Drager Flame 2300 - Fixed Flame Detector - Spec Sheet

Drager Flame 2300 - Fixed Flame Detector - Spec Sheet

• 1.
  Simple installation andcommissioning Installation is simple! The detector is ea-sily installed with a stainless steel moun-ting bracket; this can be rotated to ensure optimum positioning of the detector in re-lation to the potential fire source. Angular markings allow the positioning angles of the detector to be recorded for future reference. Detector flexibility As well as a 4 to 20 mA output and 3 re-lays, an optional RS 485 output is also available, which can be multi-dropped to a central location. This provides a number of options for detector monitoring and the triggering of the necessary control action upon the detection of a fire. Automatic and manual optics checks Au to matic checks of the detector electro-nics and optics ensure no fault goes un-detected. Additionally the test can be trig-gered manually at anytime. Isolated 4 to 20 mA as standard Complete flexibility enables the detector to be operated from a separate power supply (as a 4 wire device) or as a 3 wire device where there is no requirement for an isolated output. Easily visible status LED A tri-coloured LED which is visible at the front of the detector provides a simple sta-tus indication to personnel in close proxi-mity to the detector. Green indicates nor-mal operation; yellow indicates a fault and red indicates the presence of radiation. False alarm immunity The Dräger Flame 2300 provides the hig-hest level of false alarm immunity. This is because the detector requires both IR and UV sensors to alarm before the de-tector will itself output an alarm condition and such action ensures that false alarms are all but non-existent. Worldwide Approvals The Dräger Flame 2300 can be used worldwide with the following approvals: ATEX, IECEx, FM and CSA. Dräger Flame 2300 ST-326-2008 ST-341-2004 The Dräger Flame 2300 is an explosion proof combined UVIR flame detector used for the detection of hydrocarbon based fires. The detector provides flexibility with its numerous output modes, and advanced design features ensure reliability in the detection of fires whilst at the same time providing excellent immunity to potential false alarm sources. Dräger Flame 2300: Explosion proof combined UVIR flame detector for hydrocarbon based fires ST-474-2004 Tel: +44 (0)191 490 1547 Fax: +44 (0)191 477 5371 Email: [email protected] Website: www.heattracing.co.uk www.thorneanderrick.co.uk
• 2.
  Dräger Flame 2300,Al housing, M20 entries 23 50 424 Dräger Flame 2300, Al housing, M25 entries 23 50 430 Dräger Flame 2300, Al housing, 1/2” NPT entries 23 50 436 Dräger Flame 2300, Al housing, 3/4” NPT entries 23 50 442 Dräger Flame 2300, SS housing, M20 entries 23 50 427 Dräger Flame 2300, SS housing, M25 entries 23 50 433 Dräger Flame 2300, SS housing, 1/2” NPT entries 23 50 439 Dräger Flame 2300, SS housing, 3/4” NPT entries 23 50 445 TECHNICAL DATA Type Explosion proof UVIR flame detector for hydrocarbon based fires Spectral response IR 4.2 to 4.7 micron, UV 0.185 to 0.26 micron Field of view Horizontal 90°, vertical 90° Sensitivity 0.1 m2 gasoline fire at 18 metres, 1 sq. foot fire at 60 feet Response time t90 3.3 seconds, typical; configurable up to 30 seconds Signal output Fault 0 mA Optics/electronics check failure 2 mA Normal operation 4 mA IR presence 8 mA UV presence 12 mA Fire pre-warning 16 mA Fire 20 mA (factory configurable for latching/non-latching alarm) 3 relays for fault, alarm and accessory, ratings 125 VAC, 0.5 A; 30 VDC, 2 A optional RS 485 Supply voltage 18 to 32 VDC, current consumption 175 mA quiescent state at 24 VDC Ambient conditions Temperature - 40 to + 70 °C, - 40 to + 158 °F Pressure 915 to 1055 hPa, 27.9 to 31.2 inch of Hg Humidity 0 to 99 %RH, non condensing Enclosure IP 66 / NEMA 4X Cable entry M20, M25, 1/2” NPT or 3/4” NPT Size (L x D, approx.) 275 mm x 155 mm, 10.8” x 6.1” Weight (approx.) 3.5 kg, 7.7 lbs Approvals ATEX II 2G EEx d IIC T6/T5 ; - 50 ≤ Tamb ≤ + 60 / + 70 °C IECEx Ex d IIC T6/T5 ; - 50 ≤ Tamb ≤ + 60 / + 70 °C FM/CSA Class I, Groups A, B, C, D Class I, Zone 1, Groups IIA, IIB & IIC Ex d II C; T6/T5; - 40 ≤ Tamb ≤ + 60 / + 70°C Tel: +44 (0)191 490 1547 Fax: +44 (0)191 477 5371 Email: [email protected] Website: www.heattracing.co.uk www.thorneanderrick.co.uk