AVS Manual
Home / Caterpillar / Troubleshooting / i01525971
IT12F, IT14F, IT18F, IT24F and IT28F Integrated
Toolcarriers and 910F, 918F, 924F and 928F
Wheel Loaders Power Train Electronic Control
System Caterpillar
Automation Devices
Vibratory Feeding Systems
Vibratory Equipment Tailored To Customer
Specifications.
[Link]
OPEN
MID 081 - CID 0645 - FMI 06
Usage:
IT28F
1JL
Conditions Which Generate This Code:
Illustration 1 g00618544
Locations of the Solenoid
(1) Solenoid 1
(2) Solenoid 2
(3) Solenoid 3
(4) Solenoid 4
(5) Solenoid 5
(6) Solenoid 6
Illustration 2 g00619119
Schematic of Solenoid 5
Use table 1 in order to determine the solenoids that are energized. Table 1 identifies the solenoids that are energized for
each position on the shift lever.
Gear Solenoid that is Energized
Neutral No solenoids are energized.
Forward 1 3 and 4
Forward 2 3 and 5
Forward 3 3 and 6
Forward 4 1 and 5
Forward 5 1 and 6
Reverse 1 2 and 4
Reverse 2 2 and 5
Reverse 3 2 and 6
Table 1
Note: The approximate coil resistance of the solenoid is 34 ohms at 25 °C (77.0 °F).
This diagnostic code is recorded when the ECM reads the voltage of the solenoid circuit as being below normal range (open
circuit).
Note: This procedure can cause new diagnostic codes to be recorded. Ignore these created diagnostic codes. Complete the
following procedure. Then clear the created diagnostic codes.
This diagnostic code is associated with transmission solenoid 5.
FMI 06 is recorded when the transmission electronic control module senses a short. The short is to ground.
Test Step 1. CHECK FOR A SHORT TO GROUND.
A. Turn the key start switch to the OFF position.
B. Disconnect the machine harness from the control module.
C. Measure the continuity from contact 2 to contact 35.
Expected Result:
There is NOT continuity.
Results:
YES - There is NOT continuity. The solenoid harness does not have a short to ground. Connect the machine's
harness. Verify that the diagnostic code is active. If the diagnostic code is present, the transmission electronic
control module has failed.
Repair: It is unlikely that the ECM has failed. Exit this procedure and perform this procedure again. Also, recheck if the
diagnostic code is active. If the cause of the diagnostic code is not found, replace the transmission ECM. See Testing
and Adjusting, "Electronic Control Module (ECM) - Replace".
Stop.
NO - There is continuity. The solenoid harness has a short to ground or the solenoid has a short to ground.
Repair: Repair the harness or replace the harness or the solenoid.
Stop.
Caterpillar Information System:
816F Landfill Compactor, 815F Soil Compactor and 814F Wheel Dozer Cooling System Coolant Level - Check
120H, 12H, 135H, 140H, 143H, 160H and 163H Motor Graders Hydraulic and Steering System Centershift Lock
2001/05/14 Special Instruction, REHS0142-05 for Backhoe Loader Pin Bores is Now Updated {6104, 6119,
6501, 6502, 6503, 6506, 7054}
IT12F, IT14F, IT18F, IT24F and IT28F Integrated Toolcarriers and 910F, 918F, 924F and 928F Wheel Loaders
Power Train Electronic Control System MID 081 - CID 0645 - FMI 05
TK1051 Track Feller Buncher Machine Systems Pilot Valve (Travel and Steering)
IT12F, IT14F, IT18F, IT24F and IT28F Integrated Toolcarriers and 910F, 918F, 924F and 928F Wheel Loaders
Power Train Electronic Control System MID 081 - CID 0645 - FMI 03
2001/05/14 A New Support Is Used on the Boom and Stick of the Knuckle Boom Loaders {5057, 5057, 6501,
6502}
AS2301 Screed Burner Group (Main) - Remove
IT12F, IT14F, IT18F, IT24F and IT28F Integrated Toolcarriers and 910F, 918F, 924F and 928F Wheel Loaders
Power Train Electronic Control System MID 081 - CID 0644 - FMI 06
Ai C diti i dH ti R134 f All C t ill M hi El t i H tC t l T t
Air Conditioning and Heating R134a for All Caterpillar Machines Electronic Heat Control - Test
Product Identification Numbers (PIN) Location Guide Ripper
TK1051 Track Feller Buncher Swing Gear - Lubricate
TK1051 Track Feller Buncher Machine Systems Pressure Taps (Implement) - Tool Tilt, Boom and Stick
IT12F, IT14F, IT18F, IT24F and IT28F Integrated Toolcarriers and 910F, 918F, 924F and 928F Wheel Loaders
Power Train Electronic Control System MID 081 - CID 0646 - FMI 03
TK1051 Track Feller Buncher Machine Systems Pilot Control Valve
740 and 740 EJECTOR Articulated Trucks Power Train Machine Preparation for Troubleshooting
740 and 740 EJECTOR Articulated Trucks Power Train Visual Inspection
2001/04/23 Parts Manuals for Skid Steer Loaders Are Now Provided on CD-ROMs {7000}
2001/05/07 Correction to the Parts Manual, SEBP3204 for the Installation Arrangement {1316, 1326, 1405,
1453}
3176C and 3406E Engines for Caterpillar Built Machines E040 Low Engine Oil Pressure Shutdown
312C, 315C, 318C, 319C, 320C, 322C, 325C and 330C Excavators Air Conditioning and Heating Refrigerant
Compressor
816F Landfill Compactor, 815F Soil Compactor and 814F Wheel Dozer Cooling System Coolant Extender (ELC)
- Add
216, 226, 232 and 242 <BR>Skid Steer Loaders Machine Systems Lift Cylinder - Remove
816F Landfill Compactor, 815F Soil Compactor and 814F Wheel Dozer Cooling System Water Temperature
Regulator - Replace
SIS Information
General Service Information
Schematic
Specifications
Systems Operation
Testing and Adjusting
Troubleshooting
Disassembly and Assembly
Service Magazine
Truck Engine News
Engine News
Lift Truck Technical Bulletin
Operation and Maintenance
Manual
Contacts
The names Caterpillar, John Deere, JD, JCB, Hyundai
or any other original equipment manufacturers are registered
My AVS
trademarks of the respective
original equipment manufacturers.
All names, descriptions, numbers and symbols are used for
reference purposes only.
[Link] is in no way associated with any of the manufacturers we have listed.
All manufacturer's names and
descriptions are for reference only.
