22,500 - 27,500 LBS.

CAPACITY
HEAVY DUTY D200 SERIES
www.dexteraxle.com
GEARED FOR INNOVATION SINCE 1960
2900 Industrial Parkway East n Elkhart, IN 46516
Phone: 574-295-7888 n Fax: 574-295-8666
1/11 2011 Dexter Axle Company. LIT-121-00
www.dexteraxle.com
This information is intended as a guide for the proper specication and application of Dexter Axle running gear,
associated components and accessories.
Dexter offers a full line of trailer axles that can be used in many different applications. When specifying any
pre-engineered components such as axles, it is the responsibility of the trailer designer to insure compatibility
with the vehicle and all of its sub-systems.
Important Information
The information presented is meant to assist trailer manufacturers in the specication of their running gear
components. Dexter Axle does not warrant that the information given constitutes an approved trailer design
or application. Dynamic loading, travel requirements unique to the trailer design, unusual service conditions,
trailer congurations, unequal load distribution, hitch or coupler arrangements and towing vehicle suspension
characteristics can signicantly affect the performance of any trailer axle and/or suspension systems. It remains
the responsibility of the trailer manufacturer to evaluate, specify and test their trailer/running gear combination
before production and to certify it as such. While the information presented at the time of this writing is current,
it is subject to change as designs and components evolve over time.
Disclaimer of Warranty and Limitation of Liability
All users of this product catalog acknowledge that the information presented is signicantly affected by factors
within the exclusive knowledge of the user including, among other things, service conditions, trailer congurations,
load distributions, hitch and coupler arrangements and tow vehicle suspension characteristics, that the users
have independently investigated these factors and have solely relied on those investigations when using this
catalog, and that it is the responsibility of the user to adequately specify, evaluate and test its trailer/running gear
combinations.
DEXTER AXLE DISCLAIMS ALL WARRANTIES, WHETHER WRITTEN, ORAL OR IMPLIED, IN FACT
OR IN LAW (INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE), ASSOCIATED WITH THE USE OF THE CATALOG AND WITH ANY INFORMATION PRESENTED
BY THIS CATALOG.
Dexter Axle shall not be liable in damages (whether compensatory, punitive, direct, indirect, special, incidental or
consequential) to any user of this catalog under contract, tort, strict liability or any other theory of liability, and any
user agrees to indemnify and hold Dexter Axle harmless from any and all claims, actions or other proceedings
(including attorney fees and court costs) arising out of the use of this catalog to the extent said claims, actions
or other proceedings do not arise out of the sole and exclusive negligence of Dexter Axle.
Load Ratings
The maximum load carrying capacity of any assembly is limited to the lowest load rating of any individual
component selected. For instance, the load rating of a pair of wheels may be lower than other axle components
selected. If this is the case, the load carrying capacity of the axle assembly is reduced accordingly. As a specic
example, if a pair of wheels is rated at 1500 pounds each and is used with other components rated at 4000
pounds per axle, the maximum load capacity is limited to 3000 pounds. If two tires are rated at 1400 pounds
each and are used on this assembly, the maximum load carrying capacity is limited to 2800 pounds.
Introduction
2
Table of Contents
Models and Capacities
22,500-27,500 Lbs ........................................................................................................................................ 3
Available Axle Tracks. .................................................................................................................................... 3
Brake Performance ....................................................................................................................................... 3
Hubs and Drums
12" x 7" Brake Size ................................................................................................................................. 4
16" x 7" Brake Size .................................................................................................................................... 7
Cross Reference ......................................................................................................................................... 11
Hubs & Drums; Wheels & Drums .......................................................................................................... 11
Bearings, Seals, and Caps .................................................................................................................... 12
Anti-Lock Braking Systems (ABS) ............................................................................................................... 13
Tires & Wheels
Clearances and Dimensions ....................................................................................................................... 14
Application Information ............................................................................................................................... 15
Determining Maximum Spring Centers ................................................................................................. 15
Tires, Wheels & Rims ............................................................................................................................ 16
Axle/Brake Components
12" x 7" Brake Size - PQ Style ............................................................................................................. 18
16" x 7" Brake Size - Q Style .................................................................................................................. 20
Tandem Air System
Tandem Air System ..................................................................................................................................... 22
Camshafts
12" x 7" Brake Size ............................................................................................................................... 23
16" x 7" Brake Size .................................................................................................................................. 24
Air Chambers
Service Air Chambers ................................................................................................................................. 25
Spring Brake Air Chambers ........................................................................................................................ 26
Tandem Axle Congurations ....................................................................................................................... 27
Off-Road Applications ........................................................................................................................... 27
Over-the-Highway Applications ............................................................................................................. 28
Suspensions
H-9700 Underslung ..................................................................................................................................... 29
H-9700 Overslung ....................................................................................................................................... 30
Limited Warranty
Dexter Axle Limited Warranty ...................................................................................................................... 31
3
Models and Capacities
Beam Capacity**
Model No. Beam Brake
Highway w/Leaf Springs Air Ride Suspension
D-2L12 5" Light Wall 12" x 7" 22,500 Lbs. n/a +
D-2M12 5" Medium Wall 12" x 7" 25,000 Lbs. 22,500 Lbs.
D-2H12 5" Heavy Wall 12" x 7" 27,500 Lbs. 25,000 Lbs.
D-2L16 5" Light Wall 16" x 7" 22,500 Lbs. n/a +
D-2M16 5" Medium Wall 16" x 7" 25,000 Lbs. 22,500 Lbs.
D-2H16 5" Heavy Wall 16" x 7" 27,500 Lbs. 25,000 Lbs.
** Allowable use of axle capacity ratings (type of service and track/spring center overhang dimension, etc.) and
components vary with application.
+ Light wall tube on models D-2L12 and D-2L16 is not approved for axles equipped with air ride suspensions.
Available Axle Tracks
Tracks are available from 48" to 124".
Brake Performance
The following brake models meet or exceed requirements set forth by Federal Motor Vehicle Safety Standards 121 when
tested under the following conditions:
Brake Size
Wheel Load
*(lbs.)
Rolling Radius
(in.)
A.L. Factor
(consisting of)
12" x 7" 10,000 15.7 Type 30 A/C
6" Slack Adjuster
16" x 7" 10,000 21.3 Type 30 A/C
6" Slack Adjuster
* Wheel Load per wheel end
The permitted use of axles and components, including the capacity ratings that are shown, vary with application and type
of service. The capacities indicated for tires, wheels and axles should be used for general guidelines only.
Dexter Axle disclaims all warranties, whether written, oral or implied, in fact or in law (including any warranty of
merchantability or tness for a particular purpose), associated with the use of the manual and with any information
presented by this manual.
2
2
,
5
0
0

2
7
,
5
0
0

L
B
S
.
M
O
D
E
L
S

A
N
D

C
A
P
A
C
I
T
I
E
S
4
For use with 15" or 17.5" ball seat mounted steel disc wheels
8
7
6
3
1
5
9
10
11
13
14
12
Item Part No. Qty Description Comments
0 008-277-71 1 LH Assembly Hub & Drum 10 Stud 8" BC Use Ball Seat Mtg. Steel Wheels
0 008-277-70 1 RH Assembly Hub & Drum 10 Stud 8" BC Use Ball Seat Mtg. Steel Wheels
ns 008-277-29 1 LH Assembly Hub & Drum 10 Stud 8" BC ABS Use Ball Seat Mtg. Steel Wheels
ns 008-277-28 1 RH Assembly Hub & Drum 10 Stud 8" BC ABS Use Ball Seat Mtg. Steel Wheels
1 008-277-04 1 LH Assembly Hub 10 Stud 8" BC Includes Items 3-5
1 008-277-05 1 RH Assembly Hub 10 Stud 8" BC Includes Items 3-5
ns 008-277-23 1 LH Assembly Hub 10 Stud 8" BC ABS Includes Items 3-5
ns 008-277-22 1 RH Assembly Hub 10 Stud 8" BC ABS Includes Items 3-5
ns 024-200-01 1 ABS Tone Ring Included with ABS Hubs
3 031-026-01 1 Inner Bearing Cup (HM218210)
4 031-027-01 1 Outer Bearing Cup (HM212011)
5 025-056-02 10 LH Shoulder Stud
5 025-056-01 10 RH Shoulder Stud
6 009-040-01 1 Drum 12" x 7"
7 005-102-00 10 Washer
8 006-047-00 10 Hex Nut Drum Mounting
9 006-069-02 10 LH Inner Cap Nut For Steel Disc Wheels
9 006-069-01 10 RH Inner Cap Nut For Steel Disc Wheels
10 006-070-02 10 LH Outer Cap Nut
10 006-070-01 10 RH Outer Cap Nut
11 071-124-00 1 Gasket Oil Cap
12 021-038-02 1 Oil Cap (with vent plug)
13 005-100-00 6 Lock Washer Oil Cap
14 007-157-00 6 Cap Screw Oil Cap
ns - not shown
Hub & Drum Dimensional Information
Item Description Dimensions
A Cup to Cup 3.34"
B Cup to Mounting Face .81"
C Cup to End of Drum 10.57"
D Brake Diameter 12.25"
E Shoe Brake Width 7.50"
F Drum Overall Width 10.50"
G Pilot Diameter 7.12"
H Bolt Circle 8.75"
I Bolt Diameter "
J Hub Cap Hole Mtg "
6 Holes 5.50 BC
Inner Bearing Cup and Cone Overall Stack Thickness 1.575"
10 Stud on 8" Hubs With Inboard Drums
1
2

"

X

7

"

B
R
A
K
E

S
I
Z
E
H
U
B
S

&

D
R
U
M
S
5
For use with 17.5" or 19.5" 221mm piloted disc wheels
5
3
1
4
6
11
13
14
12
10
Item Part No. Qty Description Comments
0 008-396-70 1 Assy Hub & Drum 8 Stud on 275mm BC Use Pilot Mtg. Steel Wheels
ns 008-396-72 1 Assy Hub & Drum 8 Stud on 275mm BC Use Pilot Mtg. Aluminum Wheels
ns 008-396-71 1 Assy Hub & Drum 8 Stud on 275mm BC ABS Use Pilot Mtg. Steel Wheels
ns 008-396-73 1 Assy Hub & Drum 8 Stud on 275mm BC ABS Use Pilot Mtg. Aluminum Wheels
1 008-396-05 1 Assy Hub 8 Stud on 275mm Includes Items 3-5 for Steel Wheels
ns 008-396-06 1 Assy Hub 8 Stud on 275mm Includes Items 3-5 for Aluminum Wheels
ns 008-396-07 1 Assy Hub 8 Stud on 275mm ABS Included Items 3-5 for Steel Wheels
ns 008-396-08 1 Assy Hub 8 Stud on 275mm ABS Includes Items 3-5 for Aluminum Wheels
ns 024-200-01 1 ABS Tone Ring Included with ABS Hubs
3 031-026-01 1 Inner Bearing Cup (HM218210)
4 031-027-01 1 Outer Bearing Cup (HM212011)
5 007-194-00 8 Stud, Press-In M22 x 1.5 2.47" Stud Length for Steel Wheels
5 007-195-00 8 Stud, Press-In M22 x 1.5 3.32" Stud Length for Aluminum Wheels
6 009-116-01 1 Drum 12" x 7"
10 006-118-00 8 Swivel Flange Nut
11 071-124-00 1 Gasket Oil Cap
12 021-038-02 1 Oil Cap (with vent plug)
13 005-100-00 6 Lock Washer Oil Cap
14 007-157-00 6 Cap Screw Oil Cap
ns - not shown
Hub & Drum Dimensional Information
Item Description Dimensions
A Cup to Cup 3.34"
B Cup to Mounting Face .75"
C Cup to End of Drum 10.43"
D Brake Diameter 12.25"
E Shoe Brake Width 7.50"
F Drum Overall Width 11.22"
G Pilot Diameter (Drum) 9.00"
H Bolt Circle 275mm (10.827")
I Bolt Diameter M22 x 1.5
J Hub Cap Hole Mtg "
6 Holes 5.50 BC
Inner Bearing Cup and Cone Overall Stack Thickness 1.575"
J
I
B
G
H D
A
F
E
C
8 Stud on 275mm (10.827") Hubs
With Outboard Drums
1
2

"

X

7

"

B
R
A
K
E

S
I
Z
E
H
U
B
S

&

D
R
U
M
S
6
For use with 15" or 17.5" demountable rims
11
12
13
14
Item Part No. Qty Description
008-269-70 1 Wheel & Drum Assembly - Webb 70159-CCA
008-269-71 1 Wheel & Drum Assembly - Dayton Walther 48-14054-054
008-269-75 1 Wheel & Drum Assembly - Gunite 5785-1
008-269-76 1 Wheel & Drum Assembly - KIC 001-70003H
008-269-72 1 ABS Wheel & Drum Assembly - Dayton Walther 48-15613-056
008-269-73 1 ABS Wheel & Drum Assembly - Webb 70159 CCAT80
008-269-74 1 ABS Wheel & Drum Assembly - Gunite 5785-2
008-269-77 1 ABS Wheel & Drum Assembly - KIC 001-70003TH
11 071-124-00 1 Gasket - Oil Cap
12 021-038-02 1 Oil Cap (with vent plug)
13 005-100-00 6 Lock Washer - Oil Cap
14 007-157-00 6 Cap Screw - Oil Cap
Hub & Drum Dimensional Information
Item Description Dimensions
A Cup to Cup 3.34"
B Cup to Centerline Track 1.36" (w/4.00" spacer)
C Cup to End of Drum 10.57"
D Brake Diameter 12.25"
E Shoe Brake Width 7.50"
F Drum Overall Width 9.07"
G Pilot Diameter 8.50"
H Bolt Circle 10.00"
I Bolt Diameter " (6 holes)
J Hub Cap Hole Mtg "
6 Holes 5.50 BC
K Spacer 15" x 4"
Inner Bearing Cup and Cone Overall Stack Thickness 1.575"
Dimensions listed are referenced for Webb part only. Other cast wheel
suppliers dimensions may be slightly different. Check with supplier.
3Spoke Cast Wheels
1
2

"

X

7

"

B
R
A
K
E

S
I
Z
E
J
I
B
G
H D
A
F
E
C
Wheel & Drum Assembly
H
U
B
S

&

D
R
U
M
S
7
For use with 20", 22.5" or 24.5" ball seat mounted steel disc wheels
8
7
6
3
1
5
9
10
11
4
13
14
12
Item Part No. Qty Description Comments
0 008-279-71 1 LH Assembly Hub & Drum 10 Stud 11" BC Use Ball Seat Mtg. Steel Wheels
0 008-279-70 1 RH Assembly Hub & Drum 10 Stud 11" BC Use Ball Seat Mtg. Steel Wheels
1 008-279-04 1 LH Assembly Hub 10 Stud 11" BC Includes Items 3-5
1 008-279-05 1 RH Assembly Hub 10 Stud 11" BC Includes Items 3-5
3 031-026-01 1 Inner Bearing Cup (HM218210)
4 031-027-01 1 Outer Bearing Cup (HM212011)
5 025-056-02 10 LH Shoulder Stud
5 025-056-01 10 RH Shoulder Stud
6 009-042-01 1 Drum 16" x 7"
7 005-102-00 10 Washer
8 006-047-00 10 Hex Nut - Drum Mounting
9 006-069-02 10 LH Inner Cap Nut For Steel Disc Wheels
9 006-069-01 10 RH Inner Cap Nut For Steel Disc Wheels
10 006-070-02 10 LH Outer Cap Nut
10 006-070-01 10 RH Outer Cap Nut
11 071-124-00 1 Gasket Oil Cap
12 021-038-02 1 Oil Cap (with vent plug)
13 005-100-00 6 Lock Washer Oil Cap
14 007-157-00 6 Cap Screw Oil Cap
ns - not shown
Hub & Drum Dimensional Information
Item Description Dimensions
A Cup to Cup 3.34"
B Cup to Mounting Face .81"
C Cup to End of Drum 9.89"
D Brake Diameter 16.50"
E Shoe Brake Width 7.00"
F Drum Overall Width 9.58"
G Pilot Diameter 9.44"
H Bolt Circle 11.25"
I Bolt Diameter "
J Hub Cap Hole Mtg "
6 Holes 5.50 BC
Inner Bearing Cup and Cone Overall Stack Thickness 1.575"
1
6

"

X

7
"

B
R
A
K
E

S
I
Z
E
10 Stud on 11" Hubs With Inboard Drums
H
U
B
S

&

D
R
U
M
S
8
For use with 20", 22.5" or 24.5" ball seat mounted steel disc wheels
3
5
1
4
6
9
10
11
13
14
12
Item Part No. Qty Description Comments
0 008-290-80 1 LH Assembly Hub & Drum 10 Stud 11" BC Use Ball Seat Mtg. Wheels
0 008-290-79 1 RH Assembly Hub & Drum 10 Stud 11" BC Use Ball Seat Mtg. Wheels
ns 008-290-82 1 LH Assembly Hub & Drum 10 Stud 11" BC ABS Use Ball Seat Mtg. Wheels
ns 008-290-81 1 RH Assembly Hub & Drum 10 Stud 11" BC ABS Use Ball Seat Mtg. Wheels
1 008-290-68 1 LH Assembly Hub 10 Stud 11" BC Includes Items 3-5
1 008-290-67 1 RH Assembly Hub 10 Stud 11" BC Includes Items 3-5
ns 008-290-70 1 LH Assembly Hub 10 Stud 11" BC ABS Includes Items 3-5
ns 008-290-69 1 RH Assembly Hub 10 Stud 11" BC ABS Includes Items 3-5
ns 024-200-01 1 ABS Tone Ring Included with ABS Hubs
3 031-026-01 1 Inner Bearing Cup (HM218210)
4 031-027-01 1 Outer Bearing Cup (HM212011)
5 007-242-01 10 LH Stud, Press-In 1.38 Stud Stand Out Length
5 007-242-00 10 RH Stud, Press-In 1.38" Stud Stand Out Length
6 009-043-03 1 Drum 16" x 7"
9 006-069-02 10 LH Inner Cap Nut For Steel Disc Wheels
9 006-069-01 10 RH Inner Cap Nut For Steel Disc Wheels
9 006-124-02 10 LH Inner Cap Nut For Steel Disc Wheels
9 006-124-01 10 RH Inner Cap Nut For Aluminum Disc Wheels
10 006-070-02 10 LH Outer Cap Nut
10 006-070-01 10 RH Outer Cap Nut
11 071-124-00 1 Gasket Oil Cap
12 021-038-02 1 Oil Cap (with vent plug)
13 005-100-00 6 Lock Washer Oil Cap
14 007-157-00 6 Cap Screw Oil Cap
ns - not shown
Hub & Drum Dimensional Information
Item Description Dimensions
A Cup to Cup 3.34"
B Cup to Mounting Face .73"
C Cup to End of Drum 9.87"
D Brake Diameter 16.50"
E Shoe Brake Width 7.00"
F Drum Overall Width 10.60"
G Pilot Diameter 8.78"
H Bolt Circle 11.25"
I Bolt Diameter "
J Hub Cap Hole Mtg "
6 Holes 5.50 BC
Inner Bearing Cup and Cone Overall Stack Thickness 1.575"
1
6

"

X

7
"

B
R
A
K
E

S
I
Z
E
10 Stud on 11" Hubs With Outboard Drums
H
U
B
S

&

D
R
U
M
S
9
10 Stud on 285.75mm (11.25") Hub Piloted
With Outboard Drums
For use with 20", 22.5" or 24.5" 220mm piloted disc wheels
3
5
1
4
6
10
11
13
14
12
Item Part No. Qty Description Comments
0 008-290-32 1 Assy Hub & Drum 10 Stud 285.75mm BC Use Pilot Mtg. Steel Wheels
ns 008-290-34 1 Assy Hub & Drum 10 Stud 285.75mm BC Use Pilot Mtg. Aluminum Wheels
ns 008-290-33 1 Assy Hub & Drum 10 Stud 285.75mm BC ABS Use Pilot Mtg. Steel Wheels
ns 008-290-35 1 Assy Hub & Drum 10 Stud 285.75mm BC ABS Use Pilot Mtg. Aluminum Wheels
1 008-290-13 1 Assy Hub 10 Stud 285.75mm Includes Items 3-5 for Steel Wheels
ns 008-290-14 1 Assy Hub 10 Stud 285.75mm Includes Items 3-5 for Aluminum Wheels
ns 008-290-16 1 Assy Hub 10 Stud 285.75mm ABS Includes Items 3-5 for Steel Wheels
ns 008-290-17 1 Assy Hub 10 Stud 285.75mm ABS Includes Items 3-5 for Aluminum Wheels
ns 024-200-01 1 ABS Tone Ring Included with ABS hubs
3 031-026-01 1 Inner Bearing Cup (HM218210)
4 031-027-01 1 Outer Bearing Cup (HM212011)
5 007-194-00 10 Stud, Press-In M22 x 1.5 2.47" Stud Length for Steel Wheels
5 007-195-00 10 Stud, Press-In M22 x 1.5 3.32" Stud Length for Aluminum Wheels
6 009-043-03 1 Drum 16" x 7"
10 006-118-00 10 Swivel Flange Nut
11 071-124-00 1 Gasket - Oil Cap
12 021-038-02 1 Oil Cap (with vent plug)
13 005-100-00 6 Lock Washer - Oil Cap
14 007-157-00 6 Cap Screw Oil Cap
ns - not shown
1
6

"

X

7
"

B
R
A
K
E

S
I
Z
E
Hub & Drum Dimensional Information
Item Description Dimensions
A Cup to Cup 3.34"
B Cup to Mounting Face .73"
C Cup to End of Drum 9.87"
D Brake Diameter 16.50"
E Shoe Brake Width 7.00"
F Drum Overall Width 10.60"
G Pilot Diameter (Drum) 8.78"
H Bolt Circle 285.75mm (11.25")
I Bolt Diameter M22 x 1.5
J Hub Cap Hole Mtg "
6 Holes 5.50 BC
Inner Bearing Cup and Cone Overall Stack Thickness 1.575"
H
U
B
S

&

D
R
U
M
S
10
For use with 20" or 22.5" demountable rims
11
12
13
14
Item Part No. Qty Description
008-267-71 1 Wheel & Drum Assembly - Gunite 5763-1
008-267-72 1 Wheel & Drum Assembly - Webb 75209-GCA
008-267-76 1 Wheel & Drum Assembly - KIC 001-75207H
008-267-74 1 ABS Wheel & Drum Assembly - Gunite 5763-2
008-267-77 1 ABS Wheel & Drum Assembly - KIC 001-75207TH
11 071-124-00 1 Gasket - Oil Cap
12 021-038-02 1 Oil Cap (with vent plug)
13 005-100-00 6 Lock Washer - Oil Cap
14 007-157-00 6 Cap Screw - Oil Cap
Hub & Drum Dimensional Information
Item Description Dimensions
A Cup to Cup 3.34"
B Cup to Centerline Track 1.36" (w/4.00" spacer)
C Cup to End of Drum 9.90"
D Brake Diameter 16.50"
E Shoe Brake Width 7.00"
F Drum Overall Width 8.38"
G Pilot Diameter 9.44"
H Bolt Circle 11.00"
I Bolt Diameter "
J Hub Cap Hole Mtg "
6 Holes 5.50 BC
K Spacer 20" x 4"
Inner Bearing Cup and Cone Overall Stack Thickness 1.575"
Dimensions listed are referenced for Webb part only. Other cast wheel
suppliers dimensions may be slightly different. Check with supplier.
5Spoke Cast Wheels
1
6

"

X

7
"

B
R
A
K
E

S
I
Z
E
Wheel & Drum Assembly
H
U
B
S

&

D
R
U
M
S
11
Hubs & Drums; Wheels & Drums
Description Dexter Webb Erie Dayton Walther KIC Gunite
Assembly 8 on 275mm BC; Outboard 12" Brake* 008-396-70 20271CW4 n/a n/a 001-00133 n/a
Assembly 8 on 275mm BC; Outboard 12" Brake-ABS* 008-396-71 20271CW4T n/a n/a 001-00133T n/a
Assembly 8 on 275mm BC; Outboard 12" Brake
+
008-396-72 20271CW6 n/a n/a 001-00133L n/a
Assembly 8 on 275mm BC; Outboard 12" Brake-ABS
+
008-396-73 20271CW6T n/a n/a 001-00133LT n/a
Assembly 10 on 8" BC RH; Inboard 12" Brake* 008-277-70 10519CLMR n/a n/a 001-10511 n/a
Assembly 10 on 8" BC RH; Inboard 12" Brake-ABS* 008-277-28 10519CLMRT n/a n/a 001-10511T n/a
Assembly 10 on 8" BC LH; Inboard 12" Brake* 008-277-71 10519CLML n/a n/a 001-10512 n/a
Assembly 10 on 8" BC LH; Inboard 12" Brake-ABS* 008-277-29 10519CLMLT n/a n/a 001-10512T n/a
Assembly 15" 3-Spoke; 12" Brake 008-269-xx 70159CCA 950-2700-10 48-14054-054 001-70003H 5785-1
Assembly 15" 3-Spoke; 12" Brake-ABS 008-269-xx 70159CCAT80 950-2700-10-A 48-15613-056 001-70003TH 5785-2
Assy 10 on 11" BC RH; 9.44 Pilot Inboard 16" Brake* 008-279-70 10019 BE_R 704-2760 RH n/a n/a 5559-RH1
Assy 10 on 11" BC LH; 9.44 Pilot Inboard 16" Brake* 008-279-71 10019 BE_L 704-2760 LH n/a n/a 5559-LH1
Assy 10 on 11" BC RH; 8.78 Pilot Outboard 16" Brake* 008-290-79 20231UQ_R Call Erie
sales ofce
814-452-6431
for assistance.
n/a 001-00126 n/a
Assy 10 on 11" BC RH; 8.78 Pilot Outboard 16 Brake-ABS* 008-290-81 20231UQ_RT n/a 001-00126T n/a
Assy 10 on 11" BC LH; 8.78 Pilot Outboard 16 Brake* 008-290-80 20231UQ_L n/a 001-00127 n/a
Assy 10 on 11" BC LH; 8.78 Pilot Outboard 16" Brake-ABS* 008-290-82 20231UQ_LT n/a 001-00127T n/a
Assy 10 on 285.75mm BC; 8.78 Pilot Outboard 16" Brake* 008-290-32 Heavy Duty
20231UQ4
or Extra Hvy
20231UH4
706-2764-5
with 5324 Studs
for Steel Wheels
n/a Heavy Duty
001-00125
n/a
Assy 10 on 285.75mm BC; 8.78 Pilot Outboard 16" Brake-ABS* 008-290-33 Heavy Duty
20231UQ4T
or Extra Hvy
20231UH4T
706-2764-5-A
with 5424 Studs
for Steel Wheels
n/a Heavy Duty
001-0125T
n/a
Assy 10 on 285.75mm BC; 8.78 Pilot Outboard 16" Brake
+
008-290-34 Heavy Duty
20231UQ6
or Extra Hvy
20231UH6
706-2764-5-A
with 5322 Studs
for Aluminum
Wheels
n/a Heavy Duty
001-0125L
n/a
Assy 10 on 285.75mm BC; 8.78 Pilot Outboard 16" Brake-ABS
+
008-290-35 Heavy Duty
20231UQ6T
or Extra Hvy
20231UH6T
706-2764-5-A
with 5322 Studs
for Aluminum
Wheels
n/a Heavy Duty
001-0125LT
n/a
Assembly 20" 5-Spoke; 16" Brake 008-267-xx 75209GCA 904-2738-1 48-14018-051 001-75207H 5763-1
Assembly 20" 5-Spoke; 16" Brake-ABS 008-267-xx 75209GCAT 904-2738-1-A n/a 001-75207TH 5763-2
xx = See Hubs & Drums section for part number that varies with manufacturer.
The following listed part numbers have a drum pilot diameter of 8.53". These are obsolete and are available as service parts only, not to be
used for new construction. For new assemblies having 8.78" diameter drum pilot, see the above part numbers 008-290-79; -80; -81; -82.
Description Dexter Webb Erie Dayton Walther KIC Gunite
Assy 10 on 11" BC RH; 8.53 Pilot Outboard 16" Brake* 008-290-20 10209FRMR 705-2764 RH n/a n/a 5631-RH1
Assy 10 on 11" BC RH; 8.53 Pilot Outboard 16" Brake-ABS* 008-290-57 10209FRMRT 705-2764 RH-A n/a n/a n/a
Assy 10 on 11" BC LH; 8.53 Pilot Outboard 16" Brake* 008-290-21 10209FRML 705-2764 LH n/a n/a 5631-LH1
Assy 10 on 11" BC LH; 8.53 Pilot Outboard 16" Brake-ABS* 008-290-58 10209FRMLT 705-2764 LH-A n/a n/a n/a
Interchange Reference Information
The interchange reference information listed herein is based on the best available information at the time of publication and is to be used
as a guide only. Although every care has been taken in order to insure the accuracy of these interchanges, Dexter does not assume any
liability for errors, changes, omissions, or for harm resulting therefrom. It is recommended that all parts be thoroughly checked for proper
form, t, and function prior to installation and usage to determine interchangability.
* Steel Wheels
+
Aluminum Wheels
C
R
O
S
S

R
E
F
E
R
E
N
C
E
H
U
B
S

&

D
R
U
M
S
12
Bearings, Seals, and Caps
Type Description Dexter Part No.
Bearings
Inner Bearing Cone (HM218248) 031-026-02
Outer Bearing Cone (HM212049) 031-027-02
Oil Seal Unitized
National B-370025-BGR (Dexter standard) 010-055-01
Midland Mechanics Barrier 755400 010-055-02
Stemco Guardian 307-0743 010-055-03
Stemco 373-0143 Unitized 010-055-04
Dichtomatik OB4660099 010-055-09
Oil Cap
Stemco 343-4009 021-038-01
APT A-4010 021-038-02
Grease Cap 021-046-00
C
R
O
S
S

R
E
F
E
R
E
N
C
E
H
U
B
S

&

D
R
U
M
S
13
Anti-Lock Braking Systems (ABS)
March 1, 1998, the National Highway Trafc Safety Administration (NHTSA) passed a law that required all new
trailers with air actuated brakes to have anti-lock braking capability for any vehicle that falls under FMVSS121.
Dexters D200 series axles are offered with the ABS sensors (all 90 sensors) from the following ABS system
manufacturers:
Manufacturer Dexter PN Manufacturers PN
Haldex 097-003-00 36409001
Meritor - Wabco 097-007-00 441-032-808-0
It is recommended that the Electronic Control Unit (ECU) purchased for the trailer (not supplied by Dexter
Axle) be from the same manufacturer as the sensor.
Information about the various ECUs and other products offered by the manufacturers may be found by
contacting the manufacturer or one of their distributors:
Haldex
10707 NW Airworld Drive
Kansas City, MO 64153
Telephone: (816) 891-2470
Customer Service: (800) 643-2374
www.hbsna.com
Meritor - Wabco
2135 West Maple Road
Troy, MI 48084
Customer Service: (800) 535-5560
www.meritorwabco.com
H
U
B
S

&

D
R
U
M
S
14
Tires & Wheels
C
L
E
A
R
A
N
C
E
S

A
N
D

D
I
M
E
N
S
I
O
N
S
Spring Center for absolute maximum refer to calculation procedures.
(T 34.50" will satisfy most needs)
Disc Wheel Demountable
Maximum = T -32.50"
Minimum = T -34.50"
"
"
"
"
Ground
"
"
* Underslung
Using " seat height and 3 leaf 354-00 spring (standard Dexter HAP Kits)
** Overslung
T
I
R
E
S

&

W
H
E
E
L
S
15
Determining Maximum Spring Centers
for 22.5K 27.5K Axles
1. Typical over-the-road 96" wide semi-trailers with
leaf spring suspensions are equipped with axles
having 71" or 71 " axle track and either 38" or
39" spring centers. 102" wide trailers use axles
having 77" or 77" axle track and either 44" or
45" spring centers.
2. Axle track should be the widest possible with the
overall width of the outer dual tires not exceeding
the maximum trailer width of either 96" or 102"
as specied by law. Verify with State and Federal
laws for the type of roads the trailer is traveling.
3. Spring centers should be placed as wide
as possible to aid in resisting trailer rolling
movement - side-to-side sway. Maximum spring
center is governed by either the distance
between drums or the distance between the inner
dual tires of a given axle. Spring centers less than
the minimum specied will reduce axle carrying
capacity.
4. Begin by selecting appropriate dual tire capacity
and rim or wheel capacity to adequately haul the
load for which the trailer was designed.
Factor 1 - Distance between drums
A. Determine the hub group required to mate
with the tires, rims or wheels previously
selected.
B. From the hub group section of this catalog,
locate the proper hub & drum or wheel &
drum.
C. For Demountable Rims. Obtain the B and
C dimensions for your selected hub group in
this catalog, add them together, then multiply
by 2. Subtract this number from your track
dimension to obtain the dimension between
drums.
D. For Disc Wheels. Obtain the B and C
dimensions for your selected hub group in
this catalog. Next, determine the wheels
disc thickness at the mounting area. Add
these three gures together, then multiply
by 2. Subtract this number from your track
dimension to obtain the dimension between
drums.
Factor 2 - Distance between inner tires
5. Obtain the tire width dimension for the tires
previously selected. Dimensions shown in
this catalog may vary from manufacturer to
manufacturer. Check your tire manufacturers
latest tire catalog to be sure of the dimensions.
A. For Demountable Rims. From the previous
pages, obtain the W dimension (width of your
selected tire) and the Y dimension (dual rim
spacing of appropriate rims for your selected
tire) and add them together. Subtract this
number from your track dimension to obtain
the dimension between the inner dual tire set.
B. For Disc Wheels. From the previous pages,
obtain the W dimension (width of your
selected tire) and the Y dimension (dual
wheel spacing of appropriate wheels for your
selected tire) and add them together. Subtract
this number from your track dimension to
obtain the dimension between the inner dual
tire set.
6. Compare these two calculated numbers
Factor 1 and Factor 2 and select the smallest
(narrowest) of the two.
7. Subtract 2.75 from the above selected smallest
number. This should be your outside to outside
widest frame width for your given track. The
minimum frame clearance per side is 1.375, then
is multiplied by 2 to get 2.75.
8. Determine the width of your suspension system
hangers, typically 6.00 inches for H-9700 Hutch
suspension. If other than Hutch H-9700 are
used, determine the location of your selected
suspension systems hangers and where they
are to be positioned laterally on the trailer
frame member. Consult the manufacturer of
your suspension system if the location is not
detailed in their catalog. Determine the distance
from frame width to centerline of suspension
attachment to the axle beam tube relative to this
hanger position.
9. Subtract this number from outside frame width to
obtain the maximum spring center allowed.
A
P
P
L
I
C
A
T
I
O
N

I
N
F
O
R
M
A
T
I
O
N
T
I
R
E
S

&

W
H
E
E
L
S
16
Tires
A
P
P
L
I
C
A
T
I
O
N

I
N
F
O
R
M
A
T
I
O
N
Brake
Size
Tire Size
(Load Range)
Design
Rim
Width
**Dual Tire
Capacity
per Tire
(lbs.)
Max
Ination
P.S.I O.D.*
Tire
Width
W
Loaded
Section
Width
Z S.L.R.*
Min.
Dual
Spacing
Rim
Contour Description
Wheel/Rim
Capacity Each
(lbs.)
Max.
Ination
(P.S.I.)
Mtg.
Hole
Pattern
Wheel
Center Disc
Thickness
Offset
X
Dual
Spacing
Y
12" 10R17.5 (H) 6.75HC 4410 115 33.7 9.4 10.4 15.6 10.9 17.5 x 6.75 HC Rim 4805 125 Demountable
4" Spacer
n/a 3.90" 11.80"
12" 215/75R17.5 (H) 6.75HC 4540 125 30.6 8.4 9.3 14 9.6 17.5 x 6.75 HC Steel Wheel 5070 125 10 Hole
8.75" BC
6.50" Bore
Ball Seat
.42" 6.19" 12.38"
12" 235/75R17.5 (H) 6.75HC 5675 125 31.8 9.2 10.1 14.5 10.3 17.5 x 6.75 HC Steel Wheel 5355 125 8 Hole
275mm BC
221mm Bore
Pilot Mounting
.437" 5.60" 11.20"
12" 245/70R19.5 (G) 6.75 4375 100 33.0 10.2 11.0 15.3 11.0
19.5 x 6.75 RW Steel Wheel 5000 120
8 Hole
275mm BC
221mm Bore
Pilot Mounting
.437" 5.60" 11.2"
12" 265/70R19.5 (G) 6.75 5070 120 34.0 10.3 11.2 15.9 11.6
16" 255/70R22.5 (H) 7.50 5070 115 36.6 9.8 10.6 17.1 11.3 22.5 x 7.50 Steel Wheel 6610 120 10 Hole
11" BC
8.72" Bore
Ball Seat
.437" 6.44" 12.88"
16" 295/75R22.5 (G) 8.25 5675 100 40.2 11.2 12.2 18.8 11.2 22.5 x 8.25 Steel Wheel 7400 120 10 Hole
11 BC
8.72 Bore
Ball Seat
.437" 6.62" 13.25"
16" 11R22.5 (G) 8.25 5750 105 41.5 10.8 11.9 19.4 12.5
22.5 x 8.25 Steel Wheel 7400 120
10 Hole
285.75mm BC
220mm Bore
Pilot Mounting
.437" 6.62" 13.25"
16" 11R22.5 (H) 8.25 5800 110 41.5 10.8 11.9 19.4 12.5
16" 11R24.5 (G) 8.25 6000 105 43.5 10.8 11.9 20.4 12.5
24.5 x 8.25 Steel Wheel 7300 120
10 Hole
285.75mm BC
220mm Bore
Pilot Mounting
.437" 6.62" 13.25"
16" 11R24.5 (H) 8.25 6170 110 43.5 10.8 11.9 20.4 12.5
* Dimensions shown may vary slightly from manufacturer to manufacturer
** Dual Rating
T
I
R
E
S

&

W
H
E
E
L
S
17
Wheels & Rims
A
P
P
L
I
C
A
T
I
O
N

I
N
F
O
R
M
A
T
I
O
N
Brake
Size
Tire Size
(Load Range)
Design
Rim
Width
**Dual Tire
Capacity
per Tire
(lbs.)
Max
Ination
P.S.I O.D.*
Tire
Width
W
Loaded
Section
Width
Z S.L.R.*
Min.
Dual
Spacing
Rim
Contour Description
Wheel/Rim
Capacity Each
(lbs.)
Max.
Ination
(P.S.I.)
Mtg.
Hole
Pattern
Wheel
Center Disc
Thickness
Offset
X
Dual
Spacing
Y
12" 10R17.5 (H) 6.75HC 4410 115 33.7 9.4 10.4 15.6 10.9 17.5 x 6.75 HC Rim 4805 125 Demountable
4" Spacer
n/a 3.90" 11.80"
12" 215/75R17.5 (H) 6.75HC 4540 125 30.6 8.4 9.3 14 9.6 17.5 x 6.75 HC Steel Wheel 5070 125 10 Hole
8.75" BC
6.50" Bore
Ball Seat
.42" 6.19" 12.38"
12" 235/75R17.5 (H) 6.75HC 5675 125 31.8 9.2 10.1 14.5 10.3 17.5 x 6.75 HC Steel Wheel 5355 125 8 Hole
275mm BC
221mm Bore
Pilot Mounting
.437" 5.60" 11.20"
12" 245/70R19.5 (G) 6.75 4375 100 33.0 10.2 11.0 15.3 11.0
19.5 x 6.75 RW Steel Wheel 5000 120
8 Hole
275mm BC
221mm Bore
Pilot Mounting
.437" 5.60" 11.2"
12" 265/70R19.5 (G) 6.75 5070 120 34.0 10.3 11.2 15.9 11.6
16" 255/70R22.5 (H) 7.50 5070 115 36.6 9.8 10.6 17.1 11.3 22.5 x 7.50 Steel Wheel 6610 120 10 Hole
11" BC
8.72" Bore
Ball Seat
.437" 6.44" 12.88"
16" 295/75R22.5 (G) 8.25 5675 100 40.2 11.2 12.2 18.8 11.2 22.5 x 8.25 Steel Wheel 7400 120 10 Hole
11 BC
8.72 Bore
Ball Seat
.437" 6.62" 13.25"
16" 11R22.5 (G) 8.25 5750 105 41.5 10.8 11.9 19.4 12.5
22.5 x 8.25 Steel Wheel 7400 120
10 Hole
285.75mm BC
220mm Bore
Pilot Mounting
.437" 6.62" 13.25"
16" 11R22.5 (H) 8.25 5800 110 41.5 10.8 11.9 19.4 12.5
16" 11R24.5 (G) 8.25 6000 105 43.5 10.8 11.9 20.4 12.5
24.5 x 8.25 Steel Wheel 7300 120
10 Hole
285.75mm BC
220mm Bore
Pilot Mounting
.437" 6.62" 13.25"
16" 11R24.5 (H) 8.25 6170 110 43.5 10.8 11.9 20.4 12.5
* Dimensions shown may vary slightly from manufacturer to manufacturer
** Dual Rating
T
I
R
E
S

&

W
H
E
E
L
S
18
Axle/Brake Components
PQ Style
Brake Shoe Hardware Kit K71-460-00
Fits PQ style Dexter 10-27K 12" air brake axles.
For one brake.
DX Part No. Quantity Part Description
005-076-00 2 Washer
014-057-00 2 Roller
014-068-00 2 Bushing
046-092-00 1 Retractor Spring
046-097-00 2 Shoe Keeper Spring
056-010-00 2 Roller Pin
056-017-00 2 Anchor Pin
056-018-00 2 Retainer Pin
069-018-00 2 Snap Ring for .750 Shaft
059-553-00 1 Instruction Sheet
Camshaft Repair Kit K71-101-00
Fits P and PQ style Dexter 10K, 12K, 15K, and
12" x 7" air brake axles. For one brake.
DX Part No. Quantity Part Description
005-074-00 1 D Washer Camshaft
005-075-00 2 Camshaft Washer
005-134-00 1 Plain Washer
010-052-00 2 Seal
014-056-00 1 Camshaft Bushing
014-058-00 1 Camshaft Support Bushing
061-006-00 1 Grease Fitting
069-020-00 2 Camshaft Retainer
069-078-00 1 Snap Ring
059-663-00 1 Instruction Sheet
Brake Block Kit K71-133-00
For one Dexter 12"x 7" brake.
DX Part No. Quantity Part Description
022-018-00 48 Rivet
041-057-01 2 Brake Block
041-060-01 2 Brake Block
059-191-00 1 Instruction sheet
ns - not shown
Axle beams are produced using the latest in friction welding technology.
1
2

"

X

7

"

B
R
A
K
E

S
I
Z
E
A
X
L
E
/
B
R
A
K
E

C
O
M
P
O
N
E
N
T
S
19
PQ Style
Axle/Brake Components
Item Part No. Qty per Axle Description Comments
1A D-2L12
D-2M12
D-2H12
1
1
1
Beam Options
Beam Options
Beam Options
Light Wall 22,500# Rating
Medium Wall 25,000# Rating; with Air Ride 22,500#
Heavy Wall, 27,500# Rating; with Air Ride 25,000#
1B* 036-114-02 2 Spider (using anchor pin bushing) Weld on (includes #2)
1C 034-031-00 2 Bracket - Camshaft Support Weld-on
1C1 034-032-00 4 Retainer Plate
1C3 007-139-00 8 Bolt - Retainer Plate Attachment
1C4 005-079-00 8 Lock Washer - Cover Attachment
1C5 006-099-00 8 Nut - Retainer Plate Attachment
1D 034-048-00 2 Bracket - Air chamber Mounting Weld-on Standard
2 014-068-00 4 Bushing - Spider Anchor Pin
3 056-017-00 4 Anchor Pin
4 040-320-01 4 Shoe and Lining Assembly Friction Code FF
4A 041-060-01 4 Lining - Brake Block Cam (FMSI 4591 D)
4B 041-057-01 4 Lining - Brake Block Anchor (FMSI 4591 D)
5 014-057-00 4 Roller
6 056-010-00 4 Retainer - Roller Pin
6A 069-018-00 4 Retainer Ring
7 046-092-00 2 Spring - Shoe Retractor Blue color
8 056-018-00 4 Retainer Pin - Retractor Spring
9 046-097-00 4 Spring - Shoe Keeper Orange Color
10 005-074-00 2 D Washer - Camshaft .06 thick
11 010-052-00 4 Grease Seal
12 014-056-00 2 Bushing - Camshaft Spider Nylon
13 005-075-00 1 Washer
13A 005-134-00 2 Washer - Camshaft Slack Adjuster End For 28-spline Camshafts only
14 069-020-00 2 Snap Ring
14A 069-078-00 2 Retainer - Camshaft Slack Adjuster End For 28-spline Camshafts only
15 014-058-00 2 Bushing - Camshaft Support Nylon
16 034-xxx-xx 2 Camshaft LH/RH See Camshaft section for options
ns 055-039-00 2 Slack Adjuster - Manual 1.46 x 28-spline
17 055-040-99 2 Slack Adjuster Angled Automatic
1.46 x 28-spline 6" arm
Boxed kit includes clevis, pins, gage,
and instructions
18 006-114-00 2 Nut - Inner Spindle Bearing
19 005-098-00 2 Lock Washer - Indexing
20 005-099-00 2 Lock Washer - Tab
21 006-115-00 2 Nut - Outer Spindle
22 061-006-00 2 Grease Fitting 65
23A 034-xxx-xx 2 Air Chamber Assembly (includes item 23E, 23F) See Air Chamber section for options
ns 055-057-00 2 Clevis for manual slacks only Clevis, Clevis Pin & Cotter Pin
for Manual Slacks
23E 4 Lock Washer - Air chamber Mounting
(included in item 23A)
23F 4 Nut - Air Chamber Mounting (included in item 23A)
24 024-100-00 2 Sensor block
26 097-002-00 2 Retainer Clip
27 097-003-00
097-007-00
2
2
ABS Sensor, 90
ABS Sensor, 90
Haldex
Meritor - Wabco
* Not for individual resale
xx - See Camshaft section for part number that varies by length
1
2

"

X

7

"

B
R
A
K
E

S
I
Z
E
A
X
L
E
/
B
R
A
K
E

C
O
M
P
O
N
E
N
T
S
20
Axle/Brake Components
Q Style
Brake Shoe Hardware Kit K71-136-00
Fits Q quick change Dexter 16" x 7" air brake
axles. For one brake.
DX Part No. Quantity Part Description
014-065-00 2 Roller
014-068-00 2 Spider Bushing
046-096-00 1 Retractor Spring 16" Brake-Orange
046-097-00 2 Keeper Spring
056-017-00 2 Anchor Pin
056-018-00 2 Spring Retainer
071-122-00 2 Roller Retainer
059-554-00 1 Instruction Sheet
Camshaft Repair Kit K71-135-00
Fits all Q quick change Dexter 16" x 7" air brake
axles. For one brake.
DX Part No. Quantity Part Description
005-096-00 1 Camshaft Washer
005-097-00 2 Camshaft Washer
005-134-00 1 Plain Washer
010-052-00 2 Seal
014-056-00 1 Camshaft Bushing
014-058-00 1 Camshaft Support Bushing
061-006-00 1 Grease Fitting
069-020-00 2 Camshaft Retainer
069-078-00 1 Snap Ring
059-554-00 1 Instruction Sheet
Brake Block Kit K71-138-00
For one Dexter 16"x 7" air brake.
DX Part No. Quantity Part Description
022-018-00 48 Rivet
041-058-01 2 Brake Block
041-059-01 2 Brake Block
059-191-00 1 Instruction sheet
ns - not shown
Axle beams are produced using the latest in friction welding technology.
1
6

"

X

7
"

B
R
A
K
E

S
I
Z
E
A
X
L
E
/
B
R
A
K
E

C
O
M
P
O
N
E
N
T
S
21
Q Style
Axle/Brake Components
Item Part No. Qty per Axle Description Comments
1A D-2L16
D-2M16
D-2H16
1
1
1
Beam Options
Beam Options
Beam Options
Light Wall 22,500# Rating
Medium Wall 25,000# Rating; with Air Ride 22,500#
Heavy Wall, 27,500# Rating; with Air Ride 25,000#
1B* 036-092-02 2 Spider Weld on (includes #2)
1C 034-047-04 2 Bracket - Camshaft Support Weld-on
1C2 034-032-00 4 Retainer Plate
1C3 007-139-00 8 Bolt - Retainer Plate Attachment
1C4 005-079-00 8 Lock Washer - Cover Attachment
1C5 006-099-00 8 Nut - Retainer Plate Attachment
1D 034-048-00 2 Bracket - Air chamber Mounting Weld-on Standard
2 014-068-00 4 Bushing - Spider Anchor Pin
3 056-017-00 4 Anchor Pin
4 040-180-00 4 Shoe and Lining Assembly Friction Code FF
4A 041-058-01 4 Lining - Brake Block Cam (FMSI 4515 D)
4B 041-059-01 4 Lining - Brake Block Anchor (FMSI 4515 D)
5 014-065-00 4 Roller
6 071-122-00 4 Retainer - Roller
7 046-096-00 2 Spring - Shoe Retractor Orange Color
8 056-018-00 4 Retainer Pin - Retractor Spring
9 046-097-00 4 Spring - Shoe Keeper Orange Color
10 005-096-00 2 Washer - Camshaft .120 thick
11 010-052-00 4 Grease Seal
12 014-056-00 2 Bushing - Camshaft Spider Nylon
13 005-097-00 2 Washer
13A 005-134-00 2 Washer - Camshaft Slack Adjuster End For 28-spline Camshafts only
14 069-020-00 2 Snap Ring
14A 069-078-00 2 Retainer - Camshaft Slack Adjuster End For 28-spline Camshafts only
15 014-058-00 2 Bushing - Camshaft Support Nylon
16 034-xxx-xx 2 Camshaft LH/RH See Camshaft section for options
ns 055-039-00 2 Slack Adjuster - Manual 1.46 x 28-spline
17 055-040-98 2 Slack Adjuster Straight Automatic
1.46 x 28-spline 6" arm
Boxed kit includes clevis, pins, gage,
and instructions
18 006-114-00 2 Nut - Inner Spindle Bearing
19 005-098-00 2 Lock Washer - Indexing
20 005-099-00 2 Lock Washer - Tab
21 006-115-00 2 Nut - Outer Spindle
22 061-006-00 2 Grease Fitting 65
23A 034-xxx-xx 2 Air chamber Assembly (includes item 23E, 23F) See Air Chamber section for options
ns 055-057-00 2 Clevis for manual slacks only Clevis, Clevis Pin & Cotter Pin
for Manual Slacks
23E 4 Lock Washer - Air chamber Mounting
(included in item 23A)
23F 4 Nut - Air Chamber Mounting (included in item 23A)
24 024-100-00 2 Sensor block
25 097-002-00 2 Retainer Clip
26 097-003-00
097-007-00
2
2
ABS Sensor, 90
ABS Sensor, 90
Haldex
Meritor - Wabco
* Not for individual resale
xx - See Camshaft section for part number that varies by length
1
6

"

X

7
"

B
R
A
K
E

S
I
Z
E
A
X
L
E
/
B
R
A
K
E

C
O
M
P
O
N
E
N
T
S
22
Tandem Air System
Two Reservoir Two Valve System
Note: This schematic is for reference only. If your system is congured
differently or you have a different suppliers part numbers,
consult with the authorized supplier for proper use, location and
installation of your components.
T
A
N
D
E
M

A
I
R

S
Y
S
T
E
M
23
S Head Camshafts
1
2

"

X

7

"

B
R
A
K
E

S
I
Z
E
Small S Head Hi-Rise
28 Spline
Part Number A B C
LH RH
034-188-00 034-189-00 21.125 2.219 For 1.50 diameter shaft*
034-188-01 034-189-01 16.375 2.219 For 1.50 diameter shaft*
034-188-03 034-189-03 22.312 2.219 For 1.50 diameter shaft*
034-188-04 034-189-04 20.312 2.219 For 1.50 diameter shaft
034-188-05 034-189-05 23.375 2.219 For 1.50 diameter shaft
034-188-06 034-189-06 30.000 2.219 For 1.50 diameter shaft
034-188-07 034-189-07 29.000 2.219 For 1.50 diameter shaft
034-188-08 034-189-08 19.500 2.219 For 1.50 diameter shaft
034-188-09 034-189-09 26.500 2.219 For 1.50 diameter shaft
034-188-10 034-189-10 7.437 2.219 For 1.50 diameter shaft
034-188-11 034-189-11 24.625 2.219 For 1.50 diameter shaft
* No extra charge for these lengths
3
3
/32
Viewed from head end
29
/32
C
A
M
S
H
A
F
T
S
24
S Head Camshafts
1
6

"

X

7
"

B
R
A
K
E

S
I
Z
E
Large S Head Hi-Rise
28 Spline
Part Number A B C
LH RH
034-192-00 034-193-00 16.625 2.219 For 1.50 diameter shaft*
034-192-01 034-193-01 20.375 2.219 For 1.50 diameter shaft
034-192-02 034-193-02 30.000 2.219 For 1.50 diameter shaft
034-192-03 034-193-03 23.438 2.219 For 1.50 diameter shaft*
034-192-04 034-193-04 26.500 2.219 For 1.50 diameter shaft
034-192-05 034-193-05 22.625 2.219 For 1.50 diameter shaft
034-192-06 034-193-06 19.500 2.219 For 1.50 diameter shaft
034-192-07 034-193-07 29.000 2.219 For 1.50 diameter shaft
034-192-08 034-193-08 25.000 2.219 For 1.50 diameter shaft
034-192-09 034-193-09 28.000 2.219 For 1.50 diameter shaft
034-192-10 034-193-10 24.375 2.219 For 1.50 diameter shaft
034-192-11 034-193-11 7.438 2.219 For 1.50 diameter shaft
* No extra charge for these lengths
4
1
/4
Viewed from head end
1
3
/16
C
A
M
S
H
A
F
T
S
25
Service Air Chambers
Part Number Size A B C D E F G Recommended Application
034-260-07 Type 20 5.62 7.00 1.25 -11 -18 4.75 .50 12" Brake with Tramec Angled Automatic Slack
034-260-08 Type 20 6.38 7.00 1.25 -11 -18 4.75 .50 12 Brake with Straight Manual Slack
034-059-01 Type 24 7.00 7.50 1.25 -11 -18 4.75 .50 Optional 16" Brake with Tramec Angled Automatic Slack
034-059-07 Type 24 5.62 7.50 1.25 -11 -18 4.75 .50 12 Brake with Tramec Angled Automatic Slack
034-059-08 Type 24 6.38 7.50 1.25 -11 -18 4.75 .50 12 Brake with Straight Manual Slack
034-057-01 Type 30 7.00 8.50 1.25 -11 -18 4.75 .50 Standard 16 Brake
034-057-07 Type 30 5.62 8.50 1.25 -11 -18 4.75 .50 12 Brake with Tramec Angled Automatic Slack
034-057-08 Type 30 6.38 8.50 1.25 -11 -18 4.75 .50 12 Brake with Straight Manual Slack
Note: Clevis assembly NOT included with air chamber. See brake section for Clevis kits.
A
I
R

C
H
A
M
B
E
R
S
26
Spring Brake Air Chambers
Part Number Size A B C D E F G Recommended Application
034-261-07 Type 20-24 5.62 7.53 1.25 -11 -18 4.75 .50 12" Brake with Tramec Angled Automatic Slack
034-261-08 Type 20-24 6.38 7.53 1.25 -11 -18 4.75 .50 12" Brake with Straight Manual Slack
034-060-01 Type 24-30 7.00 7.50 1.25 -11 -18 4.75 .50 Optional 16" Brake with Tramec Angled Automatic Slack
034-060-07 Type 24-30 5.62 7.50 1.25 -11 -18 4.75 .50 12" Brake with Tramec Angled Automatic Slack
034-060-08 Type 24-30 6.38 7.50 1.25 -11 -18 4.75 .50 12" Brake with Straight Manual Slack
034-058-01 Type 30-30 7.00 8.50 1.25 -11 -18 4.75 .50 Standard 16" Brake
034-058-07 Type 30-30 5.62 8.50 1.25 -11 -18 4.75 .50 12" Brake with Tramec Angled Automatic Slack
034-058-08 Type 30-30 6.38 8.50 1.25 -11 -18 4.75 .50 12" Brake with Straight Manual Slack
Note: Clevis assembly NOT included with air chamber. See brake section for Clevis kits.
A
I
R

C
H
A
M
B
E
R
S
27
Tandem Axle Congurations
Off-Road Applications
Note:
1. Position of air chambers as shown results in optimum clearances.
2. Use of equal length service lines is recommended.
3. To assure welds are within approved neutral axis zone quadrants, maximum rotation of camshaft position
is +6 up to -6 down from 0 neutral axis.
A
I
R

C
H
A
M
B
E
R
S
28
Tandem Axle Congurations
Over-the-Highway Applications
Note:
1. Position of air chambers as shown results in optimum clearances.
2. Use of equal length service lines is recommended.
3. To assure welds are within approved neutral axis zone quadrants, maximum rotation of camshaft position
is +6 up to -6 down from 0 neutral axis.
A
I
R

C
H
A
M
B
E
R
S
29
H-9700 Underslung
Suspension Kits
Order appropriate number of HAP kits and
springs for a complete suspension kit
H-9700 Underslung Dexter Spring
HAP-101-00 HAP-201-00 072-048-00
Qty for Single 1 n/a 2
Qty for Tandem 1 1 4
Qty for Triple 1 2 6
6 1/2 38
7
3
7
12
14
16
13
11
9
8
1
10
3 7/8
Mtg. Ht.
19 Ref.
Front
6 1/2 43 1/2
49
7
Mtg. Ht.
43 1/2 3 7/8
1
17
9
4
5
6
8
3
2,2a,2b,2c,2d,2e
19 Ref.
6 1/2 43 1/2 49 3/4 43 1/2
19 Ref.
7
Mtg. Ht.
3 7/8
1
9
9
6
5
4
8
3
2,2a,2b,2c,2d,2e
49 49 3/4
Item Description HAP-101-00 HAP-201-00 Comments
1 Front Hanger 2 n/a
2 Hanger & Equalizer Assembly n/a 2
2a Hanger n/a 2
2b Equalizer Assembly w/rubber bushing n/a 2
2c Hex Cap Screw n/a 2 1"-7 UNC x 6" GR5
2d Washer n/a 4 " x 1" ID x 2" OD
2e Hex Locknut n/a 2 1"-7 UNC GR5
3 Rear Hanger 2 n/a Complete w/bolt spacer & nut
4 Sleeve Spacer n/a 4
5 Hex Nut " n/a 4
6 Hex Bolt " n/a 4
7 Bottom Plate 2 2
8 Torque Arm - Adjustable 1 1
9 Torque Arm - Non-Adjustable 1 1
10 Torque Arm Bolt 4 4
11 Locknut Flanged 4 4
12 Washer " Flat 8 8
13 Hex Nut " 8 8
14 U-Bolt 11" Length 4 4
15 Spring 3-Leaf Standard 2 2 Dexter part number 072-048-00 sold separately
16 Spring Seat " High 2 2
ns Galvanized Liner 2 2
Note: Mounting height shown above is in the unloaded condition.
S
U
S
P
E
N
S
I
O
N
S
30
H-9700 Overslung
Suspension Kits
Order appropriate number of HAP kits and
springs for a complete suspension kit
H-9700 Overslung Dexter Spring
HAP-102-00 HAP-202-00 072-048-00
Qty for Single 1 n/a 2
Qty for Tandem 1 1 4
Qty for Triple 1 2 6
6 1/2 38
16
3
15
14
16 13
11
9
8
1
10
3 7/8
Mtg. Ht.
19 Ref.
Front
6 1/2 43 1/2
49
16
Mtg. Ht.
43 1/2 3 7/8
1
17
9
4
5
6
8
12
7
3
2,2a,2b,2c,2d,2e
19 Ref.
6 1/2 43 1/2 49 3/4 43 1/2
19 Ref.
16
Mtg. Ht.
3 7/8
1
9
9
8
3
2,2a,2b,2c,2d,2e
49 49 3/4
Item Description HAP-102-00 HAP-202-00 Comments
1 Front Hanger 2 n/a
2 Hanger & Equalizer Assembly n/a 2
2a Hanger n/a 2
2b Equalizer Assembly w/rubber bushing n/a 2
2c Hex Cap Screw n/a 2 1"-7 UNC x 6" GR5
2d Washer n/a 4 " x 1" ID x 2" OD
2e Hex Locknut n/a 2 1"-7 UNC GR5
3 Rear Hanger 2 n/a Complete w/bolt spacer & nut
4 Sleeve Spacer n/a 4
5 Hex Nut " n/a 4
6 Hex Bolt " n/a 4
7 Top Plate 2 2
8 Torque Arm - Adjustable 1 1
9 Torque Arm - Non-Adjustable 1 1
10 Torque Arm Bolt 4 4
11 Locknut Flanged 4 4
12 Spring Seat " High 2 2
13 Bottom Plate 5" Round 2 2
14 Washer " Flat 8 8
15 Hex Nut " 8 8
16 U-Bolt 10 " Length 4 4
17 Spring 3-Leaf Standard 2 2 Dexter part number 072-048-00 sold separately
ns Galvanized Liner 2 2
Note: Mounting height shown above is in the unloaded condition.
S
U
S
P
E
N
S
I
O
N
S
31
Dexter Axle Limited Warranty
WHAT PRODUCTS ARE COVERED
All Dexter Axle Company (Dexter Axle) trailer axles,
suspensions, and brake control systems excluding Dexter
6000 series Manufactured Housing Axles.
LIMITED 2 YEAR WARRANTY
Dexter Axle warrants to the original purchaser that its axles,
suspension systems, and E/H hydraulic brake actuators
shall be free from defects in material and workmanship for
a period of two (2) years from the date of rst sale of the
trailer incorporating such components.
LIMITED 5 YEAR WARRANTY
Dexter Axle warrants to the original purchaser that its
Nev-R-Lube

bearings and the suspension components

only, of its Torex

Axles shall be free from defects in

material and workmanship for a period of ve (5) years
from the date of rst sale of the trailer incorporating such
components.
LIMITED 7 YEAR WARRANTY
Dexter Axle warrants to the original purchaser that its
Predator Series

electric brake controllers shall be free from

defects in material and workmanship for a period of seven
(7) years from the date of purchase.
EXCLUSIVE REMEDY
Dexter Axle will, at its option, repair or replace the affected
components of any defective axle, repair or replace the
entire defective axle, or refund the then-current list price
of the axle. In all cases, a reasonable time period must be
allowed for warranty repairs to be completed. Allowance will
only be made for installation costs specically approved by
Dexter Axle.
WHAT YOU MUST DO
In order to make a claim under these warranties:
1. You must be the original purchaser of the vehicle in
which the spring suspension axles or Torex

axles were
originally installed.
2. You must promptly notify us within the warranty period
of any defect, and provide us with the axle serial number
and any substantiation which may include, but is not
limited to, the return of part(s) that we may reasonably
request.
3. The axles or suspensions must have been installed
and maintained in accordance with good industry
practice and any specic Dexter Axle recommendations,
including those specied in Dexter Axles publication
Operation Maintenance Service Manual.
EXCLUSIONS
These warranties do not extend to or do not cover defects
caused by:
1. The connecting of brake wiring to the trailer wiring or
trailer wiring to the towing vehicle wiring.
2. The attachment of the running gear to the frame.
3. Hub imbalance, or any damage caused thereby.
4. Parts not supplied by Dexter Axle.
5. Any damage whatever caused by or related to any
alteration of the axle including welding supplemental
brackets to the axle.
6. Use of an axle on a unit other than the unit to which it
was originally mounted.
7. Normal wear and tear.
8. Alignment.
9. Improper installation.
10. Unreasonable use (including failure to provide
reasonable and necessary maintenance as specied
in Dexter Axles publication Operation Maintenance
Service Manual including required maintenance after
Prolonged Storage).
11. Improper wheel nut torque.
12. Cosmetic nish or corrosion.
LIMITATIONS
1. In all cases, Dexter Axle reserves the right to fully
satisfy its obligations under the Limited Warranties
by refunding the then-current list price of the
defective axle (or, if the axle has been discontinued,
of the most nearly comparable current product).
2. Dexter Axle reserves the right to furnish a substitute
or replacement component or product in the event an
axle or any component of the axle is discontinued or is
otherwise unavailable.
3. These warranties are nontransferable.
GENERAL
THE FOREGOING WARRANTIES ARE EXCLUSIVE AND
IN LIEU OF ALL OTHER WARRANTIES EXCEPT THAT
OF TITLE, WHETHER WRITTEN, ORAL OR IMPLIED, IN
FACT OR IN LAW (INCLUDING ANY WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE).
These warranties give you specic legal rights, and you
may also have other rights which vary from state to state.
DEXTER AXLE HEREBY EXCLUDES INCIDENTAL AND
CONSEQUENTIAL DAMAGES, INCLUDING LOSS OF
TIME, INCONVENIENCE, LOSS OF USE, TOWING FEES,
TELEPHONE CALLS OR COST OF MEALS, FOR ANY
BREACH OF ANY EXPRESS OR IMPLIED WARRANTY.
Some states do not allow limitations on how long an implied
warranty lasts, or the exclusion or limitation of incidental
or consequential damages, so the above exclusion or
limitation may not apply to you.
Inquiries regarding these warranties should be sent to:
Dexter Axle Company
P.O. Box 250
Elkhart, Indiana 46515
32
Notes
Genuine Dexter axles and components are available
nationwide from our plant locations listed below or
through our network of distributors. Check our web site
for the distributor nearest you.
Visit us online at www.dexteraxle.com
Dexter Axle
301 West Pearl Street
Fremont, IN 46737
Fax (260) 495-1701
Ph (260) 495-5100
Dexter Axle
199 Perimeter Road
Monticello, GA 31064
Fax (706) 468-2966
Ph (706) 468-6495
Dexter Axle
500 Southeast 27th Street
El Reno, OK 73036
Fax (405) 262-9089
Ph (405) 262-6700
Dexter Axle
500 South 7th Street
Albion, IN 46701
Fax (260) 636-3030
Ph (260) 636-2195
Company Headquarters
2900 Industrial Parkway East
Elkhart, IN 46516
Fax (574) 295-8666
Ph (574) 295-7888
NO PART OF THIS CATALOG MAY BE REPRODUCED WITHOUT DEXTER AXLES PERMISSION.
ALL PART NUMBERS, DIMENSIONS AND SPECIFICATIONS IN THIS CATALOG ARE SUBJECT
TO CHANGE WITHOUT NOTICE.
22,500 - 27,500 LBS. CAPACITY
HEAVY DUTY D200 SERIES
www.dexteraxle.com
GEARED FOR INNOVATION SINCE 1960
2900 Industrial Parkway East n Elkhart, IN 46516
Phone: 574-295-7888 n Fax: 574-295-8666
1/11 2011 Dexter Axle Company. LIT-121-00
www.dexteraxle.com