robotic arms with 3 degree of freedom and
- 1. 1 Outline: Introduction Link Description Link-Connection Description Convention for Affixing Frames to Links Manipulator Kinematics Actuator Space, Joint Space, and Cartesian Space Example: Kinematics of PUMA Robot
- 2. 2 Introduction: Kinematics: Motion without regarding the forces that cause it (Position, Velocity, and Acceleration). Geometry and Time dependent. Rigid links are assumed, connected with joints that are instrumented with sensors to the measure the relative position of the connected links. ◦ Revolute Joint Joint Angle ◦ Prismatic Joint Joint Offset/Displacement Degrees of Freedom # of independent position variables which have to be specified in order to locate all parts of the mechanism Sensor Sensor
- 3. 3 Introduction: Degrees of Freedom Ex: 4-Bar mechanism, # of independent position variables = 1 DoF = 1 Typical industrial open chain serial robot 1 Joint 1 DoF # of Joints # of DoF ≡ End Effector: Gripper, Welding torch, Electromagnetic, etc…
- 4. 4 Introduction: The position of the manipulator is described by giving a description of the tool frame (attached to the E.E.) relative to the base frame (non-moving). Froward kinematics: Given Joint Angles Joint space (θ1,θ1,…,θDoF) Calculate Position & Orientation of the tool frame w. r. t. base frame Cartesian space (x,y,z, and orientation angles)
- 5. 5 Link Description: Links Numbering: n-1 n E.E. Base 0 1 2 In this chapter: - Rigid links are assumed which define the relationship between the corresponding joint axes of the manipulator.
- 6. 6 Link Description: Joint axis (i): Is a line in space or direction vector about which link (i) rotates relative to link (i-1) ai represents the ≡ distance between axes (i & i+1) which is a property of the link (link geometry) ai i ≡ th link length αi angle from axis i to ≡ i+1 in right hand sense about ai. αi link twist ≡ te that a plane normal to ai axis will be parallel to both xis i and axis i+1.
- 7. 7 Link Description Example: consider the link, find link length and twist? a = 7in α = +45o
- 8. 8 Joint Description Intermediate link: Axis i common axis between links i and i-1 ≡ di ≡ link offset distance along this ≡ common axis from one link to the next θi ≡ joint angle the amount ≡ of rotation about this common axis between one link and the other Important di variable if joint i is prismatic ≡ θi variable if joint i is revolute ≡
- 9. 9 Joint Description First and last links: ◦ Use a0 = 0 and α0 = 0. And an and αn are not needed to be defined Joints 1: ◦ Revolute the zero position for θ1 is chosen arbitrarily. d1 = 0. ◦ Prismatic the zero position for d1 is chosen arbitrarily. θ1 = 0. Joints n: the same convention as joint 1. Zero values were assigned so that later calculations will be a simple as possible
- 10. 10 Joint Description Link parameters Hence, any robot can be described kinematically by giving the values of four quantities for each link. Two describe the link itself, and two describe the link's connection to a neighboring link. In the usual case of a revolute joint, θi is called the joint variable, and the other three quantities would be fixed link parameters. For prismatic joints, d1 is the joint variable, and the other three quantities are fixed link parameters. The definition of mechanisms by means of these quantities is a convention usually called the Denavit— Hartenberg notation
- 11. 11 Convention for attaching frames to links A frame is attached rigidly to each link; frame {i} is attached rigidly to link (i), such that: Intermediate link ◦ -axis of frame {i} is coincident with the joint axis (i). ◦ The origin of frame {i} is located where the ai perpendicular intersects the joint (i) axis. ◦ -axis points along ai in the direction from joint (i) to joint (i+1) ◦ In the case of ai= 0, is normal to the plane of and . We define α i as being measured in the right-hand sense about . ◦ is formed by the right-hand rule to complete the ith frame.
- 12. 12 Convention for attaching frames to links First link/joint: ◦ Use frames {0} and {1} coincident when joint variable (1) is zero. (a0 = 0, α0 = 0, and d0 = 0) if joint (1) is revolute (a0 = 0, α0 = 0, and d0 = 0) if joint (1) is revolute Last link/joint: ◦ Revolute joint: frames {n-1} and {n} are coincident when θi = 0. as a result di = 0 (always). ◦ Prismatic joint: frames {n-1} and {n} are coincident when di = 0. as a result θi = 0 (always).
- 13. 13 Convention for attaching frames to links Summary Note: frames attachments is not unique
- 14. 14 Convention for attaching frames to links Example: attach frames for the following manipulator, and find DH parameters…
- 15. 15 Convention for attaching frames to links Example: attach frames for the following manipulator, and find DH parameters… ◦ Determine Joint axes (in this case out of the page) All αi = 0 ◦ Base frame {0} when θ1 = 0 can be determined. ◦ Frame {3} (last link) when θ3= 0 can be determined.
- 16. 16 Convention for attaching frames to links Construct the table:
- 17. 17 Convention for attaching frames to links Previous exam question For the 3DoF manipulator shown in the figure assign frames for each link using DH method and determine link parameters.