CTB technology

Distributor

BEIJING CTB TECHNOLOGY CO., LTD.

Address: Wanggezhuang Industry Base, Shilipu Town, Miyun County,
Beijing
Tel.: 010 -82755611
Fax: 010 -82755610
24-hour national free service Tel.:400 -888-9055
Data No.: ZL-12-808-IBCN
The data may subject to change without notice as improvement of the
product.


CTB technology

GS DRIVER
P100 operating manual
AC servo spindle driver
Model: BKSC- GS
Class 400V, 1.5 ~ 315KW (2.5 ~ 460KVA)
Please send the manual to final user, and keep it properly.

BEIJING CTB TECHNOLOGY CO.,LTD.

Data No.: Z L-12-808-I B C N

GS DRIVER

CTB
Preface

Thank you for purchasing GS series servo driver produced by Beijing CTB Technology Co.,
Ltd. The GS series AC servo spindle driver is a high-quality, multi-functional and low-noise
AC servo driver that was researched, developed and manufactured by Beijing CTB
Technology Co., Ltd. The spindle driver is servo driver for AC induction motor (IM) and AC
permanent magnet synchronous motor (PM). It can control the position, speed,
acceleration and output torque of various AC servo spindle motor appropriately. The wide
application of GS series AC servo spindle driver brings infinite vitality to field of machine
tool spindle drive control.
In command to achieve control functions of various machine tools, GS series AC servo
spindle driver is equipped with dual 32-bit CPU and abundant control function module. It
may be conveniently connected with various domestic and foreign CNC systems through
standard control interfaces to allow full play to spindle function of CNC system. The
characteristics of torque, acceleration and deceleration, precision and efficiency of machine
tool spindle which is equipped with GS series AC servo spindle driver are remarkable, and
accurate stop, C-axis, rigid tapping, electronic shift, multi-axis synchronization and other
spindle functions can be realized easily. GS series AC servo spindle driver is the first
choice of electric spindle drive products.
As the first choice of driving product of various machine tool power shaft (spindle), GS
series AC servo spindle driver can be widely used for spindle drive of product such as CNC
milling machine, vertical machining center, horizontal machining center, CNC boring
machine, CNC lathe, vertical lathe, heavy horizontal lathe and gantry machine tool.
For proper application, please read the manual carefully before using the GS series AC
servo spindle driver. Abnormal operation, fault or reduction of service life, and even
personal injury accident may be caused by inappropriate use. Therefore, the manual shall
be read repeatedly before use, and operate in strict accordance with the instructions. The
manual is attachment with the equipment. Please keep it properly after using for future
repair and maintenance of the driver.

01

GS DRIVER

CTB

Safety -related symbol description

The following symbols are used for safety-related content in the manual. Sentences
marked by the safety symbols describes important content, and must be abided. If the
requirements in the safety-related content are not abided, application of the product may
led to abnormal product operation, damage to the product, even danger and personal
injury.

02

Danger

Use the symbol where danger, even personal injury or death when
wrong about the described content.

Caution

Use the symbol where danger, even mild or moderate personal

injury and equipment damage when wrong about the described
content.

Forbid

Prohibited matters (matters that cannot do).

Important

Certain matters do not belong to "danger", and "caution", but they

are required to be abided by user. They are marked in the relevant
sections.

GS DRIVER

CTB

Safety precautions
Unpacking inspection
Caution
For risk of injury, please do not install damaged or part missing driver.
Installation
Caution
For risk of fire, please install the equipment on nonflammable metal plate without
combustible materials around.
Please be sure to tighten the mounting screws of the driver. Falling and damage of the
driver or personal injury may be caused by mounting screws loosing.
Please do not install the equipment in environment with flammable gas where an
explosion is caused easily.
Wiring

Danger
For risk of electric shock and fire, please make sure that the input power supply is in
the OFF state before wiring.
For risk of electric shock, the operation on main circuit terminal of the controller shall be
conducted after the power is cut off for five minutes, and the power charge indicator
CHARGE in the controller completely extinguished.
For risk of electric shock and fire, the wiring shall be carried by professional electrical
engineering personnel.
For risk of electric shock and fire, the ground terminal must be grounded reliably. (earth
resistance shall be lower than 4)
It's prohibited to directly connect terminals of P / PB and N, or connect the zero line or
the earth wire to the N terminal. Otherwise, the rectifier bridge will be shorted and the
main loop will be burned.
It's prohibited to connect the high-voltage line to control terminal of the driver.
Otherwise, the control board will be burned.
For risk of injury, please set emergency stop and locking circuit at the outside of the
controller (user is responsible for the wiring) .
There is a risk of electric shock and short circuit.

03

GS DRIVER

CTB

Wiring
Caution
For risk of injury and fire, please ensure that the voltage of the main circuit AC input
power and the rated voltage of the driver are consistent.
Please do not conduct withstand voltage and insulation test to the controller
arbitrarily. Otherwise, the semiconductor and other components in the controller may
be damaged.
For risk of fire, please connect braking resistor and braking unit according to the
wiring diagram.
Please do not connect the AC input power cord to the output U, V, W terminals.
Otherwise, damage to inside of the controller may be caused.
For risk of fire and malfunction of the controller, please tighten the terminals of main
loop and control circuit with appropriate torque.
Please do not connect the phase shifting electrolytic capacitor and LC / RC noise
filter to the output circuit. Otherwise, damage to inside of the controller may be
caused.
Please do not connect the electromagnetic switch and electromagnetic contactor to
the output circuit to connect or disconnect the load. During loaded operation of the
controller, the surge current will arose protection circuit action of the controller.
Trial run
Danger
For risk of electric shock and short circuit, please do not touch the terminals of the
main circuit directly after power-on.
Please confirm the input and output signals to guarantee safe operation.
Malfunction of the system will cause casualties and damage to the work piece and
nearby equipment..
For risk of injury, alarm reset only can be done after ensuring that the operating
signal is cut off. Alarm reset with operating signal will lead to suddenly re-start.
For risk of driver burning, the inside of long term stored driver shall be checked for
water and condensation.
For risk of electric shock and burning the equipment, it's prohibited to touch the
terminals of the driver with hand during operating.
04

GS DRIVER

CTB
Caution

For risk of scalding, the running servo driver and motor may have a high
temperature rise, please do not touch.
For risk of scalding and electric shock as the braking resistor has a high
temperature rise for discharging, please do not touch.
For risk of damage to the equipment and accident, please do not change the
settings of the drive arbitrarily.

05

GS DRIVER

CTB

Maintenance and inspection

Danger
For risk of electric shock, please do not directly touch terminals of the controller.
Some of them have high voltage and very dangerous.
For risk of electric shock, please do install the housing before power-on; and must
disconnect the power firstly before removing the housing.
For risk of electric shock and fire, please confirm that the power source is in the OFF
state or not before wiring.
Inspection and maintenance only can be carried out after cut off the main circuit input
power and confirm that the power charge indicator CHARGE completely extinguished.
There is a risk of electric shock as residual power in electrolytic capacitor.
Please make designated professional electrical engineering personnel to conduct
inspection and maintenance. Before work, please take off metal object (watch, rings
etc.), and use tools with insulation protection during operation. Otherwise, it may cause
electric shock.
For risk of explosion and fire, used battery, circuit printing plate must not be throw into
fire. Otherwise, it may cause explosion.

Caution
CMOS IC integrated circuit is installed on main control panel. Full attention shall be
paid during operating. The electrostatic induction due to direct touching of finger on the
main control panel may cause damage to the main control panel.
For risk of electric shock, please do not conduct wiring and removing terminal when
the equipment is energized.
For risk of damage to the equipment, the appropriate parameter settings must be
carried out before running after control panel replacing.

06

GS DRIVER

CTB
Table of contents

Preface1
Safety -related symbol description..2
Safety precautions....3
Chapter 1 - Installation..1-1
Introduction to GS DRIVER..1-2
Unpacking inspection..1-2
Standard specifications and performance parameters1-3
Driver nameplate description1-4
External dimensions and installation dimensions1-4
Confirmation and requirements of the installation space1-7
Notes on motor and load1-7
Notes on the driver1-8
Notes on scrapping1-9
Chapter 2 wiring.2-1
Selection and connection of peripheral devices2-2
Wiring of the main circuit terminals2-3
Wiring of control circuit 2-10
Connection of the encoder interface2-15
Connection of the serial communication port 2-16
Chapter 3 - Manipulator application.3-1
0.4 ~ 18.5kw driver:
Configuration and key functions of the manipulator3-2
Operative mode of the driver3-3
Operative mode of the manipulator3-4
Use method of the manipulator3-5
Modify the parameters with the manipulator3-6
Monitor operating state with the manipulator3-7
22 ~ 315kw driver:
Configuration and key functions of the manipulator3-8
07

GS DRIVER

CTB

Operative mode of the driver.3-10

Operative mode of the manipulator.3-10
Use method of the manipulator.3-12
Modify the parameters with the manipulator.3-12
Monitor operating state with the manipulator.3-13
Chapter 4 - Test run....4-1
Basic procedure of test run4-2
Confirmation of connection of the main circuit4-2
Control circuit wiring confirmation4-3
Initial power-on of the driver4-3
Motor and driver parameters confirmation4-4
No-load test run4-4
Loaded test run4-4
Chapter 5 - Parameter list5-1
Parameter list description.............................................................................................5-2
Monitor parameter U1................................................................................................5-2
Monitor parameter U2..............................................................................................5-3
Monitor parameter U3..............................................................................................5-3
Initialize parameter An..............................................................................................5-3
Basic control parameter Bn..........................................................................................5-5
User parameter Cn.......................................................................................................5-6
Motor drive parameter Dn..........................................................................................5-8
Function parameter Fn.......... ........................................................................5-9
Function parameter In.................................................................................................5-9
Protection parameter Pn.............................................................................................5-10
System communication parameter Sn......................................................................5-11
Chapter 6 - Operation by function...6-1
Spindle control timing sequence state diagram6-2
Motor basic parameters setting6-2
Motor operating parameters..6-3
Operation panel operation..6-3
Analog quantity speed control..6-3
08

GS DRIVER

CTB

Acceleration and deceleration control parameters6-5

Accurate stop parameters6-6
Rigid tapping.. 6-7
PULSE control.. 6-8
Swing control.. 6-9
Multi-function terminal control.. 6-10
Chapter 7 Troubleshooting..7-1
List of fault alarm and remedies ..7-2
Common fault analysis...7-3
Alarm reset method.....7-7
Chapter 8 - Routine maintenance...................................................................................8-1
Prompt..........................................................................................................................8-2
Routine maintenance .................................................................................................8-2
Regular maintenance..................................................................................................8-3
Wearing parts of the driver ..........................................................................................8-3
Driver storage..............................................................................................................8-4
Driver warranty.............................................................................................................8-4

09

GS DRIVER

CTB

Installation
The chapter describes matters to be confirmed and installation requirements for the user
after getting the GS driver.
Introduction to GS DRIVER.1-2
Unpacking inspection1-2
Standard specifications and performance parameters1-3
Driver nameplate description...1-4
External dimensions and installation dimensions.....1-4
Confirmation and requirements of the installation space.....1-7
Notes on motor and load...1-7
Notes on the driver....1-8
Notes on scrapping....1-9

GS DRIVER

CTB

Introduction to GS DRIVER
GS DRIVER is a type of spindle driver that specifically designed for CNC machine tool.
Precise control of position, speed, acceleration and output torque of AC induction servo
motor and ordinary inverter motor is allowed through the driver. It can be used for control of
spindle motor of machining center, CNC milling machine, CNC drilling machine, CNC lathe,
CNC grinder, and feed motor of large gantry equipment and vertical lathe. To achieve the
best operation effect, please complete wiring with CNC system by the " CTB servo
application manual ", and carry out installation and commissioning in accordance to the
manual.

Model description
GS driver series servo driver is suitable for motor with capacity from 1.5 to 315kw. Please
see the 21 models shown in Table 1-1.

Table 1-1 GS driver model (rated voltage: 400v)

Driver model

Rated
capacity(KVA)

Rated input
current (A)

Rated output Adapt motor

current (A)
power (kW)

Built-in
brake unit

BKSC-41P5GS

2.5

1.5

Yes

BKSC-42P2GS

2.2

Yes

BKSC-43P7GS

5.5

3.7

Yes

BKSC-45P5GS

8.5

14.2

13

5.5

Yes

BKSC-47P5GS

11

18

17

7.5

Yes

BKSC-4011GS

17

26

25

11

Yes

BKSC-4015GS

21

35

32

15

Yes

BKSC-4018GS

24

38.5

37

18.5

Yes

BKSC-4022GS

30

46.5

45

22

Yes

BKSC-4030GS

40

62

60

30

Yes

GS DRIVER

CTB

BKSC-4037GS

50

76

75

37

Yes

BKSC-4045GS

60

92

90

45

Yes

BKSC-4055GS

72

113

110

55

Yes

BKSC-4075GS

100

157

152

75

Yes

BKSC-4090GS

116

190

185

90

No

BKSC-4110GS

138

236

230

110

No

BKSC-4132GS

167

288

280

132

No

BKSC-4160GS

200

345

336

160

No

Unpacking inspection
Please confirm the following items when you get the product. Please contact directly with
the dealer or manufacturer that purchased from for any adverse situation. Please see Table
1-2 for detail.
Table 1-2 Confirm items
Confirm item

Confirm method

Confirm that the materials listed on

the packing list are complete.

Check the materials in the packing against the

packing list stuck to the external packing.

Are they in line with the ordered

merchandise?

Please confirm the label at the side of the driver.

Is there any damage?

Check the overall appearance for damage during

transportation.

GS DRIVER

CTB

Standard specifications and performance parameters

Please see Table 1-3 for standard specifications and performance parameters of 3-phase Class 400V driver
Table 1-3 Standard specifications and performance parameters of GS driver
Model BKSC-GS
Adapt motor power kW
Capacity

KVA

Output

Current A

41P5 42P2 43P4 45P5 47P5 4011 4015 4018 4022 4030 4037 4045 4055 4075 4090 4110 4132 4160 4185 4220 4315
1.5

2.2

3.7

5.5

7.5

11

15

18.5

22

30

37

45

55

75

2.5

5.5

8.5

11

17

21

24

30

40

50

60

72

100 116 138 167 200 280 340 460

13

17

25

32

37

45

60

75

90

110 152 185 230 280 336 370 450 630

Power

Maximum output voltage V

3-phase 380/400/415/440V corresponding input voltage

Maximum output speed rpm

4-pole motor 15000rpm: 500Hz

Rated voltage and frequency

3-phase 380/400/415/440V: 50/60Hz5

Allowed voltage pulsation

10, 15

Control mode

Sine wave PWM modulation, entirely closed-loop vector control

Torque

200% rated torque output below the fundamental frequency. Accuracy: 5

feather

90

Control characteristics

Range of speed regulation

1: 5000

Speed control accuracy

0.1%

Frequency set resolution

Digital quantity: : 0.01Hz; analog quantity: Unipolar,

frequency is / 2046

Position control accuracy

1PULSE

Acceleration

0.053000Hz/s

Brake mode

dynamic braking. 125 rated torque: built-in braking unit (external braking resistor)

Overload capacity

200% rated current 30s

110 132 160 185 220 315

maximum output frequency is /4092; bipolar, maximum output

GS DRIVER

CTB

Input output interface

Spindle
function
Protection
function
Service
environment

Digital quantity input

7-channel isolation photo-coupler input; input mode: PNP, NPN optional

Digital quantity output

2-channel isolation photo-coupler output; 24V, 10mA

Analog quantity input

3-channel; 10V+10V

Analog quantity output

None

Relay output

1 channel N.O. type; AC250V/DC30V, 1A

Fault output relay

1 channel: a group of N.O/N.C contact; AC250V/DC30V, 1A

Encoder input interface

One: maximum receive frequency is 300KHz; cable driven receive mode: RS422 standard

PULSE input interface

One: direction PULSE or orthotropic PULSE

Encoder output interface

One: maximum output frequency is 300KHz; cable driven output mode: RS422 standard

Bus interface

RS232canEthernet network

Speed control

Range: 015000rpm; turning: positive and negative; speed order: analog quantity, imPULSE frequency and bus

Accurate stop

Accuracy: 1PULSE; position adjustment: set by user's parameter

Rigid tapping

May be connected to several domestic and foreign system. Tapping error: 2

Other function

C-axis control, thread cutting, electronic gear, reaming, swing control

Spindle motor over-current

Greater than 200% rated current output

Motor overload

Specified time of exceeding overload alarm value. Alarm output: set by parameters

Overvoltage

The voltage of main circuit bus is higher than 800V. Alarm output

Low voltage

The voltage of main circuit bus is lower than 400V. Alarm output

Service site

Free of dust, corrosive gas and inflammable gas

Temperature

1045

Humidity

Lower than 95RH (no condensation)

Vibration

vibration frequency20Hz: 9.8m/s220Hzvibration frequency50Hz: 2m/s2

1 channel, 010V 2-channel

GS DRIVER
Driver nameplate description

CTB

Nameplate which indicates model and rated values of the driver is affixed to the lower right
of housing of the driver. The content of the nameplate is shown in Figure 1-1.

Figure 1-1 Servo driver nameplate

External dimensions and installation dimensions

1. 1.5-3.7kw driver
Please see diagram 1-2 for external dimensions and installation dimensions

Figure 1-2
Table 1-4 Dimensions (mm) and weight (kg) of GS DRIVER (1.5-3.7kw) driver
Dimension
Model

Connecting
terminal screw

Installati
on screw

Weight (kg)

45.5

276

91

290

200

Wire nail width

3mm

M6

BKSC-41P5GS
BKSC--42P2GS
BKSC--43P7GS

2. 5.511kw driver

GS DRIVER

CTB

Please see diagram 1-3 for external dimensions and installation dimensions

Figure 1-3
Table 1-5 Dimensions (mm) and weight (kg) of GS DRIVER (5.5-11kw) driver
Dimension
Model

Connecting
terminal screw

Installation
screw

Weight
(kg)

80

276

132

290

200

Wire nail width

3mm

M6

BKSC--45P5GS
BKSC--47P5GS
BKSC--4011GS

3. 1545kw driver
Please see diagram 1-4 for external dimensions and installation dimensions.

Figure 1-4
Table 1-6 Dimensions (mm) and weight (kg) of GS DRIVER (15-45kw) driver

GS DRIVER

CTB

Dimension

Connecting
terminal screw

Installation
screw

Weight
(kg)

140

376

194

390

228

M6

M6

14

236

376

282

390

228

M6

M8

20

300

376

380

390

269

M8

M8

26

Model
BKSC--4015GS
BKSC--4018GS
BKSC--4022GS
BKSC--4030GS
BKSC--4037GS
BKSC--4045GS

4. 55160kw driver
Please see diagram 1-5 for external dimensions and installation dimensions

Figure 1-5
Table 1-7 Dimensions (mm) and weight (kg) of GS DRIVER (55-160kw) driver
Dimension
Model
BKSC--4055GS
BKSC--4075GS

Connecting
terminal screw

Installati
on screw

Weight
(kg)

392

376

472

390

269

196

M10

M8

33

360

690

464

720

320

180

M10

M16

90

BKSC--4090GS
BKSC--4110GS
BKSC--4132GS
BKSC--4160GS

5.185 ~ 315kw driver

Please see diagram 1-6 for external dimensions and installation dimensions

GS DRIVER

CTB

Figure 1-6
Table 1-8 Dimensions (mm) and weight (kg) of GS DRIVER (185-315kw) driver
Dimension
Model

Connecting
terminal screw

Installation
screw

Weight
(kg)

800

1800

450

230

BKSC -4185GS
BKSC -4220GS
BKSC -4315GS

Confirmation and requirements of the installation space

Installation environment
The following items shall be noted when selecting the installation environment:
1. Ambient temperature: operate in -10 ~ 45; if the ambient temperature is higher than
45, the equipment shall be used with 30% derating for each 5 temperature rise.
Note: If the ambient temperature is higher than 45 , the ventilation shall be
strengthened, and use by the specified derating.
2. The humidity of the installation site shall lower than 95%, and free of condensing;
3. Do not install the equipment in place with dust or metal powder;
4. The equipment shall be installed at place without corrosive, explosive gas;
5. The equipment shall be installed at place that meet the requirements of vibration. The
vibration frequency 20Hz: 9.8m/s2; 20Hz vibration frequency 50Hz: 2m/s2;
6. The equipment shall be installed at place away from direct sunlight.

Installation direction and space

Installation spacing and distance requirements of single driver are shown in Figure 1-7.
Generally, abreast installation mode is adopted when multiple drivers are installed in the

GS DRIVER

CTB

control cabinet, and air inlet, outlet and dedicated cooling fan shall be equipped; if up and
down installation mode is adopted, stream guidance clapboard shall be added between
drivers to guarantee good cooling effect as shown in Figure 1-8.

Figure 1-7 Single controller installation

Figure 1-8 Multiple controllers installation

Notes on motor and load

Compared with frequency conversion operation
GS DRIVER is full closed-loop vector servo driver. It adjusts output voltage and current
automatically according to the load change. It's more energy-efficient than inverter with
higher speed control accuracy and wider speed regulation range. As the controlled motor
and driver are closed loop, the control of position, speed and torque can be achieved
conveniently.
Constant torque operation
When motor works in constant torque area, the output torque of the motor is required by the
mechanical operation instead of the rated torque of the motor. However, the maximum
continuous output torque of the motor must not exceed the rated torque.
High-speed operation in constant power area
For high-speed operation in constant power area, the increased vibration and noise shall
be considered, and the service speed range of motor bearing and mechanical devices must
be confirmed, and consulted in advance. It's strictly prohibited to make the machine operate
above the rated speed.

GS DRIVER

CTB

Lubrication of the mechanical device

For reduction box and gear head motor and other mechanical device that requires
lubrication, damage may be caused due to deterioration of lubricating effect in long-term
low-speed operation. It must be consulted in advance.
Negative torque load
Negative torque load occurs frequently for load such as lifting. The driver will generate
over-current and overvoltage alarm and trip. Equipping of brake components or mechanical
safety devices shall be considered.
Reciprocating load
Please pay attention to unstable phenomenon in output current when the driver is driving
piston reciprocating load. The phenomenon is more prominent in long-term low-frequency
operation. The capacity of driver shall be increased.
Mechanical resonance point of the load device
The driver may encounter the mechanical resonance point of the load device in certain
output frequency range. It can be avoided by setting jump frequency.

Notes on the driver

Applications not in rated voltage
The servo driver shall not be used in voltage that not in the working voltage range. Please
conduct voltage transformation with appropriate step-up or step-down unit as required.
Note on the drive phase input into 2-phase input
The device shall not be changed into 2-phase input, otherwise, default phase protection will
occur.
Capacitor or pressure-sensitive device to improve power factor
As shown in Figure 1-9, the output of the driver is PULSE wave, drive failure tripping or
damage to the device will be caused due to capacitor or pressure-sensitive device for
lightning to improve power factor installed at the output side. They must be removed.

GS DRIVER

CTB

Figure 1-9 Capacitor is prohibited at the output end of controller

Lightning attack protection

lightning over-current device is equipped in the driver for self-protection to induction stroke

Altitude and derating operation

For areas with altitude over 1000 m, derating operation is necessary due to deterioration of
cooling effect of the drive caused by thin air. The relationship curve of rated current of driver
and altitude is shown in Figure 1-10.

Figure 1-10 Derating curve of rated current of driver and altitude

Notes on scrapping:
Explosion of electrolytic capacitor: the electrolytic capacitors on main circuit and printed
panel may explode when incinerated.
Plastic incineration waste gas: toxic gases will be generated in incineration of front panel
and other plastic parts.
Processing method: please process the waste as industrial waste.
Description: The contents of the manual are subject to change due to product upgrade
or optimize. The new version shall prevail.

GS DRIVER

CTB

Wiring
The chapter describes the wiring specifications of power supply terminals and control circuit
terminals, and install wiring specifications of control board jumpers and expansion interface
board.
Selection and connection of peripheral devices..2-2
Wiring of the main circuit terminals2-3
Wiring of control circuit .2-10
Connection of the encoder interface..2-15
Connection of the serial communication port ..2-16

GS DRIVER
Selection and connection of peripheral devices

CTB

Spindle driver and peripheral devices connection diagram, take 15kw drives as an example
in Figure 2-1.

Figure 2-1 Spindle driver and peripheral devices connection diagram

Parts selection description
Item

Usage

Selection note

Remarks

Air circuit breaker

Turn on or off driver

power

Select by 150% of rated

current of the driver

Refer to Table 2 - 3

Electromagnetic
contactor

For automatic power on

of driver

Select by 150% of rated

current of the driver

Refer to Table 2 - 3

Input side reactor

Improve power factor of

power grid

Select by 100% of rated

current of the driver

Input noise filter

Suppress interference of
driver to power supply

Select by 150% of rated

current of the driver

Braking resistor

Consume regenerated
energy of the driver

Select by standard provided

by the factory

Refer to Table 2 - 2

Suppress wireless
Filtering magnet
Select by standard provided
interference of the driver
ring
by the factory
to outside

Refer to GS model
selection sample

GS DRIVER

CTB

Wiring of the main circuit terminals

The structure of the main circuit
See Figure 2-2A, 2-2B and 2-2C for internal structure diagram of the main circuit.

Figure 2-2A 1.515kw main

circuit composition

Figure 22B 18.575kw main

circuit composition

Figure 22C 90160kw main

circuit composition

Main circuit terminals composition

1.522kw main circuit terminals composition

3775kw main circuit terminals composition

90160kw main circuit terminals composition

Main circuit terminals and functional description

Item
R S

Function

Notes

3-phase AC supply input terminal.

Need to install breaker for protection

GS DRIVER

CTB
380~440V, 50/60Hz

P P1

DC bus positive pole

P and N are for input of external

braking unit or DC power input

P2

DC reactor wiring terminal

P1 and P2 are for external DC reactor

Pb

Braking resistor wiring terminal

P, P2 and PB are for external braking

resistor

DC bus negative pole

N and P are for external braking unit

or DC power input

U V w

Driver output terminal

Consistent with the phase sequence

of the motor during wiring

Earth terminal

C type grounding, the grounding

resistance 4

Wiring of input side of the main circuit

Please pay attention to the following items for wiring of input side of the main circuit. See

Figure 2-3 for standard wiring.

Incoming line circuit breaker (MCCB)

The main circuit power input terminals (R, S, T) must be connected to 3-phase AC power
through line protection circuit breaker (MCCB).
The selection of MCCB must be in accordance with requirements in Table 2-3.
The time characteristics of MCCB must take overload characteristics (rated output current
200%/min) and time characteristics of the servo driver into account.
Each servo driver shall be equipped with independent breaker; when multiple drivers
share a circuit breaker, to cut off the power supply and prevent the failure expansion during
driver failure, it's recommended to control the incoming line electromagnetic contactor with
the fault output relay of the driver to ensure safety.

GS DRIVER

CTB

Installation of the residual current circuit breaker

The output of the servo driver is a high frequency PULSE wave so that there is
high-frequency leakage current generated. Residual current circuit breaker can be used at
the incoming line side of the driver to remove high-frequency leakage current, and only
inspect channel current that dangerous to human body. Please select special residual
current circuit breaker for servo (inverter) for wiring.
When select special residual current circuit breaker, please select model for control of
one driver with an induction current over 30ma.
When select normal residual current circuit breaker, please select model for control of one
driver with an induction current over 200ma, and a time over 0.1s.
Installing isolation transformer between normal residual current circuit breaker and servo
driver can effectively avoid malfunction of the breaker.

Incoming line electromagnetic contactor

Incoming line electromagnetic contactor may be used to cut off the power in sequential
control. It cannot be used as start of servo driver. When cut off power of servo driver
compulsorily with incoming line electromagnetic contactor, servo driver is in power-off
alarm state, motor only can slide freely and stop.
Frequent turning on/off incoming line magnetic contactor may cause heating, even
burning of charging resistor of the driver (driver interior).
The time interval of turning on/off incoming line magnetic contactor shall be longer than
10 minutes.

AC reactor
Installing AC reactor at the incoming line side of the servo driver can effectively suppress
the surge of power, avoid burning of rectification part of the driver, and also can improve the
power factor of the power supply side. Please see Figure 2-3 for connection of AC reactor,
see Table 2-1 for selection of AC reactor.

DC reactor
External DC reactor can be connected to GS servo driver above 22KW. It can effectively
suppress the surge of power, avoid burning of rectification part of the driver, and also can
improve the power factor of the power supply side. Please see Figure 2-4 for connection of
DC reactor.
External DC reactor shall not be connected to GS servo driver lower than 15 KW. For GS
servo driver above 22KW without external DC reactor shall have P1, P2 or D C + terminals
shorted as shown in Figure 2-5.

GS DRIVER

CTB

Figure 2-4 DC reactor connection diagram

Figure 2-5 Connection diagram without DC reactor

Precautions for wiring of DC reactor

1. Please do not connect DC reactor to any main circuit terminal except P1, P2, otherwise,
it may cause internal short circuit of the driver, and burn the driver.
2. Please see Table 2-3 for specifications of DC driver connecting cable, the standard of
the main circuit cable.
3. Please see Table 2-1 for selection standard of DC reactor.
4. With external DC reactor, the P2 terminal shall be multiplex terminal, and one end of
braking resistor also shall be connected to the terminal.
Table 2-1 Selection of AC reactor, DC reactor and input filter
Driver model

41P5 42P2 43P7 45P5 47P5 4011 4015 4018 4022 4030 4037 4045 4055 4075 4090 4110 4132 4160

7
10
15
20
30
40 50 60
80
90
120 150 200 230 250 290 330
AC Current (A) 5
reactor Model ACL 0005 0007 0010 0015 0020 0030 0040 0050 0060 0080 0090 0120 0150 0200 0230 0250 0290 0490
DC Current (A) 15
reactor Model DCL 015
Input Current (A) 6
filter Model EMI 06

20

25

30

35

40

50

60

80

90

110

020

025

030

035

040

050 060 070 080

090

0110 0150 0180 0200 0250 0270 0360

10

16

25

30

65

80

100

06

06

010

016

025

030 050 050 065

080

0100 0120 0150 0200 0250 0250 0320

50

70

50

150

120

180

150

200

200

250

250

270

250

Power side noise filter

In command to reduce high-frequency interference noise from power line coupling to the
driver, and suppress the noise feedback to power from the driver, noise filter with
appropriate model and specifications at the power input side of the driver.
Set and connect the incoming line filter correctly as shown in Figure 2-6.

360

320

GS DRIVER

CTB

Figure 2-6 Correct installation of noise filter at the input side of the power supply
Please see Figure 2-6 for examples of incorrect settings and connection

Figure 2-7 Incorrect settings and connection of noise filter at the input side of the power
supply

The wiring of output side of main circuit

The output terminals of U, V, and W of the driver shall be connected to the connecting
terminals of U, V, and W of three-phase AC motor by correct phase sequence; if the phase
sequence is connected wrongly, the driver will raise the wrong phase sequence alarm with
an alarm number of [Link]. To solve the problem, exchange phase sequence of any two
phases. Please see Figure 2-8 for standard wiring of the output side.

GS DRIVER

CTB

Figure 2-8 Output side wiring

Caution

The servo driver and motor must be well grounded, otherwise it may make

the driver not functioning properly, even burn the driver.

Forbid
It's strictly prohibited to connect the input power cord to the output terminal.
Never connect the input power cord to the output terminal, otherwise, it will lead to
damage to internal components of the controller.
It's strictly prohibited to connect make the output terminal shorted and
grounded.
Never touch the output terminal directly, or make the output line touch the
controller housing for risk of electric shock. In addition, never short the output line.
It's strictly prohibited to use phase shift electrolytic capacitor, LC / RC noise
filter.
Never connect phase shift electrolytic capacitor, LC / RC noise filter in output
circuit. Damage to internal components of the controller may be caused when use
these components.
It's strictly prohibited to connect or disconnect load with electromagnetic switch.
Never connect electromagnetic switch, electromagnetic contactor to connect or
disconnect the load in output circuit. During load operation, the protection circuit
action of the controller will be acurated by the surge current.
surge current will arose
It's strictly prohibited to connect fan of spindle motor to U / V / W output
terminals of the driver.
It may burn the fan, and short-circuit the driver.

Wiring distance between the driver and motor

Generally, the wiring distance between the servo driver and motor shall be shorter than 50
m. For longer distance, please contact the manufacturer to select wire with samller
resistivity.

GS DRIVER

CTB

Inductive interference countermeasures

Three methods of suppressing radio interference and inductive interference are provided in
the information: filter magnetic ring, shielded cable and output filter.

Filter magnetic ring

Installing filter magnetic ring at the output side near to the driver can suppress common
code interference at the output side effectively, as shown in Figure 2-9.

Figure 2-9 Filtering magnetic ring installation diagram

Output shielded cable

Use shielded cable for output line of the servo driver can effectively suppress radio
interference and inductive interference. The ends of shielding layer of the shielded cable
shall be grounded separately as shown in Figure 2-10.

Figure 2-10 Connecting method of shielded cable

For applications of input and output filters in occasions with relatively large radio
interference, output filter can be used to suppress interference. The input side and the drive
generate radio interference so that the effect is best by using the input, output filter at the
same time, as shown in Figure 2-11.

Figure 2-11 Supress radio interference with output filter

GS DRIVER

CTB

Connection of the grounding wire

The ground terminal is identified as E or

, please do ground.

Earth resistance: below 4.

Do not share grounding wire with welder and other power equipment.
Please select wire diameter specification for grounding wire as specification in technical
standards of electrical equipment, and as short as possible.
Please make grounding wire forming a loop where more than two drivers are used.
Example: as shown in Figure 2-12

Figure 2-12 Connection of grounding wire

Connection of braking resistor

The P, PB terminals on main circuit block of servo driver are for connection with braking
resistor. Please do not connect braking resistor to other terminals, otherwise, the braking
resistor will heat up and burn out, or cause damage to the driver. Please see Table 2-2 for
braking resistor selection.
The connection of braking resistor shall be in strict accordance with Figure 2-13.
The length of connecting wire between driver and braking resistor shall be less than 50
m.
Please pay particular attention to: external braking unit may be connected to p (+) / DC +,
N (-) / DC side of the driver, but direct connecting with braking resistor is not allowed,
otherwise, damage to driver or fire may be caused.
1.5 ~ 15kw braking resistor
wiring diagram

18.5 ~ 75kw braking resistor

wiring diagram

90 ~ 150kw braking resistor

wiring diagram

Figure 2-13 Connection of braking resistor

GS DRIVER

CTB
Table 2-3 Specification of braking resistor

BKSC-XXXX GSX

ripple
Braking
resistor

41P5 42P2 43P7 45P5 47P5 4011 4015 4018 4022 4030 4037 4045 4055 4075 4090 4110 4132 4160 4185

4220

4315

Power W 400 1000 1000 1500 2000 2000 1500 2000 2000 2500 2500 2500 2500 2500 2500 2500 2000 2000 2000

2000

2000

Resistance
300 160

Qty.

40

40

32

32

40

40

40

55

55

55

55

55

55

55

40

40

40

40

40

10

12

12

12

16

Power W 300 300 600 600 800 1000 600 800 800
aluminum Resistance
100 100
housing

50

50

40

32

50

40

40

Qty.

Same parameters for ripple resistor

Filteringinside diameter (mm) 1 5

magnet
Thickness H(mm)
13
ring

15

15

18

18

23

23

23

27

27

38

38

38

38

38

44

44

44

13

13

13

13

15

15

15

15

15

24

24

24

24

24

15

15

15

Note: above accessories data is standard data recommended by the manufacturer. For
special applications, please contact your supplier.

Selection of breaker, contactor and cable

Please see Table 2-3 for selection of breaker, contactor and input and output cable
Table 2-3 Specification of breaker, contactor and cable
Main circuit cable
Breaker
(copper conductor
(air switch) (A)
cable) (mm2)

Contactor
Voltage: 380V.
Current:(A)

Model
BKSC

Power
(kW)

41P5GS

1.5

10

2.5

42P2GS

2.2

10

2.5

43P7GS

3.7

16

16

45P5GS

5.5

32

18

47P5GS

7.5

40

25

4011GS

11

63

10

32

4015GS

15

63

16

50

4018GS

18.5

100

16

63

4022GS

22

100

25

80

4030GS

30

125

35

95

4037GS

37

160

35

115

4045GS

45

200

50

115

4055GS

55

200

70

150

4075GS

75

250

95

185

4090GS

90

315

95

250

GS DRIVER

CTB

4110GS

110

400

120

250

4132GS

132

400

150

315

4160GS

160

630

185

400

Main circuit wiring precautions

Please do connect breaker or fuse between power supply and power input terminals (R,
S, T) of the driver.
Please do connect to earth wire at E terminal of the driver. Copper core cable over 4mm2
shall be used for earth wire with a grounding resistance lower than 4.
Please ensure the high reliability of wiring.
Please check the following items after circuit wiring.
(1) Are all connections correct?
(2) Is there connection missing?
(3) Is there short circuit between terminals and connecting line or shorted to ground?

Control circuit wiring

Input and output signals of GS Series servo driver include: switching value input signal,
switching value output signal, analog quantity input signal, PULSE input signal, encoder
input / output signal.

Specifications of input and output signal cable

As the control signals are different, the requirements to cable for connector are strict.
Specifications of cable for different signal connectors are listed in Table 2-4. User shall
follow the standard for wiring.
Table 2-4 Specifications of input and output signal cable
Signal

Signal name

switching value
input /output
Relay output

i1i6
M0A/M0b/M0c

analog quantity
signal
Encoder signal
PULSE signal
enable reset
signal

Q0Q1
M1A/M1b/M1c

FI FV FS

Fc FS FT

PV1 G1 A+ A- B+ B- Z+ ZPV2 G2 OA+ OA- OB+ OB- OZ+ OZSA+

SA- Pb+
ST

Pb-

Dz+

Dz-

Cable

Cable
specification

common cable or
shielded cable

0.2~2

common cable or
shielded cable

0.2~2

shielded cable

0.2~1

Shielded twisted
twin cable

0.2~1

Shielded twisted
twin cable

0.2~1

common cable or
shielded cable

0.2~1

GS DRIVER

CTB

GS driver control panel specifications

GS Series driver provides two kinds of control board according to different power and
function of GS Series driver. Please see Table 2-5 for interface characteristics and
applicable model.
Table 2-5 GS driver main board specifications
Control
panel
model

switching switching
value
value
input
output

analog
quantity
input

PULSE
input

Communication Encoder Encoder

interface
input
input

cP100c

RS232

cP100b

RS485/TcP/iP

cP100A

RS232

Applicable
power
18.5160Kw
1.5-15Kw

GS DRIVER

CTB

Control signal wiring diagram

Wiring diagram of GS driver equipped with CP100 series main board

Input and output signals description (CP100 Series)

Table 2-6 Input and output signal function description

GS DRIVER
Port

Type

T0

Communication

T1

CTB
Pin

Programmable
optocoupler
output
2

RS232

FS

10V power for speed setting is

Dc10V 50mA
provided inside common port

Fc

analog input /output

FV

-10V +10V analog input,

impedance: 20K

Fi

Analog input impedance may be 0V

selected for 0 10V , 4 20mA
impedance: 20K/500

FT

010V analog input

Q1

speed reached

Q2

driver ready

input

24V optocoupler
output 10mA

ST

control enabling and reset

i1

foreword operation enabling PULSE

speed

i2

reverse operation direction

i3

accurate stop, close: start accurate

stop and maintain; open: cancel
accurate stop

i4

rigid tapping signal, close : enter rigid

tapping state

i5

Swing signal, close: enter swing state

for mechanical shifting

i6

multifunctional
defined)

PV

DC24V power output terminal

Sc

DC24V power 0V terminal /control Dc24V 500mA

signal common port

3/4

PV2/G2

Preset power, provided by digital

system, system without electrify Dc5V100mA
inspection may go without.

5/15

OA + OA

encoder A phase output

10/14

Ob + Ob-

encoder B phase output

9/13

Oz + Oz

encoder Z phase output

1/2

SA + SA

encoder A phase/orthogonal PULSE

RS422/485
A phase input /single PULSE train
standard
input P

Control signal
input
T3

Control power

Encoder
PULSE input

Signal standard

MOA/MOb/M output accurate stop end (in place)

Ac250V 1A
Oc
output
Dc30 1A
MIA/MIb/MIc driver fault output

Relay output

Encoder output

Function
communicate with computer

Analog input

T4

Name

terminal

(can

PNP: 0V input
effective
NPN:24V
input
effective
Input mode of
PNP or NPN
Shall be selected
by
software
parameter setting

be

line driver output

RS 422 standard

GS DRIVER

T5

Communication
encoder input

Thermal
protection input

CTB
encoder B phase/orthogonal PULSE
B phase input /single PULSE direction
input D

7/6

Pb + Pb

12/11

Dz + Dz-

encoder Z phase

12/13

PV1/G1

encoder power supply provides

Dc5V
terminal /power common port

8/3

A + A

encoder A phase input

9/4

b + b

encoder B phase input

15/14

z + z

encoder Z phase input

11

T1

Motor thermal protection signal input

100mA

line driver accepts

RS422standard

N.C./ N.O.

Connector terminal arrangement

T4 D-type 15-pin plug (pin)

T5 D-type 15-pin plug (hole)

Control power supply wiring

In addition to analog control terminal, all of other control terminals of GS series servo driver
are equipped with optocoupler isolation. Power of the optocoupler isolation may select from
internal of the driver or external power provided by the user according to the actual
requirements. To ensure better isolation effect, it is recommended to use external DC24V
isolation power provided by user.

The wiring of relay output signal

T3 interface of GS servo driver provides two relay output points.
Output standard: AC250V 1A DC30V 1A
Accurate stop relay output schematic diagram

Fault relay output schematic diagram

Transistor output wiring precautions

The maximum oad capacity of output tape of transistor output QI/Q2 is 20 mA, and the

GS DRIVER

CTB

output voltage is DC24V.

If the output terminal needs 0V, intermediate relay may be installed for switching as
shown in Figure 2-14.
If the output terminal drives inductive load (e.g., electromagnetic relay, intermediate
relay), surge voltage absorbing circuit shall be added as shown in Figure 2-14.
If follow current diode is installed in surge absorption circuit (for DC electromagnetic circuit),
attention must be paid to polarity during installation.

Figure 2-14 Transistor output circuit

Wiring of analog input signal

When GS servo driver selects C P100A/C P100B/C P100C main board, T1 port provides
three sets of analog input interfaces of FI, FV and FT, as well as a group of power interface
FS and fc for analog input. Please see Table 2-6 for signal function description.
Table 2-6 Analog interface signal description
Signal

Function

Signal standard

FT

Select 420mA input

and plug J1
j1
jumper

Unipolarity analog input terminal

420mA, input impedance: 250

FI

Unipolarity analog input

terminal
Bn02=1

010V, input impedance: 20K

Signal

Function

Signal standard

FV

Bipolarity analog input

terminal
Bn020

-10V+10V analog input,

input impedance: 20K

FS

inside provided speed

setting power

DC10V50mA,

Fc

analog common port

0V

Shielding layer

GS DRIVER

CTB
connecting terminal

Wiring requirements
Connect to signal source or control signal with multi-core shielded cable or stranded
shielded wire.
The near-end of shielding layer of the case (end near the driver) shall be connected to the
connector housing.
During wiring, the control cables shall be arranged more than 30cm away from the main
circuit and strong power line (including power line, motor line, relay, contactor connecting
cable), and avoid parallel layout. Vertical wiring is recommended to prevent malfunction of
the driver due to interference.
Filter magnetic ring provided by the manufacturer shall be used for long distance wiring. It
shall be installed at the side near the driver.

FI terminal wiring example

Use internal power for speed setting. The input signal is 0 ~ 10V as shown in Figure 2-16.

Figure 2-16 Conduct speed setting with internal power

FV terminal wiring example

CNC system uses bipolar (-10V ~ +10 V) analog output. The speed is determined by the
value of the analog, the direction of rotation is determined by polarity of the analog as
shown in Figure 2-17.

GS DRIVER

CTB

Figure 2-17 Bipolar speed setting is conducted by CNC system

Forbid
It's prohibited to connect the signal line and OV reversely. The signal line is likely
to be burned, and reverse operation may be caused for bipolar.
It's prohibited to connect high-voltage to analog signal terminal. The driver may
be burned.

Connection of the encoder interface

A group of encoder input interface T5 and encoder input interface T4 are provided on main
board of GS series servo driver. Please see Table 2-7 and Table 2-8 for interface definition.
Table 2-7 Encoder input interface T5
Signal

Description

Signal standard

PV1

Encoder power supply DC5V

G1

Encoder power ground 0V

A+

A phase PULSE same-phase input (+)

A-

A phase PULSE same-phase input (-)

B+

B phase PULSE same-phase input (+)

B-

B phase PULSE same-phase input (-)

Z+

Z phase PULSE same-phase input (+)

Z-

Z phase PULSE same-phase input (-)

T1

Motor thermal protection input terminal

DC5V/100mA

Line drive mode

RS422 standard

24V optocoupler isolation input

Table 2-8 Encoder input interface T4

Signal

Pin

Description

Signal standard

PV2

Encoder power supply

DC5V

G2

Encoder power ground 0V

OA+

A phase PULSE same-phase input (+)

OA-

15

A phase PULSE same-phase input (-)

OB+

10

B phase PULSE same-phase input (+)

OB-

14

B phase PULSE same-phase input (-)

OZ+

Z phase PULSE same-phase input (+)

OZ-

13

Z phase PULSE same-phase input (-)

SA+

PULSE/encoder A phase input (+)

SA-

PULSE/encoder A phase input (-)

PB+

PULSE/encoder B phase input (+)

PB-

PULSE/encoder B phase input (-)

Or external sensor
power

DC5V/100mA

Line drive mode

RS422 standard

Line drive mode

RS422 standard

GS DRIVER

CTB

DZ+

11

PULSE/encoder Z phase input (+)

DZ-

12

PULSE/encoder Z phase input (-)

Encoder wiring precautions

The encoder cable must be shielded twisted pair cable. Please see Table 2-4 for cable
requirements.
The shielding layer shall be connected to the connector housing.

Forbid
It's prohibited to connect the DC5V power reversely. It's likely to burn the DC5V power or
encoder of the driver.
It's prohibited to reverse the A, B phase sequence. Otherwise, the motor will not function
properly, or even burn the motor or driver.

Connection of serial communication port

GS driver provides users with a R S232A serial communication interface T0 for connection
with computer to realize transmission of program and parameters. The port is connected
with computer through RS232-P1 cable.
Please see Table 2-9 for definition of serial communication interface T0
Table 2-9 T0 interface definition
Pin

Name

Description

Pin

Name

Description

Send terminal

Used by manufacturer

Receive terminal

T0 interface diagram

General Purpose cable model: rs 232-p1

Caution
Please select the standard cable provided by the manufacturer for communication.

GS DRIVER

CTB

Manipulator application
The chapter describes the functions and methods of application of the manipulator.
0.4 ~ 18.5kw driver:
Configuration and key functions of the manipulator.3-2
Operative mode of the driver3-3
Operative mode of the manipulator.3-4
Use method of the manipulator3-5
Modify the parameters with the manipulator..3-6
Monitor operating state with the manipulator.3-7
22 ~ 315kw driver:
Configuration and key functions of the manipulator..3-8
Operative mode of the driver3-10
Operative mode of the manipulator.3-10
Use method of the manipulator...3-12
Modify the parameters with the manipulator.3-12
Monitor operating state with the manipulator3-13

GS DRIVER

CTB

Configuration and key functions of the 0.4 ~ 18.5kw manipulator

The chapter defines and describes terms and phrases for operation and state of 0.4 ~
18.5kw driver manipulator, defines the operation methods of driver and manipulator. Please
read carefully. It's very helpful for proper use of the 0.4 ~ 15kw driver.

Manipulator
The manipulator is one of the standard equipment of 0.4 ~ 18.5kw driver. User may carry
out parameter setting, state monitoring, operation control and other operations to the driver
through the manipulator. It's very important to be familiar with function and operation of the
manipulator for proper application of 0.4 ~ 18.5kw series driver. Please read the manual
carefully before using.

Manipulator appearance diagram

Manipulator of 0.4 ~ 18.5kw driver is mainly composed of two parts of LED digital tube and
keys. The appearance and functional zones are shown in Figure 3-12.

Figure 3-12 Manipulator diagram

GS DRIVER

CTB

Manipulator key function description

Please see Table 3-2 for function description of the manipulator key
Table 3-2 Manipulator key function
Key

Name
Menu selection
switching key

Function
switching key of each menu item;
It's used to switch data bit of the parameter number when browse

Shift key

parameter items;
When modifying data in program state, it can be used to modify
the modified bit of the modified data.

adjusting key

Increase menu item, parameter item or modified parameter value

progressively.
Press the key in program state to return to the previous menu.
Enter the next level menu;
Complete selection of the parameter group in1-level

menu;

Confirm / enter key Complete parameter value checking operation in 2-level menu;
Complete modification and storage operation of the parameter
value in 3-level menu;
It's used to reset driver fault when the driver is in fault alarm state.

The operating state of the driver

0.4 ~ 18.5kw driver has four operating states after power-on: standby, operating,
programming and fault alarm. They are described as follows:

Standby state
0.4 ~ 18.5kw driver is in standby state after power-on and before receiving any operating
control order. The default standby state display function code of LED digital tube is

. User

may make LED circling switch display U1, U2 and U3 monitoring function parameter groups
by press

key. After press

key, user may make LED circling switch display

monitoring parameters defined in function parameter group by pressing

then press

and

key, and

key to check /monitor its value.

It will be limited by H P password and functional parameter An00 and An46 when user want
to check / modify the content of parameter groups other than U1, U2 and U3 during
operation. Please see chapter " Function parameter list " for detail.

Operating state

GS DRIVER

CTB

When 0.4 ~ 18.5kw driver in standby and no-fault state, it will enter operating state after
receiving operating order.
In normal operating state, user may make LED circling switch display U1, U2 and U3
monitoring function parameter groups by press

key. After press

key, user may

make LED circling switch display monitoring parameters defined in function parameter
group by pressing

and

key, and then press

key to check /monitor its value.

Programming state
For 0.4 ~ 18.5kw driver, user may switch to the state in which function code parameters can
be modified through

and

on the operator panel. The state is programming

state.
Function parameter value is displayed in programming state, and the bit to be modified is
flashing.

Fault alarm state

In the state, 0.4 ~ 18.5kw driver fails and displays the fault code.
LED displays fault code in fault state, and user may conduct fault reset operation through
the operation panel.

Operative mode of the manipulator

Power-on initialization state:
During power-on of the driver, the manipulator conducts initialization process about 3
seconds. LED digital tube displays

in the process as shown in Figure 3-13.

Standby state:
The state of the manipulator is shown in Figure 3-14 when the driver is in standby state.
The LED digital tube default display

. At this point, user may press

to enter menu

items, and check or modify parameters.

Figure 3-13 Power-on initialization state

Figure 3-14 Standby state

GS DRIVER

CTB

Operating state:
The driver enters operating state after receiving correct operation command in standby
state. As shown in Figure 3-15, the LED digital tube default displays the set speed of the
driver, e.g F. 1500. In this state, user may press

to enter menu items, and check or

modify parameters.

Fault alarm state

When fault is detected as the driver is in operating, standby or programming state, the
corresponding fault information will be displayed immediately as shown in Figure 3-16.
When a fault occurs, user may conduct drive reset by pressing

. If the fault has

disappeared, it returns to the standby state; if the fault still exists, the fault code will be
displayed again.

Figure 3-15 Operating state

Figure 3-16 Fault alarm state

Parameter transmission state:

Parameter initialization will be carried out within the driver after power-on initialization
every time. The driving returns to normal state after parameter initialization. In this process,
LED digital tube displays

all the time as shown in Figure 3-17.

Password state:
The manipulator will prompt to enter a password as shown in Figure 3-18 when entering
programming state from standby and operating state as An00=1. The password must be
entered correctly in the state before entering the programming state

Figure 3-17 Parameter transmission state

Figure 3-18 Password state

GS DRIVER

CTB

Use method of the manipulator

The section mainly introduces use of the manipulator, and basic operations of functions.

Parameter setting operation process

Parameter setting method of manipulator of 0.4 ~ 18.5kw driver adopts three-level menu
structure. Parameter value of menu items can be checked and modified conveniently.
The three-level menu: menu item (1-level menu), parameter tem (2-level menu) and
parameter setting (3-level menu). The operation process is shown in Figure 3-19.

Figure 3-19 3-level menu operation flow chart

During operation in 3-level menu, user may return to 2-level menu by pressing

or

(see Figure 3-19 and Figure 3-20). The difference between the two operations: after press
ENTER key, the set parameter value will be saved to the controller, and then return to
2-level menu; it will return to 2-level menu directly without saving the parameter value by
pressing MENU. The detail operational procedures of 3-level menu are shown in Figure
3-20.

GS DRIVER
Modify the parameters with the manipulator

CTB

The flow chart of modify the parameters with the manipulator is shown in Figure 3-20.

Figure 3-20 3-level menu operation flow chart

Description:
Eight menu items are included in 1-level menu: Un menu, An menu, Bn menu, Cn menu,
Dn menu, Fn menu, Pn menu and In menu.
In 2-level menu, each group of parameter includes 48 parameters. Please see parameter
description for specific function.

User password function

To enhance reliability and security of parameter setting, manipulator of 0.4 ~ 18.5kw driver
has user password function. The operating process is shown in Figure 3-21. Please refer to
an22 for modification of user password. The default password is: 00000.

Figure 3-21 User password function operation flow diagram

GS DRIVER

CTB

Monitor operating state with the manipulator

Operation state, interface state and fault information of the driver can be monitored
respectively through U1, U2 and U3 of the manipulator

Operation state monitoring

Operation state monitoring includes set speed F, output speed O, feedback speed b, output
current A, output torque T and DC bus voltage U of the driver. Please see Figure 3-22 for
monitoring method.

Figure 3-22 Driver operation state monitoring flowchart

Interface state monitoring

Interface state includes switching value input terminal u2-2/u2-3, switching value output
terminal u2-4, analog input interface u2-5/u2-6, u2-7/u2-8 and encoder input interface
u2-0/u2-1. The monitoring method is same with monitoring parameter, only needs to select
corresponding parameter in U2.
Please see parameter table of parameter number.

Fault information monitoring

The control panel will display the current fault message code when the driver is in fault state.
The fault record of the driver can be checked through U3. The check operation is same with
monitoring parameter, only needs to select corresponding parameter in U3.
Please see parameter table of parameter number.

22315k w driver:
Configuration and key functions of the 22315k w driver manipulator
The chapter defines and describes terms and phrases for operation and state of 22
315kw driver manipulator, defines the operation methods of the driver and manipulator.

GS DRIVER

CTB

Please read carefully. It's very helpful for proper use of the 22315kw driver.

Manipulator
The manipulator is one of the standard equipment of 22315kw driver. User may carry out
parameter setting, state monitoring, operation control and other operations to the driver
through the manipulator. It's very important to be familiar with function and operation of the
manipulator for proper application of 22315kw series driver. Please read the manual
carefully before using.

Manipulator appearance diagram

Manipulator of 22315kw driver is mainly composed of three parts of LED digital tube,
LED indicator and key. The appearance and functional zones are shown in Figure 3-1.

Figure 3-1 Manipulator diagram

Manipulator key function description

Please see Table 3-1 for function description of the manipulator key

GS DRIVER

CTB
Table 3-1 Manipulator key function

Key

Name

Function

Menu select and switching key of each menu item;

switch key
Press the key in program state to return to the previous menu. Enter
the next level menu;
Complete selection of the parameter group in 1-level menu;
Confirm / enter Complete parameter value checking operation in 2-level menu;
key
Complete modification and storage operation of the parameter value
in 3-level menu;
It's used to reset driver fault when the driver is in fault alarm state.
up key

Increase menu item, parameter item or modified parameter value

progressively.

down key

Decrease menu item, parameter item or modified parameter value

progressively.

Shift key

It's used to switch data bit of the parameter number when browse
parameter items; When modifying data in program state, it can be
used to modify the modified bit of the modified data.

run command
key

It's used to start the driver in driver control mode;

fault reset key

It's used to reset driver reset when the driver is in fault alarm state.

direction
It's used to select rotation direction of the driver in manipulator
command switch command control mode; under terminal control, the indicator of the
key
key automatically displays rotation direction of the driver.

Manipulator LED indicator description

There are six LED indicators on the manipulator. They are on or off in various states. The
detail description is as follows:
Current display indicator A:
It has two states of on and off which indicates that the data displayed in the current LED
digital tube display zone is current parameter or not. On means current parameter is
displayed in the LED digital tube display zone; off means that it's not current parameter
displayed in the LED digital tube display zone.
Torque display indicator T:
It has two states of on and off which indicates that the data displayed in the current LED
digital tube display zone is torque parameter or not. On means torque parameter is
displayed in the LED digital tube display zone; off means that it's not torque parameter
displayed in the LED digital tube display zone.
Speed display indicator rpm:
It has two states of on and off which indicates that the data displayed in the current LED

GS DRIVER

CTB

digital tube display zone is speed parameter or not. On means speed parameter is
displayed in the LED digital tube display zone; off means that it's not speed parameter
displayed in the LED digital tube display zone.
Program running indicator EXT
It has two states of on and off which indicates that the driver program is running or not. On
means the driver program is running; off means the driver program isn't running;
Run state indicator RUN:
It has two states of on and off which indicates the run state of the system under various
operating control orders. On means the driver is in operating state; off means the driver is
shutdown.
Operating direction indicator REV:
It has two states of on and off which indicates the current operating direction of the driver.
On means reverse operation of the driver; off means forward operation of the driver.

The operating state of the driver

22 315kw driver has four operating states after power-on: standby, operating,
programming and fault alarm. They are described as follows:

Standby state
22315kw driver is in standby state after power-on and before receiving any operating
control order. The Run state indicator (RUN) on operation panel is off, and the default
tandby state display function code of LED digital tube is

. User may make LED circling

switch display U1, U2 and U3 monitoring function parameter groups by press

key,

and press , and > after pressing ENT to make LED circling switch display monitoring
parameters defined in function parameter group, and then press ENT to check /monitor its
value.
It will be limited by H P password and functional parameter An00 and An46 when user want
to check / modify the content of parameter groups other than U1, U2 and U3 during
operation. Please see chapter " Function parameter list " for detail.

Operating state
When 22315kw driver in standby and no-fault state, it will enter operating state after
receiving operating order. In normal operating state, the Run state indicator (RUN) on
operation panel is on. User may make LED circling switch display U1, U2 and U3

GS DRIVER

CTB

monitoring function parameter groups by press

key. Press , and > after pressing

ENT to make LED circling switch display monitoring parameters defined in function
parameter groups, and then press ENT to check /monitor its value.

Programming state
For 22315kw driver, user may switch to the state in which function code parameters can
be modified through MENU, ENT, , and > on the operator panel. The state is
programming state.
Function parameter value is displayed in programming state, and the bit to be modified is
flashing.

Fault alarm state

In the state, 22315kw driver fails and displays the fault code.
LED displays fault code in fault state, and user may conduct fault reset operation through
ENT and STOP/RESET on the operation panel.

Operative mode of the manipulator

Power-on initialization state:
During power-on of the driver, the manipulator conducts initialization process about 3
seconds. LED digital tube displays

in the process as shown in Figure 3-2.

Standby state:
The state of the manipulator is shown in Figure 3-3 when the driver is in standby state. The
LED digital tube default display
and check or modify parameters.

. At this point, user may press

to enter menu items,

GS DRIVER

Figure 3-2 Power-on initialization state

CTB

Figure 3-2 Standby state

Operating state:
The driver enters operating state after receiving correct operation command in standby
state. As shown in Figure 3-4, the LED digital tube default displays the set speed of the
driver, e.g F. 1500. In this state, user may press

to enter menu items, and check or

modify parameters.

Fault alarm state

When fault is detected as the driver is in operating, standby or programming state, the
corresponding fault information will be displayed immediately as shown in Figure 3-5.
When a fault occurs, user may conduct drive reset by pressing

and

. If the

fault has disappeared, it returns to the standby state; if the fault still exists, the fault code
will be displayed again.

Figure 3-4 Operating state

Figure 3-5 Fault alarm state

GS DRIVER

CTB

Parameter transmission state:

Parameter initialization will be carried out within the driver after power-on initialization
every time. The driving returns to normal state after parameter download. In this process,
LED digital tube displays

all the time as shown in Figure 3-6.

Password state:
The manipulator will prompt to enter a password as shown in Figure 3-7 when entering
programming state from standby and operating state as An00=1. The password must be
entered correctly in the state before entering the programming state

Figure 3-6 Parameter transmission state

Figure 3-7 Password state

Use method of the manipulator

The section mainly introduces use of the manipulator, and basic operations of functions.

Parameter setting operation process

Parameter setting method of manipulator of 22315kw driver adopts three-level menu
structure. Parameter value of menu items can be checked and modified conveniently.
The three-level menu: menu item (1-level menu), parameter tem (2-level menu) and
parameter setting (3-level menu). The operation process is shown in Figure 3-8.

GS DRIVER

CTB
Figure 3-8 3-level menu operation flow chart

During operation in 3-level menu, user may return to 2-level menu by pressing

or

(see Figure 3-8 and Figure 3-9). The difference between the two operations: after press
ENTER key, the set parameter value will be saved to the controller, and then return to
2-level menu; it will return to 2-level menu directly without saving the parameter value by
pressing MENU. The detail operational procedures of 3-level menu are shown in Figure
3-9.

Modify the parameters with the manipulator

The flow chart of modify the parameters with the manipulator is shown in Figure 3-9.

Figure 3-9 3-level menu operation flow chart

Description:
Eight menu items are included in 1-level menu: Un menu, An menu, Bn menu, Cn menu,
Dn menu, Fn menu, Pn menu and In menu.
In 2-level menu, each group of parameter includes 48 parameters. Please see parameter
description for specific function.

GS DRIVER

CTB

User password function

To enhance reliability and security of parameter setting, manipulator of 22315kw driver
has user password function. The operating process is shown in Figure 3-10. Please refer to
An22 for modification of user password. The default password is: 00000.

Figure 3-10 User password function operation flow diagram

Monitor operating state with the manipulator

Operation state, interface state and fault information of the driver can be monitored
respectively through U1, U2 and U3 of the manipulator

Operation state monitoring

Operation state monitoring includes set speed F, output speed O, feedback speed b, output
current A, output torque T and DC bus voltage U of the driver. Please see Figure 3-11 for
monitoring method.

Figure 3-11 Driver operation state monitoring flowchart

Interface state monitoring

Interface state includes switching value input terminal U2-2/U2-3, switching value output
terminal U2-4, analog input interface U2-5/U2-6, U2-7/U2-8 and encoder input interface
U2-0/U2-1. The monitoring method is same with monitoring parameter, only needs to select
corresponding parameter in U2. Please see parameter table of parameter number.

GS DRIVER

CTB

Fault information monitoring

The control panel will display the current fault message code when the driver is in fault state.
The fault record of the driver can be checked through U3. The check operation is same with
monitoring parameter, only needs to select corresponding parameter in U3. Please see
parameter table of parameter number.

GS DRIVER

CTB

Test run
The chapter describes methods and precautions for initial test run of the driver
Basic procedure of test run..4-2
Confirmation of connection of the main circuit.4-2
Control circuit wiring confirmation..4-3
Initial power-on of the driver4-3
Motor and driver parameters confirmation4-4
No-load test run.4-4
Loaded test run..4-4

GS DRIVER
Basic procedure of test run

CTB

The initial power-on operation of the driver shall be carried out by the following procedures,
otherwise, accident, damage to equipment or other hazards are likely to happen.

Confirmation of the connection of the main circuit

Please confirm the following contents in connection of the main circuit
1. Connect the connecting wire on driver R / S / T to 3-phase power frequency power

GS DRIVER

CTB

supply. The voltage of the power supply shall meet the requirements of the drive.
2. The driver is equipped with built-in braking unit. The braking resistor is connected to P /
PB. Do not connect any connect wire to N terminal.
3. When the output terminal of the driver is connected to the motor, it shall by ensured that
their phase sequences are same, otherwise, he motor cannot operate normally, and prone
to burn the equipment. If shield cable is used for output cable, the shielding layer at the
ends of the cable shall be connected respectively to ground terminal of the drive and motor.
4. When filtering magnet ring is installed on the output line, it shall be close to the driver
side as possible. The shielding layer and ground line cannot pass through the magnet ting,
and the magnet ting cannot be in contact with the U / V / W terminal.
[Link] driver and motor must be well grounded.
6. Confirm all connecting wire are connected reliably.

Control circuit wiring confirmation

Please confirm the following contents for control circuit wiring and jumper
1. Confirm the terminal input state is connected correctly by the design requirements. NPN
mode shall be selected when output signal of the CNC system is 24V; PNP mode shall be
selected when output signal of the CNC system is 0V (by modifying Bn46).
2. It's prohibited to connect the high-voltage line to the control signal.
3. Analog signal input signal connecting line must use shielded cable. The shielded cable
shall be connected to housing of the connector.
4. When use 0 ~ 10V as speed set, confirm that the J2 jumper is plugged, and the j1 jumper
is unpluggd.
5. Cable for motor encoder shall use the standard cable provided by the manufacturer.
6. Connecting wire from encoder output to the CNC system must use shielded twisted pair
cable.
7. Confirm all control signals are connected firmly.
8. ST terminal is driver enabling. The driver cannot start work without input at ST.
Caution
The wire connection must be inspected carefully before initial power-on of the driver,
otherwise, it's prone to accidents

Initial power-on of the driver

The internal components of the driver may be damaged due to vibration and other reasons

GS DRIVER

CTB

during transportation or installation. The power-on process shall be observed carefully in

initial power-on to find problem and treat in a timely manner.

Power-on process of the driver and observation content

Motor and driver parameters confirmation

The default parameters of GS series servo driver shall be basically in conformity with the
practical application. Most of the parameters do not need modification. For initial application,
user shall modify or confirm part of the parameters as required.

Parameters need to be confirmed in test run

Initialization parameters: An, An-01, An-02, An-03.
Motor and driver parameters: Dn, Dn00 ~ Dn05, Dn10 Dn20.
Basic control parameters: Bn, Bn00 ~ Bn47.
Control relevant parameter-Cn, and modify as needed.
Relevant system parameter-Sn, and modify as needed.

No-load test run

Test run is carried out with default parameters: analog-10V ~ +10 V speed setting. The
process is as follows:
. Apply 1V voltage to FV-Fc, input enabling signal I0.
Monitor the following data:
The given speed U1-0 is displayed as 150. A few turns deviation is normal and can be
adjusted through parameter Cn
The feedback speed U1-2 is in conformity with the given speed.

GS DRIVER

CTB

Output current U1-3, deviation below 10% of rated current is normal.

Output torque U1-4, it's normal within 100.
Observe the following phenomenon:
Is the driver fan running?
Is the motor fan running?
Is the motor running smoothly?
Is there abnormal sound during motor operation?
Is surface temperature of the motor normal?
. Disconnect enabling signal
Observe the deceleration of the motor is normal or not.
Observe heating of braking resistor (braking unit) is serious or not?
. Increase speed continuously, and repeat the first and second step, and monitor
operation of the driver and motor. The equipment must be shutdown immediately for
inspection for any abnormalities, and contact with technical personnel of the manufacturer if
necessary.

Loaded test run

Attention shall be paid to the following contents during loaded test run of the driver:
1. Loading gradually from small to large. Please inspect or contact with the manufacturer
for over loading.
2. Monitor feedback speed, output current and output torque of the driver constantly during
loading; observe motor vibration and noise and temperature rise continuously. The
equipment shall be shutdown timely for any abnormalities.
3. To avoid accident, the motor shall be stopped before adjusting motor parameters. The
parameter regulating quantity shall not be too big.
4. Do not make overload test or destructive test to avoid burning of the driver and motor.
Caution
If the following situations occur, please shut down immediately and inspect, or contact the
manufacturer.
1. Major fluctuation of feedback speed, output current and output torque of the driver, or
reach the limit.
2. The motor operation is abnormal with abnormal vibration and noise.
3. Mechanical equipment abnormalities

GS DRIVER

CTB

Parameter list
The chapter describes all of parameters of the driver.
Parameter list description.5-2
Monitor parameter U15-2
Monitor parameter U25-3
Monitor parameter U3.5-3
Initialize parameter An5-3
Basic control parameter Bn...5-5
User parameter Cn..5-6
Motor drive parameter Dn..5-8
Function parameter Fn...5-9
Function parameter In.5-9
Protection parameter Pn5-10
System communication parameter Sn5-11

GS DRIVER

CTB

Parameter list description

Parameter list
Parameter code

Item

Page

U1

Running state monitoring

5-2

U2

Interface state monitoring

5-3

U3

Fault record

5-3

An

Parameter initialization

5-3

Bn

Basic control parameter

5-5

Cn

User parameter

5-6

Dn

Motor and driver parameter

5-8

Fn

Special program function parameter

5-9

In

Special program position function parameter

5-9

Pn

Protection parameter

5-10

Sn

Communication function parameter

5-11

1. The contents of the parameter list are described as follows:

Function code:

code of parameter group and parameter number;

Name:

Setting range:

name of the parameter;

detailed description about function and effective setting value of the
parameter;
the range of effective setting value of parameter;

Unit:

parameter setting unit;

Factory setting:

original factory parameter setting;

parameter changing properties (ie, allow changing or not and change
condition) are as follows:
"": indicates the setting of the parameter may be changed in shutdown,
operating state of the driver;
"": indicates the setting of the parameter cannot be changed in
operating state of the driver;
"-": indicates changing of setting of the parameter by user is prohibited;
"*": indicates the value of the parameter actually measured value, and
cannot be changed.

Description:

Change:

Monitoring parameter U1
Operation: press on the control panel to select the corresponding function code in
operating state to monitor.

GS DRIVER

CTB

Function
code

Name

Set speed/frequency

Output speed/ frequency

Description

Unit

Speed : rpm
Frequency: Hz

Feedback speed/ frequency

Speed is displayed with maximum

speed8000rpm;frequency is
displayed with maximum
speed10000rpm

Driver output current

Actual feedback torque of the

motor

Range: -3276732767

n.m

Driver DC bus voltage

DC bus voltage =AC power voltage

x1.4

GS DRIVER

CTB

Monitoring parameter U2
Operation: press

to enter U2, and press

Function code

and

to select appropriate function code to monitor.

Name

Description

Setting range

Unit

U2-00

Motor encoder count value

4 frequency multiplication counting

PULSE

U2-01

4 frequency multiplication counting as encoder input.

External input encoder PULSE
2 frequency multiplication counting as single PULSE input, 1
input count value
frequency multiplication counting as double PULSE input.

PULSE

U2-02

Switching value I1-I6 ST input

state

U2-03

Internal switching value IA-ID

input state

U2-04

Switching value output state

MIA/MOA/Q2-Q1

U2-05

Analog input FI channel digital Analog quantity

(analog) switching
Digital quantity

0+10V

U2-06

Analog input FV channel digital Analog quantity

(analog) switching
Digital quantity

-100+10V

U2-07

Analog input FT channel digital Analog quantity

(analog) switching
Digital quantity

U2-08

Multifunction analog input

0100%

U2-09

Module temperature

Driver power module temperature display

U2-10

Driver temperature

Display temperature of inside of the driver

U2-11

Accurate
monitoring

09999

PULSE

stop

of

0100%
-100%0100%
-100+10V
-100%0100%

deviation Adjust stop position of the motor

GS DRIVER
Monitor parameter U3
Operation: press

CTB

to enter U3, and press

Function code

Name

U3-0

and

to select appropriate function code to monitor.

Description

Set range

Unit

Factory setting

Modification

Current fault code

U3-1

last 1st fault code

U3-2

last 2nd fault code

U3-3

last 3rd fault code

U3-4

last 4th fault code

U3-5

last 5th fault code

See fault description for detail (Chapter 7)

Initialization parameter An
An parameter list
Function
code

An00

Name

Description

Set range

Unit

Factory setting

Modification

parameter
password
protection

0: HP password invalid
1: HP password valid
User needs to enter password to enter An, Bn, Cn,
Dn, Fn, In, Pn and Sn.
The initial password is input digital value. The factory
value is 0.

01

GS DRIVER
Function code

An01

An02

CTB
Set range

Unit

Factory
setting

Modification

04

032767

032767

0,1

Set time that needs timing

032767

Name

Control mode selection

Driver power

Description
Select driver motor control mode
0: induction motor V/F control
1: induction motor open loop vector control
2: induction motor servo driver
3: magneto inductor open loop vector control
4: magneto inductor servo driver
1.1Kw:0018

18.5kw:0145

110kw:0168

1.5Kw:0020

22kw:0145

132Kw:0164

2.2Kw:0050

30kw:0146

160kw:0165

3.7kw:0051

37kw:0146

185Kw:0177

5.5kw:0052

45kw:0148

200Kw:0193

7.5kw:0116

55kw:0151

250Kw:0179

11kw:0120

75kw:0150

300Kw:0184

15kw:0121

90Kw:0162

An03

Motor model selection

See Appendix 1

An04

Software version number

Factory software version number 2.00

An05

Driver encoder selection

0: encoder 1 port
1: encoder 2 ports

An06

Timing time setting

An07

Driver power-on time

Monitor accumulated power-on time of the driver

065535

An08

Driver operating time

Monitor accumulated operating time of the driver

065535

An09

Parameter changing is
allowed

0.1

0: Parameter changing is not allowed during operating of

the driver.
1: Parameter changing is allowed during operating of the

GS DRIVER

CTB
driver

An10

Control program selection

An11

Control program version

number

An12

Encoder 1 port interface

type

An13

Encoder 2 ports interface

type

An14

Encoder interface filtering

time

An15

carrier wave frequency

selection

0: standard program
1: special program

0.1

Control program version number

J000

0: no encoder card
1: increment TTL encoder card
19: rotary transformer interface card
14: SIN/COS interface card
The other are reserved

ms

KHz

00.5

34

632

11

48

764

22

516

8128

02

28

416

14

312

9256

An16

Save

An19
An20

Timing function valid

0: invalid. 1: valid

An21

Timing function valid

password

Set password to accurate time function. Generally, An20

can only be modified with the value is same with An22

An22

Timing function password

setting

To set initial password of timing function

GS DRIVER
Function code

CTB
Name

Description

Set range

Unit

Factory setting

Modification

Manufacturer
special

An23

An47

Basic control parameter Bn

Bn parameter list
Function code

Name

Description
0: terminal operation
2: communication operation
1: control panel operation

Set range

Unit

Factory setting

Modification

0.2

Bn00

Control mode

Bn01

Operation
command 0: operation + direction I1: operation signal I2: direction signal
mode selection
1: forward/reverse I1: forward signal I2: reverse signal

0.1

Bn02

Analog quantity mode

0: bipolar (10V10V) 1: unipolar (010V)
selection

0.1

Bn03

Positioning
selection

mode 0: motor built-in coded disc

1: spindle encoder

0.1

Bn04

Accurate stop
mode selection

signal 0: accurate stop electrical level valid

1: accurate stop PULSE valid

0.1

Bn05

Motor rotate direction

0.1

Bn06

Reverse
forbidden

rotation 0: invalid
1: valid

0.1

Bn07

Machine

type 0: milling

0.1

tool

0: anticlockwise is forward
1: clockwise is forward

GS DRIVER

CTB

selection

1: turning

Bn08

Speed search in start

0: invalid
1: valid

0.1

Bn09

Stop mode

0: decelerated stop
1: free stop

0.1

Bn10

Emergency stop mode

0: decelerated stop
1: free stop

0.1

Bn11

Emergency
stop 0: inspect
low-voltage inspection 1: do not inspect

0.1

Bn12

Save

Bn13

Accurate
selection

mode 0: accurate stop according to current speed

1: reverse rotation accurate stop

0.1

Bn14

Accurate stop direction 0: forward rotation accurate stop 1: reverse rotation accurate
selection
stop

0.1

Bn15

I1 terminal
definition

0.1

Function code

function 0: analog speed control

1: PULSE speed control

Name

Description

Set range

Unit

Factory setting Modification

0.1

Bn16

PULSE mode selection

0: direction +PULSE
CW/CCW
1: 90orthogonal PULSE

2:

Bn17

High speed mode selection

0: common mode
1: high speed mode

0.1

Bn18

High-accuracy mode

0: common mode
1: high-accuracy mode

0.1

Bn19

I4 terminals function definition

0: analog position control

1: PULSE position control

0.1

GS DRIVER
Bn20
Bn21
Bn22
Bn23

CTB

Terminal Q1 output function selection

0: no output
4: driver fault 1: output
5: speed
Terminal Q2 output function selection in all time
reached 2: driver in operation 6: 0 speed
Terminal MOA output function selection operation 3: driver ready
7: accurate
stop reached 8: torque alarm point output
Terminal M1A output function selection

09

0.1

07

Bn24

Save function

Bn29

Bn30

Multifunction
selection

terminal

I5

0: invalid
3: 0 speed function
function 1: second accurate stop function
external fault input
2: low-speed function

4:

Bn31

Save function

Bn44
Bn45

Operation panel control motor rotation

0: forward
direction selection

Bn46

I/O electrical level selection

0: PNP

Bn47

Control enabling

0: terminal control enabling

control enabling

1: reverse
1: NPN

User parameter Cn
Cn parameter list

1: internal

GS DRIVER
Function code

CTB
Name

Description

Set range

Unit

Factory setting

Modification

To adjust symmetry of analog against 0 point

04096

-2020

0.1

PULSE

PULSE

Cn00

Save

Cn01

Analog 0 forward deviation

Cn02

Analog 0 reverse deviation

Cn03

Analog gain

Actual speed setting=analog sampling value X

Cn03

Cn04

Accurate stop offset

Set position offset against 0 point during

accurate stop

Cn05

Second accurate stop offset

Cn06

Accurate stop
speed ring gain

Cn07

Accurate stop speed

Cn08

Constant power
point frequency

Cn09
Cn10
Cn11

04 times
encoder line
Set position offset against 0 point during
number
second point accurate stop

positioning

To adjust rigidity during [positioning

132767

500

Find speed of Z phase PULSE of encoder

during accurate stop

11000

rpm

300

breaking breaking point frequency when motor enters

constant power

010000

0.01Hz

50.00

S curve time in speed control S curve time in speed control

05.00

0.01S

Maximum output speed

18000

rpm

8000

0 offset compensation
speed control

Corresponding speed when input 10V analog

When speed command input is 0, offset of

in speed command analog can be eliminated
-10%10%
through the parameter to make the motor speed
zero.

GS DRIVER
Function code

CTB
Name

Description

Set range

Unit

Factory setting

Modification

0300

Cn12

Spindle acceleration time

Set acceleration time of spindle acceleration
during speed control

Cn13

Set speed ring adjuster proportional gain during

Speed ring proportional speed control. The gain and rigidity are higher with
gain during speed control greater setting value. Please set the value as small
as possible without vibration generated in the system.

032767

100

Cn14

Set speed ring adjuster integration time constant

Speed ring integration during speed control. The integration speed and
time
constant
during rigidity are higher with smaller setting value. Please
speed control
set the value as small as possible without vibration
generated in the system.

032767

500

Cn15

Set speed ring adjuster integration time constant

Speed control 0 speed
during speed control. The gain and rigidity are higher
proportional gain
with greater setting value.

132767

100

Cn16

Speed control current

Set current loop proportion during speed control
loop proportional gain

1150

80

Cn17

Speed control current

Set current integration time during speed control
integration time constant

1150

ms

80

Cn18

Analog input filter time

Adjust sampling time of analog input port
constant

06

Cn19

External
number

032767

PULSE

1024

Cn20

Rigid tapping maximum

Set the maximum speed of rigid tapping
speed

03000

rpm

1500

Cn21

Rigid tapping (PULSE Set speed ting adjust proportional gain during rigid
position) control 0 zero tapping (PULSE position) control zero speed. The
speed proportional gain
gain and rigidity are higher with greater setting value.

132767

100

Cn22

Rigid tapping (PULSE Set acceleration time of motor from 0-1000 rpm when
position) acceleration time the spindle is in rigid tapping / PULSE position.

0300

encoder

line

Output PULSE number per turn of external encoder

GS DRIVER

CTB

Cn23

Rigid tapping (PULSE Set deceleration time of motor from 0-1000 rpm when
position) deceleration time the spindle is in rigid tapping / PULSE position.

0300

Cn24

Set position ring adjuster proportional gain during

position control. The gain and rigidity are higher with
PULSE position control
greater setting value, and the position lagging is
position ring proportional
smaller with same frequency command PULSE,
gain
however, the too small value may cause vibration or
over control.

032767

500

Cn25

Set speed ring adjuster proportional gain in speed

Rigid tapping (PULSE
control. The gain and rigidity are higher with greater
position)
speed
ring
setting value. Please set the value as big as possible
proportional gain
without vibration generated in the system.

032767

100

Cn26

Set speed ring adjuster integration time constant in

Rigid tapping (PULSE
speed control. The gain and rigidity are higher with
position)
speed
ring
smaller setting value. Please set the value as small
integration time constant
as possible without vibration generated in the system.

032767

500

Cn27

Rigid tapping (PULSE S curve time during rigid tapping (PULSE position)
position) S curve time
control

05.00

0.01s

Cn28

Rigid tapping (PULSE

Set current ring proportion during rigid tapping or
position)
current
ring
PULSE position
proportional gain

1150

80

Cn29

Rigid tapping (PULSE

Set integration value of current ring during rigid
position)
current
ring
tapping or PULSE position
integration time

1150

80

Cn30

Speed
deceleration time

0300

Cn31

Output torque limit

01000

0.2%

1000

Cn32

PULSE
multiplying
numerator

command
Set multiplying power numerator
power
command PULSE (electronic gear)

132000

1000

Cn33

PULSE
multiplying

command Set multiplying power denominator of position

power command PULSE (electronic gear)

132000

1000

control Set deceleration time of motor from 0-1000 rpm when

the spindle is in speed control.
Set maximum output torque of the driver
of

position

GS DRIVER

CTB

denominator
Cn34

PULSE
command
0: normal
direction reverse

Cn35

Conduct smoothing filtering to PULSE order. It's

PULSE
specified
mainly used at field with greater PULSE command
smoothing filtering time
fluctuation.

Cn36

0 speed reach range

Cn37

PULSE position control

Set precision range in positioning
precision range

Function code

1: PULSE command direction reverse

Set standard of 0 speed reaching. Output 0 speed

signal when output speed is lower than the set value.

Name

Description

09

032767

rpm

100

032767

PULSE

Set range

Unit

Factory setting

Modification

032767

PULSE

Cn38

Accurate stop reach range

Cn39

Torque alarm point threshold

Set torque limit value
level

0327

Nm

Cn40

Swing speed

Set swing speed

03000

rpm

300

Cn41

Positive
direction
amplitude

swing

Set the maximum angle of positive swing

032767

PULSE

300

Cn42

Negative
amplitude

swing

Set the maximum angle of negative swing

0 32767

PULSE

-300

Cn43

Swing
time

control

acceleration Set acceleration of motor from 0 to the set

speed during swing control of spindle

0300

Cn44

Swing
time

control

deceleration Set deceleration of motor from the set speed

to 0 during swing control of spindle

0300

Cn45

Swing torque limit

Set the maximum output torque of the driver

during swing

01000

Nm

20

Cn46

Multifunctional
maximum speed

08000

rpm

400

direction

Set positioning precision range

01

terminal Define
the
speed
setting
multifunctional terminal I6

value

of

GS DRIVER
Cn47

CTB

0: standard acceleration and deceleration curve

(line)
Acceleration and deceleration 1: acceleration and deceleration curve in fixed
curve selection
time (without S curve function)
2: acceleration and deceleration curve in fixed
time (with S curve function)

02

Motor driving parameters Dn

Dn parameter list
Function code

Name

Dn00

Rated power

Dn01

Description

Motor mode

Set range

Unit

Factory setting

Modification

Set rated output power of motor

M,S

0110

kw

Rated voltage

Set rated output voltage of motor

0460

380

Dn02

Rated current

Set rated output current of motor

M,S

0300

Dn03

Rated frequency

Set rated output frequency of motor

M,S

0500

Hz

50

Dn04

V/F Rated power

Set V/F Rated power

032767

Hz

50

Dn05

Rated speed

Set rated output speed of motor

M,S

015000

rpm

1460

Dn06

Rated torque

Set no-load current of motor

M,S

0300

M,S

0100

0.01

Dn07

Insulation resistance Set insulation resistance

between conductors conductors of motor

Dn08

Inductance between Set reactance between conductors of

conductors
motor

M,S

mH

Dn09

Inversion
1000 rpm inversion electromotive force
electromotive force EMK

M,S

10010000

1024

01

Dn10

Encoder line number

Dn11

Encoder counting

between

Set physical encoder line number of one

turn of motor
0: forward

1: reverse

GS DRIVER

CTB
direction

Dn12

0 speed current

Dn13

Maximum torque

Dn14

Dn15

Function code

Motor 0 speed current

M,S

032767

M,S

Motor parameter
self-matching

0: invalid
1: preset according to control parameters
of motor. Take set steady voltage or
frequency transformer voltage level as
input voltage.
2: preset according to control parameter
2
of motor. Take DC bus voltage
measured during power-on as input
voltage .

M,S

02

Encoder position
self-matching

Position self correct of encoder and

motor magnetic pole
0: invalid
1: self correct

01

Name

Description

Motor mode

Set range

Unit

Factory setting Modification

Dn16

Motor self-learning

Motor parameter self-learning

0: invalid
1:motor induction electromotive
force
2: motor inductance
3: motor stator resistance
4: motor rotor resistance
5: reserve
6: reserve
7:automatic self-learning (static)
8: automatic self-learning (rotary)

M.S

015000

rpm

1460

Dn17

Weak magnetic speed

GS DRIVER

CTB

Dn18

Magnetic flow weakening factor

Dn19

Weak magnetic curve

Dn20

Driving panel module current

Dn21

Driving panel power

Dn22

DBVD calibration value

Dn23

CVD calibration value

Dn24

Module temperature calibration

value

Dn25

Radiation fin temperature

calibration value

Dn26

Hall sensor calibration value

Dn27

Test date

Dn28

Checker No.

Dn29

Driving panel model

Dn43Dn47

Reserve function

Reversed by manufacturer

Special program function parameter Fn

Fn parameter list
Function code

see appendix for detail parameter

Name

Description

Set range

Unit

Factory setting

Modification

Reserve function

Fn00

Fn70

Special program function parameter In

GS DRIVER

CTB
In parameter list

Function code

Name

Description

see appendix for detail parameter

Set range

Unit

Factory setting

Modification

In00

Reserve function

In47

Protection parameter Pn
Pn parameter list
Function code

Name

Description

Set range

Unit

Factory setting

Modification

Pn00

Bus voltage
inspection and alarm

0: valid, real time monitor bus voltage

Report OV1 when it's greater than Pn01. Report UV1 when it's
smaller than Pn02.
1: invalid. Inspect bus voltage but do no alarm

0.1

Pn01

DC bus overvoltage Set alarm value of DC bus overvoltage (bus voltage = AC voltage
alarm point
x1.4)

0800

800

Pn02

DC bus under voltage Set alarm value of DC bus low voltage (bus voltage = AC voltage
alarm point
x1.4)

0800

400

02

Pn03

Low voltage
inspection and alarm

0: valid. Alarm UV1 with signal input

1: invalid
2: report UV when low voltage time is longer than set value of
Pn04.

Pn04

Instant low voltage

alarm time

Valid when Pn03=2

01000

1ms

10

Pn05

Motor thermal
protection mode

0: N.C. type
1: N.O. type
2: invalid

0.1.2

GS DRIVER

CTB

Pn06

Instant power turn-off

inspection

0: alarm. Output P OFF signal

1: motor dose not power-on. Do not alarm
2: Alarm after exceeding the alarm time

02

Pn07

Instant power-off
inspection time

Set alarm time of instant power-off. Output P OFF alarm when

power-off time exceeds the set value.

01000

ms

10

Pn08

Power phase lack

inspection

0: alarm PL
1: prompt alarm, display PL, do not affect operation
2: do not alarm

02

Pn09

Over current alarm

point

Set motor over current alarm value (percent of rated current)

0200

150

Pn10

Reserve function

Pn11

Reserve function

Pn12

Reserve function

Pn13

Reserve function

02

Pn14

Radiating fan control

0: run as power-on of driver

1: run with output of driver. And stop after set time in time-delay
Pn 15 after driver stops.
2: operate according to temperature of radiating fin and module:
Operate: radiating fin temperature >4 and module
temperature >55
Stop: radiating fin temperature<304 and module temperature
<45

Pn15

Fan time-delay stop

time

Set fan time-delay stop time (valid with Pn14=1)

0100

10

Pn16

Alarm reset mode

0: manual reset with ENTER or RET

1: automatic reset. The alarm is reset after alarm signal
disappears

0.1

Pn17

Anti-stall function in
acceleration and

0: invalid, operate by the set acceleration and deceleration time

1: operate by the set acceleration to prevent over-current alarm

0 65535

GS DRIVER

CTB
deceleration

due to short acceleration time

2: operate by the set deceleration to prevent over-voltage alarm
due to short deceleration time
3: reserve
4: operate by the set deceleration to prevent over-current alarm
due to short deceleration time

Pn19

Function code

Name

Description

Set range

Unit

Factory setting

Modification

Pn20

Motor encoder under-phase

inspection start frequency

Motor shaft encoder under-phase inspection start

frequency

0255

HZ

Pn21

Encoder under-phase
inspection allowed time

Motor shaft encoder under-phase allowed time

050

65ms

Pn22

Encoder 0 bit inspection

0.1

0: inspect

1: do no inspect

Pn23

Reserve function

Pn29
Pn30

Encoder no feedback alarm

setting

0: invalid 1: valid

0.1

Pn31

Reserve alarm setting

0: invalid 1: valid

0.1

Pn32

Z phase lack setting

0: invalid 1: valid

0.1

Pn33

Encoder line number error

alarm setting

0: invalid 1: valid

0.1

150

01

Pn34

Pn40

Reserve function
Power-off protection function

0: invalid 1: valid

GS DRIVER
Pn41

Pn47

CTB

Power-off protection braking

torque

Set Power-off instant braking torque

Reserve function

0100%

85

Factory setting

Modification

System communication parameter Sn

Sn parameter list
Function code

Name

Register No.

Description

Set range

Unit

07

Baud rate:
Sn00

Baud rate

300

0300bPS

1600bPS

21200bPS

32400bPS

44800bPS

59600bPS

619200bPS

738400bPS

Sn01

Data format

301

0: no calibration 1: even parity 2: odd parity

02

Sn02

Local host address

302

Station number: 1247.0 is broadcast address

0247

Sn03

Answer delay

303

Answer delay 020ms

020

1ms

Sn04

Accumulation
exceeding time

304

Accumulation exceeding time 0.060.0s

060

0.1ms

Sn05

Command terminal

305

08

Sn06

Control function

306

bit0Invalid
bit4i4

bit1i1 bit2i2
bit5i5

bit0Enabling

bit3i3

bit6i6

bit1reset

bit2run / stop 0: stop 1: run

bit3forward /reserve 0: forward 1: reserve
bit4i4
bit5i5
bit6i6

Parameter set selection 0-7

GS DRIVER

CTB
bit7Reserve

Function code

Name

Register No.

Description

Set range

Unit

Factory setting

Modification

bit8Quick stop and start

bit9Return to reference point
bit10Start positioning
bit11Reserve
Sn06

Control function

306

0: Standard mode

bit12
Mode
selection
bit13

4096: synchronous mode

8192: position mode
12288: reserve

Sn07

Control terminal
state display

307

Sn08

Control function
state display

308

Sn09

Command speed
setting

309

For speed command setting val during

communication control

Sn10

Actual speed

310

Display actual speed of motor operation

Sn11

Positioning target
value

311

For position command setting value during

communication control

Sn12

Sn47

Reserve

GS DRIVER

CTB

Set parameter by function

The chapter helps user for parameter setting and debugging by function of use
Spindle control timing sequence state diagram.6-2
Motor basic parameters setting.6-2
Motor operating parameters..6-3
Operation panel operation.6-3
Analog quantity speed control..6-3
Acceleration and deceleration control parameters6-5
Accurate stop parameters..6-6
Rigid tapping.6-7
PULSE control..6-8
Swing control..6-9
Multi-function terminal control.6-10

GS DRIVER

CTB

Spindle control timing sequence state diagram

Analog interface control timing sequence
Please control input of GS driver by the following timing sequence when spindle is
controlled by the CNC system through analog interface.

Function

Description
I1

I2

I3

I4

I5

I6

FV/FI

Forward

Reverse

Accurate stop
positioning

Accurate end M10-M1 output

Rigid tapping /C
shaft

Analog or PULSE with bipolarity

Spindle swing

Y/N

Swing speed is determined by the

parameters

Multifunction

The functions may be defined

separately

RET PULSE greater than 100ms

Reset

ST

I1 may not be connected when

analog is of bipolarity

PULSE interface control timing sequence

Standard PULSE interface is provided by GS driver when spindle is controlled by the CNC
system via PULSE interface. GS driver also provides PULSE speed control and PULSE
position synchronization function. Please see the following table for control timing
sequence.

Function

Description
I4

I1

Terminal function de

Parameter

PULSE position
synchronization

Realize PULSE position synchronization control,

for rigid tapping and C shaft and other functions

Bn19=1

PULSE speed
synchronization

Realize PULSE speed synchronization control, for

normal spindle speed control

Bn 15=1

Note: 1.1 with input signal; 0 no input signal; regardless of input signal state.
2. Y need analog input; N does not need analog input.
3. If rigid tapping uses PULSE signal, I4 does not need to be controlled, and I4 terminal
function shall be connected.

GS DRIVER

CTB

4. If speed control uses PULSE signal, analog terminal does not need to be connected, and
I1 or I4 control signal shall be connected.

Motor basic parameter setting

Please set the following parameters correctly before operating according to the motor

Function

Name

Description

Set range

Unit

Factory
setting

Modifica
tion

0315

kw

Dn00

Rated power Set rated output power of motor

Dn01

Rated voltage

Set rated output voltage of

motor

0460

380

Dn02

Rated current

Set rated output current of

motor

0300

Dn03

Rated
frequency

Set rated output frequency of

motor

0500

Hz

50

Dn04

V/F rated
frequency

Set V/F rated frequency

0500

50

015000

rpm

1460

Dn05

Rated speed Set rated output speed of motor

Dn06

Rated torque

Set no-load current of motor

0300

Dn10

Encoder line
number

Set encoder line number of

motor

10010000

1024

Motor operating parameter

Cn13 Speed control proportional gain during speed control: speed ring adjuster
proportional gain when setting speed control. The gain and rigidity are higher with greater
setting value. Please set the value as small as possible without vibration generated in the
system.
Cn14 Speed integration time constant during speed control: speed ring adjuster integration
time constant when setting speed control. The interface time is faster and rigidity is higher
with smaller setting value. Please set the value as small as possible without vibration
generated in the system.
Cn15 Speed control 0 speed proportional gain: speed ring adjuster proportional gain when
setting speed 0 speed control. The gain and rigidity are higher with greater setting value.
Speed control current loop proportional gain: current gain in rated speed.
Cn17 Current integration time constant during speed control: current gain in rated speed.

GS DRIVER

CTB

Operation panel operation

The method of operation is as follows:
Modify the parameter, make Bn00 = 1 and confirm.
Press RUN on the panel to make driver power-on.
In F 0000 menu, press ENT on the panel to enter data input state, press , >> on the
panel to enter the required speed, and press ENT or >> to start the motor.
Press STOP or >> to make motor decelerate and stop.
The 3rd step may be repeated at any time during operating of the motor to change
operating speed of the motor. User may change motor operating direction during operating
through FWD/REV direction command on the panel or modify parameter Bn45.

Caution Operation panel operation is a simple operation mode, and generally used
for test. It's recommended that the motor speed shall not set too high for operation panel
operation.

Analog speed control

Function
code

Name

Description

Set
range

Unit

Factory Modificatio
setting
n

Bn01

Operating
command mode

0: enabling + direction
1: forward / reverse

0.1

Bn02

Analog mode
selection

0: bipolarity(10V10V)
1: unipolarity(420mA010V)

0.1

Bn05

Motor operating
direction

0: anticlockwise for forward

1: clockwise for forward

0.1

When setting Bn01 and Bn02, they shall be selected according to control logic and analog
output mode of the CNC system. The timing sequence is as shown below:
Bn01 = 0, Bn02 = 0:

Forward timing sequence diagram

GS DRIVER

CTB

Reverse timing sequence diagram

Bn010Bn021:
Forward timing sequence diagram

Reverse timing sequence diagram

Bn011Bn021:
Forward timing sequence diagram

Reverse timing sequence diagram

Relevant parameters of analog speed setting

Function
code

Name

Cn01

Analog 0 point
positive offset

Cn02

Analog 0 point
negative offset

Cn03

Analog gain

Cn10

Maximum
output speed

Factory Modific
setting ation

Description

Set range

Unit

To adjust symmetry of analog

against 0 point

04096

Adjust speed offset due to analog

offset

0100

1%

115000

rpm

8000

Bipolarity:
Cn11

Cn18

0 point offset
setting in speed
control

0 point offset speed

Cn11Cn10/2046
Unipolarity:

-10%10% 0.1%

0 point offset speed

Cn11Cn10/4092

Analog input
filtering time
constant

Analog input parameter curve graph

06

GS DRIVER

CTB

Note on parameter setting:

Cn03: set analog gain, 1000 corresponds to 100 to adjust speed offset.
Cn11: for interference to analog when suppress command speed is 0. The speed setting
value is 0 when analog signal is lower than the setting value of the parameter.
Cn18: set analog input filtering time. The speed fluctuation may be too fast due to small
setting, and make spindle vibrate. Setting value set too much may affect speed response of
the spindle.

Acceleration and deceleration control parameters

Acceleration and deceleration control curve

GS driver acceleration and deceleration control curve

Acceleration and deceleration control parameters

GS DRIVER
Function
code

Cn47

CTB

Name

Description

0: standard acceleration and deceleration

curve (oblique line)
Acceleration and
1: acceleration and deceleration curve in
deceleration
fixed time (without S curve function)
curve selection
2: acceleration and deceleration curve in
fixed time (with S curve function)

Set
range

Unit

02

Factory Modificat
setting
ion

Cn09

S curve time in
speed control

S curve time in speed control

05.00 0.01S

Cn12

Spindle
acceleration time
in speed control

Set spindle acceleration time

0300

Cn30

Deceleration
time in speed
control

Deceleration time of spindle from 1000

0300
0 rpm in speed control

Accurate stop parameter

Function
code

Name

Description

Set range

Unit

Bn03

Positioning
encoder
selection

0: motor spindle encoder positioning

1: external shaft encoder positioning

0.1

Bn04

Accurate stop
signal mode

0: acceleration stop high electric level

valid
1: acceleration stop PULSE valid

0.1

Cn04

Accurate stop
offset

Set position offset against 0 point at

accurate stop

Cn05

Second point
accurate stop
offset

Cn06

Accurate stop
positioning
speed ring
positioning gain

To adjust rigidity in positioning

032707

1000

Cn07

Accurate stop
speed

Fine Z-phase PULSE speed of

encoder at accurate stop

01000

rpm

300

Cn37

Accurate stop
reach range

Set positioning precision range

032767

PULS
E

04
timeshare PULS
encyclope
E
Set position offset against 0 point at
dia line
second accurate stop
number

Accurate stop process curve graph

Factory Modificat
setting
ion

GS DRIVER

CTB

Accurate stop process curve graph

Control timing sequence

Bn03: set as 0: motor encoder positioning, for transmission ratio 1:1.
1: external encoder positioning, for spindle with transmission ratio other than 1:1. Intall
spindle positioning of the spindle encoder onto the spindle. At the same time, output
PULSE number per turn of Cn19 spindle encoder shall be set. The spindle encoder shall be
connected to T4 plug of the driver.
Note: If external encoder positioning is used, the spindle must rotate one round after
power-on of the driver and prior to first positioning.
Bn04: accurate stop signal mode;

0: acceleration stop high electric level valid

(recommended). Timing sequence is as shown in the following figure:

1: accurate stop PULSE is valid. The mode only can be used by input signal again to lift
locking of the motor.

GS DRIVER
Parameter settings note

CTB

Cn06: positioning gain in accurate signal stop. The parameter sets deceleration gain during
spindle accurate stop positioning. The positioning is slow if the value is too small, and
positioning accuracy may by affected or cause shock to the spindle if it's too great.
Cn07: spindle accurate stop speed. The parameter sets speed of finding encoder Z phase
at the start second of spindle positioning. The set value will affect speed and accuracy of
positioning of spindle.
The above two parameters are usually not recommended to modify by user.

Spindle accurate stop position setting

Manual adjustment:
1: The spindle shall perform one accurate stop firstly, and then release.
2: Rotate motor or spindle manually to position of accurate stop.
3: Observe value in menu U2-11, and then fill it in Cn04.
4: For small deviation at accurate stop position, it may be adjusted manually on the basis of
Cn04 value.

Rigid tapping
Function
code

Name

Cn01

Analog 0 point
positive offset

Cn02

Analog 0 point
negative offset

Cn03

Factory Modifica
setting
tion

Description

Set range

Unit

To adjust symmetry of analog

against 0 point

04096

Analog gain

Actual speed setting =analog

sampling value X Cn03

11500

0.1%

1000

Cn20

Rigid tapping
maximum speed

Set maximum speed of rigid

tapping

03000

Cn21

Rigid tapping
(PULSE position)
control 0 speed
proportional gain

Cn22

Rigid tapping
acceleration

rpm

1500

Set speed ring adjuster

proportional gain during rigid
tapping (PULSE position ) 0
132767
speed control. The gain and
rigidity is higher as the set value
is greater.

100

Set spindle acceleration during

030000
rigid tapping

0.05Hz/s

5000

Control timing sequence

When use analog as speed setting, and I4 input signal is valid, the timing sequence is as
follows as the spindle enters rigid tapping state.

GS DRIVER

CTB

Note on rigid tapping

1. To adapt to the rapid response and control accuracy of the spindle, the driver will
automatically adjust the relevant parameters of the control after entering rigid tapping state.
2. During rigid tapping, the spindle participates interpolation control of coordinate axis as a
position axis. At the moment, it's required that the CNC system shall switch control of
spindle to position axis control.
3. During rigid tapping, the maximum speed of the CNC system shall be consistent with
maximum speed of the driver, and analog voltage shall be adjusted to be symmetrical to 0V
through driver or the CNC system.

PULSE control
Function
code

Name

Bn16

PULSE mode
selection

Set
Factory Modificati
Unit
range
setting
on

Description
0: direction +PULSE
CW/CCW
1: 90orthogonal PULSE

2:
0

0
300

Bn22

Rigid tapping
Set acceleration time of motor from 0-1000
(PULSE position) rpm when the spindle is in rigid tapping /
acceleration time
PULSE position.

Cn21

Rigid tapping
Set speed ting adjust proportional gain
(PULSE position)
1
during rigid tapping (PULSE position)
control 0 zero
control zero speed. The gain and rigidity are 32767
speed
higher with greater setting value.
proportional gain

100

Cn23

Rigid tapping
Set deceleration time of motor from 0-1000
(PULSE position) rpm when the spindle is in rigid tapping /
deceleration time
PULSE position.

Cn24

Set position ring adjuster proportional gain

during position control. The gain and rigidity
PULSE position
are higher with greater setting value, and
0
control position
the position lagging is smaller with same
ring proportional
32767
frequency command PULSE, however, the
gain
too small value may cause vibration or over
control.

500

Cn25

Set speed ring adjuster proportional gain in

Rigid tapping
speed control. The gain and rigidity are
0
(PULSE position)
higher with greater setting value. Please set
speed ring
32767
the value as big as possible without
proportional gain
vibration generated in the system.

100

0
300

GS DRIVER

CTB

Cn26

Set speed ring adjuster integration time

Rigid tapping
constant in speed control. The gain and
0
(PULSE position)
rigidity are higher with smaller setting value.
speed integration
32767
Please set the value as small as possible
time constant
without vibration generated in the system.

Cn27

Rigid tapping
(PULSE position)
S curve time

S curve time during rigid tapping (PULSE

position) control

Cn28

Rigid tapping
(PULSE position)
current ring
proportional gain

Cn29

Rigid tapping
(PULSE position)
current ring
integration time

500

0
5.00

0.01
s

Set current ring proportion during rigid

tapping or PULSE position

1
150

80

Set integration value of current ring during

rigid tapping or PULSE position

1
150

80

Cn32

PULSE command
Set multiplying power numerator of position 32000
multiplying power
command PULSE (electronic gear)
~3200
numerator
0

1000

Cn33

PULSE command
1
Set multiplying power denominator of
multiplying power
position command PULSE (electronic gear) 32000
denominator

1000

Control mode selection

As shown in Table 6-1, function selection may be carried out through control signal when
using PULSE control mode and PULSE input.
Table 6-1 Control mode selection
Control terminal
I4
I1

Function
PULSE position control is for C shaft function, rigid tapping and other
accurate position control functions.
PULSE speed control is for applications in which spindle is used as
speed shaft.

GS DRIVER

CTB

Please see Table 7-2 for direction+

PULSE control interface. The control
timing sequence is shown in the right
figure.
Table 7-2 PULSE interface of CNC
system with GS series product
Control terminal

Function

SA+

PULSE+

SA-

PULSE-

Pb+

DIR+

Pb-

DIR-

Direction +PULSE input operating timing sequence diagram

Please see Table 7-3 for 90orthogonal

PULSE control interface. The control

90orthogonal PULSE operating timing sequence diagram

timing sequence is shown in the right

figure.
Table 7-3 PULSE interface of CNC
system with GS series product
Control terminal

Function

SA+

PA+

SA-

PA-

Pb+

Pb+

Pb-

Pb-

Swing control
Spindle swing is generally used for automatic shift of spindle system. Please see Cn40,
Cn41, Cn42 and Cn43 for spindle swing related parameters

Function
code

Name

Description

Set range

Unit

Cn40

Swing speed

Set swing speed

03000

rpm

Cn41

Positive swing
amplitude

Set the maximum angle of

positive swing

Cn42

Negative swing
amplitude

Set the maximum angle of

negative swing

032767 PULSE

Factory Modifi
setting cation
1500

100

0
32767

PULSE

100

Cn43

Swing control Set motor acceleration time when

acceleration time
the spindle in swing control

0300

Cn44

Swing control Set motor deceleration time when

deceleration time
the spindle in swing control

0300

GS DRIVER
Cn45

Swing torque limit

CTB
Set the maximum output torque
of the driver during swing

01000

nm

20

Control method
GS driver enters swing control function when the I6 terminal is valid; when signal of I6
terminal is canceled, spindle decelerates 0 speed, and maintain a free state.

Multi-function terminal control

Multi-function terminal I5 may select different control functions as required by user. The
function selection may be set through Bn30 parameters.

Second accurate stop function

Second accurate stop function is for second fixed point positioning as required by user.
Note: When second accurate stop is used, function of I5 will become the first, second
symbol selecting signal, at the same time, Cn05 will be taken as second accurate stop
position offset setting value.

Second accurate stop parameters

Function
code

Bn30

Name

Description

0: invalid
3: 0 speed function
Multifunction
1: second accurate stop function 4:
terminal I5
external fault input
function selection
2: low-speed function

Cn04

Accurate stop
offset

Set position offset against 0 point

during accurate stop

Cn05

Second accurate
stop offset

Set position offset against 0 point

during second point accurate stop

Set range

Unit

PULS
04
E
timeshare
encoder
PULS
line
E
number

Factory Modifi
setting cation

GS DRIVER

CTB

Timing sequence diagram

Low-speed function
Function
code

Name

Description

Bn30

3: 0 speed
function
Multifunction
terminal I5
1: second accurate stop function 4:
function selection
external fault input
2: low-speed function

Cn46

Multifunction
terminal
maximum speed

Set range Unit

Factory Modifi
setting cation

0: invalid

Define speed setting value of

multifunction terminal I5

08000

rpm

400

Control requirements
1. When I5 is defined as low-speed function, and input simultaneity with I1 or I2, spindle
enters low speed state.
2. To suppress analog interference and fluctuation, the maximum speed of low-speed
function shall not be set too high. The function is generally used for shift.

0 speed function
The function may be used when user wants motor in 0 speed shaft locking state during
operating. The 0 speed shaft locking function can be set through Bn30.

Function
code

Name

Factory Modifica
setting
tion

Description

Set range

Unit

032767

0.0

100

0: invalid

Bn30

Multifunction
terminal I5
function selection

3: 0 speed
function
1: second accurate stop function
4: external fault input
2: low-speed function

Cn36

0 speed reaches
standard

Set 0 speed reaching standard. 0

speed signal is output when the
output speed is lower than the
setting value.

GS DRIVER

CTB

External fault input function

The function may be used when user wants take external fault signal (emergency stop,
motor thermal protection switch, etc.) as input signal and fed it back to driver to make driver
generates alarm and stops quickly.
Note: priority of the function is the highest in the entire control.

Function
code

Name

Description

Set
range

Unit

Factory
setting

Modifi
cation

Bn30

Multifunction
terminal I5
function selection

0: invalid
3: 0 speed function
1: second accurate stop function 4:
external fault input
2: low-speed function

GS DRIVER

CTB

Trouble shooting
The chapter introduces common faults and remedies of the driver.
List of fault alarm and remedies .7-2
Common fault analysis.7-3
Alarm reset method..7-7

GS DRIVER
List of fault alarm and remedies

CTB

Protection function is activated, and LED digital tube displays fault information, fault output relay is activated and driver stops the output
when fault occurs.
Please see Table 7-1 for faults and remedies of GS driver.
For technical support, please contact the manufacturer.
Table 7-1 Faults and remedies
Fault code

Fault

Possible reason

Remedies

Power supply voltage is higher than the allowable input

voltage range.
The voltage variation of the input power is too large.
Regeneration discharge resistor is not connected.
The external regeneration discharge resistor does not
match.
Overvoltage
Speed of the motor is too high, and cannot absorb
energy in preset time.
Load inertia increases and cannot absorb energy
during deceleration of the motor.
Voltage inspection parameters are set inappropriately.
Driver (internal circuit) failure.

Measure line voltage between R, S and T.

Add power voltage regulator.
Inspect connection of regeneration discharge resistor.
Replace resistance and power to be in accordance with the
specified regeneration discharge resistor.
Reduce the motor speed, and check parameter Cn12 and Cn30.
Increase the capacity of the drive, extend the acceleration and
deceleration time, and add regeneration discharge resistor.
Check parameter Pn00 and Pn01.
Please replace it with a new driver.

The power supply voltage is lower than the allowable

input voltage range.
The voltage variation of the input power is too large.
Under voltage
Power capacity is too low.
Voltage inspection parameters are set inappropriately.
Driver (internal circuit) failure.

Measure the line voltage between R, S and T to check it lower than

330V or not.
Add power voltage regulator.
Increase power capacity.
Check parameter Pn00 and Pn02.
Please replace it with a new driver.

Motor cable (U,V,W) short circuit.

Main circuit
Motor cable (U,V,W) grounded.
over current
Motor winding burned.

Check motor cable to ensure that there is no short-circuit in U,V and

W, and the cable is connected properly
checking insulation resistance of U,V and W and PE line. Replace it

GS DRIVER

CTB
Motor cable poor contact.
Motor does not match with driver.
Motor operating parameters are set incorrectly.
Drive (internal IGBT or other components) failure.

with a new driver if damaged.

Check resistance between motor cable U,V and W. Replace it with
a new driver if the resistance is unbalance.
Check U,V and W terminal of motor for loosing or missing to ensure
reliable electrical connection.
Check nameplate of the driver, use matching motor or as required
or reduce load.
Check driver's relevant motor control parameters.
Test driver power components referring CTB product maintenance
manual, and replace it with new drive.

Motor cable connection error.

Electromagnetic brake is not released.
Motor cable is connected incorrectly in wiring of
multiple motors.
The load torque increases suddenly.
The motor operates with a heavy load for a long time
with torque exceeding the set value.
Improper current gain set.
Unreasonable driver motor parameters set
Encoder feedback signal interference

Check connection between the motor power cable U,V,W and the
driver.

Check the electromagnetic brake, measure brake voltage.

Connect motor cable and encoder cable to the corresponding

driver correctly.

Check the mechanical rotating components, reduce the load.

Increase capacity of driver and motor. Reduce the load.

Re-adjust gain.

Check drive motor control parameters.

Check encoder cable. Make cable shielding treatment to reduce

interference.

Ambient temperature of the driver exceeds the

specified value.
Cooling duct of the driver is blocked and the fan is
damaged.
Radiation fin Driver works for a long time in the state of overload.
overheating
Driver (internal temperature detection circuit) failure

Reduce ambient temperature, and improve the cooling

condition.

Check and clean cooling duct and replace fan.

Check the mechanical rotating components, reduce the load.

Please replace it with a new driver.

Overload

Inversion
module
overheating

GS DRIVER
Fault code

CTB
Fault

Possible reason

Driver works for a long time in the state of overload.

Motor thermal protection connection error or thermal
protection parameter setting error.
Motor overheating
Cooling duct of the driver is blocked or wrong fan
direction or the fan is damaged.
Driver (internal detection circuit) failure
Motor over speed
Driver contactor
failure

Remedies
Increase capacity of driver and motor or reduce the load.
Check thermal protection wiring connection and thermal
protection parameter Pn05.
Clean motor cooling duct, modify fan direction, and replace
fan.
Please replace it with a new driver.

Encoder parameters sett error.

Check encoder parameter Dn10.
Command PULSE sub-frequency multiplication ratio Check Command PULSE sub-frequency multiplication
is set improperly.
parameters Sn82, Sn83.
Contactor damaged

Encoder connection cable is cut off.

Encoder installation failure.
Encoder feedback failed
failure
Encoder failure.
Driver encoder parameter set incorrect
Driver (internal encoder feedback circuit) error

Please replace it with a new driver.

Check encoder connection cables and wiring.

Check encoder installation.
Replace the encoder.
Check the driver encoder control parameters .
Please replace it with a new driver.

Check parameter Dn12 and Dn30.

Please replace it with a new driver.

Braking circuit
failure

Braking switch damaged

External failure

Terminal function is defined as external fault input

function.

Terminal receives external fault signal.

Check terminal defined function.

Check terminal wiring and replace the main board.

Encoder connection cable is cut off.

Check encoder connection cables.

No encoder
feedback
Encoder higher
speed missing

Damage to the data stored in the memory when read

E2PROM parameter
Turn off the power and turn on again. Please replace it
and write data from the EEPROM at the instant of
error
with a new driver if it still fails.
power-on.

GS DRIVER

CTB
Internal
communication
error

Driver internal data communication breaks off.

Timing time reached The set time in timing function has reached.
Self-learning

Indicates the driver is in self-learning state.

Self-learning
completed

Indicates the driver completed self-learning.

Turn off the power and turn on again. Please replace it

with a new driver if it still fails.

Check the set time.

GS DRIVER

CTB

Common fault analysis

The drive and the motor may fail to operate to the design requirements due to parameter
setting or wiring error during system startup. As no alarm code output from the driver,
please make appropriate treatment referring to the section.

No display on drive after power-on

Trouble: the manipulator has no display after power-on of the driver. The trouble may be
caused by several reasons, and shall be checked carefully. please remove all control lines
before inspection.
Reason: drive rectifier bridge failure, inverter bridge failure, switching power supply failure
or starting resistance failure.
Main circuit indication inspection
For situation which indicator is on, rectifier bridge is normal, charging resistor is normal and
switching power supply failure, please contact manufacturer for repair or professional
maintenance;
Please make further inspection when the indicator is off.
Check the driver input power is normal or not.
Measure three-phase AC voltage of R / S / T terminal of the driv

er with multimeter and

check for normality. Normal power supply: 330V <power <440V.

No voltage indicates power failure;
Please make further inspection when it's normal.

Rectifier bridge inspection

Measure the rectifier bridge with multimeter by the method specified in " CTB product
maintenance manual ".
If the rectifier bridge is normal and the charging resistor is burned, please contact
manufacturer for repair or professional maintenance;
If the rectifier bridge is damaged, please replace the rectifier bridge. Manufacturer repair is
recommended.

Spindle cannot run

Trouble: spindle does not rotate when driver power-on and displays f. 0 and CNC system
sends operation order.
Reason: CNC system fails to send frequency command or operation order, control logic
error and improper parameter setting may make the spindle do not rotate. It shall be
inspected carefully.

GS DRIVER

CTB

Inspect the speed setting value on the driver, namely the displayed value of F.
Make the CNC system execute S1000 M3, and observe the display on driver is F. 1000 or
not.
If it is F. 1000, check driver's output frequency U1-1, feedback frequency U1-2;
If it is not F. 1000, please inspect that the CNC system sent frequency command and
operation command correctly or not.
Test driver's output frequency O and feedback frequency b
If U1-1 is same with U1-0, the U1-2 is 0, please inspect motor and wiring, and contact
manufacturer for repair or professional maintenance;
If U1-1 is not same with U1-0, or equals to 0, please inspect acceleration parameter Cn12,
or contact with the manufacturer.
Inspect that has the CNC system sent frequency command and operation command
correctly
Monitor analog input value U2-5 or U2-6, as well as switching value input state U2-2 with
monitoring parameter of U2. As normal, the analog value is about 100% (the maximum
speed of spindle is 8000rpm), and other switching value input signals are 0.
If it's normal, check analog input port selection parameter Bn01 and Bn02. Please contact
the manufacturer if the problem still exists.
If it's not normal, measure abnormal command signal at driver terminals with multimeter.
Measure command signal sent by CNC system
If it's normal, the driver control panel receive signal falsely, please replace control panel or
contact manufacturer for repair.
If it's not normal, check the CNC system interface and driver wiring as well as valid
electrical level of driver signal.
Check motor and wiring
Remove motor connection wire from driver, and measure DC resistance between any twork
of the items with multimeter to judge the motor and wiring is normal or not.
If it's normal, the driver module is burned;
If it's not normal, replace the motor or wiring.

Spindle runs in low speed

Trouble: adjust set speed (frequency), the U1-0 set speed ( frequency ) on the manipulator
is shown normal. However, the spindle speed is very low ( about dozens rpm), and does not
change with the set speed.
Reason: spindle motor encoder feedback abnormal or motor sequence error.

GS DRIVER

CTB

Check the motor and encoder wiring

Normal wiring: U / V / W of motor and driver are connected correspondingly, and the wiring
of encoder is correct.
Abnormal: adjust wiring;
Normal: inspect that the encoder line and physical line number of encoder are in conformity
with D n10.
Inspect encoder signal
Method: driver power-on, respectively measure A + and A-, B + and B-, Z +and the Z- on
control panel of the driver in standby state with DC 20V gear of multimeter.
The normal value is about +3 V or-3V.
Normal: inspect encoder cable;
Abnormal: encoder failure, replace the encoder.
Inspect encoder cable
Method: Remove both ends of the encoder cable respectively from the motor and driver,
measure the core cables respectively with ohm gear of multimeter to check conduction.
Abnormal: encoder cable failure, replace the cable;
Normal: encoder failure, replace the encoder.

Spindle speed setting error

Trouble: great deviation between the set speed (frequency) of U1-0 on driver and set speed
of S command on CNC system.
Reason: the parameter setting on driver or CNC system do not match, or analog interface
failure.
Adjust parameter setting of driver and CNC system
Check the drive parameters:
Bn02, analog type
Cn01, analog 0 point positive offset
Cn02, analog 0 point negative offset
Cn10, maximum output speed
Cn11, analog zero drift setting
Check the CNC system parameter setting:
If the settings are normal, measure voltage of analog port with multimeter.
Check analog port voltage
Normal port voltage = set speed / maximum speed 10 ( V )
Take the maximum speed 8000 rpm of spindle for example, it shall be inspected by the

GS DRIVER

CTB

following table, and error within 0.1% is normal.

CNC system set speed rpm

400

800

1000

2000

4000

8000

analog port

Unipolar

0.50

1.00

1.25

2.50

5.00

10.00

Voltage

Bipolar

0.50

1.00

1.25

2.50

5.00

10.00

Driver displays set speed

400

800

1000

2000

4000

8000

Correct detection value: driver analog port failure, replace driver control panel;
Wrong detection value: CNC system analog output port failure, replace interface boardof
the CNC system.

Spindle accurate stop position is not accurate

Common phenomenon of inaccurate accurate stop:
The spindle accurate stop angle has deviation with tool magazine in initial use or after
replacement of spindle, motor and synchronous belt;
Change of accurate stop position after a certain time operation;
Occasional inaccurate accurate stop position during operation.
Initial use or replacement of spindle
Re-adjust accurate stop angle and adjust parameter: Cn04, accurate stop offset
Cn05, second accurate stop offset
Change of accurate stop position after a certain time operation
Phenomenon: deviation is stable after change of accurate stop position, and does not
recover.
Inspect: the synchronous belt is loose or not; the synchronous belt wheel of spindle motor
is loose or not; the encoder of spindle motor is loose or not.
Treatment: please make corresponding repair if the above phenomenon occurs, or contact
with the manufacturer to replace encoder.
Occasional inaccurate accurate stop position during operation
Please contact with the manufacturer to replace encoder after confirming the following
situation.
The cables of encoder are connected reliably, and the shielding layer are well grounded.
The logic of accurate stop program of the CNC system is correct.
The fault still occasionally occurs after carrying out manual accurate stop in MDI mode
several times.

Over voltage alarm during deceleration

GS DRIVER
Driver displays

CTB
or

alarm.

Reason: deceleration parameter of driver is set inappropriately and driver brake circuit fails
or braking resistor burned.
Check acceleration and deceleration parameters of the driver
Stop the driver, and reduce setting value of Cn12 or Cn30. Reduce 100 each time, and
restart again to observe.
Make further inspection if the alarm still exists.
Inspect braking resistor
When the display is power off, measure resistance at both ends of the braking resistor with
ohm gear of multimeter. If the resistance is infinite, the braking resistor is burned. If it's
same with nominal resistor, the braking resistor is normal.
Confirm driver fault
Make the driver run, and then measure DC bus (between P ( + ) and N) voltage during
deceleration of the driver with DC 1000V gear of multimeter. Measured value greater than
750V indicates fault in brake circuit of the driver, or external brake unit, please contact with
the manufacturer for repair.

Trouble due to encoder failure

Spindle rotates in low speed smaller than 100 rpm, the operating current exceeds the
rated current, and torque reaches 1000, the speed setting dose not work.
During high-speed operation (greater than 3000 rpm), the speed cannot reach the set
speed, and the torque reaches 1000.
During low-speed operation, it has obvious mechanical noise, the speed is non-uniform,
the operation is not stable, and not in control of operating signal.
[Link] [Link] [Link], [Link] alarm appear.
The spindle rotates in high speed and not in control of operation signal.

faults occur frequently

Fault reason:
Instantaneous under voltage may be caused by thunderstorm weather, or time section
with large power supply voltage fluctuation or start of large equipment.
Poor contact in power supply circuit. Please check contact of breaker, contactors, fuses in
power supply circuit carefully for poor contact (shall be judged only by measurement of
multimeter).
Treatment method:
Add regulated power supply for region with grid with unstable voltage, adjust setting value

GS DRIVER

CTB

of Pn02 and Pn04.

Solve line fault.
Replace faulty low voltage electrical appliances

Leakage protection switch is actuated

Phenomenon: when the servo spindle starts, the leakage protection switch trips.
Reason: the leakage protection switch is not the special type for servo (or transducer), the
leakage protection value is set too small.
Remedies:
for common leakage protection switch, the recommended leakage protection value is
200mA, or cancel the leakage protection switch.
for special leakage protection switch for servo (or transducer), the leakage protection
value is 30mA.
add isolation transformer between common leakage protection switch and servo driver.

Alarm reset method

Alarm reset includes the following methods:
reset through ENTER on the manipulator panel.
reset through external terminal RET with reset signal greater than 100ms.
Turn off the driver, and power on again after driver power indicator is off

GS DRIVER

CTB

Maintenance
The chapeter introduces the basic requirements and methods of routine maintenance of the
driver.
Prompt.........................................................8-2
Routine maintenance...................................8-2
Regular maintenance...................................8-3
Wearing parts of the driver..8-3
Driver storage................................................8-4
Driver warranty..............................................8-5

GS DRIVER
Prompt

CTB

Hidden fault of the driver may be caused by effect of temperature, humidity, pH, dust,
vibration and other factors of the service environment, as well as aging, wear of internal
components of the driver and many other reasons. Therefore, routine inspection must be
conducted to the driver and driving system during storage and application, and make
maintenance regularly.
Caution
Dangerous high voltage exists during operation of the driver. Inappropriate operation may
result in serious personal injury. Dangerous high voltage still exists for a period of time after
the power is turned off.
Only trained and authorized qualified professionals can conduct driver maintenance.
Watch, ring and other metal objects of maintenance personnel must be removed before
operation. Clothing and tools that meet insulation requirements must be applied during
operation. Fail to observe the above requirements may lead to electric shock.

Danger
When inspect or maintain the driver, never touch the main circuit terminals or other
components in the driver directly or through metal tools before confirm the following four
items completely; otherwise there is a risk of electric shock.
Shut off the drive power supply reliably, and wait at least 5 minutes;
Open cover plate of the driver after all LED indicators on the operating panel are off;
Charging indicator (CHARGE light) at the right lower of internal of the driver is off;
Measure voltage between main circuit terminal P ( + ), n ( - ) and confirm that the voltage
is lower than 36VDC

Danger
Don't leave screw, wire, tools and other metal items in the driver. Otherwise, the driver
may be damaged.
Never make unauthorized modification to the internal of the driver. Otherwise, the normal
operation of the driver will be affected.
There is electrostatic sensitive IC elements on the control panel in the driver. Do not touch

GS DRIVER

CTB

IC elements on the control panel directly.

Maintenance to main board of the driver shall be conducted only by manufacturer.

Routine maintenance
Routine maintenance shall be carried out during regular operation of the driver to
guarantee excellent operating environment; and record daily operation data, parameter
setting data, parameter changing and so on, establish and improve equipment application
file.
Through routine maintenance and inspection, various abnormal situations may be found
timely and find out causes, and eliminate hidden fault, ensure normal operation of
equipment, and prolong service life of the driver.
List of routing maintenance item
Inspect
object

Inspection main point and judge standard

Inspection content

Cycle

temperature,
humidity
Service
Any
environm dust, moisture and
time
ent
dribbling
gas

vibration
Driver

radiating and
heating
noise
vibration

Motor

heating
noise

Any
time

Any
time

Inspection method

digimite,
hygrometer
observation
observation and
nasil

Operatin
g state
paramete
r

comprehensive
observation and
hearing
digimite

voltmeter
Any
time

Ambient temperature is lower 45,

otherwise, derating operation. Humidity
meets application requirements.
no accumulated dust, water leakage
mark and condensation.
(3) no abnormal color and foreign odor.
Ambient temperature is lower 45,
otherwise, derating operation. Humidity
meets application requirements.

stable operation without vibration.

comprehensive
observation
fan works normally, wind speed and
digimite and
quantity are normal; no abnormal
heating.
comprehensive
observationhearing
(3)no abnormal noise.

hearing
power supply
input voltage
driving output
voltage
driving output
current
internal
temperature

Judge standard

rectifier type
voltmeter
ammeter
digimite

no abnormal vibration and abnormal

sound.
no abnormal heating.
no abnormal noise.

meet requirement of specifications.

meet requirement of specifications.
meet requirement of specifications.
temperature rise lower than 40.

GS DRIVER

CTB

Regular maintenance
To eliminate hidden fault, and guarantee long term table operation of high performance,
user shall carry out a regular inspection to the driver every 3 6 months or shorter interval
according to the service environment.

Regular inspection content

1. The connector is loose or not;
2. Check main circuit terminals for poor contact, and copper row connection for mark of
overheat;
3. Check power cable, control cable for damage, especially cutting mark on skin which in
contact with metal surface;
4. Check insulation binder of power cable nose for falling off;
5. Clean dust on printed circuit board and air passage completely. It is best to use the
cleaner;
6. Before insulation test to the driver, all connections between driver, power supply and
motor, and short all of main circuit input and output terminals with wire reliably, and then
test against ground.
------------------------------------- Insulation precautions --------------------------------Please use qualified 500V Meg-ohmmeter (or corresponding gear of insulation tester). Do
not use defective instrument.
It's strictly prohibited to conduct insulation test against ground with only single main circuit
terminal connected, or there will be a risk of damage to driver.
Never make insulation test to control terminals, otherwise driver will be damaged.
Do remove all of wires which short main circuit terminals after test.
------------------------------------------------------------------------------7. For insulation test to motor, the connections between the motor and driver must be
disconnected completely, and then test the motor separately.

Wearing parts of the driver

Wearing parts of the driver mainly includes cooling fan and electrolytic capacitor for filtering.
Their service life are closely related with operating environment and maintenance status. In
most cases, service life of fan is 30-40 thousand hours; service life of electrolytic capacitor
is 40-50 thousand hours. The normal replacement age limit shall be determined referring to
service life of wearing parts and on the basis of working time of the driver. Component shall
be replaced when abnormalities is found during inspection. When replace wearing part, it's

GS DRIVER

CTB

shall be ensured that the model and electrical parameter of the components are identical or
very close to each other.

Wearing parts of the driver

Routine inspection of common wearing parts
1. Fan
Damage cause: bearing wear, blade aging.
Criteria: check fan blades and other parts for cracks or other abnormalities when the driver
is turned off; check operation of the fan for abnormal vibration, noise and so on when the
driver is started.
2. Electrolytic capacitor
Damage cause: high ambient temperature, large PULSE power, electrolyte aging.
Criteria: frequent over-current, over-voltage in load operation of the driver; liquid leakage
and safety valve protruding; the measured insulation resistance of static capacitance is
abnormal or not.

Driver storage
1. Storage environment
Drive storage environment requirement
Environment
characteristics
Ambient
temperature
Ambient
humidity
Other conditions

Requirem
ent

Remarks

The driver shall be stored in long term in environment with temperature

- 40+70 lower than 30 to avoid condensation and freezing due to temperature
variation
595% rh Plastic film enclosure and desiccant and other measures may be applied
No direct sunlight, dust, corrosive or combustible gas, oil mist, steam, gas, dropping
water, vibration and little salt.

2. For long-term idle, it's recommended to turn the driver on for more than half an hour
every 6 months during storage to prevent failure of electronic components, or conduct
no-load operation to the driver.
Drive warranty
1. For fault or damage of the driver under normal application conditions, the warranty is
valid within 12 months from the date of delivery. A reasonable repair cost shall be paid for

GS DRIVER

CTB

fault or damage after 12 months;

2. A certain of repair cost shall be paid for the following situations even within the 12
months.
(1). Machine damage due to wiring and operation that not in accordance with the user
manual;
(2). Damage caused by fire, floods and abnormal voltage;
(3). Damage caused when use the driver in abnormal function application;

GS DRIVER
Appendix

CTB

Program code

Description

Corresponding CNC system

J000

Standard spindle
function

All CNC systems

J001

Spindle full analog

closed loop control

Hardware
connection

FAnUc 0i(Mate)-Mc

FAnUc 0i(Mate)-Tc

FAnUc 0i(Mate)-MD

3.5

FAnUc 0i(Mate)-TD

SinUMERiK 802D Sl

SinUMERiK 802D

SinUMERiK 802S/c base line

SinUMERiK 801

FAGOR 8055i

10

FAGOR 8035i

11

MiTSUbiSHi E64

12

MiTSUbiSHi E60

13

KnD-100Ti

16

GSK983M

18

GSK980M

21

(Huazhong) 21M

22

(Aerospace) 2100EM

25

(Aerospace) 2100ET

26

(Shenyang Golding) GJ-210M

27

(Shenyang Golding) GJ-210T

28

(Dalian Guagnyang ) GT-8000NC

29

(Dasen)

J002

J003

spindle analog
+PULSE control

Spindle full PULSE

(Renhe)

33

(Huaxing)

40

KnD-1000M

14.15

KnD-1000T

17

GSK-218M

19

GSK-988T

20

(Huazhong) Hnc-210M

23

(Huazhong) Hnc-210T

24

GREA-150iM

30

GREA-150iT

31

GREA-88TA

32

lnc-M600

36

Remarks

GS DRIVER

CTB
control

lnc-T320

37

(SYNTEC)900

38

(SYNTEC)940

39

J004

Communication
control

J100

General feeding
shaft control

J101

Analog feeding shaft

control

J200

Vertical lathe feeding

control program 1

42

J201

Vertical lathe feeding

control program 2

43

J202

Vertical lathe feeding

control program 3

J300

Gantry milling
workbench control
program 1

J301

Gantry milling
workbench control
program 2

J400

Other

41

Note: number in hardware connection indicates page in "CTB servo (spindle) application
manual ".

GS DRIVER
Appendix 2

CTB
CTB spindle application scheme principle

[Link] full analog control

[Link] +PULSE control

[Link] 0 bit switch

[Link]-encoder control

GS DRIVER
Appendix 3

CTB
List of spindle motor code

Motor Model

Code

Motor Model

Code

Motor Model

Code

CTB-40P7ZXA10-

09

CTB -45P0ZC07-

3F

CTB -4013ZE05-

6F

CTB -41P1ZA15-

10

CTB -47P0ZC10-

40

CTB -4018ZE07-

70

CTB -41P5ZA20-

11

CTB -49P5ZC15-

41

CTB -4026ZE10-

71

CTB -42P2ZA30-

12

CTB -4013ZC20-

42

CTB -4037ZE15-

72

CTB -41P1ZA10-

13

CTB -45P5ZC07-

43

CTB -4015ZE05-

73

CTB -41P5ZA15-

14

CTB -47P5ZC10-

44

CTB -4022ZE07-

74

CTB -42P2ZA20-

15

CTB -4011ZC15-

45

CTB -4030ZE10-

75

CTB -43P7ZA30-

16

CTB -4015ZC20-

46

CTB -4045ZE15-

76

CTB -41P5ZA10-

17

CTB -47P5ZC07-

47

CTB -4022ZE05-

77

CTB -42P2ZA15-

18

CTB -4011ZC10-

48

CTB -4030ZE07-

78

CTB -43P7ZA20-

19

CTB -4015ZC15-

49

CTB -4045ZE10-

79

CTB -45P5ZA30-

1A

CTB -4022ZC20-

4A

CTB -4060ZE15-

7A

CTB -42P2ZA10-

1B

CTB -49P0ZC07-

4B

CTB -4026ZE05-

7B

CTB -43P7ZA15-

1C

CTB -4013ZC10-

4C

CTB -4037ZE07-

7C

CTB -45P5ZA20-

1D

CTB -4018ZC15-

4D

CTB -4060ZE12-

7D

CTB -47P5ZA30-

1E

CTB -4026ZC20-

4E

CTB -4075ZE15-

7E

CTB -42P2ZB10-

1F

CTB -45P5ZC07-P

4F

CTB -4026ZF05-

7F

CTB -43P7ZB15-

20

CTB -47P5ZC10-P

50

CTB -4037ZF07-

80

CTB -45P5ZB20-

21

CTB -4011ZC15-P

51

CTB -4055ZF10-

81

CTB -47P5ZB30-

22

CTB -4015ZC20-P

52

CTB -4075ZF15-

82

CTB -43P7ZB10-

23

CTB -47P5ZC07-P

53

CTB -4030ZF05-

83

CTB -45P5ZB15-

24

CTB -4011ZC10-P

54

CTB -4045ZF07-

84

CTB -47P5ZB20-

25

CTB -4015ZC15-P

55

CTB -4065ZF10-

85

CTB -4011ZB30-

26

CTB -4022ZC20-P

56

CTB -4090ZF15-

86

CTB -45P5ZB10-

27

CTB -49P0ZC07-P

57

CTB -4037ZF05-

87

CTB -47P5ZB15-

28

CTB -4013ZC10-P

58

CTB -4055ZF07-

88

CTB -4011ZB20-

29

CTB -4018ZC15-P

59

CTB -4075ZF10-

89

CTB -4015ZB30-

2A

CTB -4026ZC20-P

5A

CTB -4110ZF15-

8A

CTB -47P0ZB10-

2B

CTB -47P5ZC05-P

5B

CTB -4045ZF05-

8B

CTB -49P5ZB15-

2C

CTB -4011ZC07-P

5C

CTB -4065ZF07-

8C

CTB -4013ZB20-

2D

CTB -4015ZC10-P

5D

CTB -4090ZF10-

8D

CTB -4018ZB30-

2E

CTB -4022ZC15-P

5E

CTB -4132ZF15-

8E

CTB -42P2ZB10-P

2F

CTB -46P0ZD05-

5F

CTB -4055ZG05-

8F

CTB -43P7ZB15-P

30

CTB -49p0ZD07-

60

CTB -4080ZG07-

90

CTB -45P5ZB20-P

31

CTB -4013ZD10-

61

CTB -4110ZG10-

91

CTB -47P5ZB30-P

32

CTB -4018ZD15-

62

CTB -4160ZG15-

92

CTB -43P7ZB10-P

33

CTB -47P5ZD05-

63

CTB -4065ZG05-

93

GS DRIVER

CTB

CTB-45P5ZB15-P

34

CTB-4011ZD07-

64

CTB-4100ZG07-

94

CTB-47P5ZB20-P

35

CTB-4015ZD10-

65

CTB-4132ZG10-

95

CTB-4011ZB30-P

36

CTB-4022ZD15-

66

CTB-4200ZG15-

96

CTB-45P5ZB10-P

37

CTB-49P0ZD05-

67

CTB-4080ZG05-

97

CTB-47P5ZB15-P

38

CTB-4013ZD07-

68

CTB-4120ZG07-

98

CTB-4011ZB20-P

39

CTB-4018ZD10-

69

CTB-4160ZG10-

99

CTB-4015ZB30-P

3A

CTB-4026ZD15-

6A

CTB-4250ZG15-

9A

CTB-47P0ZB10-P

3B

CTB-4011ZD05-

6B

CTB-4100ZG05-

9B

CTB-49P5ZB15-P

3C

CTB-4015ZD07-

6C

CTB-4160ZG07-

9C

CTB-4013ZB20-P

3D

CTB-4022ZD10-

6D

CTB-4200ZG10-

9D

CTB-4018ZB30-P

3E

CTB-4030ZD15-

6E

CTB-4315ZG15-

9E