Transmission Line Constraints
Download as PPTX, PDF1 like827 views
The document discusses transmission line constraints, highlighting thermal limitations, dielectric limits, and loadability issues, emphasizing that power transfer capability is restricted by thermal and voltage constraints. It explains that short lines are primarily limited by thermal constraints while long lines face voltage constraints, and other factors like ambient conditions and reactive power demand also play a critical role. The significance of managing overvoltages and ensuring adequate reactive power absorption is underscored to maintain system stability.
Transmission Line Constraints
- 2. Thermal limitations • Excessive temperature may result in expansion and resultant sag of conductors causing decreased clearance to ground. Temperature extremes also reduces mechanical strength of aluminum. • Since thermal time constants are large, it is useful to distinguish between steady state and transient thermal ratings. • Function of i) ambient temperature, ii) Wind conditions, iii)Condition of conductor, iv) Conductor type and v) ground clearance.
- 3. • ACSR (aluminum conductor steel reinforced) Moose Conductor (520 mm2): For an ambient temperature of 40 degree C, and a maximum conductor temperature of 75 degree C, ampacity is 700 A (approx.). Typically, two moose conductors form a bundle of 400 kV line so that the total ampacity is 1400A for such a line. • For AAAC (all aluminum alloy conductor) of 520 mm2 : With an ambient temperature of 40 degree C, and a maximum conductor temperature of 85 degree C, ampacity is 850 A (approx.) for a 400 kV line. • Thermal ratings are a strong function of ambient conditions (wind flows, solar radiation) and absorption and emmisivity of the conductor material. • Evaluate the actual ampacity during real time operation (season to season, day to day or hour to hour).
- 4. Dielectric Limits • Exceeding dielectric limits (maximum electric field strength) results in failure of insulation, causing faults. • Electric fields may be excessive (due to overvoltage) under low loading conditions on long ac transmission lines Ferranti Effect) or during abnormal conditions like lightning strokes. • Deviation of voltages beyond certain limits can also be considered to be an unacceptable compromise on the quality of power being supplied to consumers. Low or high voltages can also damage electrical equipments. • Given a nominal voltage rating, a steady state overvoltage of about 10% is often permissible. Shunt reactors (inductors) are often connected in shunt on transmission lines to prevent overvoltages under low loading. If permanently connected to a line, however, they may excessively reduce the voltages during heavy load conditions.
- 5. • . Voltages and reactive power demand of transmission lines are affected by: line parameters, length of line and power transfer • Line Parameters: Line parameters are dependent on the conductor dimensions and relative placement. The surge impedance of most overhead lines is around 250- 350 ohms whereas it is 30-50 ohms for cables. • Typical positive sequence inductance and capacitance parameters for a 400 kV overhead line: L = 1.044mH/km, C = 12 nF/km. For EHV lines , X/R ratio is large. The resistance per unit length of this line = 0.0296 ohm / km. • For a 400 kV paper-insulated lead-covered(PILC) cable, typical positive sequence parameters are: L = 0.78 mH/km, C = 0.95 uF/km.
- 6. Voltage variation in AC transmission line Important results for lossless lines such as EHV lines: • Voltage profile along the line is flat only if R= Zc is connected at receiving end (SIL). Under this situation, there is no demand of reactive power from either sending or receiving ends. Loads are decided by consumers and not by a system operator. As such, this exact condition is practically never met although it is ideal. • If voltage at both ends is maintained at 1.0 pu, the voltage tends to sag as we move towards the midpoint if Ps > SIL. The line absorbs reactive power. If Ps < SIL, voltage swells and the line generates reactive power. • For a line which has one end maintained at 1.0 pu but kept open- circuited at the other end, overvoltage will be evident at the open end. All these effects are very prominent for long lines.
- 7. • Cables have very high SIL. The current at SIL usually exceeds the thermal rating of a cable. Therefore a cable is invariably loaded below its SIL. Cables, therefore, generate reactive power and usually voltages can be very high at low loading levels, especially for long lengths. Besides this, cables are much costlier than overhead lines and are more "unforgiving" towards overloads. Therefore, cables of lengths exceeding 30-40km are rarely used for ac transmission. • Due to voltage problems, underwater cable transmission and bulk transfer over very long distances is carried out using DC transmission technology.
- 9. Line Loadability in AC lines • For preventing over voltages at light loads, it is necessary to have devices for absorbing reactive power (e.g. shunt reactors) not only at either end of a long line but even at intermediate points. • Generators connected at the ends of the line have limited reactive power absorption capability as defined by their capability curves. If transmission redundancy exists (i.e., parallel transmission paths exist), then a very lightly loaded long line may be tripped to avoid overvoltage. However, this may be detrimental to system security if some additional line trippings take place due to faults. • If shunt reactors are permanently connected, they result in large sags in the voltage under heavy loading conditions. Moreover, reactive power demanded by long transmission lines under these situations may be excessive and may lead to system-wide low voltage conditions.
- 10. • Compensation by connecting (lumped) capacitors in series and shunt effectively reduce the line reactance and increase the shunt susceptance, thereby decreasing the surge impedance. Thus the effective SIL of a capacitor compensated line is higher than an uncompensated line. This increases the loadability of a long line. • Since total conductor cross-sectional area for EHV lines is mainly decided by electric field considerations (corona), these lines have large thermal capabilities, much in excess of the SIL. For long EHV lines, one cannot deviate much from SIL due to voltage constraints. Therefore, the thermal limit of a long EHV line is not the key limiting factor. However, thermal limit is the main limiting factor for short lines (< 100 km) where voltage constraints are not violated even for large deviations from SIL.
- 12. Summary • Power transfer capability of a ac line is restricted by thermal and voltage constraints. • Short lines are limited by thermal constraints. • Long lines are limited by voltage constraints. Stability constraints are also important for long ac lines.