the errors
occurring roadway design which is helpful for the system to
avoid future cost and difficulties with improved traffic
operation.

Ali Aram (2010). He presented studyoftwo-lanehighwayon
horizontal curve. He stated that horizontal curve has higher
crash rates rather than straight sectionofcomparablelength
and traffic structure. The increase in crash rates become
particularly important at radii below 200 m.
Zhang Yingxue (2009), stated that it is important for traffic
accident to bring high accident rate if the sight distance is
not enough and this is visible on the places where have the
bad visual distance of small horizontal curve radius, small
crest vertical curve radius, intersection, and lack of
overtaking sight distance on some road section. In order to
ensure traffic safety, the traveling sight distance should be
design enough when design horizontal orvertical alignment.
Vikas golakot (2018) his thesis included that the aim of his
study is to find the role of the geometric factors of road on
accident rate in the case of plain terrain and also find the
extent to which these factors affecttheaccidentrateforrural
areas. The study aims to find the impact of factors like extra
widening, horizontal radius, sight distance, K-value, super
elevation, horizontal arc length, vertical arc length, vertical
gradient on the accident rate and aims to study the
significant factors causing accidents and to find the values
for future design of roads.
Indian Road Congress SP 73: 2015. It gives the specification
and standards for two laning highways provide guidelines
like types of terrain classification, right of way, different
types of cross section, design speed for different types of
traffic and geometric elements. The policy includes vertical
clearance, structure cross section & capacity of bridges and
about tunnels.
4. METHODOLGY
It is proposed to study for the national highway starting
from chainage at 19+300 km near Piliv village (Latitude of
19°82'400"N and Longitude of 54°47'55"E.) and end at 31+
700 km near Tandulwadi (Latitude of 19°70'95"N and
Longitude of 54°27'73"E.) in Maharashtra State. Various
factors are studied and verifying with the relevant
specification and standards. Detailed primary data for the
selected road iscollectedfromcompanies/organizations and
verifications of the designed parameters with respect to IRC
provisions.
5. DATA ANALYSIS
The plan and profile design drawings and the data collected,
are thoroughly studied visited site for selected project, and
analysed based on the proposed methodology. Following
observations were noted:
 Project stretch is located in Solapur District of
Maharashtra state, India.
 The length of the project stretch is around 12.4 km.
 The project stretch is shown in map with reference
of Maharashtra and India Map.
 The terrain of road through which it passingisplain
terrain.
 Design of Typical cross section- The typical cross
section for the road project stretch is designed over
the horizontal alignment and presented as below
Fig -1: Typical Cross Section
 Justification with IRC provision - proposed key
elements are checked with the IRC provisions to
validate the design, the same are mentioned as
below,
Table -1: IRC Validations
Items IRC Provision Remarks
Carriage -
way
IRC SP 73 2015, Carriage way 7
mtr [Fig 2.2, Page No 20]
Followed
Shoulder
IRC SP 73 2015, Shoulder 1.5 mtr
for paved shoulder 2 mtr for
earthen shoulder [Clause No 2.6,
Page No 10]
Followed
Camber
IRC SP 73 2015, Crossfall on
straight section, 2% for cement
concrete surface [Clause No 2.8,
Page No 12]
Followed
Design
speed
Minimum design speed for plain
and rolling terrain 80 Kmph
where ruling speed is 100 Kmph
[Clause No 2.2, Page No 10]
Followed
Horizontal Curve: The horizontal alignment data based on
the plan and profile is analysed step by step and the
observation related to each design element is recorded.

Table -2: Horizontal Curve Radius with Speed
Sr
No
Chainage Curve
Radius
Remarks
From To
1 19+450 19+530 250 m
80 Kmph
(Maximum
speed)
2 19+710 19+760 250 m
80 Kmph
(Maximum
speed)
3 20+550 20+730 250 m
80 Kmph
(Maximum
speed) Need to
upgrade/Realign
ment.
4 22+880 22+930 250 m
80 Kmph
(Maximum
speed)
Vertical Curve: The vertical curve data based on the plan
and profile is analysed step by step and the observation
related to each design element is recorded.
Table -3: Vertical Curve Radius with Type and Length.
Junction geometry: The general design principles of
intersection design also include design of the approach
speed and restriction on the available land. Following
Observation are recorded at major intersections at Ch.
27+150, Ch. 31+600 and minor junction at Ch. 21+450 and
Ch. 22+800.
 Layout at major intersections is not channelized
which is a major safety issue, hence the to make
traffic flow effective these intersections to be
channelized.
 Visibility at junction location in approaches is a
safety deficiency which is need to be designed for
junction approaches and also need to maintain.
 Proper Sign boards are provided at location.
6. CONCLUSIONS
Following conclusions can be made from the research;
 Geometric design guidelines encouragemoresafety
and comfort for road users, so it is very important
to design accordingly specification and standards.
 More care should be taken at curve locations as
more accidents likely to happen at theses location
while designing highway.
 Carriageway, camber, shoulder and design speed
are found in order in selected stretch with respect
to IRC Provisions.
 The study would be helpful to examine the existing
geometry of highway and can be used to improveor
enhance the efficiency of road users.
REFERENCES
[1] IRC SP 73 2015- “Manual of Specifications & Standards
for Two-laning of Highways”.
[2] Yagmur ozinal, Islam Gokalp, Yigit Katanalp, Volkan
Emre Uz, 2019. “A literature review on design of
geometric elements of the roundabouts”.
[3] Council, F., and Steward, J.R., " Safety Effects of the
Conversion of Two-Lane Rural to Four-Lane Rural
Roadways Based on Cross-Sectional Models ",
Transportation Research Board Annual Meeting, 2000.
[4] Hameed Aswad Mohammed ,04 July 2013. “THE
INFLUENCE OF ROAD GEOMETRIC DESIGN ELEMENTS
ON HIGHWAY SAFETY” (IJCIET).
[5] Vikas Golakoti (2015), “STUDY OF GEOMETRIC
FEATURES OF ROAD AND ACCIDENT RATE”.
[6] Zhang Yingxue, "Analysis of the Relation between
Highway Horizontal Curve and Traffic Safety",
International Conference on Measuring Technologyand
Mechatronics Automation, China, 2009.
[7] Rishabh Chourasia, 2020. “Case Study on the Effect of
Geometric Design Consistency on Level of Safety for
Rural Roads under Indian Conditions”
[8] Ali Aram (2010), “Effective safety factors on Horizontal
curves of Two-Lane Highways” Journal of Applied
Sciences 10 (22), Malaysia, P.P 2814-2822, 2010.
[9] Pankaj M. Thakare, Vipul S. Bawner, 2018. “Computer-
Aided Geometric Design of Road and Safety Evaluation
Using Vehicle Simulation Model”.
[10] Kuldeep Kalita, Akhilesh K. Maurya, 2019. “Probabilistic
Geometric Design of Highways: A Review”.
Sr No Chainage Type of curve Remarks
1 20+419 Summit 300 mt length
2 21+462 Summit 385 mt length
3 21+831 Valley 145 mt length

Case Study on Highway Geometry for Two Lane Highway

More Related Content

Similar to Case Study on Highway Geometry for Two Lane Highway

More from IRJET Journal

Recently uploaded

Case Study on Highway Geometry for Two Lane Highway