Download to read offline
![www.studentyogi.com www.studentyogi.com
Code No: R05310402
Set No. 1
III B.Tech I Semester Regular Examinations, November 2007
DIGITAL IC APPLICATIONS
( Common to Electronics & Communication Engineering and Electronics &
Instrumentation Engineering)
Time: 3 hours Max Marks: 80
Answer any FIVE Questions
All Questions carry equal marks
1. (a) What are the parameters that are necessary to de ne the electrical charac-
teristics of CMOS circuits? Mention the typical values of a CMOS NAND
gate.
(b) Design a CMOS 4-input AND-OR-INVERT gate. Draw the logic diagram and
function table. [8+8]
2. (a) Mention the DC noise margin levels of ECL 10K family.
(b) A single pull-up resistor to +5V is used to provide a constant-1 logic source
to 15 di erent 74LS00 inputs. What is the maximum value of this resistor?
How much high state DC noise margin can be provided in this case? [6+10]
3. (a) Write a VHDL Entity and Architecture for a 3-bit synchronous counter using
Flip-Flops.
(b) Explain the use of Packages. Give the syntax and structure of a package in
VHDL. [8+8]
4. Design a logic circuit to detect prime number of a 5-bit input. Write the structural
VHDL program for the same. [16]
5. Design a 10 to 4 enco der with inputs 1- out of ?10 co de and outputs in BCD?
Provide the data ow style VHDL program? [16]
6. Write VHDL program for 1-bit comparator circuit with the input bits and equal,
grater than and less than inputs from the previous stage and the outputs contain
equal, greater than and less than conditions. Using this entity write VHDL program
for 16-bit comparator using data ow style. Do not use any additional logic for this
purpose. [16]
7. (a) Di erentiate between ripple counter and synchronous counter? Design a 4-bit
counter in both modes and estimate the propagation delay.
(b) Design a modulo-88 counter using 74X163 Ics. [8+8]
8. (a) Explain the necessity of two-dimensional deco ding mechanism in memories.
Draw MOS transistor memory cell in ROM and explain the operation.
(b) Determine the ROM size needed to realize the logic function performed by
74×153 and 74×139. [8+8]](https://image.slidesharecdn.com/digital-ic-applicationsjntumodelpaperwww-studentyogi-com-100113225313-phpapp02/75/D-I-G-I-T-A-L-I-C-A-P-P-L-I-C-A-T-I-O-N-S-J-N-T-U-M-O-D-E-L-P-A-P-E-R-Www-1-2048.jpg)
![www.studentyogi.com www.studentyogi.com
Code No: R05310402
Set No. 2
III B.Tech I Semester Regular Examinations, November 2007
DIGITAL IC APPLICATIONS
( Common to Electronics & Communication Engineering and Electronics &
Instrumentation Engineering)
Time: 3 hours Max Marks: 80
Answer any FIVE Questions
All Questions carry equal marks
1. (a) Explain how to estimate sinking current for low output and sourcing current
for high output of CMOS gate.
(b) Analyze the fall time of CMOS inverter output with L = 100 L = 2 5 L =
10 . Assume L as stable state voltage. [8+8]
2. (a) Draw the circuit diagram of basic TTL NAND gate and explain the three
parts with the help of functional operation.
(b) Explain sinking current and sourcing current of TTL output. Which of the
above parameters decide the fan-out and how? [8+8]
3. (a) Write a VHDL Entity and Architecture for the following function?
F(x) = a b c
Also draw the relevant logic diagram.
(b) Explain the use of Packages Give the syntax and structure of a package in
VHDL [8+8]
4. Design the logic circuit and write a data- ow style VHDL program for the following
functions.
(a) ( ) = SA,B,C,D (0 2 5 7 8 10 13 15) + (1 6 11)
(b) ( ) = A,B,C,D (1 4 5 7 9 11 12 13 15))
[8+8]
5. With the help of logic diagram explain 74×157 multiplexer? Write the data ow
style VHDL program for this IC? [16]
6. Design a 24-bit comparator circuit using 74×682 ICs and discuss the functionality
of the circuit. Also implement VHDL source co de in data ow style. [16]
7. (a) Distinguish between latch and ip- op. Show the logic diagram for both.
Explain the operation with the help of function table.
(b) Design a Mo dulo-12 ripple counter using 74×74? Write a VHDL program for
this logic using data ow style. [8+8]
8. (a) Discuss how PROM, EPROM and EEPROM technologies di er from each
other.](https://image.slidesharecdn.com/digital-ic-applicationsjntumodelpaperwww-studentyogi-com-100113225313-phpapp02/75/D-I-G-I-T-A-L-I-C-A-P-P-L-I-C-A-T-I-O-N-S-J-N-T-U-M-O-D-E-L-P-A-P-E-R-Www-2-2048.jpg)
![www.studentyogi.com www.studentyogi.com
Code No: R05310402
Set No. 2
(b) With the help of timing waveforms, explain read and write operations of
SRAM. [8+8]](https://image.slidesharecdn.com/digital-ic-applicationsjntumodelpaperwww-studentyogi-com-100113225313-phpapp02/75/D-I-G-I-T-A-L-I-C-A-P-P-L-I-C-A-T-I-O-N-S-J-N-T-U-M-O-D-E-L-P-A-P-E-R-Www-3-2048.jpg)
![www.studentyogi.com www.studentyogi.com
Code No: R05310402
Set No. 3
III B.Tech I Semester Regular Examinations, November 2007
DIGITAL IC APPLICATIONS
( Common to Electronics & Communication Engineering and Electronics &
Instrumentation Engineering)
Time: 3 hours Max Marks: 80
Answer any FIVE Questions
All Questions carry equal marks
1. (a) Design CMOS transistor circuit for 3-input AND gate. With the help of
function table explain the operation of the circuit diagram.
(b) Design a CMOS transistor circuit that has the functional behavior as
( ) = (a + b) (b + c)(a + c)
Also draw the relevant circuit diagrams. [8+8]
2. (a) Explain the following terms with reference to TTL gate.
i. Voltage levels for logic ‘1’ & logic ‘0’
ii. DC Noise margin
iii. Low-state unit load
iv. High-state fan-out
(b) Design a transistor circuit of 2-input ECL NOR gate. Explain the operation
with the help of function table. [8+8]
3. Explain with an example the syntax and the function of the following VHDL state-
ments.
(a) Process statement
(b) If, else and elseif statements
(c) Case statement
(d) Lo op statement [4×4=16]
4. Design a logic circuit to detect prime number of a 5-bit input. Write the structural
VHDL program for the same. [16]
5. (a) It is necessary to identify the position of mechanical disk, when rotates with
a step of 450. Give the necessary encoding mechanism and draw the logic
circuit?
(b) Using two 74×138 deco ders design a 4 to 16 decoder. [16]
6. (a) Write a VHDL program for the circuit that counts number of Ones in a 16-bit
register using structural style of modeling.
(b) Design a 4×4 combinational multiplier and the write the necessary VHDL](https://image.slidesharecdn.com/digital-ic-applicationsjntumodelpaperwww-studentyogi-com-100113225313-phpapp02/75/D-I-G-I-T-A-L-I-C-A-P-P-L-I-C-A-T-I-O-N-S-J-N-T-U-M-O-D-E-L-P-A-P-E-R-Www-4-2048.jpg)
![www.studentyogi.com www.studentyogi.com
Code No: R05310402
Set No. 3
7. Show the logic diagram of 74×175 IC and write VHDL program for this IC in data
ow style. Using this entity develop the program for 16-bit register and show the
corresponding circuit also explain how the register is cleared? [16]
8. (a) Draw the basic cell structure of Dynamic RAM. What is the necessity of
refresh cycle? Explain the timing requirements of refresh operation.
(b) Discuss in detail ROM access mechanism with the help of timing waveforms.
[8+8]](https://image.slidesharecdn.com/digital-ic-applicationsjntumodelpaperwww-studentyogi-com-100113225313-phpapp02/75/D-I-G-I-T-A-L-I-C-A-P-P-L-I-C-A-T-I-O-N-S-J-N-T-U-M-O-D-E-L-P-A-P-E-R-Www-5-2048.jpg)
![www.studentyogi.com www.studentyogi.com
Code No: R05310402
Set No. 4
III B.Tech I Semester Regular Examinations, November 2007
DIGITAL IC APPLICATIONS
( Common to Electronics & Communication Engineering and Electronics &
Instrumentation Engineering)
Time: 3 hours Max Marks: 80
Answer any FIVE Questions
All Questions carry equal marks
1. (a) Design CMOS transistor circuit for 3-input AND gate. With the help of
function table explain the operation of the circuit diagram.
(b) Design a CMOS transistor circuit that has the functional behavior as
( ) = (a + b) (b + c)(a + c)
Also draw the relevant circuit diagrams. [8+8]
2. (a) Design a transistor circuit of 2-input ECL NOR gate. Explain the operation
with the help of function table.
(b) A single pull-up resistor to +5V is used to provide a constant-1 logic source
to 15 di erent 74LS00 inputs. What is the maximum value of this resistor?
How much high state DC noise margin can be provided in this case? [8+8]
3. (a) Explain the various data types supported by VHDL. Give the necessary ex-
amples.
(b) Discuss the case statement and its use in the VHDL program. [8+8]
4. Design a logic circuit to detect prime number of a 5-bit input. Write the structural
VHDL program for the same. [16]
5. Design a two-digit BCD adder with logic gates. Using this logic write the VHDL
program. In structural style of modeling. [8+8]
6. Design a combinational logic circuit that counts the number of ones in a 24-bit
register. Write a VHDL program for the same using structural style or modeling.
[16]
7. (a) Draw the logic diagram of 74×163 binary counter and explain its operation.
(b) Design a modulo-100 counter using two 74×163 binary counters? [8+8]
8. (a) Design an 8×4 diode ROM using 74×138 for the following data starting from
the rst location.
6901
(b) How many ROM bits are required to build a 16-bit adder/subtractor with
mode control, carry input, carry output and two’s complement over ow out-
put. Show the block schematic with all inputs and outputs. [8+8]](https://image.slidesharecdn.com/digital-ic-applicationsjntumodelpaperwww-studentyogi-com-100113225313-phpapp02/75/D-I-G-I-T-A-L-I-C-A-P-P-L-I-C-A-T-I-O-N-S-J-N-T-U-M-O-D-E-L-P-A-P-E-R-Www-6-2048.jpg)
More Related Content
Similar to D I G I T A L I C A P P L I C A T I O N S J N T U M O D E L P A P E R{Www
D I G I T A L I C A P P L I C A T I O N S J N T U M O D E L P A P E R{Www
- 1. www.studentyogi.com www.studentyogi.com Code No: R05310402 Set No. 1 III B.Tech I Semester Regular Examinations, November 2007 DIGITAL IC APPLICATIONS ( Common to Electronics & Communication Engineering and Electronics & Instrumentation Engineering) Time: 3 hours Max Marks: 80 Answer any FIVE Questions All Questions carry equal marks 1. (a) What are the parameters that are necessary to de ne the electrical charac- teristics of CMOS circuits? Mention the typical values of a CMOS NAND gate. (b) Design a CMOS 4-input AND-OR-INVERT gate. Draw the logic diagram and function table. [8+8] 2. (a) Mention the DC noise margin levels of ECL 10K family. (b) A single pull-up resistor to +5V is used to provide a constant-1 logic source to 15 di erent 74LS00 inputs. What is the maximum value of this resistor? How much high state DC noise margin can be provided in this case? [6+10] 3. (a) Write a VHDL Entity and Architecture for a 3-bit synchronous counter using Flip-Flops. (b) Explain the use of Packages. Give the syntax and structure of a package in VHDL. [8+8] 4. Design a logic circuit to detect prime number of a 5-bit input. Write the structural VHDL program for the same. [16] 5. Design a 10 to 4 enco der with inputs 1- out of ?10 co de and outputs in BCD? Provide the data ow style VHDL program? [16] 6. Write VHDL program for 1-bit comparator circuit with the input bits and equal, grater than and less than inputs from the previous stage and the outputs contain equal, greater than and less than conditions. Using this entity write VHDL program for 16-bit comparator using data ow style. Do not use any additional logic for this purpose. [16] 7. (a) Di erentiate between ripple counter and synchronous counter? Design a 4-bit counter in both modes and estimate the propagation delay. (b) Design a modulo-88 counter using 74X163 Ics. [8+8] 8. (a) Explain the necessity of two-dimensional deco ding mechanism in memories. Draw MOS transistor memory cell in ROM and explain the operation. (b) Determine the ROM size needed to realize the logic function performed by 74×153 and 74×139. [8+8]
- 2. www.studentyogi.com www.studentyogi.com Code No: R05310402 Set No. 2 III B.Tech I Semester Regular Examinations, November 2007 DIGITAL IC APPLICATIONS ( Common to Electronics & Communication Engineering and Electronics & Instrumentation Engineering) Time: 3 hours Max Marks: 80 Answer any FIVE Questions All Questions carry equal marks 1. (a) Explain how to estimate sinking current for low output and sourcing current for high output of CMOS gate. (b) Analyze the fall time of CMOS inverter output with L = 100 L = 2 5 L = 10 . Assume L as stable state voltage. [8+8] 2. (a) Draw the circuit diagram of basic TTL NAND gate and explain the three parts with the help of functional operation. (b) Explain sinking current and sourcing current of TTL output. Which of the above parameters decide the fan-out and how? [8+8] 3. (a) Write a VHDL Entity and Architecture for the following function? F(x) = a b c Also draw the relevant logic diagram. (b) Explain the use of Packages Give the syntax and structure of a package in VHDL [8+8] 4. Design the logic circuit and write a data- ow style VHDL program for the following functions. (a) ( ) = SA,B,C,D (0 2 5 7 8 10 13 15) + (1 6 11) (b) ( ) = A,B,C,D (1 4 5 7 9 11 12 13 15)) [8+8] 5. With the help of logic diagram explain 74×157 multiplexer? Write the data ow style VHDL program for this IC? [16] 6. Design a 24-bit comparator circuit using 74×682 ICs and discuss the functionality of the circuit. Also implement VHDL source co de in data ow style. [16] 7. (a) Distinguish between latch and ip- op. Show the logic diagram for both. Explain the operation with the help of function table. (b) Design a Mo dulo-12 ripple counter using 74×74? Write a VHDL program for this logic using data ow style. [8+8] 8. (a) Discuss how PROM, EPROM and EEPROM technologies di er from each other.
- 3. www.studentyogi.com www.studentyogi.com Code No: R05310402 Set No. 2 (b) With the help of timing waveforms, explain read and write operations of SRAM. [8+8]
- 4. www.studentyogi.com www.studentyogi.com Code No: R05310402 Set No. 3 III B.Tech I Semester Regular Examinations, November 2007 DIGITAL IC APPLICATIONS ( Common to Electronics & Communication Engineering and Electronics & Instrumentation Engineering) Time: 3 hours Max Marks: 80 Answer any FIVE Questions All Questions carry equal marks 1. (a) Design CMOS transistor circuit for 3-input AND gate. With the help of function table explain the operation of the circuit diagram. (b) Design a CMOS transistor circuit that has the functional behavior as ( ) = (a + b) (b + c)(a + c) Also draw the relevant circuit diagrams. [8+8] 2. (a) Explain the following terms with reference to TTL gate. i. Voltage levels for logic ‘1’ & logic ‘0’ ii. DC Noise margin iii. Low-state unit load iv. High-state fan-out (b) Design a transistor circuit of 2-input ECL NOR gate. Explain the operation with the help of function table. [8+8] 3. Explain with an example the syntax and the function of the following VHDL state- ments. (a) Process statement (b) If, else and elseif statements (c) Case statement (d) Lo op statement [4×4=16] 4. Design a logic circuit to detect prime number of a 5-bit input. Write the structural VHDL program for the same. [16] 5. (a) It is necessary to identify the position of mechanical disk, when rotates with a step of 450. Give the necessary encoding mechanism and draw the logic circuit? (b) Using two 74×138 deco ders design a 4 to 16 decoder. [16] 6. (a) Write a VHDL program for the circuit that counts number of Ones in a 16-bit register using structural style of modeling. (b) Design a 4×4 combinational multiplier and the write the necessary VHDL
- 5. www.studentyogi.com www.studentyogi.com Code No: R05310402 Set No. 3 7. Show the logic diagram of 74×175 IC and write VHDL program for this IC in data ow style. Using this entity develop the program for 16-bit register and show the corresponding circuit also explain how the register is cleared? [16] 8. (a) Draw the basic cell structure of Dynamic RAM. What is the necessity of refresh cycle? Explain the timing requirements of refresh operation. (b) Discuss in detail ROM access mechanism with the help of timing waveforms. [8+8]
- 6. www.studentyogi.com www.studentyogi.com Code No: R05310402 Set No. 4 III B.Tech I Semester Regular Examinations, November 2007 DIGITAL IC APPLICATIONS ( Common to Electronics & Communication Engineering and Electronics & Instrumentation Engineering) Time: 3 hours Max Marks: 80 Answer any FIVE Questions All Questions carry equal marks 1. (a) Design CMOS transistor circuit for 3-input AND gate. With the help of function table explain the operation of the circuit diagram. (b) Design a CMOS transistor circuit that has the functional behavior as ( ) = (a + b) (b + c)(a + c) Also draw the relevant circuit diagrams. [8+8] 2. (a) Design a transistor circuit of 2-input ECL NOR gate. Explain the operation with the help of function table. (b) A single pull-up resistor to +5V is used to provide a constant-1 logic source to 15 di erent 74LS00 inputs. What is the maximum value of this resistor? How much high state DC noise margin can be provided in this case? [8+8] 3. (a) Explain the various data types supported by VHDL. Give the necessary ex- amples. (b) Discuss the case statement and its use in the VHDL program. [8+8] 4. Design a logic circuit to detect prime number of a 5-bit input. Write the structural VHDL program for the same. [16] 5. Design a two-digit BCD adder with logic gates. Using this logic write the VHDL program. In structural style of modeling. [8+8] 6. Design a combinational logic circuit that counts the number of ones in a 24-bit register. Write a VHDL program for the same using structural style or modeling. [16] 7. (a) Draw the logic diagram of 74×163 binary counter and explain its operation. (b) Design a modulo-100 counter using two 74×163 binary counters? [8+8] 8. (a) Design an 8×4 diode ROM using 74×138 for the following data starting from the rst location. 6901 (b) How many ROM bits are required to build a 16-bit adder/subtractor with mode control, carry input, carry output and two’s complement over ow out- put. Show the block schematic with all inputs and outputs. [8+8]