UTTAR PRADESH POWER
TRANSMISSION CARPORATION
LIMITED ( U.P.P.T.C.L )
INTRODUCTION
The creation of Uttar Pradesh Power Corporation Ltd.
(UPPCL) on January 14, 2000 is the result of power sector
reforms and restructuring in UP (India) which is the focal
point of the Power Sector, responsible for planning and
managing the sector through its transmission,
distribution and supply of electricity.
UPPCL will be professionally managed utility supplying
reliable and cost efficient electricity to every citizen of the
state through highly motivated employees and state of art
technologies, providing an economic return to our owners
and maintaining leadership in the country.
132KV Chakia Substation
 132KV Chakia Substation is one important
substation of UPPTCL. It is situated at Chakia
Shahupuri in under LUCKNOW.
The whole substation is divided in to two parts –
132 KV Switchyard & 33 KV Switchyard.
The incoming lines for Chakia
1.Shahupuri (132KV line)
2.Robartsganj (132KV line)
The outgoing lines of Chakia
1.ilia Feeder
2.Kaudihar Canal
3.Chakia town
4.Chakia roller
132KV SINGLE LINE DIAGRAM
TRASFORMER
Two transformer are used in 20MVA
We know, MVA = 1.732VI
For 20MVA (HV) For 20MVA (LV)
20*10^3=1.732*132*I 20*10^3=1.732*33*I
I= 87.47A(HV) I=350A(LV)
Lightning Arrester
A lightning arrester is a device used
on electrical power systems
and telecommunications systems to protect
the insulation and conductors of the system
from the damaging effects of lightning.
 The typical lightning arrester has a high-
voltage terminal and a ground terminal.
When a lightning surge travels along the
power line to the arrester, the current from
the surge is diverted through the arrestor, in
most cases to earth.
current transformer
A current transformer (CT) is used for
measurement of alternating electric
currents.
When current in a circuit is too high to
apply directly to measuring instruments, a
current transformer produces a reduced
current accurately proportional to the
current in the circuit, which can be
conveniently connected to measuring and
recording instruments.
A current transformer isolates the
measuring instruments from what may be
very high voltage in the monitored circuit.
Potential transformers
Potential transformers (PT) (also
called voltage transformers (VT)) are
a parallel connected type of
instrument transformer.
They are designed to present
negligible load to the supply being
measured and have an accurate
voltage ratio and phase relationship
to enable accurate secondary
connected metering.
The PT is typically described by its
voltage ratio from primary to
secondary. Standard secondary
voltage ratings are 120 volts and
70 volts, compatible with standard
measuring instruments
Circuit Breaker
A circuit breaker is an automatically
operated electrical switch designed to protect
an electrical circuit from damage caused by
overload or short circuit. Its basic function is to detect a
fault condition and interrupt current flow
According to their arc quenching media
the circuit breaker can be divided as-
1.Oil circuit breaker
2.Air circuit breaker
3.SF6 circuit breaker
4.Vacuum circuit breaker
1.oil circuit breaker
2.Air circuit breaker
3.SF6 circuit breaker
4.Vacuum circuit breaker
Isolators
It is an off-load device.
It disconnects or isolates the circuit from the main power
supply.
Even though, isolators is a switch, it is not used as a
normal on off switch.
Isolators may provide additional safety features like, when
switched off the trapped charge will be ground through a
ground terminal in the isolator.
CAPACITOR BANK
The load on the power system is
varying being high during morning
and low in evening which increases
the load current. This result in the
decreased power factor.
The low power factor is mainly due
to the fact most of the power loads
are inductive and therefore take
lagging currents.
Capacitor bank accomplishes
following operations:
Supply reactive power
Increases terminal voltage
Improve power factor
FUSE
A fuse is a short piece of wire
or thin strip which melts when
excessive current through it for
sufficient time. It is inserted in
series with the circuit under
normal operating conditions; the
fuse element is at a nature
below its melting point.
Therefore it carries the normal
load current overheating. It is
worthwhile to note that a fuse
performs both detection and
interruption functions.
BUS COUPLER
The bus coupler consists of
circuit breaker and isolator. Each
generator and feeder may be
connected to either main bus bar
or spar bus bar with the help of
bus coupler. Repairing,
maintenance and testing of
feeder circuit or other section.
Bus coupler is a device which is
used switch from one bus to the
other without any interruption in
power supply and without
creating hazardous arcs. It is
achieved with the help of circuit
breaker and isolators.
RELAY
When a failure occurs on any
part of the system, it must be
quickly detected and
disconnected from the system.
Rapid disconnection of faulted
apparatus limits the amount of
damage to it and prevents the
effects of fault from spreading
into the system.
For high voltage circuits relays
are employed to serve the
desired function of automatic
protective gear. The relays detect
the fault and supply the
information to the circuit breaker.
Relays used in control panel of the substation:
Overcurrent Relay
This type of relay works when
current in the circuit exceeds the
predetermined value. The
actuating source is the current in
the circuit supplied to the relay
from a current transformer. These
relay are used on A.C.
 Auxiliary Relay
 An auxiliary relay is used to
indicate the fault by glowing bulb
alert the employee.
 Tripping Relay
 This type of relay is in the
conjunction with main relay.
When main relay sense any fault
in the system, it immediately
operates the trip relay to
disconnect the faulty section
from the section.
CONCLUSION
The Uttar Pradesh Cooperation Limited has got radio
communication in microwave range in order to transmit and
receive data with various Substations in Uttar Pradesh to get
reliable transmission and distribution of electricity.
TRANSMISSION LINE

UPPTCL CHAKIA 132KV

  • 1.
    UTTAR PRADESH POWER TRANSMISSIONCARPORATION LIMITED ( U.P.P.T.C.L )
  • 3.
    INTRODUCTION The creation ofUttar Pradesh Power Corporation Ltd. (UPPCL) on January 14, 2000 is the result of power sector reforms and restructuring in UP (India) which is the focal point of the Power Sector, responsible for planning and managing the sector through its transmission, distribution and supply of electricity. UPPCL will be professionally managed utility supplying reliable and cost efficient electricity to every citizen of the state through highly motivated employees and state of art technologies, providing an economic return to our owners and maintaining leadership in the country.
  • 4.
    132KV Chakia Substation 132KV Chakia Substation is one important substation of UPPTCL. It is situated at Chakia Shahupuri in under LUCKNOW. The whole substation is divided in to two parts – 132 KV Switchyard & 33 KV Switchyard.
  • 5.
    The incoming linesfor Chakia 1.Shahupuri (132KV line) 2.Robartsganj (132KV line) The outgoing lines of Chakia 1.ilia Feeder 2.Kaudihar Canal 3.Chakia town 4.Chakia roller
  • 6.
  • 7.
    TRASFORMER Two transformer areused in 20MVA We know, MVA = 1.732VI For 20MVA (HV) For 20MVA (LV) 20*10^3=1.732*132*I 20*10^3=1.732*33*I I= 87.47A(HV) I=350A(LV)
  • 8.
    Lightning Arrester A lightningarrester is a device used on electrical power systems and telecommunications systems to protect the insulation and conductors of the system from the damaging effects of lightning.  The typical lightning arrester has a high- voltage terminal and a ground terminal. When a lightning surge travels along the power line to the arrester, the current from the surge is diverted through the arrestor, in most cases to earth.
  • 9.
    current transformer A currenttransformer (CT) is used for measurement of alternating electric currents. When current in a circuit is too high to apply directly to measuring instruments, a current transformer produces a reduced current accurately proportional to the current in the circuit, which can be conveniently connected to measuring and recording instruments. A current transformer isolates the measuring instruments from what may be very high voltage in the monitored circuit.
  • 10.
    Potential transformers Potential transformers(PT) (also called voltage transformers (VT)) are a parallel connected type of instrument transformer. They are designed to present negligible load to the supply being measured and have an accurate voltage ratio and phase relationship to enable accurate secondary connected metering. The PT is typically described by its voltage ratio from primary to secondary. Standard secondary voltage ratings are 120 volts and 70 volts, compatible with standard measuring instruments
  • 11.
    Circuit Breaker A circuitbreaker is an automatically operated electrical switch designed to protect an electrical circuit from damage caused by overload or short circuit. Its basic function is to detect a fault condition and interrupt current flow According to their arc quenching media the circuit breaker can be divided as- 1.Oil circuit breaker 2.Air circuit breaker 3.SF6 circuit breaker 4.Vacuum circuit breaker
  • 12.
  • 13.
  • 14.
  • 15.
  • 16.
    Isolators It is anoff-load device. It disconnects or isolates the circuit from the main power supply. Even though, isolators is a switch, it is not used as a normal on off switch. Isolators may provide additional safety features like, when switched off the trapped charge will be ground through a ground terminal in the isolator.
  • 17.
    CAPACITOR BANK The loadon the power system is varying being high during morning and low in evening which increases the load current. This result in the decreased power factor. The low power factor is mainly due to the fact most of the power loads are inductive and therefore take lagging currents. Capacitor bank accomplishes following operations: Supply reactive power Increases terminal voltage Improve power factor
  • 18.
    FUSE A fuse isa short piece of wire or thin strip which melts when excessive current through it for sufficient time. It is inserted in series with the circuit under normal operating conditions; the fuse element is at a nature below its melting point. Therefore it carries the normal load current overheating. It is worthwhile to note that a fuse performs both detection and interruption functions.
  • 19.
    BUS COUPLER The buscoupler consists of circuit breaker and isolator. Each generator and feeder may be connected to either main bus bar or spar bus bar with the help of bus coupler. Repairing, maintenance and testing of feeder circuit or other section. Bus coupler is a device which is used switch from one bus to the other without any interruption in power supply and without creating hazardous arcs. It is achieved with the help of circuit breaker and isolators.
  • 20.
    RELAY When a failureoccurs on any part of the system, it must be quickly detected and disconnected from the system. Rapid disconnection of faulted apparatus limits the amount of damage to it and prevents the effects of fault from spreading into the system. For high voltage circuits relays are employed to serve the desired function of automatic protective gear. The relays detect the fault and supply the information to the circuit breaker.
  • 21.
    Relays used incontrol panel of the substation: Overcurrent Relay This type of relay works when current in the circuit exceeds the predetermined value. The actuating source is the current in the circuit supplied to the relay from a current transformer. These relay are used on A.C.  Auxiliary Relay  An auxiliary relay is used to indicate the fault by glowing bulb alert the employee.
  • 22.
     Tripping Relay This type of relay is in the conjunction with main relay. When main relay sense any fault in the system, it immediately operates the trip relay to disconnect the faulty section from the section.
  • 23.
    CONCLUSION The Uttar PradeshCooperation Limited has got radio communication in microwave range in order to transmit and receive data with various Substations in Uttar Pradesh to get reliable transmission and distribution of electricity.
  • 24.