Pile Foundations
293 likes231,988 views
The document provides an overview of pile foundations, focusing on onshore types and serving as a beginner's guide. It covers various aspects including installation methods, load capacity calculations, and testing procedures for different types of piles, with an emphasis on simplifying complex concepts and methodologies. Additionally, it discusses the negative effects of soil conditions on pile performance and the importance of safety factors in determining the ultimate capacities of foundational systems.
Pile Foundations
- 1. PILE FOUNDATIONS By Varanasi Rama Rao ( Engineer- Civil & Structural ) 04/03/2009
- 2. Preface Pile foundations is a very vast subject and it is not possible to cover all the information regarding pile foundations in one book or presentation. The objective of this presentation is to give an overall view of the subject which will serve as beginners guide. The focus of the presentation is mainly on onshore pile foundations. The author has tried to explain the subject through simple concepts and visuals without giving detailed methodologies or mathematical concepts to maintain the interest of the beginner ,without loading his mind with unnecessary confusion . However, some formulae were presented at some places only to appreciate the statements made. The author assumes that the reader has basic knowledge of soil mechanics and foundation engineering and basic principles of engineering. The author will be pleased to accept comments and suggestions, without deviating from the basic objective of the presentation, for further improvement. Varanasi Rama Rao 04/03/2009
- 3. Contents 3. Pile installation 1. General Installation of Driven piles Overview Installation of Bored piles Pile capacities Advantages and Disadvantages of various Pile groups piles Settlement Analysis Design Steps 4. Miscellaneous 2. Special Topics Pile driving formulae Pile cap configurations Negative skin friction Structural Design of Pile Socketed piles and Pile cap Dynamic pile testing Flow chart for Pile selection Pile integrity testing Real time pictures of Piles Dynamic loading on piles 04/03/2009 5. References
- 5. Overview Pile foundations are adopted generally in the following situations: •Low Bearing Capacity of soil . •Non availability of proper bearing stratum at shallow depths. •Heavy loads from the super structure for which shallow foundation may not be economical or feasible. 04/03/2009
- 6. Classification of Piles Based on material • Concrete • Steel • Timber Based on method of construction/installation. • Driven /Displacement Pre cast Piles • Driven/Displacement Cast in Situ Piles • Bored/ Replacement Pre cast piles • Bored/ Replacement Cast in situ piles. Based on Load transfer mechanism • End bearing piles • Friction/Floating piles • Bearing cum Friction piles 04/03/2009
- 7. Based on sectional area • Circular • Square • H • Octagonal • Tubular Based on Size • Micro piles dia. < 150 mm • Small dia. pile dia. >150mm and <600 mm • Large dia. piles > 600 mm Based on inclination • Vertical Piles • Inclined/ raker Piles 04/03/2009
- 8. How does a pile look like? • Before presenting the actual picture of a pile foundation some schematic pictures of pile foundation are presented below. 04/03/2009
- 9. Figure 1 All the above schematics show the various types of pile foundations and loads carried by them 04/03/2009
- 10. Schematics of Pile foundations based on method of construction 04/03/2009 Figure 2
- 11. What are the loads coming on to the pile foundation? All the loads from super structure viz. Dead loads, Live loads Wind loads and Seismic loads. The loads from the surrounding soil in case of seismic event. Water loads in the case of off- shore structures 04/03/2009
- 12. Typical loading diagram on a single pile embedded in soil V M H Soil layer 1 Soil layer 2 Soil layer 3 Figure 3 Note: V can be either downward or upward depending on the pile is subjected to compressive or tensile load 04/03/2009
- 13. Piles usually exist as groups which are all integrated by means of a pile cap as shown in the below schematic 04/03/2009 Figure 4
- 14. What are the load carrying mechanisms of piles? • End bearing cum friction piles carry vertical compressive loads partly by means of resistance offered by the hard stratum at the tip of the pile and partly by the friction developed between the pile shaft and soil • Pure friction piles carry the major part of loads only by means of friction developed between pile shaft and soil; and pure End bearing piles only by means of bearing resistance at the tip of the pile • In both the above cases lateral loads are carried by the lateral resistance offered by the surrounding soil. 04/03/2009
- 15. SCHEMATICS SHOWING AXIAL LOAD CARRYING MECHANISM 04/03/2009 Figure 5
- 16. 04/03/2009 Figure 6
- 17. Load carrying mechanism of pile subjected to Lateral Loading and Moment Y X 04/03/2009 Figure 7
- 18. Load carrying mechanism of pile Subjected to tension/pullout Pile in tension Only friction and weight of pile will 04/03/2009 Figure 8 resist tension.
- 19. What is meant by load carrying capacity of the pile foundation? Load carrying capacity of the pile in the context of foundation engineering: The amount of load the pile can carry without undergoing continuous displacements for insignificant load increments by virtue of its boundary condition (soil condition) and not by virtue of its structural strength. the assumption for this definition is – the failure of surrounding soil occurs prior to the failure of the pile material especially in the case of concrete piles 04/03/2009
- 20. Pile Capacities What are the various capacities of pile commonly used in practice? •Axial capacity •Lateral capacity •Pullout capacity or Tension capacity 04/03/2009
- 21. How to estimate the capacity of a Pile? What are the approaches? The two approaches for obtaining capacity of the pile are Field approach In this approach the pile is loaded to the desired level and its capacity is estimated. Theoretical Approach In this approach the pile capacity is calculated using some formulae into which soil data is fed for obtaining the capacity. 04/03/2009
- 22. Field Approach A Test pile of required dimensions is constructed in the field and a load test is conducted to assess the capacity of the pile. This approach gives more realistic estimate of pile capacity. However it is time consuming and costly 04/03/2009
- 23. Load Tests On a Single Pile The load tests are categorized as Stress tests •Maintained load test ( Static vertical load test) •Constant rate of penetration test •Lateral load test •Dynamic load test •Cyclic load test ( not discussed in this presentation) Strain tests •Low strain integrity testing •High strain integrity testing. 04/03/2009
- 24. Pile load tests are usually carried out for the following main reasons: •To obtain back figured soil data that will enable other piles to be designed •To confirm pile lengths and hence contract costs before the client is committed to over all job costs •To counter check results from geotechnical and pile driving formulae •To determine the load-settlement behavior of the pile, especially in the region of anticipated working load, that the data can be used for prediction of group settlement. •To verify the structural soundness of the pile. 04/03/2009
- 25. Field setup for a Static Axial compressive load test on a single pile Test Schematic Real time field set up Figure 9 04/03/2009
- 26. Determination of pile axial compressive capacity from static load test The Pile load test data is presented as shown below Figure 10 From the above plots the ultimate pile load is commonly taken as the load where the load settlement curve approaches a vertical asymptote 04/03/2009 Contd. Next slide
- 27. Lateral Load test Just like axial capacity, lateral capacity of pile can also be obtained by conducting lateral load tests in the field Steel Piles Typical lateral load test setup for steel piles – See pile No 2 in Picture. Figure 11 04/03/2009 Contd. next slide
- 28. inclinometer Loading rod Lateral Loading is applied through the rod on to the pile by means of a Hydraulic jack 04/03/2009 Figure 12
- 29. Pullout or Tension Capacity – Field test Just like axial pile load test, pullout load test is done by applying load in the opposite direction The load test setup is similar to the axial compressive load test with little modifications. 04/03/2009
- 30. Typical Pullout/Tensile load test setup Figure 13 04/03/2009
- 31. Theoretical Approach Data required • Soil parameters like cohesion c, angle of internal friction ø, adhesion factor between soil and pile material, etc. • SPT Values ( N values). • Average cone resistance in case of CPT, etc. 04/03/2009
- 32. Axial Capacity The fundamental equation for axial capacity of pile is QU = Qb + Qs Where QU = Ultimate Load carrying capacity of pile Qb =End bearing resistance= qbAb Qs = Skin friction resistance= fs As Where qb = Ultimate unit bearing capacity at base Ab = Bearing area of the pile base fs = Unit skin friction As = Surface area of the portion of pile embedded in soil. 04/03/2009
- 33. Qb = qb Ab Where qb = unit point bearing capacity ( similar to bearing capacity of shallow foundation) = c’ Nc* + q’ Nq* + γ D Nγ* c’ = effective cohesion of the soil supporting pile tip q’ = effective vertical stress at the level of pile tip D= width of the pile γ= unit weight of the soil Nc* Nq* Nγ* are bearing capacity factors that include shape and depth factors 04/03/2009
- 34. In the bearing capacity equation the term γ D Nγ* can be neglected with very small error as D is relatively small compared to length of the pile. •Researchers Meyerhoff, Vesic, etc have suggested various methods for the estimation of Qb •The methods proposed by various researchers primarily focused on determination of the parameters Nc* Nq* Nγ* ( Refer the book “Principles of Foundation Engineering by B.M.Das -5th Edition” for the above methods) 04/03/2009
- 35. Qs = fs As Where fs = unit frictional resistance As = Surface area of the pile For determining fs three methods are commonly used and they are called the α-method, β-method and λ-method ( Refer the book “Principles of Foundation Engineering by B.M.Das- 5th Edition” for the above methods) 04/03/2009
- 36. Lateral Capacity of Piles • Piles are subjected to lateral loads in addition to axial loads • However for simplicity a pile subjected to only lateral load is usually studied for analytical convenience. • Unlike axial capacity, the determination of lateral capacity of the pile is a complex problem. • The lateral capacity of piles tested in the field is dictated by the lateral deflection criteria of local codes 04/03/2009
- 37. A vertical pile resists lateral load by mobilizing passive pressure in the soil surrounding it. The degree of distribution of the reaction of surrounding soil depends on the following • The stiffness of the surrounding soil • The stiffness of the pile •The fixity of the ends of the pile 04/03/2009
- 38. • The laterally loaded pile unlike an axially loaded pile is a three dimensional problem. • In case of circular pile, the problem can be analyzed as two-dimensional due to symmetry. • A laterally loaded pile can deflect in any direction depending on the direction of the lateral load. 04/03/2009
- 39. Categories of laterally loaded piles Laterally loaded piles are divided into two categories based on variation of deflection, shear and moment, as shown below Rigid pile Flexible pile Figure 14 Figure 15 04/03/2009
- 40. The lateral capacity of a pile is usually defined as the load corresponding to a specified deflection of pile head from its plumb. The amount of this deflection is usually suggested by the local codes based on the structure(s) for which the pile foundation is designed. 04/03/2009
- 41. Laterally loaded pile: theory The stresses/forces mobilized immediately after the lateral load is applied, are depicted below ( For piles of other shapes also the same forces are mobilized) Figure 16: Forces mobilized around circular pile subjected to lateral loading( Plan view) 04/03/2009
- 42. As shown in the Figure 7, the plane x-z is assumed to be the principal plane of the pile cross section. Due to the moment ‘Mo’ and shear ‘Vo’ applied at the pile head, each point on the pile undergoes a translation ‘u’ in the x-direction and rotation θ about y-axis. The surrounding soil develops pressures ‘p’ at each point to resist the lateral displacement ‘u’ of the pile. The principles of continuum mechanics and correlations with the results of tests on instrumented laterally loaded piles were used to relate ‘u’ at each point with corresponding ‘p’. The relationship between ‘p’ and ‘u’ is presented as non-linear curve famously known as p-u curve (in some literature referred as p-y curve). All p-u curves are developed for monotonically increasing static loads and the static curve is then altered by various techniques to account for degradation effects due to cyclic loading 04/03/2009
- 43. A general method for moments, shear forces and displacements for a vertical pile embedded in a granular soil and subjected to moment and shear at the ground surface as shown in Figure 7 was given by Matlock and Resse(1960). The following are the equations proposed by them based on theory of beam on elastic foundation 04/03/2009
- 44. Simplified solution Broms (1965) developed a simplified solution for ultimate lateral resistance of piles based on the following assumptions. • shear failure of surrounding soil (in case of rigid piles) • bending of the pile by plastic yield resistance of pile section ( in case of flexible piles) Broms’s solutions for ultimate resistance of rigid and flexible piles are shown in the next slide 04/03/2009
- 45. sand sand clay clay (a) (b) Broms’s solution for ultimate resistance of rigid piles (a) and flexible piles (b) Figure 17 04/03/2009
- 46. Uplift Capacity of Piles The major components resisting uplift forces on pile foundation are skin friction and self weight of the pile. ( refer Figure 8) So the governing equation for uplift capacity is Frictional resistance Quplift = fs As + Weight of the pile 04/03/2009
- 47. The capacity of the pile (Axial/Lateral/Uplift) either arrived by field approach or theoretical approach is called Ultimate capacity which is divided with a factor to arrive at safe carrying capacity of the pile. The ultimate capacity is usually dictated by the limitations on settlements as per local engineering codes The main purpose of under reporting the pile capacity by dividing it with a factor of safety is to accommodate various un certainties in •Soil strata •Loading and •Possible reduction in strength of sub soil strata due to installation technique, etc. 04/03/2009
- 48. Pile groups • Most pile foundations contain group of piles instead of single pile • The supporting capacity of a group of ‘n’ similar piles in many cases (not in all cases) is ≤ ‘n’ times the capacity of a single pile- reason being the zone of soil or rock stressed by the entire group extends to much greater width and depth than that by a single pile as shown in the figure Figure 18 04/03/2009
- 49. Analysis of pile groups There are three methods commonly used to analyze pile group: •Simple static analysis: This method ignores the presence of soil and assumes pile group as an isolated structural system. It also assumes zero moment at the head of each pile. •Equivalent bent analysis: This method considers the soil sub grade reaction on the equivalent free standing length of the piles. The pile cap is assumed to be rigid and piles are assumed to behave elastically. •Elastic continuum analysis: The soil is considered as elastic material that is consistent through out its mass. 04/03/2009
- 50. In comparing various methods of analysis, the vertical loads are similar, but elastic continuum method predicts higher maximum load. The equivalent bent method which ignores presence of soil predicts higher pile rotations/moments than elastic continuum method. Pile group efficiency factor(η) is usually calculated using any of the following six methods 1) Converse labarre’s method Where, ‘ni’ represents no. of rows and columns ‘d’ is the dia of the pile and ‘s’ c/c spacing between adjacent piles. 04/03/2009
- 51. 2) Feld’s rule: reduces the capacity of each pile by 0.0625 for each adjacent pile. The spacing of piles is not considered. 3) Contractor’s rule: The pile capacity is reduced by a factor I for each adjacent pile where I =d/8s 4) Sand’s rule: Used for pile carried through friction in sand 5) Los Angles group action method: 6) Seiler- Keeney method: 04/03/2009
- 52. 04/03/2009
- 53. Important points to remember regarding pile groups •Pile groups driven into granular soils may provide reinforcement to soil and the group efficiency factor may reach up to 2. •In contrast the efficiency factor of pile group driven into cohesive soils may be less than 1. •Under axial or lateral load, instead of failure of individual piles in the group, block failure may arise as shown in the below figure Initial position of the block Position of block after settlement 04/03/2009 Figure 19
- 54. • independent calculations showing the capacity of block or group of pile and capacity of individual piles should be made • Relate the ultimate capacity of the block to sum of ultimate capacities of individual piles in the group i.e. find the ratio of ultimate capacity of block to sum of ultimate capacities of all piles in the group. This ratio should not be preferably less than 1 Ultimate Axial Capacity Ultimate capacity of pile group is usually the smaller of a) Ultimate capacity = m x n ( ultimate capacity of single pile in the group) where m= no. of rows and n= no. of columns in the group (in plan view) b) Ultimate capacity = L * B *(unit bearing resistance) + 2*(L+B) *Unit frictional resistance Where L& B are plan dimensions of imaginary block encircling the pile group Note the above formulae are based on the assumption that the line of action of loading coincides with the C.G of the group (i.e no moments) 04/03/2009
- 55. Ultimate Uplift Capacity Figure 20 04/03/2009where Tg is the combined uplift capacity of group and Ti sum of uplift capacities of all individual piles
- 56. Ultimate Lateral capacity There are two common problems in the analysis of pile groups subjected to lateral loading 1.The computation of loads coming on to each pile in the group and 2.The computation of efficiency of group of closely spaced piles. The ultimate lateral capacity, unlike axial capacity, of pile group cannot be presented as a simple equation due to the mathematical difficulty in establishing a proper relationship between the following INTERACTING FACTORS in addition to those associated with determining the lateral capacity of single pile. Stiffness and density of soil in front of the pile cap Depth of cap embedment in the soil Rotational restraint at the pile head by virtue of its embedment into the pile cap Pile group axial capacity Stiffness and density of soil around the piles Location of Pile cap i.e. above or below soil Cyclic and sustained loads However, an analytical method called Group Equivalent Pile (GEP) method can be used with considerable accuracy for developing p-u curves for pile cap and piles in the group. In GEP, p-u curves are obtained by multiplying the ‘p’ values of single pile with a modification factor to account for interaction effects and summing the modified ‘p’ values of all piles in the group to obtain p-u curves for the group 04/03/2009
- 57. Factors influencing pile capacities • The surrounding soil • installation technique like driven or bored •Method of construction ( pre cast or cast in situ) •Spacing of piles in a group •Symmetry of the group •Location of pile cap i.e. above or below soil •Shape of the pile cap, etc. •Location of pile in the group •Drainage conditions in soil Go through references given at the end of presentation to learn about theoretical determination of pile capacities due to the reasons mentioned above 04/03/2009
- 58. Settlement Analysis Piles are subjected to the settlement due to the vertical loads coming on to them from the structure supported by them . The total settlement of a single pile has the following components •Elastic settlement of the pile (se1) •Settlement of the pile caused by the load at the pile tip(se2) •Settlement of the pile caused by load transfer along the pile shaft (se3). The formulae for calculating the above –mentioned settlements are given in the next slide 04/03/2009
- 59. (Qwp + ξQws ) L q wp D(1 − µ 2 ) I wp se1 = se2 = Ap E p Es Qws D(1 − µ 2 s ) I ws se3 = ρLE S Where, Qwp = load carried at the pile tip resting on the soil, under working load condition Qws = load carried by skin friction under working load condition L= Length of the pile Ep = Modulus of elasticity of pile material Ap = Area of cross section of pile material qwp = load at pile tip per unit area µs = poissons ratio of the soil Iwp Iws = influence factors 04/03/2009
- 60. Settlement of pile groups 04/03/2009
- 61. 04/03/2009 Figure 21
- 62. 04/03/2009
- 63. Design Steps Design of pile foundation involves the following steps 1)Calculating the ultimate and then safe carrying capacity of pile of given material for a given soil data using the theoretical methods or obtaining the above-mentioned capacity from field test. 2)Arriving at the number of piles required for a given loading from the structure by considering the group effects on piles. 3)Designing the pile cap, which is usually considered as rigid member in a pile group. 04/03/2009
- 64. 4) Calculating the distribution of forces , from the superstructure, in the piles and ensuring that the force on any pile in a group doesn’t exceed its safe carrying capacity. 5) Finally carrying out settlement analysis to ensure that the settlements are within the limits Note: There are several mathematical procedures for calculating the capacity in various kinds of soil viz. cohesive, granular, and cohesive-granular and also to calculate the capacity based on method of installation i.e. driven or bored. Please refer the literature given in the references at the end to understand the procedures. 04/03/2009
- 66. Negative Skin Friction What is negative skin friction? Negative skin friction is a downward shear drag acting on the pile surface due to relative downward movement of soil strata surrounding the pile. The following are some of the causes of negative skin friction •Due to pile or pile segment passing through compressible soil stratum which consolidates •Due to placement of a fill on compressible soil layer causing the layer to consolidate •Lowering of ground water table causing the shrinkage of expansive soils. •Under consolidated natural or compacted soils. If the pile tip is on a stiff or hard stratum, there will be a relative downward movement of upper compressible layer of soil w.r.t. pile , due to above causes, causing a downward drag force. 04/03/2009
- 67. Initial position of compressible deposit final position of compressible deposit Downward drag( negative skin friction) Figure 22 •Vesic stated that downward movement as little as 0.6 inch may be sufficient to mobilize full negative skin friction. •The down drag will not affect the geotechnical capacity of end-bearing piles but will increase stresses on the pile and pile cap. The negative skin friction of a single pile is given by Negative skin friction load = Unit frictional resistance (downward)* Length of the pile above bottom of the compressible layer * Perimeter of the pile cross section And total downward load= negative skin friction load + live load + dead load 04/03/2009
- 68. For a pile group it can be assumed that there is no relative movement between the piles and the soil between the piles. Therefore the total force acting down is equal to the weight of the block of soil held between the piles, the weight of the piles and the pile cap and the downward drag along the pile group perimeter due to negative skin friction A Pheripheral downdrag SEC A 04/03/2009 Figure 23
- 69. Socketed Piles What are socketed piles? Socketed piles are usually end bearing piles which are socketed into a weathered/soft rock. What is weathered rock? •Soil consolidates to Rock •Rock weathers to Soil The in between phase of the above two is called as weathered rock /soft rock 04/03/2009
- 70. Pile Socketed into weathered rock M H Pile Sand Soil over Stiff clay burden Murum Socket length Soft/ weathered rock Pile Tip Solid rock Figure 24 04/03/2009
- 71. Why socketing? The common belief is socketing pile into a soft or weathered rock will improve the capacities of piles to lateral loads when the surrounding soil above the rock is weak. The depth of socket is designed based on •Local experience/empirical formulae: Usually a socket of depth varying from 2 to 5 times the diameter of the pile. •By a more systematic approach called COLE and STROUD approach ( is not discussed here as it out of scope of this presentation) 04/03/2009
- 72. Dynamic testing of Piles Dynamic pile testing is fast and effective method for assessing bearing capacity of the foundation that requires instrumenting deep foundations with accelerometers and strain transducers and analyzing the data collected by these transducers. The Procedure is standardized by ASTM D 4945 ( Standard test method for high strain dynamic testing of piles. The testing in addition to bearing capacity gives shaft resistance and point bearing resistance distribution and also evaluates the shape and integrity (please refer pile integrity in this presentation for more details) of the foundation 04/03/2009
- 73. •Dynamic pile testing is a supplement to static testing for evaluating pile capacity. •The Dynamic pile testing is categorized as ---- High strain dynamic testing and ------Low strain dynamic testing High strain dynamic testing is used to provide data on force and acceleration of pile subjected to impact force. The data is used to evaluate the bearing capacity/capacity and structural integrity of the pile as well as hammer performance, pile stresses and soil characteristics like soil damping coefficients. Pile integrity which is accurately evaluated on site will allow the engineer to immediately reject or accept the pile. Low strain pile testing is exclusively used for testing integrity ( continuity of pile). It also gives information on physical dimension and consistency of the pile material. 04/03/2009
- 74. Setup to produce impact on the pile Data collector and Analyzer called pile driving analyzer ( PDA) Figure 25:Dynamic pile testing setup 04/03/2009
- 75. Another picture showing setup for dynamic pile testing Figure 26 04/03/2009
- 76. The data obtained from dynamic pile testing i.e. force and velocity measurements of pile are fed to a software program called “ Case Pile Wave Analysis Program( CAPWAP) “ which is used to simulate static pile load test . A typical CAPWAP procedure uses the following steps. 1.Retrieve data from pile driving analyzer (collects force and velocity data) 2.Setup pile model 3.Assume soil resistance parameters 4.Perform analysis using one of the measured quantities ( force or velocity) as input and calculate the other. 5.Compare measured with computed quantity 6.If match is not satisfactory, adjust soil resistance parameters and go to step 4 7.Out put soil model when satisfactory match is obtained and simulate static test. 04/03/2009
- 77. Pile integrity testing What is pile integrity testing? A pile integrity test also known as low strain dynamic testing is used to check •Potentially dangerous defects such non uniform cross section, voids, cracks, etc in the casted pile foundation. •Integrity of pile in its total length. •To determine unknown length of pile in existing structures 04/03/2009
- 78. When cast in-situ piles are constructed, the following defects may occur, hence the main objectives in the pile integrity testing is to provide the client/consultants information about : a) honeycombing due to inadequate vibration. b) segregation due to over vibration and improper concrete placement methods. c) washouts of cement due to groundwater flow. d) cracks in pile shaft due to shrinkage. e) inclusion of foreign material causing contamination of the concrete. f) necking of the pile due to collapse of side walls during withdrawal of the temporary casings 04/03/2009
- 79. Dynamic loading on piles The following are the most common situations in which piles are subjected to dynamic loading •Pile driving •Piles supporting dynamic equipment •Earthquake 04/03/2009
- 80. Pile driving •Usually ‘Driven’ piles are driven into the ground by impact force which causes considerable stresses in the piles. •The forces and accelerations induced in the pile during driving are recorded using a data logger called Pile Driving Analyzer( PDA). •The data obtained by PDA will be used to study the pile integrity and potentially dangerous defects like honey combing, cracks, presence of foreign matter, etc. •The PDA works on the principles of wave propagation. 04/03/2009
- 81. Piles supporting dynamic equipment. Piles supporting dynamic equipment are usually subjected to impact and periodic forces which act continuously for a long time. This results in a complex soil- structure problem which calls for a rigorous analysis. Foundation for dynamic equipment is its self a research area. To give a preliminary idea some figures are presented below. Machine(rotating, reciprocating or impact type) Pile cap Figure 27:Machine on pile foundation 04/03/2009 Contd. Next slide
- 82. Figure 28: Modes of vibration of machine which are transferred to the piles supporting the foundation Researchers Novak, Donavan, Stevens, Indrajit Chowdhury, etc proposed simple but reliable solutions for the analysis of piles/pile groups subjected to dynamic loading. Several researchers also proposed more complex and rigorous solutions using FEM techniques. 04/03/2009
- 83. Earthquake loading on piles. Earthquake loading is catastrophic for the pile foundation due to the fact that it induces very high lateral loading from the surrounding soil and the superstructure it carries causing a flexural failure of the pile due to its slenderness. Hence, this calls for a rigorous study of pile response to earthquake loading using complex mathematical/computational methods Figure 29: Potential failure modes of pile foundations subjected to seismic loading 04/03/2009
- 85. Pile installation is as important as design. In this section, two types of methods: a)Installation by Driving b)Installation by Boring Are presented in the subsequent slides 04/03/2009
- 86. Before going through pile installation methods understand the following terminology. Driven pre-cast pile: The pile is casted in a yard brought to the site and driven by some mechanism into the soil Driven Cast-in-situ pile: A casing plugged at bottom is driven into the ground and then the pile is casted by removing or retaining the casing Bored Pre-cast pile: A bore is made and the soil inside is removed and then a pile casted in some yard is put into the bore Bored Cast -in-situ pile: A bore is made the soil is removed and the pile is casted at site in the bore. 04/03/2009
- 87. Installation by Driving •If the driving has to be carried out by hammer, the following factors should be take into consideration. •The size and weight of the pile •The driving resistance which has to be overcome to achieve the desired penetration •The available space and head room in the site ( because the hammer has to be dropped from certain height and also the initial height is approximately height of the pile + height of fall of the hammer) •The availability of cranes •The noise restrictions which may be in force in the locality 04/03/2009
- 88. Schematics of pile driving with hammer Hammer guide Drop hammer Pile( pre cast) or Casing( cast-in-situ) Soil Driving shoe Figure 30 04/03/2009
- 89. Methods of pile driving • Dropping weight • Explosion • Vibration • Jacking ( only for micro piles) • Jetting 04/03/2009 Figure 31: Hammer driven pile-real time
- 90. Installation by Boring Figure 32 : Installation by mechanical auger schematics 04/03/2009
- 91. Figure 33: Mechanical Auger-real time 04/03/2009
- 92. Figure 34: Rotary Bored Piling- real time 04/03/2009
- 93. Advantages and Disadvantages of various piles 04/03/2009
- 94. 04/03/2009
- 95. 04/03/2009
- 97. Pile driving formulae To develop the desired load carrying capacity, a point bearing driven pile must penetrate sufficiently into a dense soil layer or have sufficient contact with a layer of rock. This requirement cannot always be satisfied by driving a pile to a pre-determined depth, because soil profiles vary. For that reason several formulae have been developed to calculate the ultimate capacity of the pile during driving. They are based on Energy Approach and are independent of the soil into which pile is driven. Some of the formulae are given below. The reader is requested to go through literature suggested in references at the end. The famous of these formulae is Engineer’s news ( EN) record formula. The modified form of this formula is presented below Qu = (E WR h)*(WR + n2WP) / ( S+C)*(WR +WP) 04/03/2009 Contd. Next Slide
- 98. Where, Qu = Ultimate capacity of the pile WR = Weight of the ram h= height of fall of the ram Wp= Weight of the pile C= a constant S=Penetration of pile per hammer blow n= Coefficient of restitution between ram and pile cap E= Efficiency of the hammer 04/03/2009
- 99. Pile cap configurations 04/03/2009 Figure 35
- 100. Figure 36 04/03/2009
- 101. Structural Design of Pile and Pile cap Structurally the pile section is designed as column for •Compression plus Bending •Tension plus bending The pile cap is designed as rigid or flexible. •A rigid ( very high flexural strength between two adjacent piles) pile cap is designed for one way shear and punching shear. •A flexible ( average flexural strength between piles) pile cap is analyzed by FEM by considering the piles as vertical springs and then designed for the stresses obtained from the analysis 04/03/2009
- 102. Flow chart for pile selection 04/03/2009 Figure 37
- 103. Real time Pictures of Piles Figure 38 04/03/2009
- 104. Figure 39 04/03/2009
- 105. 5.References Please refer the below books for detailed info on pile foundations. For purpose of industrial practice: •Principles of Foundation Engineering by B.M.Das •Foundation Analysis and Design by Joseph. E.Bowels •Foundation Design Manual for Practicing Engineers by Narayan.V.Naik •Foundation Design by Wayne.C.Teng For advanced information on the subject: •Pile foundation Analysis and Design by Poulus.H.G. and E.H.Davis •Foundation Design and Construction by Tomlinson.M.J. •Deep foundations by United Facility Criteria ( UFC) – US Army 04/03/2009
- 106. Thank You 04/03/2009