![Using Macaulay’s Method to Solve the Situation of Simply Supported Beam
with Concentrated Load
x
W
W/2 x W/2
L/2
x
Mx = W/2 x - W [x – L/2]
E I d2
y/dx2
= W/2 x - W [x – L/2]
E I dy/dx = W/4 x2
- W [x – L/2]2
+ A
2
E I y = W x3
- W [x – L/2]3
+ A x + B
12 6](https://image.slidesharecdn.com/iv-defonbeamppt-250129095052-d859aac8/85/DEFLECTION-ON-BEAM-IN-STRENGTH-OF-MATERIALS-17-320.jpg)
![Boundary Conditions
At x = 0 , y = 0 i.e. B = 0
At x = 0, y = 0
i.e. 0 = WL3
- W [L – L/2]3
+ AL
12 6
0 = = WL3
- W L3
+ AL
12 48
A = WL2
- WL2
= - WL2
48 12 16
E I y = W x3
- W [x – L/2]3
- WL2
x
12 6 16
Ymax occurs at x = L/2
i.e. E I y = W [L3
) - WL2
[L]
12 8 16 2
Y max = - W L3
48 EI](https://image.slidesharecdn.com/iv-defonbeamppt-250129095052-d859aac8/85/DEFLECTION-ON-BEAM-IN-STRENGTH-OF-MATERIALS-18-320.jpg)
![Macaulay’s Method for u.d.l.s
Example: Determine the deflection of the beam at x = 3 (middle of Beam) if E =
210 kN mm-2
. The Cross-Section is given as below. 50 mm
x
15kN 5 kN/m 10
10 80
x
1m RA = 36kN 5 m RB =9 kN
Taking Moment about B: 15 x 6 - 5 RA + (5 x 6 ) x 3 = 0
RA = 36 kN
RB = 15 + (5 x 6) - 36 = 9 kN
EI d2
y/dx2
= - 15 x + 36 [x – 1 ] - 5 x2
/2
EI dy/dx = - 15/2 x2
+ 36/2 [x – 1]2
– 5/6 x3
+ A
E I y = - 15/6 x3
+ 36/6 [x – 1]3
- 5/24 x4
+ A x + B
EI y = - 2.5 x3
+ 6 [x-1]3
- 0.2083 x4
+ A x + B](https://image.slidesharecdn.com/iv-defonbeamppt-250129095052-d859aac8/85/DEFLECTION-ON-BEAM-IN-STRENGTH-OF-MATERIALS-19-320.jpg)
![Boundary Conditions
At x = 1, y = 0
i.e. 0 = - 2.5 - 0.21 + A + B
i.e. A + B = 2.5 + 0.2083 = 2.71 ……….. (1)
Also: At x = 6, y = 0
i.e. 0 = - 540 + 750 - 272.16 + 6 A + B
i.e . 6A + B = 60 ------------- (2)
From Equations (1) and (2), A = 11.45 and B = - 8.75
i.e. E I y = - 2.5 x3
+ 6 [x – 1]3
- 0.2083 x4
+ 11.46 x - 8.75
At x = 3 , EI y = (- 2.5 x 27) + 48 - 16.87 + 34.38 - 8.75
= - 10.74](https://image.slidesharecdn.com/iv-defonbeamppt-250129095052-d859aac8/85/DEFLECTION-ON-BEAM-IN-STRENGTH-OF-MATERIALS-20-320.jpg)
DEFLECTION ON BEAM IN STRENGTH OF MATERIALS
- 2. DEFLECTION OF BEAMS When a beam with a straight longitudinal axis is loaded by lateral forces, the axis is deformed into a curve, called the deflection curve of the beam. Deflection is the displacement in the y direction of any point on the axis of the beam. See Figure 5.1 below. P A y A B x v
- 3. Deflection of Beams Contd. •The calculation of deflections is an important part of structural analysis and design. • Deflections are essential for example in the analysis of statically indeterminate structures and in dynamic analysis, as when investigating the vibration of aircraft or response of buildings to earthquakes. • Deflections are sometimes calculated in order to verify that they are within tolerable limits.
- 4. 5.1 RELATIONSHIP BETWEEN LOADING, SHEAR FORCE, BENDING MOMENT, SLOPE AND DEFLECTION. Consider a beam AB which is initially horizontal when unloaded. If it deflects to a new position A ‘ B’ under load, the slope at any point C is: i = dy/dx
- 5. Basic Differential Equation For Deflection This is usually very small in practice, and for small curvatures: ds = dx = R di (Figure 5.2). di/dx = 1/R But i = dy/dx Therefore: d2 y/dx2 = 1/R ……………….. (1) Now from simple bending theory: M/I = E/R 1/R = M/EI Therefore substituting in equation (1): M = E I d2 y/dx2 ………………………………. (2) This is the basic differential equation for the deflection of beams.
- 12. Direct Integration Method Contd. • In Some cases, it is not convenient to commence the integration procedure with the bending moment equation since this may be difficult to obtain. In such cases, it is often more convenient to commence with the equation for the loading at the general point XX of the beam. A typical example follows:
- 14. Macaulay’s Method •The Macaulay’s method involves the general method of obtaining slopes and deflections (i.e. integrating the equation for M) will still apply provided that the term, W (x – a) is integrated with respect to (x – a) and not x.
- 15. Example of Using Macaulay’s Method for Concentrated loads
- 16. Example Contd.
- 17. Using Macaulay’s Method to Solve the Situation of Simply Supported Beam with Concentrated Load x W W/2 x W/2 L/2 x Mx = W/2 x - W [x – L/2] E I d2 y/dx2 = W/2 x - W [x – L/2] E I dy/dx = W/4 x2 - W [x – L/2]2 + A 2 E I y = W x3 - W [x – L/2]3 + A x + B 12 6
- 18. Boundary Conditions At x = 0 , y = 0 i.e. B = 0 At x = 0, y = 0 i.e. 0 = WL3 - W [L – L/2]3 + AL 12 6 0 = = WL3 - W L3 + AL 12 48 A = WL2 - WL2 = - WL2 48 12 16 E I y = W x3 - W [x – L/2]3 - WL2 x 12 6 16 Ymax occurs at x = L/2 i.e. E I y = W [L3 ) - WL2 [L] 12 8 16 2 Y max = - W L3 48 EI
- 19. Macaulay’s Method for u.d.l.s Example: Determine the deflection of the beam at x = 3 (middle of Beam) if E = 210 kN mm-2 . The Cross-Section is given as below. 50 mm x 15kN 5 kN/m 10 10 80 x 1m RA = 36kN 5 m RB =9 kN Taking Moment about B: 15 x 6 - 5 RA + (5 x 6 ) x 3 = 0 RA = 36 kN RB = 15 + (5 x 6) - 36 = 9 kN EI d2 y/dx2 = - 15 x + 36 [x – 1 ] - 5 x2 /2 EI dy/dx = - 15/2 x2 + 36/2 [x – 1]2 – 5/6 x3 + A E I y = - 15/6 x3 + 36/6 [x – 1]3 - 5/24 x4 + A x + B EI y = - 2.5 x3 + 6 [x-1]3 - 0.2083 x4 + A x + B
- 20. Boundary Conditions At x = 1, y = 0 i.e. 0 = - 2.5 - 0.21 + A + B i.e. A + B = 2.5 + 0.2083 = 2.71 ……….. (1) Also: At x = 6, y = 0 i.e. 0 = - 540 + 750 - 272.16 + 6 A + B i.e . 6A + B = 60 ------------- (2) From Equations (1) and (2), A = 11.45 and B = - 8.75 i.e. E I y = - 2.5 x3 + 6 [x – 1]3 - 0.2083 x4 + 11.46 x - 8.75 At x = 3 , EI y = (- 2.5 x 27) + 48 - 16.87 + 34.38 - 8.75 = - 10.74
- 21. Solution Concluded M o m e n t o f I n e r t ia o f g iv e n s e c t io n a b o u t t h e n e u t r a l a x is = 2 5 0 1 0 1 2 5 0 0 4 5 1 0 8 0 1 2 2 4 6 1 0 3 2 3 6 4 x x x x m L N M O Q P . y k N m E I k N m x k N m x x m 1 0 7 4 1 0 7 4 2 1 0 1 0 2 4 6 1 0 3 3 6 2 6 4 . . / . = 0 . 0 2 0 7 9 m = 2 0 . 7 9 m m
- 22. Mohr’s Area-Moment Method •The Mohr area-moment procedure can be summarised as: •If A and B are two points on the deflection curve of a beam, EI is constant and B is a point of zero slope, then the Mohr’s theorems state that: •(1) Slope at A = 1/EI x area of B.M. diagram between A and B •(2) Deflection at A relative to B = 1/EI x first moment of area of B.M diagram between A and B about A.