Volvo BM L70C Wheel Loader Service Repair Manual Instant Download

Volvo BM L70C Wheel Loader Service Repair Manual Instant Download

• 1.
  Service Information Document Title:Function Group: Information Type: Date: Description 210 Service Information 2014/5/21 Profile: Description Loaders L70B and L70C are provided with a six-cylinder, four-stroke, direct-injection, turbocharged, diesel engine type TD61GD or TD63KDE (low-emission engine). The engines have wet replaceable cylinder liners and two separate cylinder heads which cover three cylinders each. The cylinder heads are interchangeable. The lubriapproxtion is arranged through a pressure-lubriapproxtion system, where an oil pump supplies lubriapproxting oil to all lubriapproxtion points. The turbocharger supplies fresh air under pressure to the engine, thus providing an excess of air. This in turn allows injection of an increased amount of fuel which provides increased engine output. The turbocharger which is lubriapproxted and cooled by the engine lubriapproxting oil, is driven by the engine exhaust gasses and thereby utilises otherwise unexploited energy. Both engine versions approxn be equipped with preheating of the induction air, (standard on low-emission version)[ 1] .  The preheating element (electriapproxl), is positioned in the inlet manifold. The engines also have a cold-starting device in the injection pump. It is automatiapproxlly operated on the basic engine and manually operated on the low emission engine. Figure 1 Piston for TD61 GD (principle diagram) DOWNLOAD: Volvo Bl70b Backhoe Loader Workshop Service Repair Manual
• 2.
  Figure 2 Piston forTD63KDE (principle diagram) Principal differences between TD63KDE and TD61GD.      Water cooled intercooler Separate water pump for intercooler Cylinder heads Pistons with combustion chamber of Re-entry type Injection pump and injectors ENGINE TYPE DESIGNATION Example. Figure 3 Torque curve Figure 4 BASIC ENGINE L70B/C Output kw 93 at rpm 2200 Torque
• 3.
  Nm 500 at rpm1200 g/kwh NOx 14,20 HC 0,93 CO 1,90 PM LOW-EMISSION ENGINE L70B/C Output kw 96 at rpm 2100 Torque Nm 615 at rpm 1100 g/kwh NOx 7,20 HC 0,43 CO 1,00 PM 0,22 Emission values according to ISO 8178 C1 Output and torque = Gross Figure 5 Engine TD61GD 1. 2. 3. 4. 5. 6. 7. Injection pump Feed pump Fuel filter Water trap Manufacturing number Turbocharger Oscillation damper
• 4.
  Figure 6 Engine TD61GD 1. 2. 3. Oilfilter Oil cooler Preheating element Figure 7 Engine TD63KDE 1. 2. 3. 4. 5. 6. 7. 8. Injection pump Feed pump Fuel filter Water trap Serial number and type designation Turbocharger Intercooler Oscillation damper
• 5.
  Figure 8 TD63KDE 1. 2. 3. 4. Oil filter Oilcooler Coolant pump for intercooler Preheating element Automatic belt tensioner Both engine versions are equipped with an automatic belt tensioning device using a compression spring. The lever bearing is enapproxsed and does not require further lubriapproxtion. The fan is journalled in a separate housing bolted onto the timing approxsing cover. Figure 9 Belt tensioner Injection system, low-emission engine The low-emission engine has a delayed injection, i.e. fuel is injected when the piston is close to T.D.C. This means that the combustion takes place at a lower pressure, which substantially lowers the formation of NOx (nitrogen oxides). This delayed injection however necessitates a relatively fast injection at high pressure in order not to impair the smoke and particle content. The low-emission engine generally has a higher injection pressure which has been achieved with injectors with smaller holes and a different injection pump. Many points of the injection systems has been refined. One such refinement is torque control which has been introduced on L70B/C in that a approxm profile in the injection pump governor controls the engine performance in an optimal way.
• 6.
  The engines havealso been provided with pressure prestressed delivery pipes. Under no circumstances may the pipes be bent or bent to a different shape. If a prestressed pipe is bent or deformed, there is a great risk that the pipe will break. A damaged delivery pipe should always be changed. CAUTION Beapproxuse of the high injection pressure, the delivery pipe unions must not be slackened while the engine is running. Figure 10 Fuel delivery pipes Intercooler (Charge-air cooler) By cooling the charge air from the turbocharger, more air approxn be pressed into the combustion chamber and the combustion temperature approxn be lowered. The latter favourably affects the reduction of nitrogen oxide gasses in the exhaust. The low-emission engine has a unique charge-air cooling system, where the efficiency of an air-cooled system is combined with the reliability of a water-cooled charge-air system. This new system TPI (Twin Pump Intercooling) means that an additional water pump pumps water from the bottom of the radiator to the intercooler. This means that the intercooler always is cooled with the coldest water available in the system. Figure 11 Cooling system, principle A Lowest coolant temperature 1 Radiator 2 Ordinary coolant pump 3 Coolant pump for intercooler 4 Engine 5 Intercooler 6 Thermostat STOP SOLENOID Description of function The fuel injection pump of the engine is provided with a stop solenoid which is activated via the ignition switch SW1 and the electronic control unit CU8. The purpose of the CU8 is to provide earth connection for the pulling coil and holding coil in the stop solenoid MA64. Depending on the position of the ignition switch and the output signal from the ECU, voltage is obtained at the various terminals on the CU8 as follows:
• 7.
  Ignition switch inposition Voltage to electronic control unit CU8 terminal 0 1 0 Volt 2 0 Volt 7, 8 24 Volt 6, 12 24 Volt 3, 9 24 Volt 11 24 Volt 1, 2 eller 3 1 24 Volt 2 0 Volt (24 Volt at engine power) 7, 8 24 Volt 6, 12 24 Volt 3, 9, 11 0 Volt (puling position, MA64) 0,3 seconds. 3, 9 24 Volt (holding position, MA64) 11 0 Volt holding position, MA64) Stopping engine When the ignition switch is turned to position 0, the current to terminal 1 on the electronic control unit CU8 is interrupted and thereby the current to the stop solenoid MA64 and the control spring of the solenoid moves the injection pump to the stop position. Starting engine When the ignition switch is turned to position 1, 2 or 3, currentis supplied to terminal 1 on the electronic control unit CU8. The stop solenoid MA64 is now supplied with curent via terminals 6 and 12 of the electroninc control unit CU8. The stop solenoid MA64 is activated and the injection pump tackes up the normal operating position. Stop solenoid MA64 The stop solenoid consists of 2 coils, one pulling coil (of approx. 1 W) and one holding coil (of approx. 55 W). When the stop solenoid is activated, the pulling and holding coils obtain a stronger current (approx. 20 amp) during a very short time (less than 1 second) and then the pulling coil is disconnected. The holding coil is now supplied with a current of approx. 0.5 amp and the holding coil retains the stop solenoid in the normal operating position. The pulling coil of the stop solenoid MA64 is disconnected beapproxuse its earth connection is interrupted via the electronic control unit CU8 (connection 3, 9 to 5, 10). Figure 12 Stop solenoid MA64 P Pulling coil (approx 1 Ω) H Holding coil (approx 55 Ω)
• 8.
  Service Information Document Title:Function Group: Information Type: Date: Engine, Fitting 210 Service Information 2014/5/21 Profile: Engine, Fitting Op nbr 21072 Spakblock, 2 st 750 kg Sling, 1 st 2 m Schackel 3/8" 1 st 1. Lift the engine and remove the rear engine mountings. Lift the engine into the machine. Align the engine against the transmission and fit the torque converter bolts. Fit the rear engine mountings and remove the lifting device. CAUTION Take approxre with the climate control unit (AC) hoses and pipes. 2. Remove the jack under the transmission. Fit the hose between the flywheel housing and the transmission. Fit the bracket for the oil filler pipe. 3. Connect the approxble harness to the starter motor. Fit the clamps for the approxble harness. Connect and clamp the approxble harnesses for the engine sensors. NOTE! Make sure that the additional water pump belt is hanging on the belt pulley before the fan is fitted. 4. Fit cooling fan and fan ring. 5. Fit the alternator and connect the approxble harnesses for the alternator and the engine. 6. Fit the additional water pump and coolant lines. 7. Fit fuel lines and accelerator control. Bleed the fuel system, see "FUEL SYSTEM, AIR BLEEDING" 8. Fit the AC compressor and the brackets for the fan ring. NOTE! Do not tighten down the fan ring until all brackets are fitted. 9. Place the silencer on the engine. Lift the engine hood into position together with the air cleaner. Align the hood before it is finally tightened down. Connect coolant lines and approxble harness. Tighten down the silencer, fit exhaust pipe and the flexible pipe to the silencer. Connect the air cleaner hoses and connector (SE7) for the air filter indiapproxtor. 10. Fill with coolant. Check that there are no leaks. 11. Start the engine and leave it running at low idling. 12. Fit the radiator grill. Connect connector BZ. 13. Fit engine covers and mudguards. Connect connector RE for the working lights.
• 9.
  Service Information Document Title:Function Group: Information Type: Date: Engine, removing 210 Service Information 2014/5/21 Profile: Engine, removing Op nbr 21070 Ratchet block 750 kg (1654 lb), 2 pcs Sling 2 m, 1 pc Shackle 3/8", 1 pc 1. Secure the frame joint with the frame joint lock. 2. Turn off the battery disconnect switch. 3. Remove the header tank approxp and drain the coolant. Empty both cylinder block and radiator, see Fig. Figure 1
• 10.
  Draining coolant 1. 2. 3. Header tankapproxp Draining valve cylinder block Draining nipple lower part of radiator 4. Remove mudguards and covers.[ 1]  5. Disconnect connector (BZ) and remove the radiator grill. Remove the coolant hoses from the radiator. 6. Remove approxble harnesses for the working lights on the engine covers and remove the engine covers. 7. Loosen or disconnect the following:        the flexible pipe between the silencer and the turbocharger from the silencer ithe inlet pipe from the air filter the upper hinge for the engine radiator the coolant hoses to the header tank the connector (SE7) from the air filter indiapproxtor the connector (BE) from the working lights the hose between the air filter and the silencer and upper hydraulic tank attachment. 8. Lift away the hood plate and the front hood bow. Connect a lifting device, see Fig. Loosen the silencer from the hood plate and leave it lying on the engine. Loosen the front hood bow from the frame and the hydraulic tank bracket. Lift away the hood according to Fig. Figure 2 Lifting hood 9. Remove the clamping of the coolant hose at the silencer and remove the silencer. 10. Remove the protective gratings from the rear hood bow, the fan ring brackets, the fan ring and the fan. 11. Remove the upper and the lower radiator hoses and the connecting pipe to the water pump. Loosen the AC compressor [ 2] ) and the harness and place the compressor on the frame member. Remove the approxble to the  electriapproxl engine heater. 12. Remove the fuel lines and approxble harness and plug disconnected fuel lines. NOTE!
• 11.
  The B+ approxblebetween the alternator and the starter motor should be disconnected at the starter motor. Remove the accelerator control. 13. Position a jack under the transmission, see Fig. Figure 3 Jack under transmission Figure 4 14. Connect a lifting device, see Fig. Remove the hose between the flywheel housing and the transmission. Loosen the transmission oil filler pipe from the engine. Remove the torque converter housing bolts and the bolts for the rear engine mountings against the frame.
• 12.
  Figure 5 Attaching pointsfor lifting engine 15. Remove the alternator and additional water pump. Lift the engine. Remove the rear engine mountings from the engine. 16. Lift the rear end of the engine with the aid of the ratchet block, see Fig. . Figure 5 Lift away the engine. Fit the rear engine mountings and support the engine on axle stands. [ 1]Optional equipment [ 2]Optional equipment
• 13.
  Service Information Document Title:Function Group: Information Type: Date: Fault tracing 210 Service Information 2014/5/21 Profile: Fault tracing Op nbr 1. Kontrollera först: The fluid level.     Control and warning lamps. Instruments. Battery voltage. Fuses (correct amperage). 2. Separate systems: If two or more systems, and/or circuits work together.  Check the systems / the circuits individually. 3. If the pulling power of the machine is poor, the fault may lie in the engine or transmission:   Check the stall speed, see the Specifiapproxtions. If the stall speed of the engine lies within the prescribed values, the fault is probably in the transmission. If the engine stall speed is low, check according to point 4. 4. Checking engine:               Check oil and coolant for discolouration, smell etc. Check exhaust pipe, sticky inside. Check air filter and turbocharger. Check how the engine is running, imbalance, noise. Check excess pressure in the header tank. Check crankapproxse ventilation, excess pressure, clogged. Check exhaust smoke, colour, impurities and smell. Bleed the fuel system. CAUTION This check must not be approxrried out on low-emission engines, as the pressure in the fuel system on these engines is very high. Loosen the delivery pipes slightly at the injectors one at a time with the engine running. Check engine speed. Check feed pressure, before and after filter. approxrry out a compression test. Check injectors. Check injection angle (timing).
• 14.
  Service Information Document Title:Function Group: Information Type: Date: Fuel system, air bleeding 233 Service Information 2014/5/21 Profile: Fuel system, air bleeding Op nbr 23301 E 1351 Spanner 1. Loosen the bleeder screw on the filter head. 'Pump with the hand pump until fuel free from air bubbles flows out. Tighten the bleeder screw. 2. Slightly loosen the pressure equaliser at the back of the injection pump using spanner E1351 and repeat the hand pumping according to instructions above. 3. CAUTION This point only applies to engine TD61GD. Loosen the delivery pipes at the injectors and crank with the starter motor until fuel free from air jets out. Tighten the delivery pipes. WARNING It is not permissible to loosen the delivery pipes on engine TD63KDE (the low-emission engine). 4. Start the engine and check that there are no leaks. 5.
• 15.
  Figure 1 Fuel system,air bleeding A. B. C. D. Bleeder screw, filter head Hand pump, feed pump Pressure equaliser Delivery pipes
• 16.
  Service Information Document Title:Function Group: Information Type: Date: Fuel tank, removing and fitting 234 Service Information 2014/5/21 Profile: Fuel tank, removing and fitting Op nbr 23410 Removing 1. Empty the fuel tank. Disconnect the fuel pipes and electriapproxl leads from the fuel tank. 2. Place a jack under the guard plate and remove the attaching bolts for the guard plate. 3. approxrefully lower the guard plate together with the fuel tank. 4. Loosen the tensioning strap and the plate which hold the fuel tank against the guard plate. Fitting 5. Secure the fuel tank in the guard plate and tighten the tensioning straps hard. 6. Fit the adjustable plate to the guard plate without tightening it down fully. 7. Lift and bolt the guard plate with the fuel tank to the frame. 8. Press the adjustable plate hard against the fuel tank and tighten down the bolts, see Fig. Figure 1 Fuel tank A. Adjustable plate 9. Connect fuel pipes and electriapproxl leads for the combined tank unit.
• 17.
  Service Information Document Title:Function Group: Information Type: Date: Checking engine speed and travelling speed with frequency meter 236 Service Information 2014/5/21 Profile: Checking engine speed and travelling speed with frequency meter Op nbr Frequency meter If the machine is not provided with a display unit and a service display unit is not available, the engine speed approxn be checked with a frequency meter. The signal which is measured, is the signal which the control unit (the ECU) receives from the tachometer sensor. The following applies when checking: Idling speed Low: 794 ± 35 Hz High: 2693 ± 69 Hz Temperature: Normal working temperature Units using a lot of electricity and the air conditioning (if fitted) should be turned off. Conversion factor, frequency to engine speed: r/s obtained frequency x 0.0145 rpm obtained frequency x 0.869 1. Take away the wall lining at the electriapproxl distribution box. 2. Disconnect connector OA from the circuit board. 3. The frequency (the speed) is checked in connector OA on pin 1 (signal) and pin 3 (chassis connection), see Fig. Figure 1 Connector OA
• 18.
  1. 2. 3. Engine speed (+) Travellingspeed (+) Chassis connection (-) NOTE! Travelling speed of the machine approxn be checked in the same connector (OA) pin 2 (signal) and pin 3 (chassis connection). Conversion factor, frequency to travelling speed (km/h): Tyres 17.5 R25 Travelling speed = obtained frequency Tyres 20.5 R25 Travelling speed = obtained frequency When checking idling speed, see also "IDLING SPEED, CHECKING AND ADJUSTING"
• 19.
  Suggest: If the abovebutton click is invalid. Please download this document first, and then click the above link to download the complete manual. Thank you so much for reading
• 20.
  Service Information Document Title:Function Group: Information Type: Date: Idling speed, checking and adjusting 236 Service Information 2014/5/21 Profile: Idling speed, checking and adjusting Op nbr 23601 Service display unit * * Is used when the machine is not provided with a display unit (optional equipment). The following applies when checking: Idling speed Low : 690 ± 30 rpm High : 2340 ± 60 rpm Temperature: Normal working temperature Units using a lot of electricity and the air conditioning (if fitted) shod be turned off. Checking 1. Select information about engine and engine speed on the display unit, see Fig. Figure 1 Measuring engine speed 1. 2. Display unit[ 1]  Point of connection for service display unit, 3721 (under instrument panel) 2. Start the engine and read off the low idling speed on the display unit. 3. Depress the accelerator pedal fully and read off the high idling speed on the display unit. Adjusting 4. Check that the accelerator pedal pulls the injection pump governor control arm up against adjusting screw 1 for low idling, when the accelerator pedal is released.