IS 5816 : 1999

( Reaffirmed 2004 )

Indian Standard
SPLITTING TENSILE STRENGTH OF CONCRETE -
METHOD OF TEST
(First Revision )

ICS91.100.30 '

OBIS 1999

BUREAU OF INDIAN STANDARDS

MANAKBHAVAN,9BAHADURSHAHZAFARMARG
NEWDELHI 110002

.Ju(v
1999 Price Group 4
Cement and Concrete Sectional Committee, CED 2

FORE WORD

This Indian Standard (First Revision) was adopted by the Bureau of Indian Standards, after the draft finalized by
the Cement and Concrete Sectional Committee had been approved by the Civil Engineering Division Council.

Tensile strength is one of the basic and important properties of concrete. A knowledge of its value is required for
the design of concrete structural elements subject to transverse shear, torsion, shrinkage and temperature effects.
Its value is also used in the design of prestressed concrete structures, liquid retaining structures, [Link]
runway slabs. Direct tensile strength ofconcrete is difficult to determine; recourse is often taken to the determination
of flexural strength or the splitting tensile strength and computing the direct tensile. The usefulness ofthe splitting
cube test for assessing the tensile strength of concrete in the laboratory is widely accepted and the usefulness of
the above test for control purposes in the field is under investigation. The standard has been prepared with a view
to unifying the testing procedure for this type of test for tensile strength of concrete.

This standard was first published in 1970. In this first revision test on cube specimen has also been incorporated
as it was felt that cube specimens, being used for compression testing, would be convenient to use.

In this revision assistance has been derived from BS I88 1 (Part 117) : 1983 ‘Method for determination of tensile
splitting strength’. Assistance has also been rendered by conducting test and supplying valuable data by the
following:

National Council for Cemenl and Building Material, Ballabgarh and Ciujrat Ambuja Cement, Ahmedabad.

In reporting the result of a test made in accordance with this standard, ifthe final value, observed or calculated, is
to be rounded off, it shall be done in accordance with IS 2 : 1960 ‘Rules for rounding off numerical values
(/[Link])’ .

The composition of the technical committee responsible for the formulation of this standard is given at Annex A.
 IS 5816 : 1999

Indian Standard
SPLITTING TENSILE STRENGTH OF CONCRETE-
METHOD OF TEST
( First Revision )
I SCOPE preparation of materials, proportioning, weighing,
mixing, workability, moulds, compacting and curing
This standard covers the procedure for determining the shall comply in all respects with the requirements given
splitting tensile strength of moulded concrete cubes and in IS 516.
cylinders.
4 APPARATUS
2 NORMATIVE REFERENCES
4.1 Testing Machine
The Indian Standards listed below contain provisions,
which through reference in this standard, constitute Any compression machine of reliable type, of sufficient
provision of this standard. At the time of publication capacity for the tests and capable of applying the load
the editions indicated were valid. All standards are at the rate specified in 7.5 shah be used. It shall comply
subject to revision and parties to agreement based on with the requirements given in IS 516 as far as
this standard are encouraged to investigate the applicable except that the bearing faces of both platens
possibility of applying the most recent editions of the shall provide a minimum loading area of 12 mm x the
standards indicated below: length of the cylinder or cube, as the case may be so
that the load is applied over the entire length of the
IS No. Title specimen. If necessary, a supplementary bearing bar
or plate of machined steel may be used.
516 : 1959 Method of test for strength of concrete
1500: 1983 Method for Brine11hardness test for 4.2 Jigs
metallic materials (second revision)
1658 : 1977 Fibre hardboards (second revision) Either jig shown in Fig. 1 for splitting cylindrical and
cubic specimen or alternatively jig shown in Fig. 2 for
3 TEST SPECIMENS
cubic specimen shall be used.
3.1 Cube
4.2.1 Components of Jigs shown in Fig. 1

Cube specimen shall be of size not less than four times [Link] Two packing strips of tempered hardboard of
the maximum size of the course aggregate and not nominal thickness 4 mm conforming to IS 1658 having
less than 150 mm. following dimensions of the test specimen shall be used
only once:
3.2 Cylinder
Width 15*2mm
The cylindrical specimen shall have diameter not less Nominal thickness 4mm
than four times the maximum size of the coarse Length Greater than the length of the
aggregate and not less than 150 mm. The length of the line of content of the test
specimens shall not be less than the diameter and not specimen
more than twice the diameter. For routine testing and
4.2. I .2 Steel loading strips
comparison of results, unless otherwise specified the
specimens shall be cylinder 150 mm in diameter and A steel loading plate having minimum hardness value,
300 mm long. when tested in accordance with IS 1500 shall be used
. between the platen of the machine and the hardboard
3.3 Making and Curing Test Specimen packing strips. The piece shall not be shorter than the
specimen. For cylindrical specimens it shall be of
The procedure of making and curing tension test rectangular cross section. For cubic specimens, it shall
specimen in respect of sampling of materials, be a section of a cylinder, with a,radius of 75 mm, so

1
IS 5816 : 1999

that the load is applied along a line on the surface of 550 when tested in accordance with IS 1500, shall be
the specimen (see Fig. 1A and 1B). This loading piece auxiliary platens incorporating steel strips with the
can be incorporated within the jig. following dimensions:

4.2.2 Components of Jigs shown in Fig. 2 Width 6* 1 mmfor 150mmsize

Thickness 4*1mm
[Link] Steel loading pieces Length Not less than the length of the line
of content with the test specimen
Steel loading pieces having a minimum hardness of

HARDBOARD
PACKING STRIP DETAIL AT A
LOADING PIECE

FIG. IA APPARATUS FOR SPLITTING CYLINDERS

FIG. 1 B APPARATUS FOR SPLITTING CYLINDER AND CUBE

FIG. 2 ALTERNATE APPARATUS FOR SPLITTING CUBES

 IS 5816 : 1999

4.3 Tolerances in the plane of the pre-marked lines, shall be measured

near the ends and the middle of the specimen and the
The steel loading pieces specified in [Link] and [Link] average taken to the nearest 0.2 mm. The length of the
shall have flatness, squareness parallelism and surface specimen shall be taken to the nearest 0.2 mm by
requirements along the length of the strips within the averaging the two lengths measured in the plane
tolerances given below: containing the pre-marked lines.

a>Flatness - 0.03 mm for each contact face. 7.4 Placing of the Specimen in the Testing Machine
b) Squareness - for each edge of the piece with
respect to the adjacent edge as datum shall be The bearing surfaces of the testing machine and of the
0.06 mm. loading strips shall be wiped clean.
c) Parallelism - one contact face with respect
to the other face as datum shall be 0.06 mm. 7.4.1 Positioning
d) Ra value for the surface texture of the contact
faces - 0.04 m and 3.2 m. The test specimen shall be placed in the centring jig
with packing strip and/or loading pieces carefully
The steel loading pieces shall be replaced when the positioning along the top and bottom of the plane of
dimensions are out of tolerance or they are seriously loading of the specimen. The jig shall then be placed
damaged or pitted along the content face. in the machine so that the specimen is located centrally.
In the case ofcubic specimens, the load shall be applied
5 AGE AT TEST on the moulded faces in such a way that the fracture
plane will cross the trowelled surface.
Tests shall be made at the recognized ages of the test
specimens, the most usual being 7 and 28 days. Tests For cylindrical specimen it shall be ensured that the
at any other age at which the tensile strength is desired upper platen is parallel with the lower platen.
may be made, if so required. The ages shall be
calculated from the time of the addition ofwater to the 7.5 Rate of Loading
dry ingredients. The age at test shall be reported along
with the results. The load shall be applied without shock and increased
continuously at a nominal rate within the range 1.2 N/
6 NUMBER OF SPECIMENS (mm*/min) to 2.4 N/ (mmVmin). Maintain the rate, once
adjusted, until failure. On manually controlled
At least three specimens shall be tested for each age of machines as failure is approached the loading rate will
tests. decrease; at this stage the controls shall be operated to
maintain as far as possible the specified loading rate.
7 PROCEDURE The maximum load applied shall then be recorded. The
appearance of concrete and any unusual features in the
7.1 Specimens when received dry shall be kept in type of failure shall also be noted.
water for 24 h before they are taken for testing. Unless
other conditions are required for specific laboratory The rate of increase of load may be calculated from
investigation specimen shall be tested immediately on the formula:
removal from the water whilst they are still wet. Surface
water and grit shall be wiped off the specimens and (1.2 to 2.4) x 7r/2 x I x d N/min
any projecting fins removed from the surfaces which
are to be in contact with the packing strips. 8 CALCULATION

7.2 Marking 8.1 The measured splitting tensile strengthfc, of the

specimen shall be calculated to the nearest 0.05 N/mm2
Central lines shall be drawn on the two opposite faces using the following formula :
of the cube using any suitable procedure and device
that will ensure that they are in the same axial plane. L=+$

7.3 Measurement where

The mass and dimensions of the specimen shall be P = maximum load in Newtons applied to the . . ..
noted before testing. The sides of the specimen, lying specimen,

3
IS 5816 : 1999

I = length of the specimen as shown in Fig. 3 c) Age of specimen at date of test when known,
(in mm), and
d) Curing history,
d = cross sectional dimension of the specimen
as shown in Fig. 3 (in mm). e) Weight of specimen in Newtons,

9 REPORT 0 Type of fracture and the appearance of

concrete on the fractured face if these are
9.1 The following information shall be included in unusual,
the report on each specimen: Splitting tensile strength to the nearest 0.05
8)
a) Date of test, N/mm’ on the lower side, and

b) Identification mark, shape and size of the h) Estimate of the proportion of coarse aggregate
specimen in mm, fractured during test.

FIG. 3 .PLANEOF LOADING

 IS 5816: 1999

ANNEX A
(Foreword)
COMMITTEE COMPOSITION
Cement and Concrete Sectional Committee, CED 2
Chairman
DR H.C. VKVESVARAYA
Chandrika, 63-64, East Park Road,
Malleswaram, Bangalore 560003

Members Representing

SHRI H. BHAITAOIARYA Orissa Cement Limited, New Delhi

SHRI G. R. BHARTIKAR B.G. Shrike &Co, Pune

DR A. K. CHATXR~EE The Associated Cement Companies Ltd, Mumbai

SHRI S. H. SUBRAMANIAN(Alrernale)

CHIEF ENGINEER (DESIGN) Central Public Works Department, New Delhi

SIJPERINTENDINGENGINEER (S&S) (llbernafe)

CHIEF ENGINEER, NAVAGAM DAM Sardar Sarovar Nirman Nigam Ltd, Gandhinagar
SUPERINTENDIN(;ENGINEER. QCC (Alternate)

CHIEF ENGINEER (RESEARCH-CUM-DIRECTOR) Irrigation and Power Research Institute, Amritsar

RESEARCHOFFICER (CONCRETETECHNOLOGY) (Alternate)

DIRECTOR A. P. Engineering Research Laboratories, Hyderabad

JT DIRECTOR(Alfernate)

DIRWTOR (C’MDD) (N&W) Central Water Commission, New Delhi

DY DIRECTOR (CMDD) (NW&S) (Ahernate)

SHRI K. H. GANGWAL Hyderabad’ Industries Ltd, Hyderabad

SHRI V. PA~ABHI (Alternate)

SHRI V. K. GHANEKAR Structural Engineering Research Centre (CSIR), Ghaziabad

SHRI S. GOPINATH The India Cements Ltd, Chennai

SHRI R. TAMILAKARAN (Alternate)

SHRI S. K. GUHA THAKURTA Gannon Dunkerley & Co Ltd, Mumbai

SHRI S. P. SANKARANARAYANAN(Alternate)

SHRI N. S. BHAL Central Building Research Institute (CSIR), Roorkee

DR IRSHAD MASOOD (Alternate)

DR IRWAD MASSED Cement Corporation of India, New Delhi

SHRI N. C. JAIN (Alfernote)

JOINT DIRECTOR STANOARDS(B&S) (CB-I) Research, Designs & Standards Organization (Ministry of Railways),
Lucknow
JOINT DIRECTOK STANDARDS(B&S)
(CB- 1 I) (Alternate)

SHIR N. G. JOSHI Indian Hume Pipes Co Ltd, Mumbai

SHiR P. D. KELKAR (Alternate)

SHRI D. I(. KANIJNGO National Test House, Calcutta

SHRI B. R. MEENA (ACemate)

SHRI P. KRIsHNA~~~RI~~~ Larsen and Toubro Limited, Mumbai

SHRI S. CHAKRAVARTHY (Alfernate)

(Conrinued on page 6)

5
IS 5816: 1999
(Continued,from page 5)

Members Representing

DR A. G. MADHAVA RAO Structural Engineering Research Centre (CSIR), Chennai

SHRI K. MANI (Alternate)

SHRI G. K. MAJUMDAR Hospital Services Consultancy Corporation (India) Ltd, New Delhi
SHRI J. SARUP (Alternate)

SHRI PRAFULLAKUMAR Ministry of Transport, Department of Surface Transport, Roads Wing,

SHR~ P. P. NA~R (Alternate) New Delhi

MEMBER SECRETARY Central Board of Irrigation and Power, New Delhi

DIRECTOR(CIVIL) (Afremafe)

SHRI S. K. NAITHANI, SO I Engineer-in-Chiefs Branch, Army Headquarters, New Delhi

DR A. S. GOEL, EE (Alternate)

SHRI Y. R. PHLILL Central Road Research Institute (CSIR), New Delhi

SHRI S. S. SEEHRA (Allernole)

SHKI Y. R. PHULL Indian Roads Congress, New Delhi

SHR~ A. K. SHARMA (Aliernate)

,
DR C. RAJKUMAR National Council for Cement and Building Materials, New Delhi
DR K. MOHAN (Alternate)

SHRI G. RAMDAS Directorate General of Supplies and Disposals, New Delhi

SHRI R. C. SHARMA (Alternate)

SHRI S. A. REDDI Gammon India Ltd, Mumbai

SHRI J. S. SANGANERIA Geological Survey of India, Calcutta

SHRI L. N. AGARWAL (Alternate)

SHRI S. B. SURI Central Soil and Materials Research Station, New Delhi
SIIRI N. CHANDRASEKARAN (Alternate)

S~J~ERINTENDINGENGINEER(DESIGN) Public Works Department, Government of Tamil Nadu, Chennai

EXECUTIVE ENGINEER. S.M.R. DIVISION (A/fern&e)

SHRI A. K. CHADHA Hindustan Prefab Ltd, New Delhi

SHRI J.. R. SIL (Alrernate)

DR H. C. VISVESVARAYA The Institution of Engineers (India), Calcutta

SHRI D. C. CHATURVEDI (Alternate)

SHRI VINOD KUMAR, Director General, BIS (Er-oflcio Member)

Director (Civ Engg)

Member-Secretary

SHRI J. K. PRASAD
Additional Director (Civ Engg), BIS

Concrete Subcommittee, CED 2 : 2

Convener

DR A. K. MULLICK National Council for Cement & Building Materials, New Delhi

Members

SHRI C. R. ALIMCHANDANI Stup Consultants Ltd, Mumbai

SHRI S. RANGARAJAN(Alternate)

DR P. C. CHOWDHARY Torsteel Research Foundation in India, Calcutta

DK C. S. VISHWANATH (Alternan)

(Continued on page 7)

6
 IS 5816 : 1999
(( ‘onlimred, from page 6)

Members Representing

SHKI J. P. DESAI Gujarat Ambuja Cement Ltd, Ahmedabad

SHRI 13. K. JAC~ETIA(Alrernate)

DIKECTOR Central Soil Materials Research Station. New Delhi

SI~RI N. CHANDRA~EKARAN(Allernate)

JT DIRECTOR STANDARDS(B&S)/CB-I 1 Research, Designs & Standards Organization, Lucknow

JT DIRECTOR STDS (B&S)/CB-,l (Alternafe)

SUPERINTENDINGENGINEER (DESIGNS) Central Public Works Deptt, New Delhi

EXECUTIVE ENGG. (DESIGNS) (Alternate)

SIIR~ V. K. GHANAKAR Structural Engineering Research Centre, Cihaziabad

SHRI D. S. PRAKASHRAO (Alternate)

SCIRIS. K. GUHA THAKLJRTA Gannon Dunkerlay & Co Ltd. Mumbai

SHRI S. P. SANKARANARAYANAN(Aiternafe)

SHRI J. S. HINGORANI Associated Consulting Services, Mumbai

SHRI A. P. REMEDIOS (Alfernate) ’

SHRI LALIT KIJMAR JAIN In personal capacity (Consulting Structural Engineer, 36, Old Sneh
Nagar, Wardha Road, Nagpur 440015)

SHRI M. P. JAISINGH Central Building Research Institute, CSIR, Roorkee

SHRI B. KAMESWARA RAO (Alternafe)

C’HIEF ENGINEER & JOINT SECRETARY Public Works Department, Mumbai

SWERINTENDING ENGINEER (A/fern&e)

PROF. S. KRISHNAMOORTHY Indian Institute ofTechnology, New Delhi

SI~RI K. K. NAYAR (Alternate)

DR S. C. MAI II National Council for Cement & Building Materials, New Delhi

MANAGING DIRECTOR Hindustan Prefeb Ltd. New Delhi

SHRI M. KUNDU (Ahernate)

SIIRI M. K. MWERJEE Ministry of Transport (Road Wing). New Delhi

SHRI N. K. SINHA (Al/et&e)

StttuB. V. B. PAI The Associated Cement Co Ltd. Mumbai

SHRI M. G. DANDAVATE (Alternate)

SHRI A. B. PHADKE The Hindustan Construction Co Ltd. Mumbai

SHRI 0. M. SAVUR (Al/ernafe)

SHRI Y. R. PIWLL Central Road Research Institute, New Delhi

SW S. S. SEEHRA (Alternate I)
SHRI SAT~NDER KUMAR (Alternate II)

SHRI A. S. PRASAD RAO Structural Engineering Research Centre (CSIR), Chennai

SHRI K. MANI (Alternate)

SHRI K. L. PRVTHI National Building and Construction Corporation Ltd, New Delhi
SHRI J. R. GABRIEL (Al&ware)

SHRI B. D. RAHALKER Nuclear Power Corporation, Mumbai

Sari II. S. P. VERMA (Alternate)

SHRI HANUMENTHA RAO A. P. Engineering Research Laboratories, Hyderabad

SiiRI G. RAMAKRISHNEN(Alternate)

SHRI S. A. REDDI Gammon India Ltd, Mumbai

DR N. V. NAYAK (Alternate)

(Continued on page 8)

7
IS 5816 : 1999

(Con/inued,from page 7)

Members Representing

SHRIS. C. SAWHNE~ Engineers India Ltd, New Delhi

SHRI R. P. MEHROTRA(Al#ernale)

SHRIJ. II. SHARMA Army Headquarters, Engineekin-ChiePs Branch, New Delhi

SHRISVRINDERMOHAN(Alternate)

PROFM. S. SHEITY Indian Concrete Institute, Chennai

SHRI B. 1‘. UNWALLA In personal capacity (1519, Rustam Baug, Victoria Road, Mumbai-27)

DIRECTOR(CBMDD) Central Water Commission, New Delhi

DY DIRECTOR(C&MDD) (Alternate)
Bureau sf Indian Standards

BIS is a statutory institution established under the Bureau of Itrdiart Standards Act, 1986 to promote
harmonious development of the activities of standardization, marking and quality certification of goods and
attending to connected matters in the country.

Copyright

BIS has the copyright of all its publications. No part of these publications may be reproduced in any form
without the prior permission in writing of BIS. This does not preclude the free use, in the course of
implementing the standard, of necessary details, such as symbols and sizes, type or grade designations.
Enquiries relating to copyright be addressed to the Director (Publication), BIS.

Review of Indian Standards

Amendments are issued to standards as the need arises on the basis of comments. Standards are also reviewed
periodically; a standard along with amendments is reaffirmed when such review indicates that no changes are
needed; if the review indicates that changes are needed, it is taken up for revision. Users of Indian Standards
should ascertain that they are in possession of the latest amendments or edition by referring to the latest issue
of ‘BIS Handbook’ and ‘Standards Monthly Additions’.
This Indian Standard has been developed from Dot: No. CED 2 (4850).

Amendments Issued Since Publication

Amend No. Date of Issue Text Affected

BUREAU OF INDIAN STANDARDS

Headquarters:
Manak Bhavan, 9 Bahadur Shah Zafar Marg, New Delhi 110002 Telegrams: Manaksanstha
Telephones: 323 0131,323 33 75,323 94 02 (Common to all offices)

Regional Offices: Telephone

Central : Manak Bhavan, 9 Bahadur Shah Zafar Marg 323 76 17,323 38 41

NEW DELHI 110002
Eastern : l/14 C.I.T. Scheme VII M, V.I.P. Road, Maniktola 337 84 99,337 85 61
CALCUTTA 700054 { 337 86 26,337 9120

Northern : SC0 335336, Sector 34-A, CHANDIGARH 160022 60 38 43

{ 60 20 25

Southern : C.I.T. Campus, IV Cross Road, C!IENNAI 600113 235 02 16,235 04 42

{ 235 15 19,235 23 15

Western : Manakalaya,E9 MIDC, Marol, Andheri (East) 832 92 95,832 78 58

MUMBAI 400093 { 832 78 91,832 78 92

Branches : AHMADABAD. BANGALGRE. BHOPAL. BHUBANESHWAR.

COIMBATORE. FARIDABAD. GHAZIABAD. GUWAHATI.
HYDERABAD. JAIPUR. KANPUR. LUCKNOW. NAGPUR.
PATNA. PUNE. THIRUVANANTHAPURAM.
fited at SimcoprintingPress,Delhii India