Sample elements of computer networking

Elements of Computer Networking Networking Devices
4.1 Glossary 77
Networking
Devices
Chapter
4
4.1 Glossary
 𝐵𝑟𝑖𝑑𝑔𝑒: Network segments that typically use the same communication protocol
use bridges to pass information from one network segment to the other.
 𝐺𝑎𝑡𝑒𝑤𝑎𝑦: When different communications protocols are used by networks,
gateways are used to convert the data from the sender’s
 𝐻𝑢𝑏:Another name for a hub is a concentrator. Hubs reside in the core of the
LAN cabling system. The hub connects workstations and sends every
transmission to all the connected workstations.
 𝑀𝑒𝑑𝑖𝑎 𝐷𝑒𝑝𝑒𝑛𝑑𝑒𝑛𝑡 𝐴𝑑𝑎𝑝𝑡𝑒𝑟: A MDA is a plug-in module allowing selection among
fiber-optic, twisted pair, and coaxial cable.
 𝑀𝑒𝑑𝑖𝑎 𝐹𝑖𝑙𝑡𝑒𝑟: When the electrical characteristics of various networks are
different, media filter adapter connectors make the connections possible.
 𝑀𝑢𝑙𝑡𝑖𝑠𝑡𝑎𝑡𝑖𝑜𝑛 𝐴𝑐𝑐𝑒𝑠𝑠 𝑈𝑛𝑖𝑡: MAUs are special concentrators or hubs for use in
Token Ring networks instead of Ethernet networks.
 𝑀𝑜𝑑𝑒𝑚𝑠: Modem is a device that 𝑐𝑜𝑛𝑣𝑒𝑟𝑡𝑠 digital signals to analog signals and
analog signals to digital signals.
 𝑁𝑒𝑡𝑤𝑜𝑟𝑘 𝐼𝑛𝑡𝑒𝑟𝑓𝑎𝑐𝑒 𝐶𝑎𝑟𝑑:NICs are printed circuit boards that are installed in
computer workstations. They provide the physical connection and circuitry
required to access the network.
 𝑅𝑒𝑝𝑒𝑎𝑡𝑒𝑟: Connectivity device used to regenerate and amplify weak signals,
thus extending the length of the network. Repeaters perform no other action
on the data.
 𝑅𝑜𝑢𝑡𝑒𝑟: Links two or more networks together, such as an Internet Protocol
network. A router receives packets and selects the optimum path to forward
the packets to other networks.
 𝑆𝑤𝑖𝑡𝑐ℎ: A connection device in a network that functions much like a bridge,
but directs transmissions to specific workstations rather than forwarding data
to all workstations on the network.
 𝑇𝑟𝑎𝑛𝑠𝑐𝑒𝑖𝑣𝑒𝑟: The name transceiver is derived from the combination of the
words transmitter and receiver. It is a device that both transmits and receives
signals and connects a computer to the network. A transceiver may be
external or located internally on the NIC.

4.2 End Devices 78
 𝐹𝑖𝑟𝑒𝑤𝑎𝑙𝑙: Firewall provides controlled data access. Firewalls can be hardware
or software based and between networks. These are an essential part of a
network’s security strategy.
4.2 End Devices
In computer networks, the computers that we use on a daily basis are called 𝑛𝑜𝑑𝑒𝑠
(also called ℎ𝑜𝑠𝑡𝑠 or end systems). They are called ℎ𝑜𝑠𝑡𝑠 because they host the
application-level programs such as a Web browser or an electronic-mail program.
Sometimes, they are also called as 𝑒𝑛𝑑 𝑠𝑦𝑠𝑡𝑒𝑚𝑠 because they sit at the edge of the
network connection. A node can be a computer or some other device, such as a
printer. Every node has a unique network address, sometimes called a 𝐷𝑎𝑡𝑎 𝐿𝑖𝑛𝑘
𝐶𝑜𝑛𝑡𝑟𝑜𝑙 (DLC) address or 𝑀𝑒𝑑𝑖𝑎 𝐴𝑐𝑐𝑒𝑠𝑠 𝐶𝑜𝑛𝑡𝑟𝑜𝑙 (MAC) address.
An end device acts as the source (i.e., generates and sends messages) or as the
destination (i.e., receives and consumes content) of the communication process.
In modern networks, a host can act as a client, a server, or both. Software installed on
the host determines which role it plays on the network. Servers are hosts that have
software installed that enables them to provide information and services, like e-mail or
web pages, to other hosts on the network.
Some examples of end devices are:
 Computers, laptops, file servers, web servers.
 Network printers
 VoIP phones
 Security cameras
 Mobile handheld devices
4.3 Intermediary Devices
In addition to the end devices that people are familiar with, computer networks
depends on intermediary devices to provide connectivity. These intermediary devices
work behind the scenes to ensure that data flows across the network. Also, they
connect the individual systems to the network and can connect multiple individual
networks to form an 𝑖𝑛𝑡𝑒𝑟𝑛𝑒𝑡𝑤𝑜𝑟𝑘 (also called 𝐼𝑛𝑡𝑒𝑟𝑛𝑒𝑡). Examples of intermediary
network devices are:
 Network Access Devices (hubs, switches, and wireless access points)
 Internetworking Devices (𝑟𝑜𝑢𝑡𝑒𝑟𝑠)
 Communication Servers and Modems
 Security Devices (𝑓𝑖𝑟𝑒𝑤𝑎𝑙𝑙𝑠)
The management of data as it flows through the network is also a role of the
intermediary devices. These devices use the destination host address, along with
information about the network interconnections, to determine the path that messages
should take through the network. Processes running on the intermediary network
devices perform these functions:
 Regenerate and retransmit data signals
 Maintain information about what pathways exist through the network and
internetwork
 Notify other devices of errors and communication failures
 Direct data along alternate pathways when there is a link failure
 Classify and direct messages according to priorities

4.3 Intermediary Devices 79
 Permit or deny the flow of data, based on security settings
The intermediate devices can be further classified by on their functionality as:
 𝐶𝑜𝑛𝑛𝑒𝑐𝑡𝑖𝑣𝑖𝑡𝑦 𝐷𝑒𝑣𝑖𝑐𝑒𝑠: Connectivity devices are devices used to make physical
network connections. They do 𝑛𝑜𝑡 𝑚𝑎𝑘𝑒 𝑐ℎ𝑎𝑛𝑔𝑒𝑠 to the data or transmission
route. Connectivity devices operate at the physical layer of the OSI model.
 𝐼𝑛𝑡𝑒𝑟𝑛𝑒𝑡𝑤𝑜𝑟𝑘𝑖𝑛𝑔 𝐷𝑒𝑣𝑖𝑐𝑒𝑠: Internetworking devices move data across a network.
They 𝑑𝑖𝑟𝑒𝑐𝑡 data to specific locations within the network and/or 𝑐𝑜𝑛𝑣𝑒𝑟𝑡 data
into alternative formats. Internetworking devices operate at OSI layers above
the physical layer.
4.4 Connectivity Devices
4.4.1 Introduction
Connectivity devices are those devices used to make physical network connections.
Connectivity devices operate at the physical layer of the Open Systems Interconnection
Reference Model (OSI) model. The OSI model describes how computer services and
procedures are standardized.
This standardization allows computers to share information and enables the
interconnection of various networking connectivity devices regardless of vendor.
4.4.2 Network Interface Cards
A 𝑛𝑒𝑡𝑤𝑜𝑟𝑘 𝑖𝑛𝑡𝑒𝑟𝑓𝑎𝑐𝑒 𝑐𝑎𝑟𝑑 is a piece of computer hardware and its main functionality is
to allow a computer to connect to a network. A network interface card is also called
LAN 𝑐𝑎𝑟𝑑, 𝑛𝑒𝑡𝑤𝑜𝑟𝑘 𝑎𝑑𝑎𝑝𝑡𝑒𝑟, 𝑛𝑒𝑡𝑤𝑜𝑟𝑘 𝑎𝑑𝑎𝑝𝑡𝑒𝑟 𝑏𝑜𝑎𝑟𝑑𝑠, 𝑚𝑒𝑑𝑖𝑎 𝑎𝑐𝑐𝑒𝑠𝑠 𝑐𝑎𝑟𝑑𝑠 or simply 𝑁𝐼𝐶.
Regardless of the name, they enable computers to communicate across a network.
With this device, information packets can be transferred back and forth through a
local area network (LAN). It acts a communication source for sending and receiving
data on the network.
NIC provides physical access to a networking medium and often provides a low-level
addressing system through the use of MAC addresses. It allows users to connect to
each other either by using 𝑐𝑎𝑏𝑙𝑒𝑠 or 𝑤𝑖𝑟𝑒𝑙𝑒𝑠𝑠𝑙𝑦.
The network interface card (NIC) is an add-on component for a computer, much like a
video card or sound card is. On most of the systems the NIC is integrated into the
system board. On others it has to be installed into an expansion slot.
Most network interface cards have the 𝐸𝑡ℎ𝑒𝑟𝑛𝑒𝑡 protocol as the language of the data
that is being transferred back and forth. However, network interface cards do not all

necessarily need physical Ethernet or other cables to be functional. Some have
wireless capabilities through including a small 𝑏𝑢𝑖𝑙𝑡-𝑖𝑛 𝑎𝑛𝑡𝑒𝑛𝑛𝑎 that uses radio waves
to transmit information.
The computer must have a software driver installed to enable it to interact with the
NIC. These drivers enable the operating system and higher-level protocols to control
the functions of the adapter.
Each NIC has a unique 𝑚𝑒𝑑𝑖𝑎 𝑎𝑐𝑐𝑒𝑠𝑠 𝑐𝑜𝑛𝑡𝑟𝑜𝑙 (MAC) address to direct traffic. This
unique MAC address ensures that information is only being sent to a specific
computer name and not to multiple ones if not intended to. Circled in the picture
below is an example of an integrated network interface card.
The MAC (Media Access Layer) address, or hardware address, is a 12-digit number
consisting of digits 0-9 and letters A-F. It is basically a hexadecimal number assigned
to the card. The MAC address consists of two pieces: the first signifies which vendor it
comes from, the second is the serial number unique to that manufacturer.
Example MAC addresses:
00-B0-D0-86-BB-F7 01-23-45-67-89-AB 00-1C-B3-09-85-15
The NIC performs the following functions:
 It translates data from the parallel data bus to a serial bit stream for
transmission across the network.
 It formats packets of data in accordance with protocol.
 It transmits and receives data based on the hardware address of the card.
4.4.3 Transceivers
The term 𝑡𝑟𝑎𝑛𝑠𝑐𝑒𝑖𝑣𝑒𝑟 does not necessarily describe a separate network device but
rather embedded in devices such as network cards.
Transceiver is a short name for 𝑡𝑟𝑎𝑛𝑠𝑚𝑖𝑡𝑡𝑒𝑟-𝑟𝑒𝑐𝑒𝑖𝑣𝑒𝑟. It is a device that both transmits
and receives analog or digital signals. The term transceiver is used most frequently to
describe the component in local-area networks (LANs) that actually applies signals
onto the network wire and detects signals passing through the wire. For many LANs,
the transceiver is built into the network interface card (NIC). Older types of networks,
however, require an external transceiver.
The transceiver does not make changes to information transmitted across the
network; it adapts the signals so devices connected by varying media can interpret
them. A transceiver operates at the physical layer of the OSI model.
Technically, on a LAN the transceiver is responsible to place signals onto the network
media and also detecting incoming signals traveling through the same cable. Given the

description of the function of a transceiver, it makes sense that that technology would
be found with network cards (NICs).
4.4.4 Amplifiers and Repeaters
A repeater is an electronic device that receives a signal and retransmits it at a higher
level or higher power, so that the signal can cover longer distances without
degradation.
Transmitter sends a signal containing some information and after travelling some
distance, usually, a signal get weakened (attenuated) due to energy loss in the
medium. Therefore, it should be improved (or 𝑎𝑚𝑝𝑙𝑖𝑓𝑖𝑒𝑑). 𝐴𝑚𝑝𝑙𝑖𝑓𝑖𝑒𝑟 is the circuit which
magnifies the weak signal to a signal with more power.
Sometimes, this signal attenuation happens much before the arrival to the
destination. In this case, signal is amplified and retransmitted with a power gain in
one or more mid points. Those points are called 𝑟𝑒𝑝𝑒𝑎𝑡𝑒𝑟𝑠. Therefore an amplifier is an
essential part of a repeater.
Amplifier
Amplifier is an electronic circuit that increases the power of an input signal. There are
many types of amplifiers ranging from voice amplifiers to optical amplifiers at different
frequencies.
Repeater
The repeater is an electronic circuit that receives a signal and retransmits the same
signal with a higher power. Therefore, a repeater consists of a signal receiver, an
𝑎𝑚𝑝𝑙𝑖𝑓𝑖𝑒𝑟 and a 𝑡𝑟𝑎𝑛𝑠𝑚𝑖𝑡𝑡𝑒𝑟. Repeaters are often used in submarine communication
cables as signal would be attenuated to just a random noise when travelling such a
distance.
Different types of repeaters have different types of configurations depending on the
transmission medium. If the medium is microwaves, repeater may consist of antennas
and waveguides. If the medium is optical it may contain photo detectors and light
emitters.
Difference between an Amplifier and a Repeater
1. Amplifier is used to magnify a signal, whereas repeater is used to receive and
retransmit a signal with a power gain.
2. Repeater has an amplifier as a part of it.
3. Sometimes, amplifiers introduce some noise to the signal, whereas repeaters
contain noise eliminating parts.

Sending Node
Receiving Node
Repeater
6000 meters
𝑇ℎ𝑖𝑐𝑘𝑤𝑖𝑟𝑒 can normally transmit a distance of 500 meters and this can be extended by
introducing repeaters. 𝑇ℎ𝑖𝑛𝑤𝑖𝑟𝑒 can normally transmit a distance of 185 meters, and
can also be extended by using a repeater. This is the advantage to using a repeater. If
a network layout exceeds the normal specifications of cable we can use repeaters to
build network. This will allow for greater lengths when planning cabling scheme.
Repeaters 𝑝𝑒𝑟𝑓𝑜𝑟𝑚 no other action on the data. Repeaters were originally separate
devices. Today a repeater may be a separate device or it may be incorporated into a
hub. Repeaters operate at the physical layer of the OSI model.
4.4.5 Hubs
Hubs are commonly used to connect segments of a LAN. A hub contains multiple
ports. When a packet arrives at one port, it is copied to the other ports so that all
segments of the LAN can see all packets.
A ℎ𝑢𝑏 contains multiple ports. When a packet arrives at one port, it is copied to all
(broadcast) the ports of the hub. When the packets are copied, the destination address
in the frame does not change to a 𝑏𝑟𝑜𝑎𝑑𝑐𝑎𝑠𝑡 address. It does this in a rudimentary
way; it simply copies the data to all of the nodes connected to the hub.
Hub
Hub Hub

The main function of the hub is to broadcast signals to different workstations in a
LAN. General speaking, the term hub is used instead of repeater when referring to the
device that serves as the center of a network.
4.4.6 Modems
Modem is a device that 𝑐𝑜𝑛𝑣𝑒𝑟𝑡𝑠 digital signals to analog signals and analog signals to
digital signals. The word modem stands for 𝑚𝑜𝑑𝑢𝑙𝑎𝑡𝑖𝑜𝑛 and 𝑑𝑒𝑚𝑜𝑑𝑢𝑙𝑎𝑡𝑖𝑜𝑛. The process
of converting digital signals to analog signals is called 𝑚𝑜𝑑𝑢𝑙𝑎𝑡𝑖𝑜𝑛. The process of
converting analog signals to digital signals is called 𝑑𝑒𝑚𝑜𝑑𝑢𝑙𝑎𝑡𝑖𝑜𝑛. Modems are used
with computers to transfer data from one computer to another computer through
telephone lines.
Types of Modem Connections
Modems have two types of connections and they are.
 Analog connection
 Digital connection
Analog Connection
The connection between the modem and the telephone line is called a
𝑎𝑛𝑎𝑙𝑜𝑔 𝑐𝑜𝑛𝑛𝑒𝑐𝑡𝑖𝑜𝑛. It converts digital signals from a computer to analogue signals that
are then sent down the telephone line. A modem on the other end converts the
analogue signal back to a digital signal the computer can understand. A workstation is
connected to an analogue modem. The analogue modem is then connected to the
telephone exchange analogue modem, which is then connected to the internet.
Digital Connection
The connection of modem to computer is called digital connection
Types of Modems
There are two types of modems:
 Internal modems
 External modems
Analog
Modem
Digital
Modem

4.4 Internetworking Devices 84
Internal Modems
It fits into expansion slots inside the computer. It is directly linked to the telephone
lines through the telephone jack. It is normally less inexpensive than external modem.
Its transmission speed is also less external modem.
External Modems
It is the external unit of computer and is connected to the computer through serial
port. It is also linked to the telephone line through a telephone jack. External modems
are expensive and have more operation features and high transmission speed.
Advantages of Modems
 Inexpensive hardware and telephone lines
 Easy to setup and maintain
Disadvantage of Modems
 Very slow performance
4.4 Internetworking Devices
4.4.1 Bridges
Bridge is a device which operates in both the physical and the data link layer of the
OSI reference model. As a physical layer device, it 𝑟𝑒𝑔𝑒𝑛𝑒𝑟𝑎𝑡𝑒𝑠 the signal it receives. As
a data link layer device, the bridge can check the physical (MAC) addresses (𝑠𝑜𝑢𝑟𝑐𝑒
and 𝑑𝑒𝑠𝑡𝑖𝑛𝑎𝑡𝑖𝑜𝑛) contained in the frame.
Bridges can be used to divide a large network into 𝑠𝑒𝑔𝑚𝑒𝑛𝑡𝑠. Bridges contain logic that
allows them to keep the traffic for each 𝑠𝑒𝑔𝑚𝑒𝑛𝑡 𝑠𝑒𝑝𝑎𝑟𝑎𝑡𝑒. When a new frame enters to
a bridge, the bridge not only regenerate the frame but it also checks the address of the
destination and forwards the new copy only to the segment to which the destination
address belongs.
A bridge device 𝑓𝑖𝑙𝑡𝑒𝑟𝑠 data traffic at a network boundary. Bridges reduce the amount
of 𝑡𝑟𝑎𝑓𝑓𝑖𝑐 on a LAN by dividing it into segments. Key features of a bridge are
mentioned below:
Hub
Ethernet LAN
Apple LocalTalk LAN
Bridge

 A bridge operates both in physical and data-link layer
 A bridge uses a table for 𝑓𝑖𝑙𝑡𝑒𝑟𝑖𝑛𝑔/𝑟𝑜𝑢𝑡𝑖𝑛𝑔
 A bridge does not 𝑐ℎ𝑎𝑛𝑔𝑒 the physical (MAC) addresses in a 𝑓𝑟𝑎𝑚𝑒
4.4.1.1 Why Use Bridges?
As an example, imagine for a moment that computers are people in a room. Everyone
is glued to 1 spot and can't move around. If 𝑅𝑎𝑚 wants to talk to 𝑀𝑎𝑟𝑦, he shouts out
"𝐻𝑒𝑦 𝑀𝑎𝑟𝑦" and 𝑀𝑎𝑟𝑦 responds; and a conversation occur as a result.
On a small scale this works quite well. The Internet (as we know it today) is not just 2
or a few people talking directly to each other. The internet is literally billions of
devices. If they were all placed into the same room (network-segment); imagine what
would happen if 𝑅𝑎𝑚 wanted to talk to 𝑀𝑎𝑟𝑦. 𝑅𝑎𝑚 would yell "𝐻𝑒𝑦 𝑀𝑎𝑟𝑦!" and Ram's
voice would be lost in the crowd. Building a room to fit billions of people is equally
ridiculous.
For this reason, networks are separated into smaller segments (smaller rooms) which
allow devices who are in the same segment (room) to talk directly to each other’s. But,
for the devices outside the segment we need some sort of device (router) to pass
messages from one room to the next room. But the vast number of segments (rooms)
means we need some sort of addressing scheme so the various routers in the middle
know how to get a message from 𝑅𝑎𝑚 to 𝑀𝑎𝑟𝑦.
𝑆𝑒𝑔𝑚𝑒𝑛𝑡𝑖𝑛𝑔 a large network with an interconnect device (𝑏𝑟𝑖𝑑𝑔𝑒) has many 𝑎𝑑𝑣𝑎𝑛𝑡𝑎𝑔𝑒𝑠.
Among these are 𝑟𝑒𝑑𝑢𝑐𝑒𝑑 collisions (in an Ethernet network), contained 𝑏𝑎𝑛𝑑𝑤𝑖𝑑𝑡ℎ
utilization, and the ability to filter out unwanted packets. Bridges were created to
allow network administrators to segment their networks transparently. What this
means is that individual stations need not know whether there is a bridge separating
them or not. It is up to the bridge to make sure that packets get properly forwarded to
their destinations. This is the fundamental principle underlying all of the bridging
behaviours we will discuss.
4.4.1.2 Types of Bridges
Several different types of bridges are available for internetworking LANs.
1. 𝑇𝑟𝑎𝑛𝑠𝑝𝑎𝑟𝑒𝑛𝑡 𝐵𝑎𝑠𝑖𝑐 𝐵𝑟𝑖𝑑𝑔𝑒 [𝑇𝑟𝑎𝑛𝑠𝑝𝑎𝑟𝑒𝑛𝑡 𝐹𝑜𝑟𝑤𝑎𝑟𝑑𝑖𝑛𝑔 𝐵𝑟𝑖𝑑𝑔𝑒]: Places incoming
frame onto all outgoing ports 𝑒𝑥𝑐𝑒𝑝𝑡 original incoming port.
2. 𝑇𝑟𝑎𝑛𝑠𝑝𝑎𝑟𝑒𝑛𝑡 𝐿𝑒𝑎𝑟𝑛𝑖𝑛𝑔 𝐵𝑟𝑖𝑑𝑔𝑒: Stores the origin of a frame (from which port) and
later uses this information to place frames to that port.
3. 𝑇𝑟𝑎𝑛𝑠𝑝𝑎𝑟𝑒𝑛𝑡 𝑆𝑝𝑎𝑛𝑛𝑖𝑛𝑔 𝐵𝑟𝑖𝑑𝑔𝑒: Uses a subset of the LAN topology for a loop-free
operation.
4. 𝑆𝑜𝑢𝑟𝑐𝑒 𝑅𝑜𝑢𝑡𝑖𝑛𝑔 𝐵𝑟𝑖𝑑𝑔𝑒: Depends on routing information in frame to place the
frame to an outgoing port.
4.4.1.2.1 Transparent Basic Bridges [Transparent Forwarding Bridge]
The simplest type of bridge is called the 𝑡𝑟𝑎𝑛𝑠𝑝𝑎𝑟𝑒𝑛𝑡 𝑏𝑎𝑠𝑖𝑐 𝑏𝑟𝑖𝑑𝑔𝑒. It is called
𝑡𝑟𝑎𝑛𝑠𝑝𝑎𝑟𝑒𝑛𝑡 because the nodes using a bridge are unaware of its presence. This bridge
receives traffic coming in on each port and stores the traffic until it can be transmitted
on the outgoing ports. It will not forward the traffic from the port from which it was
received.
The bridge does not make any conversion of the traffic. The bridge forwards (𝑟𝑒𝑐𝑒𝑖𝑣𝑒
and 𝑠𝑢𝑏𝑠𝑒𝑞𝑢𝑒𝑛𝑡𝑙𝑦 𝑡𝑟𝑎𝑛𝑠𝑚𝑖𝑡) frames from one LAN to another. Obviously, the bridge
forwards all frames like a 𝑟𝑒𝑝𝑒𝑎𝑡𝑒𝑟.

Transparent Bridge Forwarding
If the destination address is present in the forwarding database (table) already created,
the packet is forwarded to the port number to which the destination host is attached.
If it is not present, forwarding is done on all parts (𝑓𝑙𝑜𝑜𝑑𝑖𝑛𝑔). This process is called
𝑏𝑟𝑖𝑑𝑔𝑒 𝑓𝑜𝑟𝑤𝑎𝑟𝑑𝑖𝑛𝑔.
Bridge forwarding operation is explained with the help of flowchart.
In the figure above, consider three nodes A, B, and C. Assume each node sends frames
to all other nodes. The source addresses A, B are observed to be on network LAN-1,
while the address of node C will be observed to be on network LAN-2.
Basic functions of the bridge forwarding are mentioned below.
1. If the source address is 𝑛𝑜𝑡 present in the forwarding table, the bridge 𝑎𝑑𝑑𝑠
the source address and corresponding interface to the table. It then checks
the destination address to determine if it is in the table.
2. If the destination address is listed in the table, it determines if the destination
address is on the same LAN as the source address. If it is, then the bridge
𝑑𝑖𝑠𝑐𝑎𝑟𝑑𝑠 the frame since all the nodes have already received the frame.
3. If the destination address is listed in the table but is on a different LAN than
the source address, then the frame is forwarded to that LAN.
4. If the destination address is not listed in the table, then the bridge forwards
the frame to all the LANs except the one that which originally received the
frame. This process is called 𝑓𝑙𝑜𝑜𝑑𝑖𝑛𝑔.
In some bridges, if the bridge has not accessed an address in the forwarding table over
a period of time, the address is removed to free up memory space on the bridge. This
process is referred to as 𝑎𝑔𝑖𝑛𝑔.
Packets with a source A and destination B are received and discarded, since the node
B is directly connected to the LAN-1, whereas packets from A with a destination C are
forwarded to network LAN-2 by the bridge.
Forward frame to all
LANs except X
No
Yes
Yes No
Frame Received without
error on port X
Destination
found in
table?
Forward frame to
correct LAN
Direction
= port X?
Count discarded
frames
Node-B Node-CNode-A
LAN-1 Bridge LAN-2

4.4.1.2.2 Transparent Bridge Learning
To learn which addresses are in use, and which ports (interfaces on the bridge) are
closest to, the bridge observes the headers of received frames. By examining the MAC
source address of each received frame, and recording the port on which it was
received, the bridge may learn which addresses belong to the computers connected via
each port. This is called 𝑙𝑒𝑎𝑟𝑛𝑖𝑛𝑔.
The learned addresses are stored in the 𝑖𝑛𝑡𝑒𝑟𝑓𝑎𝑐𝑒 𝑎𝑑𝑑𝑟𝑒𝑠𝑠 𝑡𝑎𝑏𝑙𝑒 (𝑑𝑎𝑡𝑎𝑏𝑎𝑠𝑒) associated
with 𝑒𝑎𝑐ℎ port (𝑖𝑛𝑡𝑒𝑟𝑓𝑎𝑐𝑒). Once this table has been setup, the bridge examines the
destination address of all received frames; it then scans the interface tables to see if a
frame has been received from the same address (i.e. a packet with a source address
matching the current destination address).
At the time of installation of a transparent bridge, the table is empty. When a packet is
encountered, the bridge checks its source address and build up a table by associating
a source address with a port address to which it is connected. The flowchart explains
the learning process.
Table Building
The table building up operation is illustrated in figure. Initially the table is empty.
Address Port
1. When node A sends a frame to node D, the bridge does not have any entry for
either D or A. The frame goes out from all three ports. The frame floods the
Yes
Add source to table
with direction and
timer
NoSource
found in
table?
Update direction
and timer
Port-1
Port-2
LAN-3
Node-F
Node-E
Node-A
Node-C
Node-B
LAN-1
LAN-2
Node-D
Bridge
Port-3

network. However, by looking at the source address, the bridge learns that
node A must be located on the LAN connected to port 1.
This means that frame destined for A (in future), must be sent out through
port 1. The bridge adds this entry to its table. The table has its first entry now.
Address Port
A 1
2. When node E sends a frame to node A, the bridge has an entry for A, so it
forwards the frame only to port 1. There is no flooding. Also, it uses the source
address of the frame (E in this case), to add a second entry to the table.
Address Port
A 1
E 3
3. When node B sends a frame to C, the bridge has no entry for C, so once again
it floods the network and adds one more entry to the table.
Address Port
A 1
E 3
B 1
4. The process of learning continues as the bridge forwards frames.
Loop Problem
Forwarding and learning processes work without any problem as long as there is no
redundant bridge in the system. On the other hand, redundancy is desirable from the
viewpoint of reliability, so that the function of a failed bridge is taken over by a
redundant bridge.
The existence of redundant bridges creates the so-called loop problem as shown
figure. Assuming that after initialization tables in both the bridges are empty let us
consider the following steps:
 𝑆𝑡𝑒𝑝 1: Node A sends a frame to node B. Both the bridges forward the frame to
LAN 1 and update the table with the source address of A.
 𝑆𝑡𝑒𝑝 2: Now there are two copies of the frame on LAN-1. The copy sent by
Bridge-A is received by Bridge-B and vice versa. As both the bridges have no
information about node B, both will forward the frames to LAN-2.
 𝑆𝑡𝑒𝑝 3: Again both the bridges will forward the frames to LAN-1 because of the
lack of information of the node B in their database and again Step-2 will be
repeated, and so on.
Node-B
LAN-1
LAN-2
Node-A
Bridge-A Bridge-B

So, the frame will continue to 𝑙𝑜𝑜𝑝 around the two LANs indefinitely.
4.4.1.2.3 Transparent Spanning Bridges
As seen in previous section, redundancy creates loop problem in the system and it is
undesirable. To prevent loop problem, the IEEE (Institute of Electrical and Electronics
Engineers) specification requires that the bridges use a special topology. Such a
topology is known as 𝑠𝑝𝑎𝑛𝑛𝑖𝑛𝑔 𝑡𝑟𝑒𝑒 (a graph where there is no loop) topology.
The methodology for setting up a spanning tree is known as 𝑠𝑝𝑎𝑛𝑛𝑖𝑛𝑔 𝑡𝑟𝑒𝑒 𝑎𝑙𝑔𝑜𝑟𝑖𝑡ℎ𝑚.
𝑆𝑝𝑎𝑛𝑛𝑖𝑛𝑔 𝑡𝑟𝑒𝑒 𝑎𝑙𝑔𝑜𝑟𝑖𝑡ℎ𝑚 creates a tree out of a graph. Without changing the physical
topology, a logical topology is created that overlay on the physical by using the
following steps:
1. Select a bridge as 𝑟𝑜𝑜𝑡-𝑏𝑟𝑖𝑑𝑔𝑒, which has the smallest ID.
2. Select root ports for all the bridges, except for the root bridge, which has least-
cost path (say, minimum number of hops) to the root bridge.
3. Choose a 𝑑𝑒𝑠𝑖𝑔𝑛𝑎𝑡𝑒𝑑 bridge, which has least-cost path to the 𝑟𝑜𝑜𝑡-𝑏𝑟𝑖𝑑𝑔𝑒, in
each LAN.
4. Select a port as 𝑑𝑒𝑠𝑖𝑔𝑛𝑎𝑡𝑒𝑑 𝑝𝑜𝑟𝑡 that gives least-cost path from the 𝑑𝑒𝑠𝑖𝑔𝑛𝑎𝑡𝑒𝑑
𝑏𝑟𝑖𝑑𝑔𝑒 to the 𝑟𝑜𝑜𝑡 bridge.
5. Mark the designated port and the root ports as 𝑓𝑜𝑟𝑤𝑎𝑟𝑑𝑖𝑛𝑔 ports and the
remaining ones as 𝑏𝑙𝑜𝑐𝑘𝑖𝑛𝑔 ports.
An Example
Let us walk through the below example for running the spanning tree algorithm on.
Note that some of the LAN segments have a cost 3 times that of others. The following
convention is used for the remaining discussion:
 DC means designated cost for a LAN segment
 Bridge-# means bridge number
 A number around a bridge is a port number
3
Root Bridge
1
LAN-3 DC = 1
LAN-2DC = 3
LAN-6DC = 1
LAN-1 DC = 3
Bridge-2
1
2
Bridge-1
1
2
Bridge-6
2
LAN-4 DC = 3
LAN-5 DC = 3
Bridge-5
1
2
Bridge-3
1
2
Bridge-4
1
2
3

Step 1 of the algorithm is already shown in the first picture: Bridge 1 is chosen as the
𝑟𝑜𝑜𝑡 𝑏𝑟𝑖𝑑𝑔𝑒 since all the bridges are assumed to have the same priority. The tie is
broken by choosing the bridge with the smallest ID number.
Next, we determine the root path cost (RPC) for each port on each bridge 𝑜𝑡ℎ𝑒𝑟 𝑡ℎ𝑎𝑛 the
𝑟𝑜𝑜𝑡 bridge. Then each bridge other than the root chooses its port with the lowest RPC
as the root port (RP). Ties are broken by choosing the 𝑙𝑜𝑤𝑒𝑠𝑡-𝑛𝑢𝑚𝑏𝑒𝑟𝑒𝑑 port. The root
port is used for all control messages from the root bridge to this particular bridge.
𝑆𝑎𝑚𝑝𝑙𝑒 𝑅𝑃𝐶 𝑐𝑎𝑙𝑐𝑢𝑙𝑎𝑡𝑖𝑜𝑛: Consider port 1 of Bridge-5. Between it and root bridge we
have to traverse at least LAN-3 and LAN-4, with costs 1 and 3 respectively. Total cost
is 4. Thus RPC = 4 for port 1 of Bridge-5.
Next, step 3 of the algorithm is to select a designated bridge and a designated port on
this bridge for each LAN segment. This is the bridge that gives the least cost (DPC,
designated port cost) for getting between this LAN segment and the root bridge. The
port on this bridge by which we attach this LAN segment is called the 𝑑𝑒𝑠𝑖𝑔𝑛𝑎𝑡𝑒𝑑 𝑝𝑜𝑟𝑡
(DP). If there is a tie for the lowest DPC, the bridge with the smallest ID number is
chosen.
The root bridge is always the designated bridge for the LAN segments directly attached
to it. The ports by which the root bridge attaches to the LAN segments are thus
designated ports. We assume that no LAN segment attaches to the root bridge by more
than 1 port. Since a root port cannot be chosen as a designated port, do not waste
time even considering root ports as possible designated ports.
In the drawing on the next page, we see that LAN-1, LAN-2, and LAN-3 are directly
attached to the root bridge via ports 1, 2, and 3 respectively on the root bridge. Thus
we only need to consider LAN-4, LAN-5, and LAN-6. LAN-4 could use either port 2 on
Bridge-3 or port 3 on Bridge-4 as its designated port. The DPC for each is 1 since
anything sent from LAN-4 through such a port goes across LAN-3 to the root bridge
and the cost of LAN-3 is just 1.
RPC = 7
3
Root Bridge
1
LAN-3 DC = 1
LAN-2DC = 3
LAN-6DC = 1
LAN-1 DC = 3
Bridge-2
1
2
Bridge-1
1
2
Bridge-6
2
LAN-4 DC = 3
LAN-5 DC = 3
Bridge-5
1
2
Bridge-3
1
2
Bridge-4
1
2
3
RPC = 3
RPC = 1
RPC = 1 RPC = 1
RPC = 4 RPC = 4
RPC = 4
RPC = 3
RPC = 2
RP
RP
RP
RP
RP

Since we have a tie for the DP we choose the one on the lowest number bridge. That
means that Bridge-3 is the designated bridge and its port 2 is the designated port for
LAN-3. For LAN-5 there is only one port that could be chosen, so the designated port
for LAN-5 is port 2 on Bridge-5 and the designated bridge is Bridge-5. There is no
choice for LAN-6 either as one port is a root port. Thus the designated port for S6 is
the other one: port 2 on Bridge-4.
Finally, in step 4 each port that is not a root port or designated port is set to be in a
blocking state so that no traffic can flow through it. The blocked ports are X-ed out
RP 3
Root Bridge
1
LAN-3 DC = 1
LAN-2DC = 3
LAN-6DC = 1
LAN-1 DC = 3
Bridge-2
1
2
Bridge-1
1
2
Bridge-6
2
LAN-4
DC = 3
LAN-5 DC = 3
Bridge-5
1
2
Bridge-3
1
2
Bridge-4
1
2
3
DPC = 1
DPC = 1 DPC = 1
DPC = 4
DP
RP
RP
RP
RP
DP
DP
DP
DP
DP DPC = 1
3
Root Bridge
1
LAN-3 DC = 1
LAN-2DC = 3
LAN-6DC = 1
LAN-1 DC = 3
Bridge-2
1
2
Bridge-1
1
2
Bridge-6
2
LAN-4
DC = 3
LAN-5 DC = 3
Bridge-5
1
2
Bridge-3
1
2
Bridge-4
1
2
3
Block
Block
DP
RP
RP
RP
RP
DP
DP
DP
DP
DP
RP
Block

above. This, then, produces our spanning tree (no loops). To better see the spanning
tree, the picture can be redrawn as shown on the next page, with the root bridge as
the root of the tree.
4.4.1.2.4 Translational Bridges
Translational bridges are a type of transparent bridge that connects LANs that use
different protocols at the data link and physical layers, for example, FDDI (Fiber
Distributed Data Interface) and Ethernet.
4.4.1.2.5 Source Routing Bridges
In source routing bridges, the routing operation is determined by the source host and
the frame specifies which route the 𝑓𝑟𝑎𝑚𝑒 to follow. A host can discover a route by
sending a 𝑑𝑖𝑠𝑐𝑜𝑣𝑒𝑟𝑦 frame, which spreads through the entire network using all
possible paths to the destination.
Each frame gradually gathers addresses as it goes. The destination responds to each
frame and the source host chooses an appropriate route from these responses. For
example, a route with minimum ℎ𝑜𝑝-𝑐𝑜𝑢𝑛𝑡 can be chosen. Whereas transparent
bridges do not modify a frame, a source routing bridge adds a routing information field
to the frame. Source routing approach provides a shortest path at the cost of extra
burden on the network.
Source route bridging is used in token ring networks. A source route bridge links two
or more rings together. There are fundamental characteristics in how a source route
bridge transmits a frame between rings. A source route bridge does not create and
Bridge
Ethernet LAN
FDDI
Ring LAN
Bridge
Token
Ring LAN
Token
Ring LAN
Token
Ring LAN
Bridge

maintain forwarding tables. The decision to forward or drop a frame is based on
information provided in the frame.
The destination station is responsible for maintaining routing tables that define a
route to all workstations on the network. The source workstation is responsible for
determining the path of a frame to its destination. If no route information is available,
then the source station has the ability to perform route discovery to learn the potential
paths that can be taken.
4.4.2 Switches
𝑆𝑤𝑖𝑡𝑐ℎ is a device that filters and forwards packets between LAN segments. Switch
works at the layer 2 of the OSI model. The main purpose of the switch is to
concentrate connectivity while making data transmission more efficient. Think of the
switch as something that combines the connectivity of a hub with the traffic regulation
of a bridge on each port. Switches makes decisions based on MAC addresses.
A switch is a device that performs switching. Specifically, it forwards and filters OSI
layer 2 datagrams (chunk of data communication) between ports (connected cables)
based on the MAC addresses in the packets.
As discussed earlier, a hub forwards data to all ports, regardless of whether the data
is intended for the system connected to the port. This mechanism is inefficient; and
switches tries to address this issue to some extent. This is different from a hub in that
it only forwards the datagrams to the ports involved in the communications rather
than all ports connected. Strictly speaking, a switch is not capable of routing traffic
based on IP address (layer 3) which is necessary for communicating between network
segments or within a large or complex LAN.
4.4.2.1 How a Switch works?
Rather than forwarding data to all the connected ports, a switch forwards data only to
the port on which the destination system is connected. It looks at the Media Access
Control (MAC) addresses of the devices connected to it to determine the correct port.
Switch
Sending Node Receiving Node
Data
Data

A MAC address is a unique number that is stamped into every NIC. By forwarding
data only to the system to which the data is addressed, the switch decreases the
amount of traffic on each network link dramatically.
4.4.2.2 Switching Methods
We can specify one of 𝑓𝑜𝑢𝑟 possible forwarding methods for each port in a switch:
1. Cut-through
2. Fragment-free
3. Store-and-forward
4. Adaptive
4.4.2.2.1 Store and Forward Switching
In 𝑠𝑡𝑜𝑟𝑒 and 𝑓𝑜𝑟𝑤𝑎𝑟𝑑 switching, Switch copies each of the complete Ethernet frame
into the switch memory and computes a Cyclic Redundancy Check (CRC) for errors. If
a Cyclic Redundancy Check (CRC) error is found, the Ethernet frame is dropped and if
there is no Cyclic Redundancy Check (CRC) error, the switch forwards the Ethernet
frame to the destination device. Store and Forward switching can cause delay in
switching since Cyclic Redundancy Check (CRC) is calculated for each Ethernet frame.
4.4.2.2.2 Cut-through Switching
In 𝑐𝑢𝑡-𝑡ℎ𝑟𝑜𝑢𝑔ℎ switching, the switch copies into its memory only the destination MAC
address (first 6 bytes of the frame) of the frame before making a switching decision. A
switch operating in cut-through switching mode reduces delay because the switch
starts to forward the Ethernet frame as soon as it reads the destination MAC address
and determines the outgoing switch port. Problem related with cut-through switching
is that the switch may forward bad frames.
4.4.2.2.3 Fragment-Free Switching
𝐹𝑟𝑎𝑔𝑚𝑒𝑛𝑡-𝑓𝑟𝑒𝑒 switching is an advanced form of cut-through switching. The switches
operating in cut-through switching read only up to the destination MAC address field
in the Ethernet frame before making a switching decision. The switches operating in
fragment-free switching read at least 64 bytes of the Ethernet frame before switching it
to avoid forwarding Ethernet runt frames (Ethernet frames smaller than 64 bytes).
4.4.2.2.4 Adaptive switching
𝐴𝑑𝑎𝑝𝑡𝑖𝑣𝑒 𝑠𝑤𝑖𝑡𝑐ℎ𝑖𝑛𝑔 mode is a user-defined facility to maximize the efficiency of the
switch. Adaptive switching starts in the default switch forwarding mode we have
selected. Depending on the number of errors (say, CRC errors) at that port, the mode
changes to the 𝑏𝑒𝑠𝑡 of the other two switching modes.
4.4.3 Routers
4.4.3.1 What is Router?
𝑅𝑜𝑢𝑡𝑒𝑟𝑠 are 𝑝ℎ𝑦𝑠𝑖𝑐𝑎𝑙 devices that join multiple 𝑛𝑒𝑡𝑤𝑜𝑟𝑘𝑠 together. Technically, a router
is a Layer 3 device, meaning that it connects two or more networks and that the router
operates at the network layer of the OSI model.
Routers maintain a table (called 𝑟𝑜𝑢𝑡𝑖𝑛𝑔 𝑡𝑎𝑏𝑙𝑒) of the available routes and their
conditions and use this information along with distance and cost algorithms to

determine the best route for a given packet. Typically, a packet may travel through a
number of network points with routers before arriving at its destination.
The purpose of the router is to examine incoming packets (layer 3), chose the best
path for them through the network, and then switches them to the proper outgoing
port. Routers are the most important traffic controlling devices on large networks.
Routers are networking devices that forward data packets between networks using
headers and 𝑓𝑜𝑟𝑤𝑎𝑟𝑑𝑖𝑛𝑔 𝑡𝑎𝑏𝑙𝑒𝑠 to determine the best path to forward the packets.
Routers also provide interconnectivity between 𝑙𝑖𝑘𝑒 and 𝑢𝑛𝑙𝑖𝑘𝑒 media (networks which
use different protocols).
4.4.3.2 Understanding Concepts of Routers
As an example, assume that we want to send a postcard just based on person names
(with minimum information). For example, 𝐵𝑖𝑙𝑙 𝐺𝑎𝑡𝑒s [USA], 𝑆𝑎𝑐ℎ𝑖𝑛 𝑇𝑒𝑛𝑑𝑢𝑙𝑘𝑎𝑟 [India] or
𝐴𝑙𝑏𝑒𝑟𝑡 𝐸𝑖𝑛𝑠𝑡𝑒𝑖𝑛 [USA] it would be routed to them due to their fame; no listing of the
street address or the city name would be necessary. The postal system can do such
routing to famous personalities, depending on the name alone.
In an Internet, a similar discussion is possible: 𝑟𝑒𝑎𝑐ℎ any 𝑤𝑒𝑏𝑠𝑖𝑡𝑒 anywhere in the
world without knowing where the site is currently located. Not only that, it is possible
to do so very efficiently, within a matter of a few seconds.
4.4.3.2.1 What is Network Routing?
How is this possible in a communication network, and how can it be done so quickly?
The answer to this question is 𝑁𝑒𝑡𝑤𝑜𝑟𝑘 𝑟𝑜𝑢𝑡𝑖𝑛𝑔. 𝑁𝑒𝑡𝑤𝑜𝑟𝑘 𝑟𝑜𝑢𝑡𝑖𝑛𝑔 is the ability to send a
unit of information from source to destination by finding a path through the network,
and by doing efficiently and quickly.
4.4.3.2.2 What is Addressing?
First, we start with a key and necessary factor, called 𝑎𝑑𝑑𝑟𝑒𝑠𝑠𝑖𝑛𝑔. In many ways,
addressing in a network has similarities to postal addressing in the postal system. So,
we will start with a brief discussion of the postal addressing system to relate them.
A typical postal address that we write on a postcard has several components—the
name of the person, followed by the street address with the house number (ℎ𝑜𝑢𝑠𝑒
𝑎𝑑𝑑𝑟𝑒𝑠𝑠), followed by the city, the state name, and the postal code. If we take the

processing view to route the postcard to the right person, we essentially need to
consider this address in the reverse order of listing, i.e., start with the postal code,
then the city or the state name, then the house address, and finally the name of the
person.
You may notice that we can reduce this information somewhat; that is, you can just
use the postal code and leave out the name of the city or the name of the state, since
this is redundant information. This means that the information needed in a postal
address consists of three main parts: the postal code, the street address (with the
house number), and the name.
A basic routing problem in the postal network is as follows:
1. The postcard is first routed to the city or the geographical region where the
postal code is located.
2. Once the card reaches the postal code, the appropriate delivery post office for
the address specified is identified and delivered to.
3. Next, the postman or postwoman delivers the postcard at the address, without
giving much consideration to the name listed on the card.
4. Rather, once the card arrives at the destination address, the residents at this
address take the responsibility of handing it to the person addressed.
The routing process in the postal system is broken down to three components:
 How to get the card to the specific postal code (and subsequently the post
office),
 How the card is delivered to the destination address, and
 Finally, how it is delivered to the actual person at the address.
If we look at it in another way, the place where the postcard originated in fact does not
need to know the detailed information of the street or the name to start with; the
postal code is sufficient to determine to which geographical area or city to send the
card. So, we can see that postal routing uses address hierarchy for routing decisions.
An advantage of this approach is the decoupling of the routing decision to multiple
levels such as the postal code at the top, then the street address, and so on. An
important requirement of this hierarchical view is that there must be a way to divide
the complete address into multiple distinguishable parts to help with the routing
decision.
Now, consider an electronic communication network; for example, a critical
communication network of the modern age is the Internet. Naturally, the first question
that arises is: how does addressing work for routing a unit of information from one
point to another, and is there any relation to the postal addressing hierarchy that we
have just discussed? Second, how is service delivery provided? In the next section, we
address these questions.
4.4.3.2.3 Addressing and Internet Service: An Overview
In many ways, Internet addressing has similarities to the postal addressing system.
The addressing in the Internet is referred to as 𝐼𝑛𝑡𝑒𝑟𝑛𝑒𝑡 𝑃𝑟𝑜𝑡𝑜𝑐𝑜𝑙 (IP) 𝑎𝑑𝑑𝑟𝑒𝑠𝑠𝑖𝑛𝑔. An IP
address defines 𝑡𝑤𝑜 parts: one part that is similar to the postal code and the other
part that is similar to the house address; in Internet terminology, they are known as
the 𝑛𝑒𝑡𝑖𝑑 and the ℎ𝑜𝑠𝑡𝑖𝑑, to identify a network and a host address, respectively.
A host is the end point of communication in the Internet and where a communication
starts. A host is a generic term used for indicating many different entities; the most
common ones are a web-server, an email server, desktop, laptop, or any computer we
use for accessing the Internet. A 𝑛𝑒𝑡𝑖𝑑 identifies a contiguous block of addresses.

4.4.3.2.4 Network Routing: An Overview
In the previous section, we provided a broad overview of addressing and transfer
mechanisms for data in Internet communication services. Briefly, we can see that
eventually packets are to be routed from a source to a destination. Such packets may
need to traverse many cross-points, similar to traffic intersections in a road
transportation network. Cross-points in the Internet are known as 𝑟𝑜𝑢𝑡𝑒𝑟𝑠.
A router’s functions are to read the destination address marked in an incoming IP
packet, to consult its internal information to identify an outgoing link to which the
packet is to be forwarded, and then to forward the packet. Similar to the number of
lanes and the speed limit on a road, a network link that connects two routers is
limited by how much data it can transfer per unit of time, commonly referred to as the
band-width or capacity of a link; it is generally represented by a data rate, such as
1.54 megabits per second (Mbps). A network then carries traffic on its links and
through its routers to the eventual destination; traffic in a network refers to packets
generated by different applications, such as web or email.
Note: For more about IP Addressing and routing, refer 𝐼𝑃 𝐴𝑑𝑑𝑟𝑒𝑠𝑠𝑖𝑛𝑔 and 𝑅𝑜𝑢𝑡𝑖𝑛𝑔
𝑃𝑟𝑜𝑡𝑜𝑐𝑜𝑙𝑠 chapters.
4.4.3.3 Types of Routers
Depending on the role that routers perform, routers can be classified in many different
ways.
4.4.3.3.1 Interior Routers
𝐼𝑛𝑡𝑒𝑟𝑖𝑜𝑟 routers work within networks. These routers handle packets travelling
between nodes on the same Intra-network. An interior router is used to divide a large
network into more easily manageable subnetworks. It can keep one part of a network
secure from another and it can allow different technologies, for example, Ethernet and
token ring, to be used in the same network.
4.4.3.3.2 Border Routers
𝐵𝑜𝑟𝑑𝑒𝑟 routers exist on one network and their function is to connect that network with
outside networks, including the Internet. They discover routes between the interior
network and others and they handle incoming and outgoing traffic.
Internet
Exterior Routers Border Routers Interior Routers

4.4.3.3.3 Exterior Routers
𝐸𝑥𝑡𝑒𝑟𝑖𝑜𝑟 routers are most common on the Internet. They do not exist on a particular
network but rather in the space between networks where data passes through on its
way to its destination. Exterior routers do not store routes to particular hosts; but
they store routes to other 𝑟𝑜𝑢𝑡𝑒𝑟𝑠. Their primary role is to receive packets and then
forward them in the direction of their destination.
4.4.4 Gateways
The term 𝑔𝑎𝑡𝑒𝑤𝑎𝑦 is used in networking to describe the 𝑔𝑎𝑡𝑒 to the Internet. The
𝑔𝑎𝑡𝑒𝑤𝑎𝑦 controls traffic that travels from the inside network to the Internet and
provides security from traffic that wants to enter the inside network from the Internet.
A network gateway is an internetworking system which joins two networks that use
different base protocols. A network gateway can be implemented completely in
software, completely in hardware, or as a combination of both. Depending on the types
of protocols they support, network gateways can operate at any level of the OSI model.
Since a gateway (by definition) appears at the edge of a network, related capabilities
like firewalls tend to be integrated with it. On home networks, a router typically serves
as the network gateway although ordinary computers can also be configured to
perform equivalent functions.
As mentioned earlier, the Internet is not a single network but a collection of networks
that communicate with each other through gateways. A gateway is defined as a system
that performs relay functions between networks, as shown in figure above. The
different networks connected to each other through gateways are often called
𝑠𝑢𝑏𝑛𝑒𝑡𝑤𝑜𝑟𝑘𝑠, because they are a smaller part of the larger overall network.
With TCP/IP, all interconnections between physical networks are through gateways.
An important point to remember for use later is that gateways route information
packets based on their destination network name, not the destination machine.
Gateways are completely transparent to the user.
4.4.1 Default Gateway
The default gateway is needed only for systems that are part of an internetwork (in the
above figure, note that two subnetworks connected to same gateway). Data packets
with a destination IP address not on the local subnet are forwarded to the default
gateway. The default gateway is normally a computer system or router connected to
the local subnet and other networks in the internetwork.
If the default gateway becomes unavailable, the system cannot communicate outside
its own subnet, except for with systems that it had established connections with prior
to the failure.
Sub-Network Sub-Network
Sub-Network
Sub-Network
Sub-Network
Gateway
Gateway
Gateway

4.4.2 Multiple Gateways
If the default gateway becomes unavailable, data packets cannot reach their
destination. 𝑀𝑢𝑙𝑡𝑖𝑝𝑙𝑒 𝑔𝑎𝑡𝑒𝑤𝑎𝑦𝑠 can be used to solve this problem.
4.4.3 Difference between Gateway and Router
4.4.3.1 Gateway
The 𝑘𝑒𝑦 𝑑𝑖𝑓𝑓𝑒𝑟𝑒𝑛𝑐𝑒 between gateway and router is, gateway it is defined as a network
node that allows a network to interface with another network with different protocols.
A router is a device that is capable of sending and receiving data packets between
computer networks, also creating an overlay network.
Gateways and routers are two words are often confused due to their similarities. Both
gateways and routers are used to regulate traffic into more separate networks.
However, these are two different technologies and are used for different purposes.
The term gateway can be used to define two different technologies: gateway and
default gateway. These two terms should not be confused. In terms of communications
network, gateway it is defined as a network node that allows a network to interface
with another network with different protocols. In simple terms, gateway allows two
different networks to communicate with each other. It contains devices such as
impedance protocol translators, rate converters, or signal translators to allow system
interoperability.
A protocol translation/mapping gateway interconnects networks that have different
network protocol technologies. Gateways acts as a network point that acts as an
entrance to another network. The gateway can also allow the network to connect the
computer to the internet. Many routers are available with the gateway technology,
which knows where to direct the packet of data when it arrives at the gateway.
Gateways are often associated with both routers and switches.
Default gateway is a computer or a computer program that is configured to perform
the tasks of a traditional gateway. These are often used by ISP or computer servers
that act as gateway between different systems. When getting an internet connection,
an ISP usually provides a device that allows the user to connect to the Internet; these
devices are called 𝑚𝑜𝑑𝑒𝑚𝑠. In organizational systems a computer is used as a node to
connect the internal networks to the external networks, such as the Internet.
4.4.3.2 Router
A router is a device that is capable of sending and receiving data packets between
computer networks, also creating an overlay network. The router connects two or more
data line, so when a packet comes in through one line, the router reads the address
information on the packet and determines the right destination, it then uses the
information in its routing table or routing policy to direct the packet to the next
network. On the internet, routers perform 𝑡𝑟𝑎𝑓𝑓𝑖𝑐 𝑑𝑖𝑟𝑒𝑐𝑡𝑖𝑛𝑔 functions. Routers can also
be wireless as well as wired.
The most common type of routers is small office or home routers. These are used for
passing data from the computer to the owner's cable or DSL modem, which is
connected to the internet. Other routers are huge enterprise types that connect large
businesses to powerful routers that forward data to the Internet.
When connected in interconnected networks, the routers exchange data such as
destination addresses by using a dynamic routing protocol. Each router is responsible
for building up a table that lists the preferred routes between any two systems on the

interconnected networks. Routers can also be used to connect two or more logical
groups of computer devices known as subnets. Routers can offer multiple features
such as a DHCP server, NAT, Static Routing, and Wireless Networking.
These days’ routers are mostly available with built-in gateway systems make it easier
for users with them not having to buy separate systems.
4.4.5 Firewalls
The term firewall was derived from 𝑐𝑖𝑣𝑖𝑙 𝑒𝑛𝑔𝑖𝑛𝑒𝑒𝑟𝑖𝑛𝑔 and intended to 𝑝𝑟𝑒𝑣𝑒𝑛𝑡 the 𝑠𝑝𝑟𝑒𝑎𝑑
of fire from one 𝑟𝑜𝑜𝑚 to another. From the computer security perspective, the Internet
is an unsafe environment; therefore 𝑓𝑖𝑟𝑒𝑤𝑎𝑙𝑙 is an excellent metaphor for network
security.
A firewall is a system designed to prevent unauthorized access to or from a private
network. Firewalls can be implemented in either hardware or software form, or a
combination of both. Firewalls prevent unauthorized users from accessing private
networks. A firewall sits between the two networks, usually a private network and a
public network such as the Internet.
Connecting a computer or a network of computers may become targets for malicious
software and hackers. A firewall can offer the security that makes a computer or a
network less vulnerable.
Note: For more details, refer 𝐹𝑖𝑟𝑒𝑤𝑎𝑙𝑙𝑠 section in 𝑁𝑒𝑡𝑤𝑜𝑟𝑘 𝑆𝑒𝑐𝑢𝑟𝑖𝑡𝑦 chapter.
4.4.6 Differences between Hubs, Switches, and Routers
Today most routers have something combining the features and functionality of a
router and switch/hub into a single unit. So conversations regarding these devices
can be a bit misleading — especially to someone new to computer networking.
The functions of a router, hub and a switch are all quite different from one another,
even if at times they are all integrated into a single device. Let's start with the hub and
Internal Network
Internet
(Unsecure)
F
I
R
E
W
A
L
L

the switch since these two devices have similar roles on the network. Each serves as a
central connection for all of your network equipment and handles a data type known
as frames. Frames carry the data. When a frame is received, it is amplified and then
transmitted on to the port of the destination PC. The big difference between these two
devices is in the method in which frames are being delivered.
In a hub, a frame 𝑏𝑟𝑜𝑎𝑑𝑐𝑎𝑠𝑡𝑠 to every one of its ports. It doesn't matter that the frame
is only destined for one port. The hub cannot distinguish which port a frame should
be sent to. Broadcasting it on every port ensures that it will reach its intended
destination. This places a lot of traffic on the network and can lead to poor network
response times.
Additionally, a 10/100Mbps hub must share its bandwidth with each and every one of
its ports. So, when only one PC is broadcasting, it will have access to the maximum
available bandwidth. If, however, multiple PCs are broadcasting, then that bandwidth
will need to be divided among all of those systems, which will degrade performance.
A switch, however, keeps a record of the 𝑀𝐴𝐶 addresses of all the devices connected to
it. With this information, a switch can identify which system is sitting on which port.
So, when a frame is received, it knows exactly which port to send it to, without
significantly increasing network response times. And, unlike a hub, a 10/100Mbps
switch will allocate a full 10/100Mbps to each of its ports. So regardless of the
number of PCs transmitting, users will always have access to the maximum amount of
bandwidth. It's for these reasons why a switch is considered to be a much better
choice than a hub.
𝑅𝑜𝑢𝑡𝑒𝑟𝑠 are completely different devices. Where a hub or switch is concerned with
transmitting frames, a router's job, as its name implies, is to route packets to other
networks until that packet ultimately reaches its destination. One of the key features
of a packet is that it not only contains data, but the destination address of where it's
going.
A router is typically connected to at least two networks, commonly two Local Area
Networks (LANs) or Wide Area Networks (WAN) or a LAN and its ISP's network, for
example, your PC or workgroup and EarthLink. Routers are located at gateways, the
places where two or more networks connect. Using headers and forwarding tables,
routers determine the best path for forwarding the packets. Router use protocols such
as ICMP to communicate with each other and configure the best route between any
two hosts.
Question 1: In modern packet-switched networks, the source host segments long,
application-layer messages (for example, an image or a music file) into smaller
packets and sends the packets into the network. The receiver then reassembles
the packets back into the original message. We refer to this process as 𝑚𝑒𝑠𝑠𝑎𝑔𝑒
𝑠𝑒𝑔𝑚𝑒𝑛𝑡𝑎𝑡𝑖𝑜𝑛. Figure shows the end-to-end transport of a message with and
without message segmentation. Consider a message that is 9.0106 bits long that
is to be sent from source to destination in figure. Suppose each link in the figure
is 1.5 Mbps. Ignore propagation, queuing, and processing delays.
Problems and Questions with Answers
Source
Packet
Switch
Destination
Packet
Switch
No Segmentation
Full Message

A) Consider sending the message from source to destination without message
segmentation. How long does it take to move the message from the source host to
the first packet switch? Keeping in mind that each switch uses store-and-forward
packet switching, what is the total time to move the message from source host to
destination host?
B) Now suppose that the message is segmented into 5,000 packets, with each
packet being 1,500 bits long. How long does it take to move the first packet from
source host to the first switch? When the first packet is being sent from the first
switch to the second switch, the second packet is being sent from the source host
to the first switch. At what time will the second packet be fully received at the first
switch?
C) How long does it take to move the file from source host to destination host
when message segmentation is used? Compare this result with your answer in
part (A) and comment.
𝐴𝑛𝑠𝑤𝑒𝑟:
A) Time to send message from source host to first packet switch =
9×106
1.5×106
sec = 6 sec.
With store-and-forward switching, the total time to move message from source host to
destination host = 6 sec × 3 hops = 18 sec.
B) Time to send 1st packet from source host to first packet switch =
1.5×103
1.5×106 sec = 1
msec.
Time at which second packet is received at the first switch = 1.5 × 106
time at which
first packet is received at the second switch = 2 × 1 msec = 2 msec.
C) Time at which 1st packet is received at the destination host = 1 msec × 3 hops = 3
msec . After this, every 1msec one packet will be received; thus time at which last
(5000 𝑡ℎ
) packet is received = 3 msec + 4999 × 1 msec = 5.002 sec.
It can be seen that delay in using message segmentation is significantly less (more
than
1
3
rd).
Question 2: For the following statement, indicate whether the statement is True or
False.
Switches exhibit lower latency than routers.
𝐴𝑛𝑠𝑤𝑒𝑟: True. No routing table look-up, no delays associated with storing data
𝑞𝑢𝑒𝑢𝑖𝑛𝑔, bits flow through the switch essentially as soon as they arrive.
Question 3: Packet switches have queues while circuit switches do not. Is it true or
false?
𝐴𝑛𝑠𝑤𝑒𝑟: False. Routers have queues; switches do not, even though the packet switch
must have more memory than a circuit switch to receive a full packet before it can
forward it on.
Question 4: Consider the arrangement of learning bridges shown in the following
figure. Assuming all are initially empty, give the forwarding tables for each of the
bridges B1-B4 after the following transmissions:
Segment
Source
Packet
Switch
Destination
Packet
Switch
With Segmentation

D sends to C; A sends to D; C sends to A
𝐴𝑛𝑠𝑤𝑒𝑟: When D sends to C, all bridges see the packet and learn where D is. However,
when A sends to D, the packet is routed directly to D and B3 does not learn where A
is. Similarly, when C sends to A, the packet is routed by B2 towards B1 only, and B4
does not learn where C is.
The forwarding table for Bridge B1:
Destination Next Hop
A A-Interface
C B2-Interface
D B2-Interface
A B1-Interface
C B3-Interface
D B4-Interface
C C-Interface
D B2-Interface
A B2-Interface
D D-Interface
Question 5: Which type of bridge observes network traffic flow and uses this
information to make future decisions regarding frame forwarding?
A) Remote B) Source routing C) Transparent D) Spanning tree
𝐴𝑛𝑠𝑤𝑒𝑟: C
Question 6: Learning network addresses and converting frame formats are the
function of which device?
A) Switch B) Hub C) MAU D) Bridge
𝐴𝑛𝑠𝑤𝑒𝑟: D
Question 7: The device that can operate in place of a hub is a:
A) Switch B) Bridge C) Router D) Gateway
𝐴𝑛𝑠𝑤𝑒𝑟: A
Question 8: Which of the following is NOT true with respective to a transparent bridge
and a router?
A) Both bridge and router selectively forward data packets
B2
B4
C
B1
B3
A
D

B) A bridge uses IP addresses while a router uses MAC addresses
C) A bridge builds up its routing table by inspecting incoming packets
D) A router can connect between a LAN and a WAN.
𝐴𝑛𝑠𝑤𝑒𝑟: B. Bridge is the device which work at data link layer whereas router works at
network layer. Both selectively forward packets, build routing table and connect
between LAN and WAN but since bridge works at data link it uses MAC addresses to
route whereas router uses IP addresses.

Elements of Computer Networking LAN Technologies
5.1 Introduction 105
LAN Technologies
Chapter
5
5.1 Introduction
The bottom two layers of the Open Systems Interconnection (OSI) model deal with the
physical structure of the network and the means by which network devices can send
information from one device on a network to another.
The data link layer controls how data packets are sent from one node to another.
Application Layer
Presentation Layer
Session Layer
Transport Layer
Network Layer
Data Link Layer
Physical Layer
Application Layer
Presentation Layer
Session Layer
Transport Layer
Network Layer
Data Link Layer
Physical Layer
Data Data
ReceiverSender
Physical Link

5.2 Types of Network Links 106
5.2 Types of Network Links
There are two types of network links: 𝑝𝑜𝑖𝑛𝑡-𝑡𝑜-𝑝𝑜𝑖𝑛𝑡 links, and 𝑏𝑟𝑜𝑎𝑑𝑐𝑎𝑠𝑡 links.
5.2.1 Broadcasting Network Links
Broadcast is a method of sending a signal where multiple nodes may hear a single
sender node. As an example, consider a conference room with full of people. In this
conference room, a single person starts saying some information loudly.
During that time, some people may be sleeping, and may not hear what person is
saying. Some people may not be sleeping, but not paying attention (they are able to
hear the person, but choose to ignore). Another group of people may not only be
awake, but be interested in what is being said. This last group is not only able to hear
the person speaking, but is also listening to what is being said.
In this example, we can see that a single person is broadcasting a message to all
others that may or may not be able to hear it, and if they are able to hear it, may
choose to listen or not.
5.2.1.1 Simplex Broadcasting Network
Radio and TV stations are a good examples of everyday life 𝑏𝑟𝑜𝑎𝑑𝑐𝑎𝑠𝑡 𝑛𝑒𝑡𝑤𝑜𝑟𝑘𝑠. In this
case the radio/TV stations are a type of communications called 𝑆𝑖𝑚𝑝𝑙𝑒𝑥. In a simplex
type of communication, data is only expected to flow in one direction.
5.2.1.2 Half-Duplex Broadcasting Network
Conference-room meetings are another everyday example of a broadcast network. In
this example, everyone may speak to everyone else, but when more than one person
speaks, interference (collision) from multiple conversations may make it impossible to
listen to more than one conversation even though we can hear both conversations. In
this conference-room example, we can see parties are able to share access to a
common media (human voice as sound through the air.) They compete for access to
speak, but for the most part, only one person speaks at a time for everyone to hear.
This is an example of a type of communications called ℎ𝑎𝑙𝑓-𝑑𝑢𝑝𝑙𝑒𝑥.
5.2.1.3 Full-Duplex Broadcasting Network
Let us consider the singing competition where we can see a group of singers
attempting to sing in Harmony. They can each speak separately on their own, but if
they speak on different topics, the conveyed information for any of them may be lost
by each other. This is an example of another type of communication called 𝑓𝑢𝑙𝑙-𝑑𝑢𝑝𝑙𝑒𝑥.
This means that they are not only able to speak, but listen at the same time they are
speaking. All of them will speak and listen at the same time. How is this possible? In
order to sing in harmony, each singer must be able to hear the frequencies being used
by the other singers, and strive to create a frequency with their voice that matches the
desired frequency to create that harmony.
This feed-back of each singer to listen to the collective, and possibly key into a specific
singer's voice is used by them as they sing to create the exact frequency needed, and
ensure their timing is the same as the rest of the singers. All members are able to hear
all other members, and speak at the same time. They are all acting as a 𝑓𝑢𝑙𝑙-
𝑑𝑢𝑝𝑙𝑒𝑥 communications in a broadcast network.

5.3 Medium Access Control Techniques 107
5.2.2 Point-to-Point Network Links
𝑃𝑜𝑖𝑛𝑡-𝑡𝑜-𝑃𝑜𝑖𝑛𝑡 is a method of communication where one node speaks to another node.
A woman in a restaurant whispers to her husband a message. Nobody else in the
restaurant knows what was said. The conversation was only between them.
5.2.2.1 Simplex Point-to-Point Network
An example of a very simple 𝑠𝑖𝑚𝑝𝑙𝑒𝑥 point-to-point network could be a doorbell (the
circuit.) When the doorbell button is depressed at the front door, a signal is passed to
bell which performs its functions to announce the button has been depressed. The bell
does not send a message to button. The message travels only in one direction and
takes place between the button and the bell.
5.2.2.2 Half-Duplex Point-to-Point Network
As an example, let us assume that we have a couple who are openly affectionate, sat
on a bench in a park, and holding hands under a blanket.
Also, assume that this couple has their own code in holding hands for speaking to
each other. For example, 3 squeezes maps to 𝐼 𝐿𝑜𝑣𝑒 𝑌𝑜𝑢 and 4 squeezes of the hand
maps to 𝐼 𝐿𝑜𝑣𝑒 𝑌𝑜𝑢 𝑇𝑜𝑜. The wife squeezes her husband's hand 3 times. He gets this
message, and smiles (acknowledging the receipt of the message) and then returns a
new message of 4 squeezes. She smiles (acknowledging her receipt of the message she
felt.) If both parties attempted to squeeze each other's hands at the same time, then
the number of squeezes may be confused. So we can see each party may speak
through squeezing each other’s hands, but only one may speak at a time.
This conversation takes place only between these two people. Here we see point-to-
point and ℎ𝑎𝑙𝑓-𝑑𝑢𝑝𝑙𝑒𝑥.
5.2.2.3 Full-Duplex Point-to-Point Network
Data can travel in both directions simultaneously. There is no need to switch from
transmit to receive mode like in half duplex. Full-duplex network operates like a two-
way, two-lane street. Traffic can travel in both directions at the same time.
5.3 Medium Access Control Techniques
As we have seen, networks can be divided into two types:
1) S𝑤𝑖𝑡𝑐ℎ𝑒𝑑 communication network (also called 𝑝𝑜𝑖𝑛𝑡-𝑡𝑜-𝑝𝑜𝑖𝑛𝑡, 𝑝𝑒𝑒𝑟-𝑡𝑜-𝑝𝑒𝑒𝑟, and
𝑠𝑤𝑖𝑡𝑐ℎ𝑒𝑑): 𝑝𝑒𝑒𝑟-𝑡𝑜-𝑝𝑒𝑒𝑟 communication is performed with the help of
transmission lines such as multiplexers and switches.
2) 𝐵𝑟𝑜𝑎𝑑𝑐𝑎𝑠𝑡 communication network: In this we have a medium which is shared
by a number of nodes. 𝐵𝑟𝑜𝑎𝑑𝑐𝑎𝑠𝑡 is a method of sending a signal where
multiple nodes may hear a single sender node.
A point-to-point link consists of a single sender on one end of the link, and a single
receiver at the other end of the link. Many link-layer protocols have been designed for
Networks
Switched Networks Broadcast Networks

5.3 Medium Access Control Techniques 108
point-to-point links; PPP (point-to-point protocol) and HDLC (High-level Data Link
Control) are two such protocols.
Now, let us consider a different kind of scenario in which we have a medium which is
shared by a number of users.
Any user can broadcast the data into the network. Now whenever it is broadcasted
obviously there is a possibility that several users will try to broadcast simultaneously.
This problem can be addressed with medium access control techniques.
Now question arises how different users will send through the shared media. It is
necessary to have a protocol or technique to regulate the transmission from the users.
That means, at a time only one user can send through the media and that has to be
decided with the help of Medium Access Control (MAC) techniques. Medium access
control techniques determines the next user to talk (i.e., transmit into the channel).
A good example is something we are familiar with - a classroom - where teacher(s) and
student(s) share the same, single, broadcast medium. As humans, we have evolved a
set of protocols for sharing the broadcast channel ("Give everyone a chance to speak."
"Don't speak until you are spoken to." "Don't monopolize the conversation." "Raise
your hand if you have question." "Don't interrupt when someone is speaking." "Don't
fall asleep when someone else is talking.").
Similarly, computer networks have protocols called 𝑚𝑢𝑙𝑡𝑖𝑝𝑙𝑒 𝑎𝑐𝑐𝑒𝑠𝑠 protocols. These
protocols control the nodes data transmission onto the shared broadcast channel.
There are various ways to classify multiple access protocols. Multiple access protocols
can be broadly divided into four types; random, round-robin, reservation and
channelization. These four categories are needed in different situations. Among these
four types, channelization technique is static in nature. We shall discuss each of them
one by one.
Shared Medium
Token Passing
Broadcast Multiple Access Techniques
Static Channelization Techniques Dynamic Medium Access Techniques
TDMA
FDMA
CDMA
Random Access Techniques
ALOHA
CSMA
CSMA/CD
CSMA/CA
Round-Robin
Polling
Reservation
R-ALOHA

5.4 Random Access Techniques 109
5.4 Random Access Techniques
Random access method is also called 𝑐𝑜𝑛𝑡𝑒𝑛𝑡𝑖𝑜𝑛-𝑏𝑎𝑠𝑒𝑑 access. In this method, no
station is assigned to control another. Random MAC techniques can be further divided
into four different types; ALOHA, CSMA, CSMA/CD and CSMA/CA.
When each node has a fixed flow of information to transmit (for example, a data file
transfer), reservation based access methods are useful as they make an efficient use of
communication resources. If the information to be transmitted is bursty in nature, the
reservation-based access methods are not useful as they waste communication
resources.
Random-access methods are useful for transmitting short messages. The random
access methods give freedom for each 𝑛𝑜𝑑𝑒 to get access to the network whenever the
user has information to send.
5.4.1 ALOHA
Aloha protocol was developed by 𝐴𝑏𝑟𝑎𝑚𝑠𝑜𝑛 at 𝑈𝑛𝑖𝑣𝑒𝑟𝑠𝑖𝑡𝑦 𝑜𝑓 𝐻𝑎𝑤𝑎𝑖𝑖. In the 𝐻𝑎𝑤𝑎𝑖𝑖𝑎𝑛
language, Aloha means 𝑎𝑓𝑓𝑒𝑐𝑡𝑖𝑜𝑛, 𝑝𝑒𝑎𝑐𝑒, and 𝑐𝑜𝑚𝑝𝑎𝑠𝑠𝑖𝑜𝑛. University of Hawaii consists
of a number of islands and obviously they cannot setup wired network in these
islands. In the University of Hawaii, there was a centralized computer and there were
terminals distributed to different islands. It was necessary for the central computer to
communicate with the terminals and for that purpose 𝐴𝑏𝑟𝑎𝑚𝑠𝑜𝑛 developed a protocol
called 𝐴𝑙𝑜ℎ𝑎.
Central node and terminals (stations) communicate by using a wireless technique
called 𝑝𝑎𝑐𝑘𝑒𝑡 𝑟𝑎𝑑𝑖𝑜. Each of these stations can transmit by using 𝑢𝑝𝑙𝑖𝑛𝑘 frequency
which is 𝑟𝑎𝑛𝑑𝑜𝑚 access shared by all the terminals. After receiving the data, the
central node retransmits by using a 𝑑𝑜𝑤𝑛𝑙𝑖𝑛𝑘 frequency and that will be received by all
terminals.
There are two different types of ALOHA:
1. Pure ALOHA
2. Slotted ALOHA
5.4.1.1 Pure Aloha
The first version of protocol given by 𝐴𝑚𝑑𝑟𝑎𝑠𝑜𝑛 works like this:
1. If a node has data to send, send the data
2. If the message collides with another transmission, try resending later
3. In case of collision, sender waits random time before retrying
…Terminal-1
Terminal-2 Terminal-3
Terminal-4
Central Node
Random Access
Broadcast

5.4 Random Access Techniques 110
This simple version is also called 𝑝𝑢𝑟𝑒 𝐴𝐿𝑂𝐻𝐴. Note that, in Pure ALOHA, sender does
not check whether the channel is busy before transmitting.
5.4.1.1.1 Frames in Pure ALOHA
Pure ALOHA assumes all frames have the same length. A shared communication
system like ALOHA requires a method for handling collisions. Collisions will occur
when two or more systems try to send data at the same time. In the ALOHA system, a
node transmits whenever data is available to send. If another node transmits at the
same time, a collision occurs, and the frames that were transmitted are lost. However,
a node can listen to broadcasts on the medium, even its own, and determine whether
the frames were transmitted.
As shown in diagram, whenever two frames try to occupy the channel at the same
time, there will be a collision and both will be damaged. If first bit of a new frame
overlaps with just the last bit of a frame almost finished, both frames will be totally
destroyed and both will have to be retransmitted.
5.4.1.1.2 Pure ALOHA Protocol
Pure ALOHA uses two different frequencies for data transfers. The central node
broadcasts packets to everyone on the outbound (also called 𝑑𝑜𝑤𝑛𝑙𝑖𝑛𝑘) channel, and
the terminals sends data packets to the central node on the inbound (also called
𝑢𝑝𝑙𝑖𝑛𝑘) channel.
If data was received correctly at the central node, a short acknowledgment packet was
sent to the terminal; if an acknowledgment was not received by a terminal after a
short wait time, it would automatically retransmit the data packet after waiting a
randomly selected time interval. This acknowledgment mechanism was used to detect
and correct for collisions created when two terminals both attempted to send a packet
at the same time.
 In pure ALOHA, the stations transmit frames whenever they have data to
send.
 When two or more stations transmit at the same time, there will be a collision
and the frames will get destroyed.
 In pure ALOHA, whenever any station transmits a frame, it expects the
acknowledgement from the receiver.
 If acknowledgement is not received within specified time, the station assumes
that the frame has been destroyed.
B
C
D
A Frame-A.1
Frame-B.1
Frame-C.1
Frame-D.1
Frame-A.2
Frame-B.2
Frame-D.2
Frame-C.2
Collision Durations
Time

Sample elements of computer networking

More Related Content

What's hot (20)

Similar to Sample elements of computer networking (20)

Recently uploaded (20)

Sample elements of computer networking