Ultrasonic Testing

Introduction This module presents an introduction to the NDT Ultrasonic testing uses high frequency sound
method of ultrasonic testing.
energy to conduct examinations and make measurements.

Ultrasonic examinations can be conducted on a

A considerable amount of information about the
wide variety of material forms including castings, forgings, welds, and composites.

part being examined can be collected, such as the presence of discontinuities, part or coating thickness; and acoustical properties can often be correlated to certain properties of the material.

Outline

Applications Basic Principles of sound generation Pulse echo and through transmission testing Inspection applications Equipment Transducers Instrumentation Reference Standards Data presentation Advantages and Limitations Glossary of terms

Basic Principles of Sound Sound is produced by a vibrating body and travels

in the form of a wave. Sound waves travel through materials by vibrating the particles that make up the material. The pitch-Refers to frequency of the wave (A high pitch sound High audible frequency.) Sub sonic vibration=16 Hz 0.5 MHz To 25 MHz

Basic Principles of Sound (cont.)

The measurement of sound waves from crest to crest determines its wavelength (). The time is takes a sound wave to travel a distance of one complete wavelength is the same amount of time it takes the source to execute one complete vibration. The sound wavelength is inversely proportional to its frequency. ( = 1/f) Several wave modes of vibration are used in ultrasonic inspection. The most common are longitudinal, shear, and Rayleigh (surface) waves.

Modes of propagation
In solids, sound waves can propagate in four principal modes that are based on the way the particles oscillate. Sound can propagate as longitudinal waves, shear waves, surface waves, and in thin materials as plate waves. Longitudinal and shear waves are the two modes of propagation most widely used in ultrasonic testing. The particle movement responsible for the propagation of longitudinal and shear waves is illustrated in the figure.

In

longitudinal waves, the oscillations occur in the longitudinal direction or the direction of wave propagation. Since compression and expansion forces are active in these waves, they are also called pressure or compression waves. They are also sometimes called density waves because material density fluctuates as the wave moves. Compression waves can be generated in gases, liquids, as well as solids because the energy travels through the atomic structure by a series of compressions and expansion movements.

In the transverse or shear waves, particles oscillate at a right angle or transverse to the direction of propagation. Shear waves require an acoustically solid material for effective propagation, and therefore, are not effectively propagated in materials such as liquids or gasses. Shear waves are relatively weak when compared to longitudinal waves. In fact, shear waves are usually generated in materials using some of the energy from longitudinal waves.

Surface (or Rayleigh) waves travel at the surface of a relatively thick solid material penetrating to a depth of one wavelength. A surface wave is a combination of both a longitudinal and transverse motion which results in an elliptical motion as shown in the image. The major axis of the ellipse is perpendicular to the surface of the solid.

Plate (or Lamb) waves are similar to surface waves except they can only be generated in materials a few wavelengths thick (thin plates). Lamb waves are complex vibrational waves that propagate parallel to the test surface throughout the thickness of the material. They are influenced a great deal by the test wave frequency and material thickness. Lamb waves are generated when a wave hits a surface at an incident angle such that the parallel component of the velocity of the wave (in the source) is equal to the velocity of the wave in the test material. Lamb waves will travel several meters in steel and so are useful to scan plate, wire, and tubes.

Basic Principles of Sound (cont.)

Ultrasonic waves are very similar to
light waves in that they can be reflected, refracted, and focused. Reflection and refraction occurs when sound waves interact with interfaces of differing acoustic properties. In solid materials, the vibrational energy can be split into different wave modes when the wave encounters an interface at an angle other than 90 degrees. Ultrasonic reflections from the presence of discontinuities or geometric features enables detection and location. The velocity of sound in a given material is constant and can only be altered by a change in the mode of energy.

Ultrasound Generation
Ultrasound is generated with a transducer. A piezoelectric element in the transducer converts electrical energy into mechanical vibrations (sound), and vice versa.

The transducer is capable of both transmitting and receiving sound energy.

Principles of Ultrasonic Inspection

Ultrasonic waves are introduced into a material

where they travel in a straight line and at a constant speed until they encounter a surface.

At surface interfaces some of the wave energy is

reflected and some is transmitted.

The amount of reflected or transmitted energy can

be detected and provides information about the size of the reflector.

The travel time of the sound can be measured and

this provides information on the distance that the sound has traveled.

Test Techniques Ultrasonic testing is a very versatile inspection

method, and inspections can be accomplished in a number of different ways. Ultrasonic inspection techniques are commonly divided into three primary classifications. Pulse-echo and Through Transmission

Normal Beam and Angle Beam (Relates to the angle that the sound energy enters the test article) Contact and Immersion
(Relates to the method of coupling the transducer to the test article)

(Relates to whether reflected or transmitted energy is used)

Each of these techniques will be discussed briefly in the following slides.

Properties of sound wave

Velocity Wave length Reflection Refraction Couplant Water, kerosene, oil ,kerosene,
wall paper paste , spl gel Mode conversion Beam characteristics Absorption, scatter

Test Techniques - Pulse-Echo

In pulse-echo testing, a transducer sends out a pulse of energy and the same or a second transducer listens for reflected energy (an echo). Reflections occur due to the presence of discontinuities and the surfaces of the test article. f The amount of reflected sound energy is displayed versus time, which provides the inspector information about the size and the location of features that reflect the sound.
initial pulse

back surface echo

crack echo

crack plate
0 2 4 6 8 10

UT Instrument Screen

Test Techniques Pulse-Echo (cont.)

Digital display showing signal generated from sound reflecting off back surface. Digital display showing the presence of a reflector midway through material, with lower amplitude back surface reflector.
The pulse-echo technique allows testing when access to only one side of the material is possible, and it allows the location of reflectors to be precisely determined.

Test Techniques Through-Transmission

Two transducers located on opposing sides of the test specimen are used. One transducer acts as a transmitter, the other as a receiver. Discontinuities in the sound path will result in a partial or total loss of sound being transmitted and be indicated by a decrease in the received signal amplitude. Through transmission is useful in detecting discontinuities that are not good reflectors, and when signal strength is weak. It does not provide depth information.
0
1 1 T R

1 1

10

Test Techniques Through-Transmission

Digital display showing received sound through material thickness.

Digital display showing loss of received signal due to presence of a discontinuity in the sound field.

Test Techniques Normal and Angle Beam

In normal beam testing, the sound beam is introduced into the test article at 90 degree to the surface. In angle beam testing, the sound beam is introduced into the test article at some angle other than 90. The choice between normal and angle beam inspection usually depends on two considerations:
- The orientation of the feature of interest the sound should be directed to produce the largest reflection from the feature. - Obstructions on the surface of the part that must be worked around.

Test Techniques Contact Vs Immersion

To get useful levels of sound energy into a material, the air between the transducer and the test article must be removed. This is referred to as coupling. In contact testing (shown on the previous slides) a couplant such as water, oil or a gel is applied between the transducer and the part. In immersion testing, the part and the transducer are place in a water bath. This arrangement allows better movement of the transducer while maintaining consistent coupling. With immersion testing, an echo from the front surface of the part is seen in the signal but otherwise signal interpretation is the same for the two techniques.
1 2 IP FWE

1
BWE

IP

FWE

2
BWE

DE

IP = Initial Pulse FWE = Front Wall Echo DE = Defect Echo BWE = Back Wall Echo

Defect

8 10

8 10

Inspection Applications
Some of the applications for which ultrasonic testing may be employed include: Flaw detection (cracks, inclusions, porosity, etc.) Erosion & corrosion thickness gauging Assessment of bond integrity in adhesively joined and brazed components Estimation of void content in composites and plastics Measurement of case hardening depth in steels Estimation of grain size in metals On the following slides are examples of some common applications of ultrasonic inspection.

Thickness Gauging Ultrasonic thickness

gauging is routinely utilized in the petrochemical and utility industries to determine various degrees of corrosion/erosion.
Applications include piping systems, storage and containment facilities, and pressure vessels.

Flaw Detection - Delaminations

Contact, pulse-echo inspection for delaminations on 36 rolled beam.

Signal showing multiple back surface echoes in an unflawed area.

Additional echoes indicate delaminations in the member.

Flaw Detection in Welds One of the most widely

used methods of inspecting weldments is ultrasonic inspection. Full penetration groove welds lend themselves readily to angle beam shear wave examination.

Equipment
Equipment for ultrasonic testing is very diversified. Proper selection is important to insure accurate inspection data as desired for specific applications. In general, there are three basic components that comprise an ultrasonic test system: - Instrumentation - Transducers - Calibration Standards

Transducers
Transducers are manufactured in a variety of forms, shapes and sizes for varying applications. Transducers are categorized in a number of ways which include: - Contact or immersion - Single or dual element - Normal or angle beam In selecting a transducer for a given application, it is important to choose the desired frequency, bandwidth, size, and in some cases focusing which optimizes the inspection capabilities.

Contact Transducers
Contact transducers are designed to withstand rigorous use, and usually have a wear plate on the bottom surface to protect the piezoelectric element from contact with the surface of the test article. Many incorporate ergonomic designs for ease of grip while scanning along the surface.

Contact Transducers (cont.)

Contact transducers are
available with two piezoelectric crystals in one housing. These transducers are called dual element transducers.

One crystal acts as a transmitter,

the other as a receiver.

This arrangement improves near

surface resolution because the second transducer does not need to complete a transmit function before listening for echoes.

Dual elements are commonly

employed in thickness gauging of thin materials.

Contact Transducers (cont.)

A way to improve near surface
resolution with a single element transducer is through the use of a delay line. Delay line transducers have a plastic piece that is a sound path that provides a time delay between the sound generation and reception of reflected energy. Interchangeable pieces make it possible to configure the transducer with insulating wear caps or flexible membranes that conform to rough surfaces. Common applications include thickness gauging and high temperature measurements.

Transducers (cont.) Angle beam transducers

incorporate wedges to introduce a refracted shear wave into a material. used with the material velocity to determine the desired refracted shear wave according to Snells Law) or variable wedge angles. weld examination.

The incident wedge angle is

Transducers can use fixed Common application is in

Transducers (cont.) Immersion transducers are

designed to transmit sound whereby the transducer and test specimen are immersed in a liquid coupling medium (usually water).

Immersion transducers
are manufactured with planar, cylindrical or spherical acoustic lenses (focusing lens).

Instrumentation
Ultrasonic equipment is usually purchased to satisfy specific inspection needs, some users may purchase general purpose equipment to fulfill a number of inspection applications. Test equipment can be classified in a number of different ways, this may include portable or stationary, contact or immersion, manual or automated. Further classification of instruments commonly divides them into four general categories: Dmeters, Flaw detectors, Industrial and special application.

Instrumentation (cont.) D-meters or digital

thickness gauge instruments provide the user with a digital (numeric) readout. They are designed primarily for corrosion/erosion inspection applications.

Some instruments provide the user with both a digital readout and a display of the signal. A distinct advantage of these units is that they allow the user to evaluate the signal to ensure that the digital measurements are of the desired features.

Instrumentation (cont.) Flaw detectors are

instruments designed primarily for the inspection of components for defects. evaluated to obtain other information such as material thickness values.

However, the signal can be Both analog and digital

display.

Offer the user options of

gating horizontal sweep and amplitude threshold.

Instrumentation (cont.)

Industrial flaw detection

instruments, provide users with more options than standard flaw detectors. May be modulated units allowing users to tailor the instrument for their specific needs. Generally not as portable as standard flaw detectors.

Instrumentation (cont.)
Immersion ultrasonic scanning
systems are used for automated data acquisition and imaging. They integrate an immersion tank, ultrasonic instrumentation, a scanning bridge, and computer controls. The signal strength and/or the time-of-flight of the signal is measured for every point in the scan plan. The value of the data is plotted using colors or shades of gray to produce detailed images of the surface or internal features of a component.

Images of a Quarter Produced With an Ultrasonic Immersion Scanning System

Gray scale image produced using the sound reflected from the front surface of the coin

Gray scale image produced using the sound reflected from the back surface of the coin (inspected from heads side)

Data Presentation Information from ultrasonic testing can be

Three of the more common formats include: A-scan B-scan C-scan

These three formats will be discussed in the next few slides.

presented in a number of differing formats.

Data Presentation - A-scan

A-scan presentation displays the amount of received ultrasonic energy as a function of time. Relative discontinuity size can be estimated by comparing the signal amplitude to that from a known reflector. Reflector depth can be determined by the position of the signal on the horizontal sweep.
Signal Amplitude

Time

Signal Amplitude

Time

Data Presentation - B-scan

B-scan presentations

display a profile view (cross-sectional) of a test specimen. Only the reflector depth in the cross-section and the linear dimensions can be determined. A limitation to this display technique is that reflectors may be masked by larger reflectors near the surface.

Data Presentation - C-scan The C-scan presentation displays a plan type view
of the test specimen and discontinuities. C-scan presentations are produced with an automated data acquisition system, such as in immersion scanning. Use of A-scan in conjunction with C-scan is necessary when depth determination is desired.

Photo of a Composite Component

C-Scan Image of Internal Features

Calibration Standards
Calibration is a operation of configuring the ultrasonic test equipment to known values. This provides the inspector with a means of comparing test signals to known measurements. Calibration standards come in a wide variety of material types, and configurations due to the diversity of inspection applications. Calibration standards are typically manufactured from materials of the same acoustic properties as those of the test articles. The following slides provide examples of specific types of standards.

Calibration Standards (cont.)

Thickness calibration standards may be flat or curved for pipe and tubing applications, consisting of simple variations in material thickness.
Distance/Area Amplitude standards utilize flat bottom holes or side drilled holes to establish known reflector size with changes in sound path form the entry surface.

ASTM Distance/Area Amplitude

NAVSHIPS

Calibration Standards (cont.)

There are also calibration standards for use in angle beam inspections when flaws are not parallel to entry surface.
IIW

DSC

DC

Rhompas

These standards utilized side drilled holes, notches, and geometric configuration to establish time distance and amplitude relationships.

SC

ASME Pipe Sec. XI

Qualification Standards
Qualification standards differ from calibration standards in that their use is for purposes of varying proper equipment operation and qualification of equipment use for specific codes and standards.
AWS Resolution DC-dB Accuracy

IOW Beam Profile

Advantage of Ultrasonic Testing

Sensitive to both surface and subsurface

Depth of penetration for flaw detection or measurement

Only single-sided access is needed when pulse-echo High accuracy in determining reflector position and Minimal part preparation required. Electronic equipment provides instantaneous results. Detailed images can be produced with automated Has other uses such as thickness measurements, in
addition to flaw detection. technique is used. is superior to other methods.

discontinuities.

estimating size and shape.

systems.

Limitations of Ultrasonic Testing

Surface must be accessible to transmit ultrasound. Skill and training is more extensive than with some other

methods. Normally requires a coupling medium to promote transfer of sound energy into test specimen. Materials that are rough, irregular in shape, very small, exceptionally thin or not homogeneous are difficult to inspect. Cast iron and other coarse grained materials are difficult to inspect due to low sound transmission and high signal noise. Linear defects oriented parallel to the sound beam may go undetected. Reference standards are required for both equipment calibration, and characterization of flaws.

Glossary of Terms
Acoustical properties: ultrasonic material characteristics
such as velocity, impedance, and attenuation. ASTM: acronym for American Society for Testing and Materials. This society is extensively involved in establishing standards for materials and the testing of materials. Back reflection: a display signal that corresponds to the far surface of a test specimen, side opposite to transducer when testing with longitudinal waves. Band width: a range of frequencies either transmitted or received, may be narrow or broad range. B-scan: presentation technique displaying data in a crosssectional view.

Glossary of Terms
Calibration: a sequence of instrument control
adjustments/instrument responses using known values to verify instrument operating characteristics. Allows determination of unknown quantities from test materials. CRT: acronym for Cathode Ray Tube. Vacuum tube that utilizes one or more electron guns for generating an image. C-scan: presentation technique that displays specimen data in a plan type view. DAC (Distance Amplitude Correction-curves): a graphical method of allowing for material attenuation. Percentage of DAC is often used as a means of acceptance criteria. Discontinuity: an interruption in the physical structure of a material, examples include fissures, cracks, and porosity.

Glossary of Terms

IIW: calibration standard meeting the specification of the International Institute of Welding. Longitudinal (Compression) waves: ultrasonic mode of propagation in which the particle vibration is parallel to the direction of propagation. Near Surface Resolution: the ability of an ultrasonic system to display reflectors located close to the entry surface. Pulse-echo: ultrasonic test method that utilizes reflected sound as a means of collecting test data. Rayleigh (Surface) waves: ultrasonic mode of propagation where the sound travels along the surface, particle vibration is elliptical.

Glossary of Terms

Reflection: the changing in direction of sound waves as they strike a surface. Snells Law: an equation of ratios used to determine incident or refracted angle of sound, denotes angle/velocity relationship. Sweep display: horizontal line on the lower portion of the display, often called the time base line. Through transmission: test technique in which ultrasound is transmitted from one transducer and received by a separate transducer on the opposite side of the test specimen. Wavelength: the distance that a sound wave travels as it completes one cycle, normally measured in inches or millimeters.