Parametric Analysis of Single Element U Slot Microstrip Antenna

IJSRD - International Journal for Scientific Research & Development| Vol. 3, Issue 10, 2015 | ISSN (online): 2321-0613
All rights reserved by www.ijsrd.com 471
Parametric Analysis of Single Element U Slot Microstrip Antenna
Mr. R.D. Mengade1 Prof. A.S. Bhalerao2 Prof. V.M. Dhede3
1
PG Student 2,3
Assistant Professor
1,2,3
Department of Electronics and Telecommunication Engineering
1,2,3
JCOE, Kuran, Maharashtra, India
Abstract— In wireless communication system antennas are
the most important element for creating communication link
between source and destination. Microsrtip antennas are used
for mobile and other satellite communication application
because of their light weight, low power handling capacity
and low profile. The modern mobile communication system
requires high gain, wide bandwidth and minimal size
antennas that are capable of providing better performance
over a wide range of frequency spectrum. This requirement
leads to the design of microsrtip patch array antenna. This
paper proposes the parametric analysis of single element U
slot MSA. Low dielectric constant substrates are generally
preferred for maximum radiation. Thus it prefers FR4 as a
dielectric substrate. Desired patch antenna design is
simulated by using high frequency simulation software and
patch antenna is designed as per requirement. Antenna
dimensions such as Length (L), Width (W), and substrate
dielectric constant and parameters like Return Loss, Gain,
impedance and current distribution are calculated using
CAD-FEKO. The antenna has been design to be operated in
the range of 8-12GHz. Hence this antenna is highly suitable
for X-band applications.
Key words: Microstrip patch array Antenna, Surface Current,
VSWR, Radiation Pattern, Efficiency, gain
I. INTRODUCTION
The microstrip antenna is also called as patch antenna. It
contains metallic patch, dielectric substrate and ground plane.
The dielectric substrate is sandwich between patch and
ground plane. Low dielectric constant substrates are generally
preferred for maximum radiation. So this patch is generally
made up from various metals like silver, gold, zinc, etc. But
here we have used copper metal because it is cheap and easily
available in market. The patch metal may have different
shapes Such as, rectangle, square, circle, triangle, circular
ring. But Rectangular patch is commonly used because it is
easy to use, fabricate and cheap. So we are using rectangular
patch in this project. A microstrip antenna is characterized by
its length, width, input impedance, and gain and radiation
patterns.The performance of microstrip antenna determines
by using substrate material, dimension of antenna, feeding
techniques. The four most popular feed techniques used are
the line feeding, coaxial probe (both contacting schemes),
aperture coupling and proximity coupling (both non-
contacting schemes). Microstrip antennas consist of metallic
patch on grounded substrate. The patch is generally made of
conducting material such as copper or gold and can take any
possible shape. The rectangular patch is most popular because
of ease of analysis, fabrication and attractive radiation
characteristics, especially low cross polarization radiation.
The microstrip are low profile, conformable to planar
and nonplanar surfaces, simple and inexpensive to fabricate
using modern printed-circuit technology and very versatile in
terms of resonant frequency, polarization, pattern and
impedance. This rectangular microstrip patch antenna is
designed for wireless communication. These antennas can be
mounted on surface of high performance aircraft, satellite,
missiles, car and handheld mobile telephone.
II. DIAGRAM
Fig. 1: Structure of microstrip patch antenna
For a rectangular patch, the length L of the element is usually
λ0/3 < L < λ0/2, where λ0is the free space wavelength. The
patch is selected to be very thin such that t << λ0(where t is
the patch thickness). The height h of the dielectric substrate
is usually 0.003 λ0 ≤ h ≤ 0.05 λ0. There are numerous
substrates that can be use for design of microstrip antennas,
and their dielectric constants are usually in the range of 2.2 ≤
εr ≤ 12.
III. DESIGN
Fig. 2: Structure of simple microstrip patch antenna

(IJSRD/Vol. 3/Issue 10/2015/096)
Fig. 3: Structure of single slot microstrip patch antenna
Fig. 4: Structure of two slot microstrip patch antenna
Fig. 5: Structure of single element U-Slot microstrip patch
antenna
Design the patch of MSA. The U-slot is composed
of two paralleled vertical rectangular slots and a horizontal
rectangular slot. U-slot plays an important role to control the
wideband behaviour of the coupled patch antenna. There are
three parameters to characterize the slots, namely slot length,
slot position, and slot width. During the process of the
optimization, we can exhibit a wider bandwidth.
A. Theoretical Design
1) Step 1: Calculation of the Width (W):
The width of the Microstrip patch antenna is given
as:
Where;
c - Free space velocity of light, 3 x 108 m/s
fr - Frequency of operation
εr - Dielectric constant
2) Step 2: Calculation of Effective dielectric constant
(εreff):
The effective dielectric constant is:
Where;
εr - Dielectric constant
h - Height of dielectric substrate
W - Width of the patch
3) Step 3: Calculation of the Effective length (Leff):
The effective length is:
Where;
c - Free space velocity of light, 3 x 108 m/s
fr - Frequency of operation
εreff - Effective dielectric constant
4) Step 4: Calculation of actual length of patch (L):
The actual length is obtained by:
L = Leff - 2∆L
Where,
L- Actual length of patch.
Leff - Effective length.
∆L-Small difference between length.
B. Design Values
Patch Shape Rectangular
Frequency 8GHz-12GHz
Dielectric constant of substrate 4.4
Height of substrate 1.6mm
Feeding method Corporate Feed
Polarization Linear
Table 1: Dimensions
IV. SIMULATION RESULTS
The simulated results of antenna are measured using CAD-
FEKO version 7.0. As we know for proper transmission of
signal by antenna, the S11 parameter of antenna should be
less than -10dB
A. Reflection Coefficient-1

Fig. 6: Reflection Coefficient of simple, single slot, two slot,
three slot single element antenna
B. Efficiency-2:
Fig. 7: Efficiency
C. Surface Current-3:
Fig. 8: Surface Current of simple element antenna
D. Surface Current -4
Fig. 9: Surface Current of two slot single element antenna
E. Surface Current -5
Fig. 10: Surface Current of three slot single element antenna

V. COMPARATIVE STUDY OF SIMULATION RESULTS
Fig. 11: Comparison between simple, single slot, two slot,
three slot single element.
VI. APPLICATION
The microstrip patch array antenna used for GPS as well as
RADAR. It is also useful in RFID, Wi-Max applications. In
satellite and aircraft communication it is widely used. It also
used in the WLAN as well as Bluetooth communication. And
also in 3G communication system and for mobile
communication this antenna is widely used.
VII. CONCLUSION
The microsrtip antenna can be simulated by using different
high frequency simulation software. The proposed antenna
can be operated in different frequency band by including the
slots. A wide operating bandwidth for a single element
rectangular microstrip patch antenna can be obtained by
cutting a U-shaped slot on the patch. By using U slot on the
patch antenna can be operated in two or three bands at
different frequency. There are different parameters that affect
the performance of antenna. Dimensions, selection of the
substrate, feed technique and also the operating frequency can
take their position in effecting the performance of microsrtip
antenna
REFERENCES
[1] V. P. Sarin, M. S. Nishamol, D. Tony, C. K. Aanandan, P.
Mohanan, and K. Vasudevan“ABroadband -Strip Fed
Printed Microstrip Antenna”, IEEE Trans Antennas
Propag., vol.59, NO. 1, January 2011,pp.281-284
[2] G. Kumar and K. C. Gupta, “Broad-band microstrip
antenna using additional resonators gap-coupled to the
radiating edges,” IEEE Trans. Antennas Propag., vol. 32,
no. 12, pp. 1375–1379, 1984.
[3] C. K. Aanandan, P. Mohanan, and K. G. Nair, “Broad-
band gap coupled microstrip antenna,” IEEE Trans.
Antennas Propag., vol. 38, no. 10, pp. 1581–1586, 1990.
[4] M. A. Matin, B. S. Sharif, and C. C. Tsimenidis, “Probe
fed stacked patch antenna for wideband applications,”
IEEE Trans. Antennas Propag., vol. 55, no. 8, pp. 2385–
2388, 2007.
[5] M. Gopikrishna, D. D. Krishna, C. K. Aanandan, P.
Mohanan, and K. Vasudevan, “Design of a compact semi-
elliptic monopole slot elements,”IEEE Trans. Antennas
Propag., vol. 55, no. 4, pp. 1196–1199, 2007.
[6] David M. Pozar, “A Review of Microstrip Antennas:
History, Operation, Development, and Applications”,
May 1996
[7] R. Rajkumar, P.Subbulakshmi “Design and
characterization of corporate feed rectangular microstrip
patch array antenna”2013 IEEE International Conference
on Emerging Trends in Communication and
Nanotechnology (ICECCN 2013).
[8] Md.TanvirIshtaiqueulHuque, Md. Kamal Hosain, Md.
Shihabul Islam and Md. Al'AminChowdhury, "Design
and Performance Analysis of Microstrip Array Antennas
with Optimum Parameters for X'band Applications,"
International Journal of Advanced Computer Science and
Applications, Vol. 2, No. 4, 2011.
[9] Constantine A. Balanis, “ANTENNA THEORY”
Analysis and design”, second edition :reprint 2007,John
Wiley Publication.
[10]Yong Liu, Li-Ming Si,MengWei, Pixian Yan, Pengfei
Yang, Hongda Lu, Chao Zheng,Yong Yuan, JinchaoMou,
XinLv, and Housjun Sun, “Some Recent Developments
of MicrostripAntenna”Hindawi Publishing Corporation
International Journal of Antennas and Propagation
Volume 2012, Article ID 428284, 10
pagesdoi:10.1155/2012/428284.
[11]S. D. Lokhande, R. C. Jaiswal, A. S. Bhalerao, “L- Probe
Fed Microstrip Antenna”, International Journal of
Engineering Research & Technology (IJERT) Vol. 2
Issue 6, June - 2013 IJERTIJERT ISSN: 2278-0181.
[12]Steven Weigand, Member, IEEE, Greg H. Huff, Kankan
H. Pan, and Jennifer T. Bernhard, Senior Member, IEEE,
“Analysis and Design of Broad-Band Single-Layer
Rectangular U-Slot Microstrip Patch Antennas”, IEEE
TRANSACTIONS ON ANTENNAS AND
PROPAGATION, VOL. 51, NO. 3, MARCH 2003.
[13]H. Wang, X. B. Huang, and D. G. Fang, Fellow, IEEE,“
A Single Layer Wideband U-Slot Microstrip Patch
Antenna Array”, IEEE ANTENNAS AND WIRELESS
PROPAGATION LETTERS, VOL. 7, 2008.
[14]Ramesh Garg, PrakashBhartia, InderBahl, and
ApisakIttipiboon, Microstrip Antenna Design Handbook.
[15]Girish Kumar, K. P. Ray, “Broadband Microstrip
Antennas”, Artech House, London, 2003

Parametric Analysis of Single Element U Slot Microstrip Antenna

More Related Content

What's hot

Similar to Parametric Analysis of Single Element U Slot Microstrip Antenna

More from IJSRD

Recently uploaded

Parametric Analysis of Single Element U Slot Microstrip Antenna