OBSTACLE_AVOIDING_ROBOT.pptx

OBSTACLE_AVOIDING_ROBOT.pptx

• 1.
  Obstacle avoiding car •This project is made in ATL (Atal thinkring Lab) by • Rajeshwar pathak and Suman kumar Summited to uravasi mam And Prakash sir
• 2.
  ABSTRACT The project isdesign to build an obstacle avoidance robotic vehicle using ultrasonic sensors for its movement. A micro-controller is used to achieve the desired operation. A robot is a machine that can perform task automatically or with guidance. Robotics is a combination of computational intelligence and physical machines (motors). Computational intelligence involves the programmed instructions. This robot or a smart car is built to sense any obstacle in its path, to avoid it and resume its running involving the pre-computation of an obstacle free path. Ultrasonic sensors were adapted to implement a real-time obstacle avoidance system for wheeled robots, so that the robot can continually detect surroundings, avoid obstacles, and move toward the target area.
• 3.
  INTRODUCTION: An obstacle avoidingrobot is an intelligent device, which can automatically sense and overcome obstacles on its path. Obstacle Avoidance is a robotic discipline with the objective of moving vehicles on the basis of the sensorial information. The use of these methods front to classic methods (path planning) is a natural alternative when the scenario is dynamic with an unpredictable behaviour. In these cases, the surroundings do not remain invariable, and thus the sensory information is used to detect the changes consequently adapting moving. It will automatically scan the surrounding for further path.
• 4.
  EXISTING SYSTEM: An simplerobot, steering algorithm is used for robotic actions in which driver or a human being is controlling the robot using remote. Here driver is present, who can see the obstacle and navigate robot accordingly.
• 5.
  PROPOSED SYSTEM: The projectproposes a autonomous robotic vehicle, In which no remote is used for controlling the robotic actions. It intelligently detects obstacles present on its path through the sensors, avoid it and take decision on the basis of internal code that I set for it.
• 6.
  WORKS ON PROJECT: DESIGNROBOT: Obstacle Avoiding Robot is an intelligent device which can automatically sense the obstacle in front of it and avoid them by turning itself in another direction. An design of the Obstacle Avoiding Robot to…,
• 7.
  HARDWARECONFIGURATION: 1. Arduino Uno 2.Ultrasonic Range Sensor – HC – SR04 3. Motor Driver IC – L298n 4. DC Motors x 2 5. Power Batteries 6. Jumper Wires 7. Arduino Uno Wheels and Car CAD
• 8.
  1.ArduinoUno: The Arduino Unois an open source microcontroller board based on the Microchip ATmega328P microcontroller and developed by Arduino. The board is equipped with sets of digital and analog input/output (I/O) pins that may be interfaced to various expansion boards (shields) and other circuits. 2. Ultrasonic sensor: Ultrasonic sensor are devices that use electrical–mechanical energy transformation to measure distance from the sensor to the target object. Ultrasonic waves are longitudinal mechanical waves which travel as a sequence of compressions and rarefactions along the direction of wave propagation through the medium.
• 9.
  3. Motor DriverIC – L298N: Arduino board is connected with DC Motor through Motor driver board(pin10, pin11, pin12, pin13)which provide power to the actuators. Actuators are used to move robot in Forward, Backward, Left and Right directions. 4. DC Motors x 2 : DC motors normally have just two leads, one positive and one negative. If you connect these two leads directly to a battery, the motor will rotate. If you switch the leads, the motor will rotate in the opposite direction.
• 10.
  SOFTWARESPECIFICATION: Arduino is anopen-source electronics platform based on easy-to-use hardware and software. Arduino boards are able to read inputs - light on a sensor, a finger on a button, or a Twitter message - and turn it into an output - activating a motor, turning on an LED, publishing something online. You can tell your board what to do by sending a set of instructions to the microcontroller on the board. To do so you use the Arduino programming language, and the Arduino Software IDE based on processing.
• 11.
  CIRCUIT DIAGRAM:
• 12.
  FLOWCHAT PROCESS:
• 13.
  CONCLUSION: The goal ofMy project is to create a autonomous robot which intelligently detects the obstacle in his path and navigate according to the actions that I set for it. This project developed an obstacle avoiding robot to detect and avoid obstacles in its path. The robot is built on the Arduino platform for data processing and its software counterpart helped to communicate with the robot to send parameters for guiding movement. For obstacle detection, three ultrasonic distance sensors were used that provided a wider field of detection. The robot is fully autonomous and after the initial loading of the code, it requires no user intervention during its operation. When placed in unknown environment with obstacles, it moved while avoiding all obstacles with considerable accuracy.