Momento en estructuras

93
Chapter 6
Basic mechanics
Basic principles of statics
Statics is the branch of mechanics that deals with the
equilibrium of stationary bodies under the action of
forces. The other main branch – dynamics – deals with
moving bodies, such as parts of machines.
Static equilibrium
A planar structural system is in a state of static
equilibrium when the resultant of all forces and all
moments is equal to zero, i.e.
y
x
∑Fx = 0
∑Fy = 0
∑Ma = 0
or
∑Fx = 0
∑Ma = 0
∑Mb = 0
or
∑Fy = 0
∑Ma = 0
∑Mb = 0
or
∑Ma = 0
∑Mb = 0
∑Mc = 0
where F refers to forces and M refers to moments of
forces.
Static determinacy
If a body is in equilibrium under the action of coplanar
forces, the statics equations above must apply. In general,
three independent unknowns can be determined from
the three equations. Note that if applied and reaction
forces are parallel (i.e. in one direction only), then only
two separate equations can be obtained and thus only
two unknowns can be determined. Such systems of
forces are said to be statically determinate.
Force
A force is defined as any cause that tends to alter the
state of rest of a body or its state of uniform motion
in a straight line. A force can be defined quantitatively
as the product of the mass of the body that the force is
acting on and the acceleration of the force.
P = ma
where
P = applied force
m = mass of the body (kg)
a = acceleration caused by the force (m/s2
)
The Système Internationale (SI) units for force are
therefore kg m/s2
, which is designated a Newton (N).
The following multiples are often used:
1 kN = 1 000 N, 1 MN = 1 000 000 N
All objects on earth tend to accelerate toward the
centre of the earth due to gravitational attraction; hence
the force of gravitation acting on a body with the mass
(m) is the product of the mass and the acceleration due
to gravity (g), which has a magnitude of 9.81 m/s2
:
F = mg = vρg
where:
F = force (N)
m = mass (kg)
g = acceleration due to gravity (9.81m/s2
)
v = volume (m³)
ρ = density (kg/m³)
Vector
Most forces have magnitude and direction and can be
shown as a vector. The point of application must also be
specified. A vector is illustrated by a line, the length of
which is proportional to the magnitude on a given scale,
and an arrow that shows the direction of the force.
Vector addition
The sum of two or more vectors is called the resultant.
The resultant of two concurrent vectors is obtained by
constructing a vector diagram of the two vectors.
The vectors to be added are arranged in tip-to-tail
fashion. Where three or more vectors are to be added,
they can be arranged in the same manner, and this is
called a polygon. A line drawn to close the triangle
or polygon (from start to finishing point) forms the
resultant vector.
The subtraction of a vector is defined as the addition
of the corresponding negative vector.
A
Q
P

94 Rural structures in the tropics: design and development
Resolution of a force
In analysis and calculation, it is often convenient to
consider the effects of a force in directions other than
that of the force itself, especially along the Cartesian
(xx-yy) axes. The force effects along these axes are
called vector components and are obtained by reversing
the vector addition method.
Fy is the component of F in the y direction Fy = F sinθ
Fx is the component of F in the x direction Fx = F cosθ
P
Q
A
R
=
P
+
Q
P
Q
A
R
=
P
+
Q
A
P
Q
S
R = P + Q + S
y
x
Fy
0
F
θ
Fx
Concurrent coplanar forces
Forces whose lines of action meet at one point are
said to be concurrent. Coplanar forces lie in the same
plane, whereas non-coplanar forces have to be related
to a three-dimensional space and require two items
of directional data together with the magnitude. Two
coplanar non-parallel forces will always be concurrent.
Equilibrium of a particle
When the resultant of all forces acting on a particle is
zero, the particle is in equilibrium, i.e. it is not disturbed
from its existing state of rest (or uniform movement).
The closed triangle or polygon is a graphical
expression of the equilibrium of a particle.
The equilibrium of a particle to which a single force
is applied may be maintained by the application of a
second force that is equal in magnitude and direction, but
opposite in sense, to the first force. This second force,
which restores equilibrium, is called the equilibrant.
When a particle is acted upon by two or more forces, the
equilibrant has to be equal and opposite to the resultant
of the system. Thus the equilibrant is the vector drawn
closing the vector diagram and connecting the finishing
point to the starting point.
A
Q
P
P
Q
A
RESULTANT
P
Q
A
EQ
UILIBRANT

95Chapter 6 – Basic mechanics
Free-body diagram of a particle
A sketch showing the physical conditions of a problem
is known as a space diagram. When solving a problem it
is essential to consider all forces acting on the body and
to exclude any force that is not directly applied to the
body. The first step in the solution of a problem should
therefore be to draw a free-body diagram.
A free-body diagram of a body is a diagrammatic
representation or a sketch of a body in which the body
is shown completely separated from all surrounding
bodies, including supports, by an imaginary cut, and
the action of each body removed on the body being
considered is shown as a force on the body when
drawing the diagram.
To draw a free-body diagram:
1. Choose the free body to be used, isolate it from
any other body and sketch its outline.
2. Locate all external forces on the free body and
clearly mark their magnitude and direction. This
should include the weight of the free body, which
is applied at the centre of gravity.
3. Locate and mark unknown external forces and
reactions in the free-body diagram.
4. Include all dimensions that indicate the location
and direction of forces.
The free-body diagram of a rigid body can be
reduced to that of a particle. The free-body of a particle
is used to represent a point and all forces working on it.
Example 6.1
Determine the tension in each of the ropes AB and AC
B
A
Space diagram
C
ABT
ABT
ACT
A
980 N
Free body diagram
for point A
980 N
Example 6.2
A rigid rod is hinged to a vertical support and held
at 50° to the horizontal by means of a cable when a
weight of 250 N is suspended as shown in the figure.
Determine the tension in the cable and the compression
in the rod, ignoring the weight of the rod.
The forces may also be calculated using the law of sines:
Point of concurrency
Three coplanar forces that are in equilibrium must all
pass through the same point. This does not necessarily
apply for more than three forces.
ABT
ACT
A
980 N
Free body diagram
for point A
980 N
50°
Space diagram
250 N
75° A
40°
65°
Free-body diagram for point A
40°
65°
Tension 180 N
Compression
265 N
250 N
75°
Force triangle
sin 65°
250 N
=
sin 40°
Tension in cable
=
sin 75°
Compression in rod

If two forces (which are not parallel) do not meet at
their points of contact with a body, such as a structural
member, their lines of action can be extended until they
meet.
Collinear forces
Collinear forces are parallel and concurrent. The sum of
the forces must be zero for the system to be in equilibrium.
Coplanar, non-concurrent, parallel forces
Three or more parallel forces are required. They will be
in equilibrium if the sum of the forces equals zero and
the sum of the moments around a point in the plane
equals zero. Equilibrium is also indicated by two sums
of moments equal to zero.
Reactions
Structural components are usually held in equilibrium
by being secured to rigid fixing points; these are often
other parts of the same structure. The fixing points or
supports will react against the tendency of the applied
forces (loads) to cause the member to move. The forces
generated in the supports are called reactions.
In general, a structural member has to be held or
supported at a minimum of two points (an exception to
this is the cantilever). Anyone who has tried ‘balancing’
a long pole or a similar object will realize that, although
only one support is theoretically necessary, two are
needed to give satisfactory stability.
Resultant of gravitational forces
The whole weight of a body can be assumed to act at
the centre of gravity of the body for the purpose of
determining supporting reactions of a system of forces
that are in equilibrium. Note that, for other purposes, the
gravitational forces cannot always be treated in this way.
Example 6.3
A ladder rests against a smooth wall and a person
weighing 900 N stands on it at the middle. The weight
Table 6.1
Actions and reactions
θ θ
N
N
F
Rx
Ry
y y y
H
M V
Smooth surfaces
Rough surfaces
Roller support
Pin support
Built-in support
Flexible cable or rope
Reaction is normal to the surface, i.e., at right angles to
the tangent.
Rough surface is capable of supporting a tangental
force as well as a normal reaction. Resultant reaction
is vectorial sum of these two.
Reaction is normal to the supporting surface only.
A freely hinged support is fixed in position, hence the
two reaction forces, but is not restrained in direction - it
is free to rotate.
The support is capable of providing a longitudinal
reaction (H), a lateral or transverse reaction (V), and a
moment (M). The body is fixed in position and fixed in
direction.
Force exerted by the cable or rope is always tension
away from the fixing, in the direction of the tangent to
the cable curve.

of the ladder is 100 N. Determine the support reactions
at the wall (RW) and at the ground (RG).
As the wall is smooth, the reaction RW must be at
right angles to the surface of the wall and is therefore
horizontal. A vertical component would have indicated
a friction force between the ladder and the wall. At the
bottom, the ladder is resting on the ground, which is
not smooth, and therefore the reaction RG must have
both a vertical and a horizontal component.
As the two weight forces in this example have the
same line of action, they can be combined into a single
force, reducing the problem from one with four forces
to one with only three forces. The point of concurrency
W = (900 + 100) N
Space diagram
3 m
6m
Rw A
1 000 N
RGx
RGy
Free-body diagram of ladder
A
Rw= 250 N
RG= 1 030.8
1 000 N
Force diagram
(A) can then be found, giving the direction of the
ground reaction force. This in turn enables the force
vector diagram to be drawn, and hence the wall and
ground reactions determined.
Example 6.4
A pin-jointed framework (truss) carries two loads,
as shown. The end A is pinned to a rigid support,
while the end B has a roller support. Determine the
supporting reactions graphically:
1. Combine the two applied forces into one and
find the line of action.
2. Owing to the roller support reaction RB will be
vertical. Therefore the resultant line (RL) must
be extended to intersect the vertical reaction of
support B. This point is the point of concurrency
for the resultant load, the reaction at B and the
reaction at A.
3. From this point of concurrency, draw a line
through the support pin at A. This gives the line
of action of the reaction at A.
4. Usethesethreeforcedirectionsandthemagnitude
of RL to draw the force diagram, from which RA
and RB can be found.
Answer: RA = 12.2 kN at 21° to horizontal.
RB = 12.7 kN vertical.
12 kN
15 kN
BA
RL
RL 15
12
RB
C
RL
RL
RB
RB
RA
RA
C

The link polygon (see an engineering handbook)
may also be used to determine the reactions to a beam
or a truss, though it is usually quicker and easier to
obtain the reactions by calculation, the method shown in
Example 6.4, or a combination of calculation and drawing.
However, the following conditions must be satisfied.
1. All forces (apart from the two reactions) must be
known completely, i.e. magnitude, line of action
and direction.
2. The line of action of one of the reactions must
be known.
3. At least one point on the line of action for the
other reaction must be known (2 and 3 reduce the
number of unknowns related to the equations of
equilibrium to an acceptable level).
Moments of forces
The effect of a force on a rigid body depends on its point
of application, as well as its magnitude and direction. It
is common knowledge that a small force can have a
large turning effect or leverage. In mechanics, the term
‘moment’ is used instead of ‘turning effect’.
The moment of force with a magnitude (F) about
a turning point (O) is defined as: M = F × d, where
d is the perpendicular distance from O to the line of
action of force F. The distance d is often called lever
arm. A moment has dimensions of force times length
(Nm). The direction of a moment about a point or
axis is defined by the direction of the rotation that the
force tends to give to the body. A clockwise moment
is usually considered as having a positive sign and an
anticlockwise moment a negative sign.
The determination of the moment of a force in a
coplanar system will be simplified if the force and its
point of application are resolved into its horizontal and
vertical components.
Example 6.5
As the ladder in Example 6.3 is at rest, the conditions
of equilibrium for a rigid body can be used to calculate
the reactions. By taking moments around the point
where the ladder rests on the ground, the moment of
the reaction RG can be ignored as it has no lever arm
(moment is zero). According to the third condition
for equilibrium, the sum of moments must equal zero,
therefore:
(6 × RW) - (900 N × 1.5 m) - (100 N × 1.5 m) = 0
RW = 250 N
The vertical component of RG must, according to the
second condition, be equal but opposite to the sum of
the weight of the ladder and the weight of the person
on the ladder, because these two forces are the only
vertical forces and the sum of the vertical forces must
equal zero, i.e.
RGy = 1 000 N
Using the first condition of equilibrium it can be seen
that the horizontal component of RG must be equal but
opposite in direction to RW, i.e.
RGX = 250 N
Because RG is the third side of a force triangle, where
the other two sides are the horizontal and vertical
components, the magnitude of RG can be calculated as:
(1 0002
+ 2502
)½
= 1 030.8 N
Resultant of parallel forces
If two or more parallel forces are applied to a
horizontal beam, then theoretically the beam can be
held in equilibrium by the application of a single force
(reaction) that is equal and opposite to the resultant R.
The equilibrant of the downward forces must be equal
and opposite to their resultant. This provides a method
for calculating the resultant of a system of parallel
forces. However, two reactions are required to ensure
the necessary stability, and a more likely arrangement
will have two or more supports.
The reactions RA and RB must both be vertical because
there is no horizontal force component. Furthermore,
the sum of the reaction forces RA and RB must be equal
to the sum of the downward-acting forces.
Beam reactions
The magnitude of the reactions may be found by the
application of the third condition for equilibrium, i.e.
the algebraic sum of the moments of the forces about
any point must be zero.
Take the moments around point A, then:
(80 × 2) + (70 × 4) + (100 × 7) + (30 × 10) - (RB × 12) = 0;
Giving RB = 120 kN
RA is now easily found with the application of the
second condition for equilibrium.
RA - 80 - 70 - 100 - 30 + RB=0; with RB = 120 kN gives:
RA=160 kN.
80 kN 70 kN 100 kN 30 kN
RA RB
2 m3 m3 m2 m2 m

Couples
Two equal, parallel and opposite but non-collinear
forces are said to be a couple.
A couple acting on a body produces rotation. Note
that the couple cannot be balanced by a single force.
To produce equilibrium, another couple of equal and
opposite moment is required.
Loading systems
Before any of the various load effects (tension,
compression, bending, etc.) can be considered, the
applied loads must be rationalized into a number of
ordered systems. Irregular loading is difficult to deal
with exactly, but even the most irregular loads may
be reduced and approximated to a number of regular
systems. These can then be dealt with in mathematical
terms using the principle of superposition to estimate
the overall combined effect.
Concentrated loads are those that can be assumed to
act at a single point, e.g. a weight hanging from a ceiling,
or a person pushing against a box.
Concentrated loads are represented by a single arrow
drawn in the direction, and through the point of action, of
the force. The magnitude of the force is always indicated.
Uniformly distributed loads, written as UDL, are
those that can be assumed to act uniformly over an area
or along the length of a structural member, e.g. roof
loads, wind loads, or the effect of the weight of water
on a horizontal surface. For the purpose of calculation,
a UDL is normally considered in a plane.
Incalculatingreactions,uniformlydistributedloadscan
in most, but not all, cases be represented by a concentrated
load equal to the total distributed load passing through the
centre of gravity of the distributed load.
150 mm
F=20N
F=20N150 mm
This technique must not be used for calculation of
shear force, bending moment or deflection.
Example 6.6
Considerasuspendedfloorwheretheloadsaresupported
by a set of irregularly placed beams. Let the load arising
from the weight of the floor itself and the weight of any
material placed on top of it (e.g. stored grain) be 10 kPa.
Determine the UDL acting on beam A and beam C.
It can be seen from the figure below that beam A carries
the floor loads contributed by half the area between the
beams A and B, i.e. the shaded area L. Beam C carries
the loads contributed by the shaded area M.
Therefore beam A carries a total load of:
1 m × 4 m × 10 kPa = 40 kN, or 40 kN / 4 = 10 kN / m.
In the same way, the loading of beam C can be
calculated to 25 kN / m. The loading per metre run can
then be used to calculate the required size of the beams.
4·0m
2·0 m
FLOOR PLAN
FLOOR SECTION
BEAM
A B C D
3·0 m 2·0 m
4·0m
2·0 m 3·0 m 2·0 m
1·0 m1·0 m
2·5 m
L M

Distributed load with linear variation is another
common load situation. The loading shape is triangular
and is the result of such actions as the pressure of water
on retaining walls and dams.
Shear force and bending moment of beams
A beam is a structural member subject to lateral loading
in which the developed resistance to deformation is of a
flexural character. The primary load effect that a beam
is designed to resist is that of bending moments but, in
addition, the effects of transverse or vertical shearing
forces must be considered.
Shear force (V) is the algebraic sum of all the
transverse forces acting to the left or to the right of the
chosen section.
Bending moment (M) at any transverse cross-section
of a straight beam is the algebraic sum of the moments,
10kN/m
4·0 m
25 kN/m
Loading of beam C
Loading of beam A
4·0 m
Distributed loads with linear variation
taken about an axis passing through the centroid of the
cross-section, of all the forces applied to the beam on
either side of the chosen cross-section.
Consider the cantilever AB shown in (A). For
equilibrium, the reaction force at A must be vertical and
equal to the load W.
The cantilever must therefore transmit the effect of
load W to the support at A by developing resistance
(on vertical cross-section planes between the load and
the support) to the load effect called shearing force.
Failure to transmit the shearing force at any given
section, e.g. section x-x, will cause the beam to fracture
as in (B).
The bending effect of the load will cause the beam
to deform as in (C). To prevent rotation of the beam at
the support A, there must be a reaction moment at A,
shown as MA, which is equal to the product of load W
and the distance from W to point A.
The shearing force and the bending moment
transmitted across the section x-x may be considered as
the force and moment respectively that are necessary to
maintain equilibrium if a cut is made severing the beam
at x-x. The free-body diagrams of the two portions of
the beam are shown in (D).
Then the shearing force between A and C = Qx =
W and the bending moment between A and C = Mx =
W × AC.
Note: Both the shearing force and the bending
moment will be zero between C and B.
(A) W
X
X
R=W
C
BA
(B)
W
A
X
X
R
C
B

Definitions
Shear force (Q) is the algebraic sum of all the transverse
forces acting to the left or to the right of the chosen
section.
Bending moment (M) at any transverse cross section
of a straight beam is the algebraic sum of the moments,
taken about an axis passing through the centroid of the
cross section, of all the forces applied to the beam on
either side of the chosen cross section.
Table 6.2 shows the sign convention for shear
force (Q) and bending moment (M) used in this book.
Shearing forces, which tend to make the part of the
beam to the left move up and the right part move
down, are considered positive. The bending moment is
considered positive if the resultant moment is clockwise
on the left and anticlockwise on the right. These tend to
make the beam concave upwards and are called sagging
bending moments. If the moment is anticlockwise on
the left and clockwise on the right, the beam will tend
to become convex upwards – an effect called hogging.
Table 6.2
Shearing and bending forces
Load
effect Symbol
Sign convention
UnitsPositive (+) Negative (–)
Shearing
force
Q
Up on the left Down on the left
N
kN
Bending
moment
M Sagging
(top ﬁbre in compression)
Hogging
(top ﬁbre in tension)
Nm
kNm
Nmm
Shear-force variation
Concentrated loads will change the value of the shear
force only at points where they occur, i.e. the shear
(C)
MA
MA
QX
QX
MX
MX
W
X
X
C
B
A
(D)
W
X
R
force remains constant in between. When the load is
uniformly distributed, however, the shear force will
vary at a uniform rate. Thus it will be seen that uniform
loads cause gradual and uniform change of shear, while
concentrated loads bring a sudden change in the value
of the shear force.
Bending moment variation
Concentrated loads will cause a uniform change of the
bending moment between the points of action of the
loads. In the case of uniformly distributed loads, the
rate of change of the bending moment will be parabolic.
Maximum bending moment values will occur where the
shear force is zero or where it changes sign.
Shear-force (SF) and bending-moment (BM)
diagrams
Representative diagrams of the distribution of shearing
forces and bending moments are often required at
several stages in the design process. These diagrams
are obtained by plotting graphs with the beams as the
base and the values of the particular effect as ordinates.
It is usual to construct these diagrams in sets of three,
representing the distribution of loads, shearing forces
and bending moments respectively. These graphical
representations provide useful information regarding:
1. The most likely section where a beam may fail in
shear or in bending.
2. Where reinforcement may be required in certain
types of beam, e.g. concrete beams.
3. The shear-force diagram will provide useful
information about the bending moment at any
point.
4. The bending-moment diagram gives useful
information on the deflected shape of the beam.
Some rules for drawing shear-force and bending-
moment diagrams are:
1. In the absence of distributed loads, the shear-
force diagram consists of horizontal steps and the
bending-moment diagram is a series of straight
lines.
2. For a beam (or part of a beam) carrying a UDL
only, the shear-force diagram is a sloping straight
line and the bending diagram is a parabola.
3. At the point where the shear-force diagram
passes through zero (i.e. where the SF changes
sign), the BM has a maximum or minimum value.
4. Over a part of the span for which SF is zero, the
bending moment has a constant value.
5. At a point where the bending-moment diagram
passes through zero, the curvature changes from
concave upwards to concave downwards or vice
versa. This point is referred to as point of inflexion.
6. If a beam is subjected to two or more different
systems of loading, the resulting shear and
bending moment at a given section is the algebraic
sum of the values at the section. This is referred to

as the principle of superposition and applies also
to bending stresses, reactions and deflections.
Thefollowingexampledemonstratestheconstruction
of diagrams representing shearing forces and bending
moments.
Example 6.7
The distribution of loads in a simply supported beam is
as given in the diagram below. Determine the reactions
at the supports and draw the shear-force and bending-
moment diagram.
Solution:
(a) Draw the free-body diagram of the beam.
(b) Determine the reactions at the supports. First use
the condition for equilibrium of moments about
a point:
∑ ME = 0
ME = (P × a) + (w1 × b × b / 2 ) + w2 × c(b+c / 2)
- RG (b + c) = 0
ME = -(10 × 10) + (2 × 10 × 5) + 4 × 10 × (15)
- RG (20) = 0
RG = 30 kN
∑Fy = 0 hence
∑Fy = RE + RG - P-(w1 × b) - ( w2 × c) = 0
∑ Fy = RE + 30 -10 - (2 × 10) - (4 × 10) = 0
RE = 40 kN
(c) Draw the shear-force diagram (SFD) directly
below the loading diagram and choose a
convenient scale to represent the shear force.
Calculate the values of the shear force to the left and
to the right of all critical points. Critical points are:
• at concentrated loads;
• at reactions;
• at points where the magnitude of a distributed
load changes.
W1 = 2 kN/m
P = 10 kN
D F
E G
W2 = 4 kN/m
b = 10 ma = 10 m c = 10 m
2 kN/m
P = 10 kN
D F
ER R= 40 kN = 30 kN
E G
G
4 kN/m
b = 10 ma = 10 m c = 10 m
1. Consider a section through the beam just to
the left of D, and find the algebraic sum of all
vertical forces to the left of this section. ∑Fy = 0,
therefore, shear force to the left of D is zero.
2. Consider a section just to the right of D, algebraic
sum of forces to the left of this section is 10 kN
down to the left. Hence, shear force to the right
of D is 10 kN (negative).
3. The same result as in point 2 above will be found
for any such section between D and E. The
shear-force diagram between D and E is thus a
horizontal line at -10 kN.
4. Consider a section just to the right of E; the
algebraic sum of forces to the left of this section
is made up of P and RE given that the shear force
equals (-10 + 40) kN = + 30 kN, i.e. up to the
left of section. Thus at E the shear-force diagram
changes from -10 kN to + 30 kN.
5. As we approach the right-hand end of the beam
we find the mathematics easier to consider on
the right-hand side of any section. Section just
to the left of F. Shear force = (4 kN / m × 10 m)
- (30 kN) using the sign convention to determine
positive or negative. Shear force here equals +
40 - 30 = + 10 kN.
6. Section just to the right of F. Shear force = + 40 -
30 = + 10 kN (i.e. no sudden change at F).
7. Section just to the left of G. Shear force = -30 kN
8. Variation of shear under a distributed load must
be linear.
Note the following from the shear-force diagram:
• Maximum shear force occurs at E and G where
the values are + 30 kN and - 30 kN respectively.
These two transverse sections are the two most
likely points for failure in shear.
• The maximum bending moment will occur where
the shear force is zero or where the shear force
changes sign. However, note that cantilevered
beams will always have maximum bending at the
fixed end.
2 kN/m
P = 10 kN
D F
ER = 40 kN
-30 kN
E G
= 30 kNRG
4 kN/m
b = 10 ma = 10 m c = 10 m
0 10
-10 kN
20
H
30
m
30
20
10
0
-10
-20
-30
kN + 30 kN
+ 10 kN
S.F.D.

The shear-force diagram in the example has two
points where the shear force is zero. One is at E and
the other is between H and G. The position of H can
be calculated from the fact that at F the shear force
is 10 kN and, under the action of UDL to the right
of F, it reduces at the rate of 4 kN / m. It will read a
value of zero after 2.5 m, i.e. the point H is 2.5 m to
the right of F.
(d) Draw the bending-moment diagram directly
under the shear-force diagram and choose
a convenient scale to represent the bending
moment. Calculate values of the bending moment
at all critical points. Critical points for bending
moment are:
• ends of the beam;
• where the shear force is zero or changes sign;
• other points that experience has shown to be
critical.
Values of bending moment are calculated using the
definition and sign convention, and considering each
load (to one side of the point) separately. It is the effect
that one load would have on the bent shape at the
chosen point that determines the sign.
1. For the bending moment at D consider the left
side of this point MD = 0
2. For the bending moment at E consider the left
side of this point ME = P × a and the beam would
assume a hogging shape:
ME = -(10 × 10) = -100 kNm
3. For the bending moment at F consider the loads
to the right of this point, a sagging beam results
and:
MF = -(4 × 10 × 10 / 2) + (30 × 10) = 100 kNm
4. The bending moment at G is obviously zero
5. At point H we have the maximum bending
moment: considering the forces to the right of
this point gives
MH = -(4 × 7 512 × 7 5) + (30 × 7 5)
= 112.5 (sagging)
6. The variation of the bending moment under a
UDL is parabolic
7. If the inclusion of other points would be helpful
in drawing the curve, they should also be plotted.
Note the following from the bending-moment
diagram:
• The maximum negative bending-moment hogging
(100 kNm) occurs at E and the maximum positive
bending moment sagging (112.5 kNm) occurs at a
point between F and G. When designing beams in
materials such as concrete, the steel reinforcement
would have to be placed according to these
moments.
• The bending-moment diagram will also give
an indication as to how the loaded beam will
deflect. Positive bending moments (sagging) cause
compression in the top fibres of the beam, hence
they tend to bend the beam with the concave side
downwards.
• At the supported ends of a simple beam and at the
free end of a cantilevered beam, where there can
be no resistance to bending, the bending moment
is always zero.
Forces in pin-jointed frames
Designing a framework necessitates finding the forces
in the members. For the calculation of primary stresses,
each member is considered to be pin-jointed at each
end so that it can transmit an axial force only in the
direction of the line connecting the pin joints at each
end. The force can be a pure tension (conventionally
designated positive), in which case the member is called
a tie, or a pure compression (conventionally designated
negative), when the member is called a strut.
These are internal forces that must be in equilibrium
with the external applied forces.
- -
+
0 10 20
2∙5 m
30
m
30
20
10
0
-10
-20
-30
kN + 30 kN
+ 10 kN
S.F.D.
2 kN/m
P = 10 kN
D F
ER = 40 kN
E G
= 30 kNRG
4 kN/m
b = 10 ma = 10 m c = 10 m
-
+
30
m
100
50
0
-50
-100 -100 kNm
+112.5 kNm
B.M.D.

A number of different techniques can be used to
determine the forces in the members.
Joint analysis: This is based on considering the
equilibrium of each joint in turn and using the free-
body diagram for each joint.
Method of sections: The free-body diagram
considered is for a portion of the framework to one side
or the other of a cut section. The forces in the members
cut by the section are included in the free-body
diagram. Application of the equations of equilibrium
will solve the unknown forces in the cut section. This
provides an analytical solution and is most useful when
requiring the answers for one or two members only.
Example 6.8
Find the forces and their direction in the members BH
and HG by using the method of sections.
FHG is found by taking a moment about point C,
considering the right hand section (RHS) of the cut
1-1 is in equilibrium. The forces FHC and FBC have no
moment about point CBL because they intersect at and
pass through the point.
TIE
STRUT
INTERNAL FORCE
EXTERNAL FORCE
( all 30°, 60°, 90° triangle)
10 m
A E
H
B C D
G
30°
F
9 kN 9 kN12 kN
10 m 10 m 10 m
12 kN
C
1
1
D
G F
E
RE
9 kN
∑Mc = 0 (FHG × CG) + (9 × CD) - (RE × 20) = 0
CG = FX = 10 tan 30° = 5.774
CD = DE = FE / cos 30°
FE = EX / cos 30° = 11.547 m
CD = 11 547 / cos 30° = 13.333 m
RE = (9 + 12 + 12 ) / 2 = 15 kN
Hence (FHG × 5.774) + (9 × 13.333) - (15 × 20) = 0
FHG = 31.17
Take section 2-2.
HC = FE = 11.547 (FBH × 11.547) + (9 × 13.333)
- (15 × 20) = 0 FBH = 15.59 kN
It can therefore be seen that FGH and FBH must be
clockwise to have equilibrium about point C. The
members GH and HB are therefore in tension.
Mechanics of materials
Direct stress
When a force is transmitted through a body, the body
tends to change its shape. Although these deformations
are seldom visible to the naked eye, the many fibres
or particles that make up the body transmit the force
throughout the length and section of the body, and the
fibres doing this work are said to be in a state of stress.
Thus, a stress may be described as a mobilized internal
reaction that resists any tendency towards deformation.
As the effect of the force is distributed over the cross-
section area of the body, stress is defined as force
transmitted or resisted per unit area.
Thus
Area
Force
Stress =
The SI unit for stress is Newtons per square metre
(N / m²). This is also called a Pascal (Pa). However, it
is often more convenient to use the multiple N / mm².
12 kN
C
2
2
D
GH F
E
RE
9 kN

Note that 1 N / mm² = 1 MN / m² = 1 MPa
Tensile and compressive stress, which result from forces
acting perpendicular to the plane of cross-section in
question, are known as normal stress and are usually
symbolized with σ (the Greek letter sigma), sometimes
given a suffix t for tension (σt) or c for compression
(σc). Shear stress is produced by forces acting parallel
or tangential to the plane of cross-section and is
symbolized with τ (Greek letter tau).
Tensile stress
Example 6.9
Consider a steel bar that is thinner at the middle of its
length than elsewhere, and that is subject to an axial
pull of 45 kN.
If the bar were to fail in tension, it would be as a
result of breaking where the amount of material is at a
minimum. The total force tending to cause the bar to
fracture is 45 kN at all cross-sections but, whereas the
effect of the force is distributed over a cross-sectional
area of 1 200 mm² for part of the length of the bar, it is
distributed over only 300 mm² at the middle position.
Thus, the tensile stress is greatest in the middle and is:
MPa150=
mm2
300
kN45
=σt
1 000 kPa or 1 MPa=
m2
0.49
kN490
==Stress σc
Compressive stress
Example 6.10
A brick pier is 0.7 metres square and 3 metres high and
weighs 19 kN / m³. It is supporting an axial load from
a column of 490 kN. The load is spread uniformly over
the top of the pier, so the arrow shown in the diagram
merely represents the resultant of the load. Calculate
(a) the stress in the brickwork immediately under the
column, and (b) the stress at the bottom of the pier.
12 mm
25mm
24 mm
150mm
45 kN
45 kN
Solution a
Cross-section area = 0.49 m²
MPa150=
mm2
300
kN45
=σt
1 000 kPa or 1 MPa=
m2
0.49
kN490
==Stress σc
Solution b
Weight of pier = 0.7 m × 0.7 m × 3.0 m × 19 kN / m³
= 28 kN
Total load = 490 + 28 = 518 kN and
1 057 kPa=
m2
0.49
kN518
==Stress σc
MPa76=
mm2
78.5
kN6
==Shear stress τ
L
∆L
ε ===
original length
Change in length
Direct strain
Shear stress
Example 6.11
A rivet is used to connect two pieces of flat steel. If the
loads are large enough, the rivet could fail in shear, i.e.
not breaking but sliding of its fibres. Calculate the shear
stress of the rivet when the steel bars are subject to an
axial pull of 6 kN.
490 kN
3m
0∙7 m 0∙7 m
6 kN
6 kN
6 kN
6 kN
10 mm

Note that although the rivets do, in fact, strengthen
the connection by pressing the two steel bars together,
this strength cannot be calculated easily owing to
friction and is therefore neglected, i.e. the rivet is
assumed to give all the strength to the connection.
Cross-section area of rivet = 1/4 × π × 102
= 78.5 mm²
1 057 kPa=
m2
0.49
kN518
==Stress σc
MPa76=
mm2
78.5
kN6
==Shear stress τ
L
∆L
ε ===
original length
Change in length
Direct strain
Strain
When loads of any type are applied to a body, the body
will always undergo dimension changes; this is called
deformation. Tensile and compressive stresses cause
changes in length, torsional-shearing stresses cause
twisting, and bearing stresses cause indentation in the
bearing surface.
In farm structures, where a uniaxial state of stress
is the usual stress considered, the major deformation is
in the axial direction. Although there are always small
deformations present in the other two dimensions, they
are seldom significant.
1 057 kPa=
m2
0.49
kN518
==Stress σc
MPa76=
mm2
78.5
kN6
==Shear stress τ
L
∆L
ε ===
original length
Change in length
Direct strain
By definition strain is a ratio of change and thus it is a
dimensionless quantity.
Elasticity
All solid materials deform when they are stressed and,
as the stress increases, the deformation also increases.
In many cases, when the load causing the deformation
is removed, the material returns to its original size and
shape and is said to be elastic. If the stress is steadily
increased, a point is reached when, after the removal of
the load, not all of the induced strain is recovered. This
limiting value of stress is called the elastic limit.
Within the elastic range, strain is proportional to the
stress causing it. This is called the modulus of elasticity.
The greatest stress for which strain is still proportional
is called the limit of proportionality (Hooke’s law).
Thus, if a graph is drawn of stress against strain as
the load is gradually applied, the first portion of the
graph will be a straight line. The slope of this straight
line is the constant of proportionality, modulus of
Original length L
Elongation ∆L
Strained length
L + ∆L
elasticity (E), or Young’s modulus and should be
considered as a measure of the stiffness of a material.
=
Strain
Stress
=Modulus of elasticity
A∆L
FL
E =
The modulus of elasticity will have the same units as
stress (Pa). This is because strain has no units.
A convenient way of demonstrating elastic behaviour
is to plot a graph of the results of a simple tensile test
carried out on a thin mild steel rod. The rod is hung
vertically and a series of forces are applied at the lower
end. Two gauge points are marked on the rod and the
distance between them is measured after each force
increment has been added. The test is continued until
the rod breaks.
Figure 6.1 Behaviour of a mild steel rod under tension
Example 6.12
Two timber posts, measuring 150 millimetres square
and 4 metres high, are subjected to an axial load of
108 kN each. One post is made of pine timber (E =
7 800 MPa) and the other is Australian blackwood (E
= 15 300 MPa). How much will they shorten because
of the load?
Cross-section area A = 22 500 mm²; length L = 4 000 mm
Pine: mm2.5=
8007×50022
0004×000108
==
AE
FL
∆L
mm1.3
30015×50022
0004×000108
===
AE
FL
∆L
Australian blackwood:
mm2.5=
8007×50022
0004×000108
==
AE
FL
∆L
mm1.3
30015×50022
0004×000108
===
AE
FL
∆L
Factor of safety
The permissible stresses must, of course, be less than
the stresses that would cause failure of the members of
the structure – in other words there must be an ample
safety margin. (In 2 000 BC, a building code declared
the life of the builder to be forfeit should the house
collapse and kill the owner).
Ultimate or maximum stress
Upper yield
point
Stress (σ)
Srain (ε)
Stress at
failure
Lower yield point
Elastic limit
Plastic
Elastic
Limit of proportionality

Also, deformations must be limited because excessive
deflection may give rise to problems such as cracking of
ceilings, partitions and finishes, as well as adversely
affecting the functional needs.
Structural design is not an exact science and, while
calculated values of reactions, stresses, etc. may be
mathematically correct for the theoretical structure (i.e.
the model), they may be only approximate as far as the
actual behaviour of the structure is concerned.
For these and other reasons, it is necessary to ensure
that the design stress, working stress, allowable stress
and permissible stress are less than the ultimate stress
or the yield stress. This margin is called the factor of
safety.
factor of safety
Ultimate (or yield) stress
=Design stress
In the case of a material such as concrete, which does
not have a well defined yield point, or brittle materials
that behave in a linear manner up to failure, the factor
of safety is related to the ultimate stress (maximum
stress before breakage). Other materials, such as steel,
have a yield point where a sudden increase in strain
occurs, and at which point the stress is lower than
the ultimate stress. In this case, the factor of safety is
related to the yield stress in order to avoid unacceptable
deformations.
The value of the factor of safety has to be chosen
with a variety of conditions in mind, such as the:
• accuracy in the loading assumptions;
• permanency of the loads;
• probability of casualties or big economic losses in
case of failure;
• purpose of the building;
• uniformity of the building material;
• workmanship expected from the builder;
• strength properties of the materials;
• level of quality control ensuring that the materials
are in accordance with their specifications;
• type of stresses developed;
• cost of building materials.
Values of 3 to 5 are normally chosen when the factor of
safety is related to ultimate stress, and values of 1.4 to
2.4 are chosen when related to yield-point stress.
In the case of building materials such as steel
and timber, different factors of safety are sometimes
considered for common loading systems and for
exceptional loading systems, in order to save materials.
Common loadings are those that occur frequently,
whereas a smaller safety margin may be considered
for exceptional loadings, which occur less frequently
and seldom at full intensity, e.g. wind pressure,
earthquakes, etc.
Structural elements and loading
Applied loads
Applied loads fall into three main categories: dead
loads, wind loads and other imposed loads.
Dead loads are loads resulting from the self-
weight of all permanent construction, including roof,
walls, floor, etc. The self-weight of some parts of a
structure, e.g. roof cladding, can be calculated from the
manufacturer’s data sheets, but the self-weight of the
structural elements cannot be accurately determined
until the design is completed. Hence estimates of
self-weight of some members must be made before
commencing a design analysis and the values checked
upon completion of the design.
Wind loads are imposed loads, but are usually treated
as a separate category owing to their transitory nature
and their complexity. Very often wind loading proves
to be the most critical load imposed on agricultural
buildings. Wind loads are naturally dependent on wind
speed, but also on location, size, shape, height and
construction of a building.
Specific information concerning various load types
is presented in Chapter 8.
When designing a structure, it is necessary to
consider which combination of dead and imposed loads
could give rise to the most critical loading condition.
Not all the imposed loads will necessarily reach their
maximum values at the same time. In some cases (for
example, light open sheds), wind loads may tend to
cause the roof structure to lift, producing an effect
opposite in direction to that of the dead load.
Imposed loads are loads related to the use of the
structure and to the environmental conditions, e.g.
weight of stored products, equipment, livestock, vehicles,
furniture and people who use the building. Imposed
loads include earthquake loads, wind loads and snow
loads where applicable, and are sometimes referred to as
superimposed loads because they are in addition to the
dead loads.
Dynamic loading results from a change of loading,
resulting directly from the movement of loads. For
example, a grain bin may be affected by dynamic
loading if filled suddenly from a suspended hopper; it
is not sufficient to consider the load solely when the bin
is either empty or full.
Principle of superposition
This principle states that the effect of a number of loads
applied at the same time is the algebraic sum of the
effects of the loads applied singly.
3 kN
4 kN
1 kN
+
2 kN 6 kN
4 kN4 kN
=
2 kN 6 kN
5 kN7 kN
4 kN

Using standard load cases and applying the principle
of superposition, complex loading patterns can be
solved. Standard case values of shear force, bending
moment or deflection at particular positions along a
member can be evaluated, after which the total value
of such parameters for the actual loading system can be
found by algebraic summation.
Effects of loading
After the loads have been transformed into definable
load systems, the designer must consider how the loads
will be transmitted through the structure. Loads are not
transmitted as such, but as load effects.
It is usual practice to orientate the Cartesian z-z axis
along the length of the member and the x-x and y-y axes
along the horizontal and vertical cross-sectional axes
respectively, when considering a structural member that
occupies a certain space (see the figure below).
Primary load effects
A primary load effect is defined as being the direct
result of a force or a moment, which has a specific
orientation with respect to the three axes. Any single
load or combination of loads can give rise to one or
more of these primary load effects. In most cases, a
member will be designed basically to sustain one load
effect, usually the one producing the greatest effect.
In more complex situations, the forces and moments
are resolved into their components along the axes, after
which the load effects are first studied separately for
one axis at a time, and subsequently their combined
effects are considered when giving the member its size
and shape.
The choice of material for a member may be
influenced to some extent by the type of loading. For
instance, concrete has little or no strength in tension
and is therefore unsuitable for use alone as a tie.
Tension, compression, shear, bending and torsion
are all primary load effects. Secondary load effects,
such as deflection, are derived from the primary load
effects.
Y
Y
Z
Z
X
X
Structural elements
Cable
Cables, cords, strings, ropes and wires are flexible
because of their small lateral dimensions in relation to
their length, and therefore have very limited resistance
to bending. Cables are the most efficient structural
elements because they allow every fibre of the cross-
section to resist the applied loads up to any allowable
stress. However, their application is limited by the fact
that they can be used only in tension.
Rod
Rods, bars and poles are used to resist tensile or
compressive loads. In a rod or a bar under axial tension,
the full cross section can be considered and the full
allowable stress for the material can be used in design
calculations.
Column
Rods or bars under compression are the basis for vertical
structural elements such as columns, stanchions, piers
and pillars. They are often used to transfer load effects
from beams, slabs and roof trusses to the foundations.
They may be loaded axially or they may have to be
designed to resist bending when the load is eccentric.
Ties and struts
When bars are connected with pin joints and the
resulting structure loaded at the joints, a structural
framework called a pin-jointed truss or lattice frame
is obtained. The members are subjected only to axial
loads and members in tension are called ties, while
members in compression are called struts.

Beam
A beam is a member used to resist a load acting across
its longitudinal axis by transferring the effect over a
distance between supports – referred to as the span.
S
S
S S S S S S S
S S
S
S
SSSSS
S
TT
T
T T T T T
T TTTT
T
T T
Span
Built - in ends
Deﬂection shape
Simply supported
Cantilever
The load on a beam causes longitudinal tension
and compression stresses, and shear stresses. Their
magnitudes will vary along, and within, the beam.
The span that a beam can usefully cover is limited by
the self-weight of the beam, i.e. it will eventually reach a
length when it is capable of supporting only itself. To a
degree, this problem is overcome with the hollow web
beam and the lattice girder or frame. The safe span for
long, lightly loaded beams can be increased somewhat
by removing material from the web, even though the
shear capacity will be reduced.
Arch
The arch can be shaped such that, for a particular loading,
all sections of the arch are under simple compression with
no bending. Arches exert vertical and horizontal thrusts
on their supports, which can prove troublesome in the
design of supporting walls. This problem of horizontal
thrust can be eliminated by connecting a tension member
between the support points.
Frames
Plane frames are also made up of beams and columns,
the only difference being that they are rigidly connected
at the joints. Internal forces at any cross-section of the
plane frame member are: bending moment, shear force
and axial force.
Web
Flanges
Hallow web beam
Simple arch
BOW STRING ARCH
TIE

Properties of structural sections
When designing beams in bending, columns in
buckling, etc., it is necessary to refer to a number of
basic geometrical properties of the cross-sections of
structural members.
Area
Cross-section areas (A) are generally calculated in
square millimetres, because the dimensions of most
structural members are given in millimetres, and values
for design stresses found in tables are usually given in
Newtons per millimetre square (N / mm²).
Centre of gravity or centroid
This is a point about which the area of the section is
evenly distributed. Note that the centroid is sometimes
outside the actual cross-section of the structural element.
Reference axes
It is usual to consider the reference axes of structural
sections as those passing through the centroid. In general,
the x-x axis is drawn perpendicular to the greatest lateral
dimension of the section, and the y-y axis is drawn
perpendicular to the x-x axis, intersecting it at the centroid.
y
y
xx
C
y
y
xx
C
Moment of inertia
The area moment of inertia (I), or to use the more
correct term, second moment of area, is a property that
measures the distribution of area around a particular
axis of a cross-section, and is an important factor in its
resistance to bending. Other factors, such as the strength
of the material from which a beam is made, are also
important for resistance to bending, and are allowed for
in other ways. The moment of inertia measures only
how the geometric properties or shape of a section affect
its value as a beam or slender column. The best shape
for a section is one that has the greater part of its area as
distant as possible from its centroidal, neutral axis.
For design purposes, it is necessary to use the
moment of inertia of a section about the relevant axis
or axes.
Calculation of moment of inertia
Consider a rectangle that consists of an infinite number
of strips. The moment of inertia about the x-x axis of
such a strip is the area of the strip multiplied by the
square of the perpendicular distance from its centroid
to the x-x axis, i.e. b × ∆y × y2
The sum of all such products is the moment of
inertia about the x-x axis for the whole cross-section.
By applying calculus and integrating as follows, the
exact value for the moment of inertia can be obtained.
∫
+
−
==
2d
2d
12
bd3
by2
dyIxx
y
y
xx
C
b
d/2
d/2
y
∆y
xx

For a circular cross-section:
∫
+
−
==
2d
2d
12
bd3
by2
dyIxx
64
Ixx
πD4
=
Moments of inertia for other cross-sections are given later
and in Table 4.3. For structural rolled-steel sections, the
moment of inertia can be found tabulated in handbooks.
Some examples are given in Appendix V.3.
Principle of parallel axes
According to the principle of parallel axes, if the
moment of inertia of any area (e.g. top flange of the
beam shown below) about any axis is parallel to its
centroidal axis, then the product of the area of the shape
and the square of the perpendicular distance between
the axes must be added to the moment of inertia about
the centroidal axis of that shape.
Example 6.13
Determine the moment of inertia about the x-x axis and
the y-y axis for the I-beam shown in the figure. The
beam has a web of 10 mm plywood and the flanges are
made of 38 mm by 100 mm timber, which are nailed and
glued to the plywood web.
Solution:
The entire cross-section of both the beam and the
cross-section of the web have their centroids on the x-x
axis, which is therefore their centroidal axis. Similarly,
the F-F axis is the centroidal axis for the top flange.
Ixx of the web using mm4
106
×22.5
mm4
106
×7.2
=
12
3003
×10
=
12
bd3
=
12
1003
×86
The moment of inertia of one flange about its own
centroidal axis (F-F):
IFF of one flange =
mm4
106
×22.5
mm4
106
×7.2
=
12
3003
×10
=
12
bd3
=
12
1003
×86
Timber 38x100
86
F
x x
10
F
Plywood
500
300100
200
and from the principle of parallel axes, the Ixx of one
flange equals:
(7.2 × 106
) + (86 × 100 × 2002
) = 351.2 × 106
mm4
Thus the total Ixx of the web plus two flanges equals:
Ixx = (22.5 × 106
) + (351.2 × 106
) + (351.2 × 106
)
= 725 × 106
mm4
The Iyy of the above beam section is most easily found
by adding the Iyy of the three rectangles of which
it consists, because the y-y axis is their common
neutral axis, and moments of inertia may be added or
subtracted if they are related to the same axis.
4
mm106
×10.6=
106
×0.025+106
×5.3×2=
12
103
×300
+
12
863
×100
×2=yyI
Section modulus
In problems involving bending stresses in beams, a
property called section modulus (Z) is useful. It is the
ratio of the moment of inertia (I) about the neutral axis
of the section to the distance (C) from the neutral axis
to the edge of the section.
Unsymmetrical cross-sections
Sections for which a centroidal reference axis is not an
axis of symmetry will have two section moduli for that
axis.
y1
Ixx=Zxx1
y2
Ixx=Zxx2
;
86
10
300100
y
100
y
y1
y2
xx
y

Radius of gyration
Radius of gyration (r) is the property of a cross-section
that measures the distribution of the area of the cross-
section in relation to the axis. In structural design,
it is used in relation to the length of compression
members, such as columns and struts, to estimate their
slenderness ratio and hence their tendency to buckle.
Slender compression members tend to buckle about
the axis for which the radius of gyration is a minimum
value. From the equations, it will be seen that the least
radius of gyration is related to the axis about which the
least moment of inertia occurs.
Therefore,
A
Ixxrxx
=
A
Iyy
ryy
=and
A
Ixxrxx
=
A
Iyy
ryy
=
(general relationship I = Ar2
)
Table 6.3
Properties of structural sections
Section Area
(mm2
)
or (m2
)
Moment
of inertia
(mm4
) or (m4
)
Section
modulus
(mm3
) or (m3
)
Radius
of gyration
(mm) or (m)
Distance from
extreme ﬁbre
to centroid
(mm) or (m)
A Ixx Iyy Zxx Zyy rxx ryy y x
b
y
d
G
Rectangle
a
a
G
x
x
y
y
y
x
Square
a
G
y
x
x x
y
y
Square
with
diagonal
axes
G
y
x
x x
y
y Circle
G
d
D
y
x
x x
y
y Annulus
12
d
12
b
2
d
y =bd
12
bd3
12
db3
6
bd2
6
db
12
d
12
b
2
d
y =
12
a4
12
a4
6
a3
6
a3
12
a
12
a
y = =
2
a
xa2
y = =
2
a
xa2
12
a4
12
a4
26
a3
26
a3
12
a
12
a
4
D2
π D4
π
64
D3
π
32
D3
π
32
D4
π
64 4
D
4
D
2
D
y =
2
D
x =
2
D
y =
2
D
x =
4
(D2
− d2
)π
64
(D4
− d4
)π
32
(D4
− d4
)π
32
(D3
− d3
)π
4 (D2
+ d2
) 4 (D2
+ d2
)
32
(D3
− d3
)π

Review questions
1. Sketch the shear and bending moment diagrams
for the beams below, indicating values of shear
force and bending moment at the key points.
2. Find the reactions on beam BC.
3. Two concentrated loads of 100 kN and 200 kN
advance along a girder with a 20-metre span, the
distance between the loads being 8 metres. Find
the position of the section that has to support the
greatest bending moment, and calculate the value
of the bending moment.
4. A load of 100 kN, followed by another load
of 50 kN, at a distance of 10 metres, advances
across a girder with a 100-metre span. Obtain an
expression for the maximum bending moment at
a section of the girder at a distance of z metres
from an abutment.
W N/m
L
2
3
L
1
3
a)
b)
A
1
P
2
4
L/2 L/2
5
B C
60˚ 60˚
3
Further reading
Al Nageim, H., Durka, F., Morgan, W. & Williams
D.T. 2010. Structural mechanics: loads, analysis,
materials and design of structural elements. 7th
edition. London, Pearson Education.
Nelson, G.L., Manbeck, H.B. & Meador, N.F. 1988.
Light agricultural and industrial structures: analysis
and design. AVI Book Co.
Prasad, I.B. 2000. A text book of strength of materials.
20th
edition. 2B, Nath Market, Nai Sarak, Delhi,
Khanna Publishers.
Roy, S.K & Chakrabarty, S. 2009. Fundamentals
of structural analysis with computer analysis and
applications. Ram Nagar, New Delhi, S. Chand and
Company Ltd.
Salvadori, M. & Heller, R. 1986. Structure in
architecture: the building of buildings. 3rd
edition.
Englewood Cliffs, New Jersey, Prentice-Hall.
Whitlow, R. 1973. Materials and structures. New York,
Longman.

Momento en estructuras

More Related Content

What's hot (20)

Similar to Momento en estructuras (20)

Recently uploaded (20)

Momento en estructuras