IRJET- Use of Plastic Aggregate and Crumb Rubber in Flexible Pavement

International Research Journal of Engineering and Technology (IRJET) e-ISSN: 2395-0056
Volume: 06 Issue: 03 | Mar 2019 www.irjet.net p-ISSN: 2395-0072
© 2019, IRJET | Impact Factor value: 7.211 | ISO 9001:2008 Certified Journal | Page 389
Use of Plastic Aggregate and Crumb Rubber in Flexible Pavement
Bhavesh Bafna1, Poonam Bhandare2, N.M. Patil3, Sanchit Jadhav4, Santosh Koravi5,
Hanmant Pujari6
---------------------------------------------------------------------***----------------------------------------------------------------------
Abstract - Disposal of waste materials including waste plastic bags has becomeaseriousproblemandwasteplasticsareburntfor
apparent disposal which cause environmental pollution. Utilization of waste plastic bags in bituminous mixes has proved that
these enhance the properties of mix in addition to solving disposal problems. Plastic waste is heated and moulded in the form of
aggregate and used as replacement to conventional aggregates. Besides rubber wastes (Crumb rubber) being burnt produces
combustion problems leading to releasing toxic gases and polluting environment.
Key Words: plastic aggregate, crumb rubber
1. INTRODUCTION
The main roads in India are under huge pressure and in great need of modernization in order to handle the increased
requirements of the Indian economy. In addition to maintenance, the expansion of the network andwideningof existingroads
is becoming increasingly important. This would then enable the roads to handle increased traffic, and also allow for a
corresponding increase in the average movement speed on India's roads.
Currently India's annual expenditure on the roadsectorisaroundRs20,000-30,000crore.Oneofthemajorreasonsbehindthis
huge expenditure on maintaining roads is due to the problems of overloading and poor maintenance
Besides the need for development of the roads the plastic and the rubber wastes need to be disposedofin ecofriendlyway.In a
vision to solve both these problems they are interlinked and an effective way is developed.
2. PROBLEM STATEMENT
India has been chosen as the global host of the world environment day that will focus on galvanizing greater action against
single-use plastic pollution on June 5 the previous year, by the United Nations Environment Programme(UNEP, now also
known as UN Environment). After demonstratingglobal leadershiponclimatechange, India will leadthechargeon‘Beatplastic
pollution’, the theme for World Environment 2018.According to UN estimates, every year the world uses 500 billion plastic
bags while half of the plastic used is of single use or in disposable items such as grocery bags, cutlery and straws. Each year, at
least eight million tonnes of plastic end up in the oceans, the equivalent of full garbage trucks every minute. Besides the
pollution caused due to rubber industry is peaking now a days. Global natural rubber production stood at 9.67 million metric
tonnes in 2006 and grew at a CAGR of 7.68 per cent during 2004-06. Asia is the largest source of natural rubber,accountingfor
around 94 per cent of the total world output. The three largest rubber producing countries are Indonesia, Malaysia and
Thailand, which together account for around 72 per cent of all natural rubber production. The Rubber Industry is a key sector
in the Indian economy. India is the third largest producer and fourth largest consumer of natural rubber in the world and also
the fifth largest consumer of natural rubber and synthetic rubber put together.
3. OBJECTIVES
The basic intention behind the proposed work is tomakeuseofthewastebeingproducedinoveralldevelopmentandreducethe
haphazard on human health.
Following are main objectives of the work:
1) To identify the optimum proportion of plastic aggregates blended along with crumb rubber to be added in the bitumen mix
for getting the required strength.
2) To compare the experimented results with the conventional pavement details and perform the economic analysis.
3) Generate jobs for rag pickers for collection of more and more plastic waste.
4) To reduce the need of bitumen to a certain extend by appropriate replacement of crumb rubber.
5) To make the roads more durable by addition of plastic waste to a specific design.
6) Avoid disposal of plastic waste by incineration and land filling and their by developing an eco-friendly way for waste
disposal.

4. EXPERIMENTAL WORK
For checking the quality of material following tests were conducted as enlisted above as per the standard specification:
A) Tests for aggregate (For conventional as well as plastic aggregate)
1. Aggregate Abrasion Test
2. Specific Gravity & Water Absorption Test [IS: 2386 (Part 3) 1963]
3. Aggregate Impact Value Test [IS: 2386 (part 4) 1963]
4. Aggregate Crushing Value [IS: 2386 (Part 4) 1963]
5. Flakiness & Elongation Index Test [IS: 2386 (part 1) 1963]
B) Tests for bitumen (for modified as well as conventional)
1. Penetration Test [IS: 1203-1978]
2. Softening Point Test [IS: 1205-1978]
3. Ductility Test [IS: 1208-1978]
4. Viscosity Test
5. RESULT ANALYSIS
After complete experimental work we can observe the effect of replacement of bitumen by crumb rubber. The mix turns out to
become stiffer and this results in increased durability of the pavement and hence the life of pavement.
The variation of properties is as shown in fig: 1 below:
Fig: 1 Comparison of properties of modified and conventional bituminous mix.
The average value of the above properties is determined for each mix with different bitumen content and the following
graphical plots are prepared:
1. Binder content versus corrected Marshall Stability
2. Binder content versus Marshall Flow
3. Binder content versus percentage of void (Vv) in the total mix
4. Binder content versus voids filled with bitumen (V FB)
5. Binder content versus unit weight or bulk specific gravity (Gm)
Due to variation in the plastic aggregate percentage following additional graphs are to be added
1. Plastic Aggregate percentage vs corrected Marshall Stability.
2. Plastic Aggregate percentage vs Marshall Flow.
3. Plastic Aggregate percentage vs percentage of void (Vv) in the total mix.
4. Plastic Aggregate percentage vs voids filled with bitumen (V FB).
5. Plastic Aggregate percentage vs unit weight or bulk specific gravity (Gm)

Fig: 2 Percentage of plastic aggregate vs Marshall Stability Value
Fig: 4 Percentage of plastic aggregate vs Bulk Specific Gravity (Gm)
Fig: 3 Percentage of plastic aggregate vs Percentage of void (Vv)
Fig: 5 Binder Content vs Marshall Stability Value

Fig: 6 Binder Content vs Bulk Specific Gravity (Gm)
Fig: 8 Binder Content vs Percentage of Void (Vv)
Fig: 7 Percentage of plastic aggregate vs Void with Bitumen (VFB)
Fig: 9 Percentage of plastic aggregate vs Marshall Flow Value

Fig: 10 Binder Content vs Void filled with bitumen (VFB)
Fig: 11 Binder Content vs Marshall Flow Value
6. CONCLUSION
Plastic aggregates are used for the better performance of roads. This helps to have a better binding of bitumen with plastic
wasted coated aggregate due to increased bonding and increased area ofcontactbetweenpolymersandbitumen.Thepolymer
coating also reduces the voids. This prevents the moisture absorption and oxidation of bitumen by entrapped air. This has
resulted in reducing rutting, raveling and there is no pothole formation. TheroadscanWithstandheavytrafficandshowbetter
durability.
Following are some points which are drawn from the study:
1. Softening point of the plain bitumen was found to be increased by significant amount anditisadvantageoustouse instead of
plain bituminous mix.
2. After mixing crumb rubber to bituminous mix they acquire additional stiffness which makes the overall composite more
durable.
3. After complete analysis of the graph we can conclude thatroadscanbemadeby100%plasticaggregateand5% replacement
of bitumen without any decrease in strength.
4. Stripping Value was reduced from 1% for control specimen to nil and remained same for additional 5%crumb rubber and
10% Crumb rubber to bituminous mix. This shows that additional 5% crumb rubber is more suitable for bituminous
construction than plain bituminous mixes.
In short we can conclude that, using plastic waste in mix will help reduction in need of bitumen by around 10%, increase the
strength and performance of road, avoid use of anti-stripping agent, avoid disposal of plastic waste by incineration and land
filling and ultimately develop a technology, which is ecofriendly. Increased traffic conditionswill andarereducingthelifespan
of roads. Plastic roads are means of prevention and ultimately will be the cure. Itwill saveenvironmentandreducetheamount
of resources used for construction.

REFERENCES
1. Al-Hadidy A.I., Yi-qiu Tan (2009), “Effect of polyethylene on life of flexible pavements”, Construction andBuilding Materials,
Vol. 23.
2. Verma S. S., (Nov. 2008), “Roads from plastic waste”, Science Tech Entrepreneur, the Indian Concrete Journal, P.No.43 - 44.
3.Yue Huang, Roger N. Bird, Oliver Heidrich 2.,(2007), “A review of the use of recycled solid waste materials inasphalt
pavements”, Resources, Conservation and Recycling,Vol.52,School ofCivil Engineering andGeosciences,NewcastleUniversity,
UK, pp 58-73.
4. I.Vegas, J.A. Iban˜ez, J.T. San Jose´, A. Urzelai., (2008), “Construction demolition wastes, Waelz slag and MSWIbottom ash: A
comparative technical analysis as material for road construction”, Waste Management, Vol. 28, pp565–574
5.Bandopandhyay T. K., (Jan. - Mar. 2010), “Construction of Asphalt Road with Plastic Waste”, Indian Center forPlastic in
Environment (ICPE), ENVIS – Eco- Echoes, Vol.11, Issue 1.
6. S.K. Khanna and C.E.G Justo “Highway Engineering” 2008.
7. A.I.AI Hadidy, Tan Yi-qui, (2009) “Effects of polyethylene on life of flexible pavements” 1456- 1464, Construction and
Building materials 23.
8. L.R Schroceder, “The Use of Recycled Materials in Highway construction’, Public Roads, Vol 58(Issue 2), 1994
8. S.S. Verma. “Roads from Plastic Waste”, the Indian Concrete Journal, p. 43-44.November 2008.

IRJET- Use of Plastic Aggregate and Crumb Rubber in Flexible Pavement

More Related Content

What's hot

Similar to IRJET- Use of Plastic Aggregate and Crumb Rubber in Flexible Pavement

More from IRJET Journal

Recently uploaded

IRJET- Use of Plastic Aggregate and Crumb Rubber in Flexible Pavement