ir_auto_12

ir_auto_12

• 1.
  Automation Engineer withfive years and four months of experience Automation. Expertise with MITSUBISHI, SIEMENS,CODESYS, MESSUNG,ABB,ALLEN BRADLEY & DELTA PLC, HMI, SCADA, AC & DC DRIVES, and other Automation Devices. Application Development (PLC,HMI & SCADA Programming and Maintenance), Installation, Technical Support , Problem Management & Resolution for new & existing systems for Industrial , Food & Beverages and Building Automation & Control Systems, Application Software development, Technical Support, Problem management & resolution for new & existing systems for different industries.  TAG AUTOMATION Noida, up.  DURATION : 02 JULY 2011 TO TILL DATE  DESIGNATION : TAG AUTOMATION,NOIDA  DESIGNATION : PROJECT CUM SERVICE ENGINEER.   PLC & SCADA programming according to machine function and its process.  PLC & SCADA based machine troubleshooting and maintenance.  Installation and commissioning of PLC & SCADA system.  AC & DC Drives installation, testing and troubleshooting.  Panel installation Installation,testing and troubeshooting.  Panel designing with concept on load management.  Control panel designing and its troubleshooting on the basic on fault present in panel at that time.  Control valves and module Installation, programming, loop checking, module simulation using current and voltage sources in PLC.  Complete Electrical Installation, HMI & PLC application software development, servicing and commissioning of different Project according to customer requirement.  Automatic TMT line commessioning with Rotary shear.Automation done with SIEMENCE PLC S7 1200 and WINCC Professional version (SCADA).  Commessioning of Block Motor(1000HP) with DC Drive and PLC MITSUBISHI FX 3G.  Commessioning of Automatic HOT Shearing machine ,Air Compressor machine ,Transporter,Over Head Crane,Cooling Tower ,TMT Line Cutting Machine,Lifting Table etc.  Maintenance of all electrical and electronics equipment. Email:- [email protected] [email protected] Address:- NEW ASHOK NAGAR, A-76, FIRST FLOOR, NEW DELHI-110096 IRFAN HASHMI Contact: +91-7004429462 +91-9334198187  CARRIER OBJECTIVE  CURRENT WORKING EXPERIENCE  RESPONSIBILITIES
• 2.
   SCADA monitoringand ALARM handling and its troubleshooting on the basic of real time fault present at that time.  Providing technical support and documentation (ELECTRICAL DRAWING).  Monitoring and prepare daily report and report to management including.  STAR DELTA motor starter & DOL starter based circuit designing, implementation and control these circuit by this PLC.  Discuss with customers during implementation and understanding complicated problems resulted in successful issue resolution.  Programming of PLC ,SCADA , HMI and DRIVES on the basic live project.  Troubleshooting on PLC based Panel and included system.  Fault finding and its troubleshooting.  PLC LADDER LOGIC modification. Company Name Project 1) INDIA YAMAHA MOTORS PVT LTD, SURAJPUR, GREATER NOIDA, UP.  Programming & commissioning of press machine.  Programming and Installation of HMI in machine.  Programming of MIG welding machine with SCADA & Panel installation. Etc. 2) I CAT (INTENATIONAL CENTER FOR AUTOMOTIVE TECHNOLOGY) IMT MANESAR, GURGAON.  HVAC Control according to required temperature and humidity by PLC.  Installation of HMI for monitor system temperature and humidity and show running process message of the system.  If system contain any fault then fault message show on HMI with buzzer.  If any DPS and Damper faulty then HMI show fault message with alarm and buzzer. 3) DMRC (DELHI METRO RAIL CORP) DWARKA METRO DEPO & YAMUNA DEPO.  Programming & commissioning of PLC (Analog Modules), HMI & Ac Drive system for MOTOR TESTING machine in dwarka depo.  Troubleshooting & modification in PLC programming in automatic METRO Washing Machine in yamuna dep. 4) NSW PVT LTD, HERO HONDA CHOWK, GURGAON.  PLC Programming of Micro oven and installation of SCADA system.  Installation of HMI for operator interface.  PLC program modification. Etc. 5) AVR ENTERPRISES LIMITED, INDUSTRIAL AREA, KANPUR.  Programming and commissioning of textile machine (Extender machine).  Installation of HMI for operator interface.  Installation of AC Drive and testing. Etc. 6) JOY_D_ZINE PVT LTD, MUNDKA NEW DELHI.  Programming of Book binding machine.  Installation of HMI for Alarm and operator interface with machine.  PROJECT DONE IN COMPANIES
• 3.
  7) REVA ENGINEERING NEWDELHI  Programming & commissioning of PLC, HMI & AC DRIVE for Automatic Bricks & CEMENT Blocks system machine.  Maintenance & PLC Logic Modification according to Machine requirement. 8) U-CAL FUEL AUTO PVT LTD, BAWAL, HARIYANA.  Programming & commissioning of PLC & SCADA system for fuel system testing machine.  Troubleshooting & modification in PLC programming .Etc. 9) RSWM UDAIPUR, RAJISTHAN.  Programming modification and Troubleshooting in Spinning Machine.  Installation of SERVO AMPLIFIER & MOTOR and its programming according to Function. 10) DCM TEXTILE HISAR, HARIYANA.  Programming and installation of SERVO AMPLIFIER & MOTOR and its programming according to Function.  Installation of PLC & HMI for SERVO AMPLIFIER & MOTOR . 11) MALHOTRA RUBBER SURAJPUR, GREATER NOIDA. UP.  Programming and installation of PLC, HMI & AC DRIVE and its programming for TYRE TESTING machine.  Auto sheet cutting machine Programming according to desire length put into the HMI to PLC. 12) SEBROS AUTO PVT LTD IMT MANESAR,GURGAON,HARIYANA  Installation and programming of PLC , HMI and AC Drive for PRESS Machine.  Maintenance and PLC program modification. 13) SADHU FORGING FARIDABAD, HARIYANA.  Installation and programming of PLC , HMI and AC Drive for BAND SAW Machine.  Maintenance and PLC program modification. 14) FAITH ENGINEERING TAIGORE GARDEN NEW DELHI  Installation and programming of PLC , HMI and AC Drive for BLOW MOULDING Machine.  Maintenance and PLC program modification.  Three days training on Mitsubishi Q-Series PLC of PLC Hardware and Programming at Mitsubishi Electric, INDIA, GURGAON.  Four days training on Mitsubishi Communication module as CC-link, MELSEC-net, ETHERNET.  Two days Seminar on Mitsubishi Electric India for Technical meet & L series PLC launching.  Two days training of programming on MESSUNG’s NEXGEN & NEXGENIE PLC on CoDeSys software a MESSUNG GURGAON.  Two days technical meet in Hotel Country Inn, for presentation of project and new product launching.  ACADEMIC QUALIFICATIONS:  WORKSHOPS & SEMINAR Course School/College University / Board % of Marks B.E. (ECE) MACET , Patna MAGADH University 77.5 Intermediate Oriental College ,Patna BIEC 58.9 Matriculation Dr Zakir hussain,Patna BSEB 65.6
• 4.
  Operating System :Window XP, Windows 7, Windows 8 , 8.1 & 10. MS Office : MS Word, Excel, Power point. FATHER’S NAME : Md Rahman Hashmi MOTHER’S NAME : Nazma Khatoon DATE OF BIRTH : Jan 15, 1988 LANGUAGE KNOWN : Hindi, English, and Urdu NATIONALITY : Indian PERMANENT ADRESS : Dargah Road, Neemtal, PO-Mahendru Patna 800006 PASSPORT NO : J3374575 DATE OF ISSUE : 29/06/2010 DATE OF EXPIRY : 28/06/2020 PLACE OF ISSUE : PATNA I hereby declare that all the information stated in this RESUME is true to the best of my knowledge and belief till date. PLC (programming logic controller) Plc. models:- Mitsubishi,SIEMENS, Allen Bradley , ABB.  Selection of plc. According to project requirement (I/O’ s).  Programming of PLC, wiring & Commissioning of PLC. HMI (Human machine interference) HMI model:- SMART TOUCH,GOT 1000(Mitsubishi), Beiger, SMART LINE  Creating application in HMI as per requirement.  Creating graph ,Historical trends, Alarm, Alarm history, message display  Input outputs monitoring.  Machine fault display SCADA Wonderware :- WINCC FLEXIBLE,WINCC Professional, Intouch , Indo Soft, ELLIPSE (Creating new applications, animation, communication with PLC ) Ac Drives  Installation, Controlling, Programming parameters.  Communication with HMI & PLC. Process Instrumentation Proximity sensors, Photo sensor, laser sensor( temperature detection),LVDT, RTD, Thermocouple, Flow transmitter , Pressure Transducers, Level Sensors, Load cell , Encoder. Switch Gears Relay, Contactor, MCB, MCCB, Circuit Breakers. (all switch gear which use in control wiring)  PROFESSIONAL SKILL’S in “INDUSTRIAL AUTOMATION”  HARDWARE & SOFTWARE PLATFORMS  PERSONAL PROFILE  DECLARATION Place: New Delhi Date: (IRFAN HASHMI)  PASSPORT DETAILS