Download to read offline
dc-dc choppers, power electronics, types of chopers and their working.
- 1. 1 Advanced Power Electronics EEE-814 Unit5: DC Choppers (DC-DC CONVERTERS)
- 2. Introduction • Chopper isa static device. • A variable dc voltage is obtained from a constant dc voltage source. • Also known as dc-to-dc converter. • Widely used for motor control. • Also used in regenerative braking. • Thyristor converter offers greater efficiency, faster response, lower maintenance, smaller • size and smooth control.
- 3. Types of Choppers Step-downchoppers (BUCK CONVERTERS) Step-up choppers. (BOOST CONVERTERS) In step down chopper output voltage is less than input voltage. In step up chopper output voltage is more than input voltage.
- 4. Principle of Step- downChopper • A step-down chopper with resistive load. • The thyristor in the circuit acts as a switch. • When thyristor is ON, supply voltage appears across the load • When thyristor is OFF, the voltage across the load will be zero.
- 5.
- 6. Methods of Control •The output dc voltage can be varied by the following methods. • Pulse width modulation control or constant frequency operation. • Variable frequency control.
- 7. Step-down Chopper with RLLoad • When chopper is ON, supply is connected across load. • Current flows from supply to the load. • When chopper is OFF, load current continues to flow in the same direction through FWD due to energy stored in inductor ‘L’. • Load current can be continuous or discontinuous depending on the values of ‘L’and duty cycle ‘d’ • For a continuous current operation, load current varies between two limits Imax and Imin • When current becomes equal to Imax the chopper is turned-off and it is turned-on when current reduces to Imin.
- 8. Expressions For LoadCurrent i0 For Continuous Current Operation When Chopper Is ON (0 <t <tON)
- 9.
- 12. RMS value ofoutput current
- 13. Principle of Step-upChopper •Step up chopper is used to obtain a load voltage higher than the input voltage V The values of L and C are chosen depending upon the requirement of output voltage and current. •When the chopper is ON, the inductor L is connected across the supply. •The inductor current ‘ rises and the inductor stores energy during the ON time of the chopper, t ON • When the chopper is off, the inductor current Iis forced to flow through the diode D and load for a period, tOFF. • The current tends to decrease resulting in reversing the polarity of induced EMF in L. • Therefore, voltage across load is given by A large capacitor ‘C’ connected across the load, will provide a continuous output voltage Diode D prevents any current flow from capacitor to the source.
- 14. Expression For OutputVoltage
- 15. Performance Parameters • Thethyristor requires a certain minimum time to turn ON and turn OFF. • Duty cycle d can be varied only between a min. & max. value, limiting the min. and max. value of the output voltage. • Ripple in the load current depends inversely on the chopping frequency, f. • To reduce the load ripple current, frequency should be as high as possible.
- 16. Classification of Choppers •Choppersare classified as •–Class A Chopper •–Class B Chopper •–Class C Chopper •–Class D Chopper •–Class E Chopper
- 17. Class A Chopper •When chopper is ON, supply voltage V is connected across the load. • When chopper is OFF, v O = 0 and the load Current continues to flow in the same direction through the FWD. • The average values of output voltage and current are always positive. • Class A Chopper is a first quadrant chopper . • Class A Chopper is a step-down chopper in which power always flows form source to load. • It is used to control the speed of dc motor. • The output current equations obtained in step down chopper with R-Lload can be used to study the performance of Class A Chopper.
- 18. Class B Choppers •When chopper is ON, E drives a current • through L and R in a direction opposite to that shown in figure. • During the ON period of the chopper, the inductance L stores energy. • When Chopper is OFF, diode D conducts, and part of the energy stored in inductor L is returned to the supply. • Average output voltage is positive. • Average output current is negative. • Therefore, Class B Chopper operates in second quadrant. • In this chopper, power flows from load to source. • Class B Chopper is used for regenerative braking of dc motor. • Class B Chopper is a step-up chopper.
- 19.
- 20. Expression for OutputCurrent
- 21. Expression for theoutput current cont…
- 22. Application: Regenerative BrakingSystem • Regenerative braking systems (RBSs) are a type of kinetic energy recovery system that transfers the kinetic energy of an object in motion into potential or stored energy to slow the vehicle down, and as a result increases fuel efficiency. These systems are also called kinetic energy recovery systems.
- 23. Class C Choppers •Class C Chopper is a combination of Class A and Class B Choppers. • For first quadrant operation, CH1 is ON or D2 conducts. • For second quadrant operation, CH2 is ON or D1 conducts. • When CH1is ON, the load current is positive. • The output voltage is equal to ‘V’ & the load receives power from the source. • When CH1is turned OFF, energy stored in inductance L forces current to flow through the diode D2 and the output voltage is zero. • Current continues to flow in positive direction. •When CH2is triggered, the voltage Eforces current to flow in opposite direction through L and CH2. •The output voltage is zero. •On turning OFF CH2, the energy stored in the inductance drives current through diode D1 and the supply •Output voltage is V; the input current becomes negative and power flows from load to source. •Average output voltage is positive •Average output current can take both positive and negative values. •Choppers CH1& CH2should not be turned ON simultaneously as it would result in short circuiting the supply. •Class C Choppercan be used both for dc motor control and regenerative braking of dc motor. •Class C Choppercan be used as a step-up or step-down chopper. VOLTAGE IS ALWAYS POSITIVE BUT THE CURRENT CAN BE NEGATIVE AND POSITIVE
- 24. Class C ChoppersCont…
- 25. Modes of Working:Graphical 1st Quadrant 2nd Quadrant
- 26. Applications • Motor Controland Regenerative Braking Systems (RBSs)
- 27. Class D Choppers •Class D is a two-quadrant chopper. • When both CH 1 and CH 2 are triggered simultaneously, the output voltage v O = V and output current flows through the load. • When CH 1 and CH 2 are turned OFF, the load current continues to flow in the same direction through load, D 1 and D 2 , due to the energy stored in the inductor L. • Output voltage v0= V •Average load voltage is positive if chopper ON time is more than the OFF time •Average output voltage becomes negative if tON< tOFF. •Hence the direction of load current is always positive, but load voltage can be positive or negative.
- 28.
- 29.
- 30.
- 31. Class E Choppers Class Eis a four-quadrant chopper When CH 1 and CH 4 are triggered, output current i O flows in positive direction through CH 1 and CH 4 , and with output voltage v O = V . This gives the first quadrant operation. When both CH 1 and CH 4 are OFF, the energy stored in the inductor L drives i O through D 2 and D 3 in the same direction, but output voltage v O = V Therefore, the chopper operates in the fourth quadrant. When CH2and CH3are triggered, the load current iO flows in opposite direction & output voltage vO= -V. Since both iO and vO are negative, the chopper operates in third quadrant. When both CH2and CH3are OFF, the load current Io continues to flow in the same direction D1andD4and the output voltage vO= V. Therefore, the chopper operates in second quadrant as vO is positive but iO is negative. Parallel Combination of two class C choppers
- 32. Modes of working1st Quadrant: When CH1 and CH2 ON 4th Quadrant: When CH1 and CH2 OFF 3rd Quadrant: When CH3 and CH2 ON 3rd Quadrant: When CH3 and CH2 OFF
- 33. IMPORTANT Points Step downchopper: when inductor polarity is opposing the source Step up chopper: when inductor polarity is same as the source
- 34.
- 35.
- 48. 48 Steady State EquivalentCircuit Modelling
- 52. The DC T/FModel
- 58.
- 59. Diode Equivalent Circuits/DiodeModels • It is a combination of elements that represents the actual terminal characteristics of a device in its operating region • Diode models are mathematical models used to approximate the actual behaviour of real diodes for analysis purposes. • The diode circuits are solved by using diode models in the place of diodes without affecting the system behaviour
- 60. Why diode models •Diode’s V-I characteristics is nonlinear • nonlinearity complicates the calculations in circuits involving diodes • Use of diode models or equivalent circuits enables the use of conventional circuit analysis techniques
- 61. Ideal diode model •It is the least accurate approximation • It is represented by a simple switch • An ideal forward-biased diode acts like a closed (on) switch • An ideal reversed-biased diode acts like an open (off) switch • The barrier potential, the forward dynamic resistance, and the reverse current are neglected • Diode is replaced by simple switch • These models are used in troubleshooting, to determine whether the diode is working properly and where the exact values of voltage or current are not needed
- 63. Simplified Diode model/Practicaldiode model • The practical model includes the barrier potential • It states that a forward-biased silicon diode under dc condition has a voltage drop (cut-in voltage) of 0.7 V (for Si diodes) across it at any level of diode current within the rated values • It consists of a voltage source representing the cut-in voltage of the diode and an ideal diode acting as a switch
- 64.
- 65. Circuit with idealdiode
- 66. Forward bias • forwardcurrent is determined as follows by applying Kirchhoff’s voltage law
- 67. Reverse bias • diodeis assumed to have zero reverse current
- 68. Piecewise model • Thismodel approximates the characteristics of the device by straight-line segments • But straight-line segments do not result in an exact duplication of the actual characteristics, especially in the knee region • This model approximates the diode characteristic curve as a series of linear segments • In mathematics, piecewise means taking a function and breaking it down into several linear segments
- 69.
- 70. • This modelcontains a voltage source representing the cut-in voltage and diode resistance (rav) • Battery (0.7V) specifies the voltage across the device must be greater than the threshold battery voltage before conduction through the device in the direction • When conduction is established the resistance of the diode is the specified value of rav.
- 71. • approximate levelof rav can be determined from a specified operating point on the specification sheet • For a silicon semiconductor diode, if IF =10 mA at VD =0.8 V, for silicon that a shift of 0.7 V is required before the characteristics rise
- 72.
- 76.
- 77.
- 82. 82 Power And Harmonicsin Nonsinusoidal Systems