IRJET- Structural Behaviour of Concrete Beam using Non Biodegradable Materials

International Research Journal of Engineering and Technology (IRJET) e-ISSN: 2395-0056
Volume: 06 Issue: 02 | Feb 2019 www.irjet.net p-ISSN: 2395-0072
© 2019, IRJET | Impact Factor value: 7.211 | ISO 9001:2008 Certified Journal | Page 1633
STRUCTURAL BEHAVIOUR OF CONCRETE BEAM USING NON
BIODEGRADABLE MATERIALS
PRABHU. R1, Er. RAVI .C2
1Student, M.E Structural Engineering, Oxford Engineering College, Tiruchirappalli, Tamil Nadu, India
2Professor & Head, Department of Civil Engineering, Oxford Engineering College, Tiruchirappalli,
Tamil Nadu, India
---------------------------------------------------------------------***----------------------------------------------------------------------
Abstract - The Material which does not decompose into
the soil and causes the soil to pollute is called as NBD
materials which are abbreviated as Non Bio Degradable
materials. These will prevent the supply of oxygen, nitrogen
etc., to the micro-organisms presents in the soil and make it
a barren land. In order to prevent such mechanism these
materials should be used in a proper way there by making it
eco-friendly. Here in this project plastic fibre obtained from
cement bags are chipped based on the aspect ratio based
added in concrete by using such fibre in the construction
helps in clean construction site. In this project Cylinders,
Prisms, and Cubes of standard dimensions have been made
to introduce NBD Fibers with various mix ratio as 1%, 2%,
3%, 4%. Various tests are conducted to find the property of
the NBD Concrete materials. The Main tests such as
Compressive Strength for Concrete and Flexural Strength of
Concrete have been conducted. On comparing the results of
NBD Fiber Concrete with that of Conventional Concrete, 3%
additionally Adding of NBD fibers showed Maximum
Compressive strength of concrete value at 28 days is 25%
increase compared with in Conventional Concrete and
Maximum Flexural Strength of Concrete value at 28 days is
55% increase compared with in Conventional Concrete.
During Phase II, Mechanical Properties like Split tensile
Strength and Durability properties of NBD Fibers will be
discussed.
Key Words: NBD Concrete, NBD Fiber, Compressive
Strength, Flexural Strength.
1. INTRODUCTION
Concrete is a versatile material for civil
engineering building construction. It has ability to get cast
in any different type of form and shape. All basic
ingredients of concrete are natural origin. But the
properties of concrete can be changed by adding some
special natural or artificial ingredients.
The Concrete has many advantageous properties
such as good compressive strength, durability,
impermeability and fire resistance. However the concrete
has some better properties like as weak in tension,
brittleness, less resistance to cracking, lower impact
strength, heavy weight, etc. Some remedial measures can
be taken to minimize these more better properties of
concrete. The some of the better properties of concrete are
due to micro cracks at mortar aggregate interface. The
addition of fibers in concrete would act as crack inhibitors
and substantially improve the tensile strength, cracking
resistance, impact strength, wear and tear, fatigue
resistance and ductility of concrete.
1.1 NON BIODEGRADABLE MATERIALS (NBD):
The definition of non-biodegradable is the direct
opposite of the word biodegradable. When something is
biodegradable that means that its components are able to
be broken down with the influence of microorganisms
after it is discarded into the environment. Non-
biodegradable is defined as that the components of the
item will not break down over time. An example of a non-
biodegradable item would be a tire, Polythene
sheets/covers, disposable plastic glasses, syringes, cement
bags etc. The nature of decomposition of various materials
is given in the following table.
Table -1: Decomposition of Various Waste Materials
Type of
Small waste
Approximate
time taken to
degenerate
Nature of
material
Peels of
vegetable
and leaves
1 to 2 weeks. Biodegradable
Paper 10–30 days Biodegradable
Cotton cloth 2 to 5 months Biodegradable
Plastic bags Several years
Non-
biodegradable
1.2 CLASSIFICATION OF FIBRES:
A fibre may be defined as a flexible, macroscopically
homogenous body having a high ratio of length to width
and a small cross-section. On the basis of their origin,
fibres are classified as follows
Natural fibres are those derived naturally from the
animal, vegetable and mineral kingdoms. These include
cotton, linen, hemp, jute and ramie all obtained from
vegetable cellulose; wool, mohair, vicuna from animal; and
asbestos from minerals.
Synthetic fibres are manufactured from natural
organic fibres, synthetic organic polymers and inorganic

substances. Included in this category are: rayon, acetate,
azlon based on natural organic polymers; acrylic, aramid,
nylon, olefin, polyester, vinyon based on synthetic
polymers, and glass, metallic fibres, ceramics based on
inorganic substances.
2. PROPERTIES OF CONCRETE MATERIALS
2.1 CEMENT
The Cement used for this study is Portland
Pozzolona Cement as per IS Requirements. The
requirements of the properties of all these cements are
given the following Indian Standards. IS: 12269 - 1987 (53
Grade), IS: 8112- 989 (43 Grade), IS 269 - 1989 (33Grade).
In this Project Work the Ultra Tech Cement PPC is
selected.
Table-2: Properties of Cement
Physical Property Value
Consistency 29%
Initial Setting Time 34 Minutes
Final Setting Time 340 Minutes
Specific Gravity 3.04
2.2 FINE AGGREGATES
Fine Aggregates are material passing through an
IS sieve that is less than 4.75 mm gauge beyond which
they are known as a coarse aggregate. Coarse aggregate
form the main matrix of the Concrete, whereas fine
Aggregates form the filler matrix between the coarse
aggregate. The most important function of the fine
Aggregates is to provide workability and uniformity in the
mixture. In this project work, Grade I Fine Aggregates of
particle size less than 2 mm and greater than 1 mm are
chosen.
Table -3: Properties of Fine Aggregates
Fineness Modules 2.733
2.3 COARSE AGGREGATES
Coarse Aggregates are material passing through
an IS sieve that is greater than 4.75 mm gauge beyond
which they are known as a coarse aggregate. The most
important function of the coarse aggregates is to provide
workability and uniformity in the mixture. According to IS
383: 1970 the coarse aggregates is being classified based
on the shape. The shapes are Rounded, Irregular, Angular,
and Flaky. The Aggregates are available is different size
are 40 mm, 20 mm, 10 mm, and 4.75 mm respectively.
In this project work, Coarse Aggregates Shape and
Size is Crushed Angular Aggregates in 20 mm size are
chosen.
Table -4: Properties of Fine Aggregates
Fineness Modules 6.13
2.4 NBD FIBERS
A fibre may be defined as a flexible,
macroscopically homogenous body having a high ratio of
length to width and a small cross-section. On the basis of
their origin. Fibers are classified as reinforced plastics falls
into two classes:
Short Fibers are also called as discontinuous fibers, with a
general aspect ratio (defined as the ratio of fibers length to
diameter) between20 to 60.
Long Fibers, is means of continuous fibers, the general
aspect ratio is between 200 to 500.
Polypropylene
Polypropylene is a 100% Synthetic Fiber which is
transformer from 85% propylene. The monomer of
polypropylene is propylene.
 Polypropylene is a by-product of petroleum
 It is available 3 different sizes i.e. 6mm, 12mm,
24mm
 In the present investigation 12mm is used.
Fig .1: NBD Fibers from Cement Bags
Fig .2: Polypropylene Fibers

3. RESULTS AND DISCUSSIONS
3.1 COMPRESSIVE STRENGTH OF CONCRETE
CUBE
Compressive strength is the capacity of the
material to withstand axially directed pushing forces. It
provides data of forces versus deformation for the
conditions of the test method. When the limit of
Compressive strength of concrete is reached, brittle
materials are crushed. It is calculated using following
formula
Compressive Strength
Compressive Strength of Concrete Cube = Load / Area
Unit of Compressive Strength is N/mm2
Table -5: Compressive Strength of Concrete
% OF
ADDITION
OF FIBER
7th DAY
Compressive
Strength
N/mm2
14th DAY
Compressive
Strength
N/mm2
28th DAY
Compressive
Strength
N/mm2
0% 35.18 37.49 37.75
1% 40.59 41.35 41.49
2% 40.89 42.96 43.41
3% 41.48 45.92 47.35
4% 39.65 40.10 45.39
Chart-1 Compressive Strength of NBD Concrete
3.2 DISCUSSIONS FOR COMPRESSIVE STRENGTH
 In 7th day curing Compressive Strength value for
the control mix was 40.59 N/mm2 for adding 1%
of NBD Fiber the Compressive Strength value is
40.89 N/mm2, the Strength was gradually
increased and reduced to 39.65 N/mm2 for 4 % of
addition of NBD Fiber. Strength increment is 1%
more than the nominal mix when adding the
NBD Fiber upto 4% and this percentage is
strength is decreases.
 Similarly In 14th day curing Compressive Strength
value for the control mix was 41.35 N/mm2 for
adding 1% of NBD Fiber the Compressive
Strength value is 42.96 N/mm2, the Strength was
gradually increased and reduced to 40.10 N/mm2
for 4 % of addition of NBD Fiber. Strength
increment is 1% more than the nominal mix
when adding the NBD Fiber upto 4% and this
percentage is strength is decreases.
percentage is strength is decreased.
 Hence the Optimum Amount of NBD Fibers is 3%.
The Compression Strength value for NBD
Concrete is 19.69% is greater than the
Conventional Concrete.
3.3 FLEXTURAL STRENGTH OF BEAMS
Flexural strength is the properties of the
hardened concrete which gives details about the capacity
of concrete in bending when a load acted at the midpoint
of the beam. It is calculated by using the following formula,
Flexural Strength = Pa/bd2 (when a > 13.3 cm for 10
specimen)
Where,
P= Applied Load in KN to the specimen.
b = Width of specimen in mm
d = Depth in mm of the specimen at the point of failure.
a = Distance of the crack from the near to the support in
mm
Table -5: Flexural Strength of Concrete
% OF
ADDITION
OF FIBER
7th DAY
Flexural
Strength
N/mm2
14th DAY
Flexural
Strength
N/mm2
28th
DAY
Flexural
Strength
N/mm2
0% 1.60 1.79 2.42
1% 1.62 2.26 2.72
2% 1.75 2.59 2.87
3% 2.25 2.73 3.76
4% 1.84 2.43 2.62
35.18
40.59 40.89 41.48 39.6537.49
41.35 42.96
45.92
40.1
37.75
41.49 43.41
47.35 45.39
0
10
20
30
40
50
0% 1% 2% 3% 4%
CompressiveStrengthin
N/mm2
Percentage of Addition of NBD Fibers 7t…

Chart-2: Flexural Strength of NBD Concrete
3.5 DISCUSSIONS FOR FLEXURAL STRENGTH
 In 7th day curing Compressive Strength value for
the control mix was 1.62 N/mm2 for adding 1% of
NBD Fiber the Compressive Strength value is 1.75
N/mm2, the Strength was gradually increased and
reduced to 1.69 N/mm2 for 4 % of addition of
NBD Fiber. Strength increment is 1% more
than the nominal mix when adding the NBD
Fiber upto 4% and this percentage is strength
is decreases.
percentage is strength is decreases.
percentage is strength is decreased.
 Hence the Optimum Amount of NBD Fibers is 3%.
The Flexural Strength value for NBD Concrete
is 55.37% is greater than the Conventional
Concrete.
4. CONCULSIONS
On performing test Structural Behaviour of Non-
Biodegradable Materials are learned and the following
conclusions are arrived.
 About 18% increase in Compressive Strength is
attained when Concrete is addition with 3 % of
NBD Fibers on 7-Days
 About 23% increase in Compressive Strength is
 About 25 % increase in Compressive Strength is
 About 41% increase in Flexural Strength is
The Strength Characteristics of Concrete with various
percentages of adding NBD Fiber in Concrete have been
studied.
The Compressive and Flexural Strength of Concrete
was improved by 25 % and 55% with three percentage
addition of NBD Fibers and beyond this percentage of
addition of fibers in concrete, strength of concrete is
gradually reduced.
REFERENCES
1) Awwad.E, Mabsout,M., hamead.,B Farran, M
and Khatib, H. (2012b) “ Studies on Fiber-
Reinforced concrete using Industrials Fibers “
Journal -The Construction and building Materials,
Elsevier Vol.35 October 2012.
2) Awwad,E, Mabsout,M., hamead.,B Farran,M
and Khatib,H. (2011) “ Preliminary Studies on
the use of Natural Fibers in Sustainable Concrete
“ Journal -The Lebanese Association for the
Advancement of Science, Vol.12 Issue No. June
2011
3) M.Frigione, (2010) “Recycling of PET Bottles as
Fine Aggregate in concrete” Waste management,
Scientific World Journal, Volume 30, Issue-6.
4) Marzouk (2007), “Use of Waste Plastic in
Concrete Mixture” in Waste Management,
International Journal for Innovative Research in
Science and Technology, Volume -10, Issue -29, ,
Page No. 33-38.
5) Ismail and Al-Hasahmi (2005) “Use Of Waste
Plastic in Concrete Mixtures as Aggregate
Replacement” Department of Environmental
Engineering. Scientific Research an Academic
Publisher, Volume 2, Page 40.
1.6 1.62 1.75
2.25
1.691.79
2.26
2.59 2.73
2.432.42
2.72 2.87
3.76
2.62
0
0.5
1
1.5
2
2.5
3
3.5
4
0% 1% 2% 3% 4%
FlexturalStrenghtinN/mm2
Percentage of Addition of NBD Fibers
Flexural Stength of Concrete Beams
7th Day 14th Day 28 th day

6) Al-Manaseer and Dalal (1997), “Recycled
Aggregates in Concrete of Plastic Aggregates”.
Journal of Chemical Engineering, IEB, Volume 19,
Issue 8, Page No. 47-52.
7) M. Perez-Pena and B. Mobasher (1994).
Mechanical Properties of Fiber Reinforced
Concrete Composites, Cement and Concrete
Research, 24 (6), 1121-1132.
8) S.Wenjun Qu, Xiaoliang Zhang and Haiqun
Huang (2009).Flexural Behaviour of Concrete
Beams Reinforced with Hybrid (GFRP and Steel)
bars. Journal of Composites for Construction,
ASCE. 13(5), 350 – 359.
9) IS 456:2000 Code book for Plain & Reinforced
Concrete.
10) IS 10262:2009 Guidelines for Concrete Mix
Proportioning
11) IS 383 – 1970: Specification for Aggregates from
Natural Sources for Concrete (Second revision)
12) IS 2386 – 1963: Methods of Test for Fine and
Coarse Aggregates for Concrete

IRJET- Structural Behaviour of Concrete Beam using Non Biodegradable Materials

More Related Content

What's hot

Similar to IRJET- Structural Behaviour of Concrete Beam using Non Biodegradable Materials

More from IRJET Journal

Recently uploaded

IRJET- Structural Behaviour of Concrete Beam using Non Biodegradable Materials