Video Surveillance Using Raspberry Pi Architecture

Video surveillance using raspberry Pi architecture
Publication History
Received: 17 September 2015
Accepted: 21 October 2015
Published: 11 November 2015
Citation
Ruturaj Shete, Mayuri Sabale. Video surveillance using raspberry Pi architecture. Discovery, 2015, 49(226), 37-43
Discovery ANALYSIS
The International Daily journal
ISSN 2278 – 5469 EISSN 2278 – 5450
© 2015 Discovery Publication. All Rights Reserved

VIDEO SURVEILLANCE USING RASPBERRY PI
ARCHITECTURE
Ruturaj Shete1
[1]
Electronics and Telecommunication Department,
Jayawantrao Sawant College of Engineering,
Savitribai Phule University of Pune,
Pune, Maharashtra, India-411028
Ruturajshete1008@outlook.com
Mayuri Sabale2
[1]
Electronics and Telecommunication Department,
Jayawantrao Sawant College of Engineering,
Savitribai Phule University of Pune,
Pune, Maharashtra, India-411028
mayurivsabale@gmail.com
Abstract-This project is about a remotely monitor surveillance
area using Raspberry Pi architecture. Raspberry Pi B+ model is a
credit card sized single board computers developed in the UK by the
Raspberry Pi Foundation, which provides all the basic features of a
computer. Its core architecture is built from ARM11 (Broadcom
BCM2835 SoC). This project deals with Raspberry Pi processor,
stepper motor, webcam, PIR sensors and GSM module. Raspberry
Pi which is heart of system collects surveillance data through
interfaces like webcam, PIR sensors. The video stream is locally as
well as remotely visualized. Role of a stepper motor is 3600
surveillance. Further, SIM900A module is used to interface
GSM/GPRS functionality with Raspberry Pi processor. The alert
notification is sent to user, when Raspberry Pi detects living body or
motion of living body in surveillance area. Raspberry Pi transmits
the real-time video through internet as well as it sends notification
message to the user though GSM module. The Raspberry Pi having
these all interfaces using communication ports like GPIO, Ethernet
and USB.
Keywords- Raspberry Pi, GSM module, Stepper motor,
webcam,PIR sensors, GPIO, Ethernet and USB.
I. INTRODUCTION
An automated wireless Video surveillance solution using
Raspberry PI is proposed in this project. The proposed solution
can be applied in to the border surveillance and various security
systems. A wireless video surveillance system basically consists
of three processing blocks
 The video capture and processing.
 The video compression and transmission in wireless
networks.
 Surveillance area monitoring and controlling from
remote location.
Live video streaming refers to sending video signals real time
over the Internet. Stream video can be clearly visualized on
webpage due to Raspberry Pi, which is having picture quality
configurations. Also Video Surveillance over wireless sensor
networks has been widely adopted in various cyber-physical
systems including border security, traffic analysis, healthcare
systems in hospitals, public safety (bus, mall etc.), wildlife
tracking and environment/weather monitoring etc.
II. BLOCK DIAGRAM
Fig. 1. Block diagram of proposed system
Fig. 1 shows the block diagram of video surveillance using
Raspberry Pi architecture. System consists of Raspberry Pi, PIR
sensors, GSM module, stepper motor, LCD display, alarm and
webcam. Raspberry Pi board is used for video processing and
sending the data to the authentic person over the internet. With
the help of processor we will make all the data compatible to
send over the wireless medium that is internet. RS232
(MAX232) is used to communication between the Raspberry Pi
(ARM11 Processor) and GSM module. GSM module is used to
send the notification through GSM/GPRS standards. Webcam is
mounted on stepper motor; webcam is having the role of video or
image capturing. Because of stepper motor surveillance in all

direction is possible. Also motor driving circuit is used for motor
operation. Need of PIR sensors are for motion detection in
surveillance area. LCD display and alarm is used to give
surveillance notification locally. Because of wireless medium we
can send the data anytime anywhere.
Fig. 2. System Design
Fig. 2 shows, the system design of whole project. The
webpage is accessed by calling IP address of Raspberry Pi
processor. The authentic person can only access the data only,
because we provided the security through the username and
password to access the webpage. HTML webpage can open at
any device which is having the internet connection to it. The
operating system is not obstacle in this case, because HTML
webpage is supported by all most all operating systems.
III. FUNCTIONAL DESCRIPTION
The functions of various components are as mentioned
below:
A.Raspberry Pi: Raspberry Pi B+ module is capable of
performing various basic functionalities of multimedia, gaming
and surveillance applications. The functionality of various
components of Raspberry Pi is stated as below:
Fig. 3. Block Diagram of Raspberry Pi B+ Module
1)Micro SD socket: SDIO (Secured Digital Input/Output)
memory card is required to store the operating system and files.
The operating system boots from Micro SD card, it is running a
version of the Linux operating system (i.e. Raspbian OS). The
maximum support of the SD card is about 32GB.
2)Micro USB Power supply socket: Raspberry Pi Micro USB
socket 5V, 2A. It also creates three different voltages 3.3V, 2.5V
and 1.8V for the processor and Ethernet.
3)Ethernet socket: 10/100 BaseT Ethernet socketused for
LAN network.
4)Audio output: 4-pole (TRRS) type connector, 3.5mm Jack,
HDMI (High Definition Multimedia Interface), stereo audio and
composite video.
5)Video output: HDMI (rev 1.3 & 1.4), composite RCA (PAL
and NTSC). It is type of electrical connector commonly used to
carry audio and video signals.
6)USB socket: Four Universal Serial Hub 2.0 connectors are
available. The LAN9512, which isbasically, turned the 1 USB
port on the processor into 2 ports + Ethernet.
7)GPIO Connector: 40-pin 2.54mm (100mil) expansion
header: 2x20 strip providing 27 GPIO pins as well as +3.3V,
+5V and GND supply lines.
8)Broadcom BCM2835 SoC: 700MHz low power ARM
1176ZFS application processor is available on board.
9)Graphic Processing Unit: Dual core VideoCore IVR
Multimedia Co-processor is used, which is having 1080p30
H.264 high profile decode.
10) Power requirements for board are 5V, 2A.
Fig. 4. Raspberry PI B+ module
Raspberry Pi is having the role of video compression.
Webcam is having 1080p high definition video/image output.
According to need we can compress the video to transmit
over the wireless media. We compressed the video in 320x240
resolution and 15 frames per second by configuring Raspberry Pi
module. This resolution and frame rate is selected because of
smoothly transmission of data and clearly visualize on webpage.
B.USB camera: Webcam is used to capture the video and
images of surveillance area. Here, we use Zebion USB webcam.

Webcam having the specifications like 10MP and 1080p
maximum resolution.
C.Stepper motor: It is used to track whole 3600
surveillance.
Because of this camera will rotate in 3600
. Webcam is mounted
on right the top of the motor. Here, we required 2kgtorque DC
stepping motor. Its power consumption is 12V, 0.5A.
In this project, we used stepper motor rotations in two
modes:
1) Normal mode- In this mode, stepper motor is in steady
position, it will not change its angle until it will not getting any
command from user. On webpage two options are available to
rotate motor either in clockwise direction or in anticlockwise
direction. When you single click on the button motor will change
its angle by 450
.
2) Sense mode- In sense mode, when any of the PIR sensors
detect the motion, stepper motor will change its angle by 900
towards that PIR. When PIR1 detects the motion stepper motor
will change its angle by 900
towards PIR1.
D)PIR sensor: PIR (Pyroelectric Passive Infrared) used for
the purpose of detection of motion; if any movement occurred in
surveillance area it will send the data to processor. Raspberry Pi
will process on it and send the notification through GSM module,
as well as processor will display on LCD display that which
sensor detects the motion in that area of surveillance. According
processor will take action and camera automatically rotate
towards that detected area.
In this project, we used the DYP-ME003 PIR Motion Sensor
Module, which is based on BIS S0001IC. BIS S001 is a micro
power PIR motion detector IC.
Fig. 5. Working principle of PIR sensor
PIRs are basically made of a pyroelectric sensor, which can
detect levels of infrared radiation. Everything emits some low
level radiation, and the hotter something is, the more radiation is
emitted. The sensor in a motion detector is actually split in two
halves. The reason for this is we are looking to detect motion
(change) not average IR levels. The two halves are wired up so
that they cancel each other out. If one half sees more or less IR
radiation than the other, the output will swing high or low.
E.GSM module: This model is purposely used to notify the
motion is detected in the surveillance area. When PIR will detect
the motion GSM will send the notification message to the
authentic person. SIM900A GSM modem is used for this
purpose. This modem is works on 900/1800 MHz frequency. The
modem is having the RS232chip, which will allows you to
connect Raspberry PI processor using MAX232. The baud rate is
configurable from 9600 to 115200 using AT commands.
F.LCD Display and alarm: In this project, 16X2 LCD display
is used to indicate the sensors output. It will show out of two
sensors which sensor detected the motion. Alarm is used locally
getting the notification that motion is detected.
IV. FLOW CHART
Fig. 6. Flow chart of complete process of project
Fig. 4.1 shows, the total process of project works
sequentially. There are basically two modes when PIR detect the
motion and another when PIR will be in passive mode, based on
that the next procedure will be depending.

V. Raspberry Pi Initial Setup
A. Installation of operating system: To get started with
Raspberry Pi you need an operating system. NOOBS (New Out
Of the Box Software) is an easy operating system install manager
for the Raspberry Pi.
The following Operating Systems are currently included in
NOOBS:
 Raspbian,
 Pidora,
 OpenELEC,
 RaspBMC,
 RISC OS,
 Arch Linux.
Steps to install NOOBS:
1) NOOBS is available for free download on the Raspberry Pi
website: raspberrypi.org/downloads.
2) Then download [14] and install the SD card formatter
software into windows operating system laptop to make the SD
card compatible for installing NOOBS.
3) Insert the memory card into memory card slot of laptop,
then format the SD card using this software in FAT format.
4) Then download [15]and install Win32diskimager software,
this is a Windows program for saving and restoring images from
removable drives (USB drives, SD Memory cards, etc.). It can be
used to write boot images to a SD Flash device or USB flash
device, making it bootable, which is available at:
5) Using this tool, extract the downloaded image into micro
SD card. Now, micro SD card is ready to use in Raspberry Pi.
6) But this operating system is not compatible with the new
B+ model so using putty, we have to upgrade and update this OS.
7) Now download [17] and install the putty software on to the
windows platform. Putty is a free and open-source terminal
emulator; serial console and network file transfer application. It
supports protocols, including SCP, SSH, Telnet, rlogin, and raw
socket connection. Using this tool we can configure and setting
up the Raspberry Pi easily.
8) Using this tool, we have to upgrade and update the
operating system to make compatible with Raspberry Pi B+
model. For that reason two commands are necessary;
1)sudo apt-get update;
2)sudo apt-get upgrade;
9) Using your laptop internet sharing facility you can do this
upgrade and update operating system of Raspberry Pi.
10) To use NOOBS on windows platform we have use
TightVNC software. TightVNC [16] is a cross-platform free and
open-source remote desktop software application that uses and
extends the RFB protocol of Virtual Network Computing (VNC)
to control another computer’s screen remotely [11]. So download
and install this software, which is available at:
Fig. 7. Putty configuration settings
11) You have to give a command in putty to open TightVNC
server,“sudo tightvncserver”, after this command it will show
NOOBS in windows platform.
Fig. 8. TightVNC command given in Putty
12) Further interface programming is done through the Genny
software which is built in function in Raspbian operating system.
LX terminal is use as command prompt in Raspbian OS.
VI. RESULTS
We successfully configured Raspbian operating system,
which is freely available. Configuration of static IP for Raspbian

operating system is done through putty software. So this static IP
facilitates remote access.
Webcam can rotate from webpage in two directions that is in
clockwise and in anticlockwise direction. When single click is
done on direction the camera angle will change by 450
, so after 6
click it will complete whole 3600
rotation.
Fig. 6.1: Webpage at the receiver section
The actual project wired connection is shown in fig. 6.2,
Raspberry Pi having enough capability for high definition video
and image processing and transmission. So, Raspberry Pi
interfaces with the GSM module, PIR sensor, stepper motor and
webcam in this project.
Fig. 6.2: Project Overview
Fig. 6.3: LCD Display showing which sensors detects motion
VII. ADVANTAGES
A. Very small space required as compared to existing
available surveillance systems in market;
B. Cost efficient than other surveillance systems;
C. Wireless transmission, so there is minimum data loss or
minimum data delay;
D. Whole around 360 degree surveillance area will be under
surveillance because of our system;
E. There no any of any fixed surveillance Centre or room, we
can observe it from anywhere at any time;
F. It can work on battery power supply, because very less
power consumption, only two to three watt power supply will be
sufficient.
VIII. APPLICATIONS
A. In hospital for patient surveillance;
B. In city buses or in Wi-Fi enabled trains to reduce the
crime;
C. In any big housing apartments, in big organizations or in
big institutes;
D. In the companies where surveillance is needed,
E. Also on the international borders for the surveillance
purpose.
IX. CONCLUSION AND FUTURE SCOPE
Thus we have designed a smart, compact, cost effective
surveillance system capable of capturing video/image and
transmit over the internet. It is most important to have reliability
privacy and security on both ends, which is achieved in this
project. It is provided authentication at the receiver side, hence it
can access by the concern person only. Also some addition

options like camera angle control, to view in 3600
. If necessary
changes will be done in future, so that it can be also use in drone,
international boarder surveillance system or any other military
applications. Using digital image processing in this we can
develop this same system for various applications.
ACKNOWLEDGMENT
This work is internally supported by our project guide
Prof.T.S.Mote; also our project coordinator
Prof.M.B.Tadwalkar;our head of the department
Prof.V.M.Sardar; our principle Dr.M.G.Jadhav and also our
campus director Dr.V.A.Bugdefor supported us to do real time
surveillance system that is very useful for the society. I like to
express my gratitude towards my father and family. My thanks
also go to my colleague in developing the project and people who
have willingly helped me out.
References
[1] Dr. Shantanu K. Dixit, Mr. S. B. Dhayagonde, “Design and Implementation
of e-surveillance Robot for Video Monitoring and Living Body Detection”
in IJSRP, vol. 4, issue 4, April 2014.
[2] Priyanga .M, Raja Ramanan .V, “Unmanned Aerial Vehicle for Video
Surveillance Using Raspberry Pi” in IJIRSET, vol. 3, special issue 3, pp.
1715-1720, March 2014 [ICIET’14, India].
[3] Mrs. P. Suvitha Vani, Miss. Nithyappriya .G, “Establishing SSH connection
and Interfacing GSM/GPRS functionality with Raspberry Pi” in IJIRCCE,
vol. 2, special issue 1, pp. 1497-1501, March 2014 [Proceeding of
ICGICT’14, India].
[4] Sanjana Prasad, P. Mahalakshmi, A.John Clement Sunder, R. Swathi,
“Smart Surveillance Monitoring System Using Raspberry PI and PIR
sensor” in IJCSIT, vol.5(6), pp.7107-7109, 2014.
[5] DhavalChheda, DivyeshDarde, Shraddha Chitalia, “Smart Projectors using
Remote Controlled Raspberry Pi” in International Journal of Computer
Applications, vol. 82- no. 16, Nov. 2013.
[6] Gu, Yi, et al. "Design and Implementation of UPnP-Based
SurveillanceCamera System for Home Security." Information Science and
Applications (ICISA), 2013 International Conference on. IEEE, 2013.
[7] MdAthiq UR Raza Ahamed M., WajidAhamed, “A Domestic Robot for
Security Systems by Video Surveillance Using Zigbee Technology”,
International Journal of Scientific Engineering and Technology (ISSN:
2277-1581) Volume 2 Issue 5, pp: 448-453, 1 May 2013.
[8] Mitchell, Gareth. "The Raspberry Pi single-board computer will
revolutionize computer science teaching for & Against Engineering &
Technology”, 7. 3 2012,pp: 26-26.
[9] N. Luo, “A wireless traffic surveillance system using video analytics”, M.S.
thesis, Dept. Comput. Sci. Eng., Univ. North Texas, Denton, TX, USA,
2011.
[10] Information on the New Out Of the Box Software (NOOBS):
www.raspberrypi.org/archives/4100: This is the official website of the
Raspberry Pi project.
[11] http://cplus.about.com/od/raspberrypi/a/How-Do-I-Setup-Ssh-On-
Raspberry-Pi.htm
[12] www.raspberrypi.org
[13] http://blog.miguelgrinberg.com/post/stream-video-from- the-raspberry-pi-
camera-to-web-browsers-even-on-ios-and-android
[14] https://www.sdcard.org/downloads/formatter_4/
[15] http://sourceforge.net/projects/win32diskimager/files/latest/download
[16] http://www.tightvnc.com/download.php
[17] http://www.chiark.greenend.org.uk/~sgtatham/putty/download.html

Video Surveillance Using Raspberry Pi Architecture

More Related Content

What's hot (20)

Similar to Video Surveillance Using Raspberry Pi Architecture (20)

Video Surveillance Using Raspberry Pi Architecture