Page 1 of 88
303-01 Engine - 2.3L EcoBoost (201kW/273PS) 2019 Ranger
Disassembly Procedure revision date: 01/4/2019
Engine
Base Part Number: 6L084
Special Tool(s) / General Equipment
205-153 (T80T-4000-W)
Handle
303-1685
Alignment Tool, Camshaft
303-1687
Installer, VCT Solenoid Seal
303-1689
Holding Tool, Crank Damper
303-409 (T92C-6700-CH)
Remover, Crankshaft Seal
TKIT-1992-FH/FMH/FLMH
TKIT-1993-LMH/MH
303-507
Timing Peg, Crankshaft TDC
TKIT-2001N-FLM
TKIT-2001N-ROW
307-005 (T59L-100-B)
Slide Hammer
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN/... 1/9/2019
Page 2 of 88
310-206
Remover, Fuel Injector
TKIT-2009A-FLM
Mounting Stand
Plastic Scraper
Hose Clamp Remover/Installer
Materials
Name Specification
Motorcraft® Silicone Gasket Remover -
ZC-30-A
Motorcraft® Metal Surface Prep Wipes -
ZC-31-B
Motorcraft® Metal Brake Parts Cleaner -
PM-4-A, PM-4-B
NOTICE: Do not loosen or remove the crankshaft pulley bolt without first installing the special tools as
instructed in this procedure. The crankshaft pulley and the crankshaft timing sprocket are not keyed to
the crankshaft. The crankshaft, the crankshaft sprocket and the pulley are fitted together by friction. For
that reason, the crankshaft sprocket is also unfastened if the pulley bolt is loosened. Before any repair
requiring loosening or removal of the crankshaft pulley bolt, the crankshaft and camshafts must be
locked in place by the special service tools, otherwise severe engine damage can occur.
NOTICE: During engine repair procedures, cleanliness is extremely important. All parts must be
thoroughly cleaned and any foreign material, including any material created while cleaning gasket
surfaces, that enters the oil passages, coolant passages or the oil pan, can cause engine failure.
1.
l Remove the bolts and the flexplate.
l Discard the bolts.
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN/... 1/9/2019
Page 3 of 88
2. Using a floor crane, install the engine on a mounting stand.
Use the General Equipment: Mounting Stand
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN/... 1/9/2019
Page 4 of 88
3. Remove the engine lift equipment.
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN/... 1/9/2019
Page 5 of 88
4.
l Remove the ground bolt.
l Disconnect the wiring harness electrical connectors.
l Detach the wiring harness retainers.
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN/... 1/9/2019
Page 6 of 88
5.
l Disconnect the wiring harness electrical connectors.
l Detach the wiring harness retainers.
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN/... 1/9/2019
Page 7 of 88
6.
l Disconnect the wiring harness electrical connectors.
l Detach the wiring harness retainers.
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN/... 1/9/2019
Page 8 of 88
7.
l Disconnect the wiring harness electrical connectors.
l Detach the wiring harness retainers.
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN/... 1/9/2019
Page 9 of 88
8.
l Disconnect the wiring harness electrical connectors.
l Detach the wiring harness retainers.
9.
l Disconnect the wiring harness electrical connectors.
l Detach the wiring harness retainers.
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN/... 1/9/2019
Page 10 of 88
10. Detach the wiring harness retainers and remove the engine wiring harness.
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN/... 1/9/2019
Page 11 of 88
11.
l Release the clamps and remove the coolant hose.
Use the General Equipment: Hose Clamp Remover/Installer
l Disconnect the coolant hose and the retainers and remove.
12. Remove the bolt and position the coolant tube aside.
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN/... 1/9/2019
Page 12 of 88
13. Remove the bolt and position the turbocharger coolant tube aside.
14. Remove and discard the turbocharger coolant tube O-ring seal.
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN/... 1/9/2019
Page 13 of 88
15.
1. Remove the coolant tube support bracket bolt.
2. Remove the bolt and the coolant tube support bracket.
16. Remove the bolts and the coolant tube.
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN/... 1/9/2019
Page 14 of 88
17. Discard the coolant tube O-ring seal.
18.
l Loosen the clamps and remove the EGR transducer hoses.
Use the General Equipment: Hose Clamp Remover/Installer
l Remove the bolt and the EGR transducer assembly.
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN/... 1/9/2019
Page 15 of 88
19.
1. Remove the EGR valve bracket nut.
2. Remove the bolt and the EGR valve bracket.
20. Remove the bolt, nuts and the EGR valve.
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN/... 1/9/2019
Page 16 of 88
21. Remove and discard EGR valve O-ring seal.
22. Remove and discard the EGR valve gasket.
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN/... 1/9/2019
Page 17 of 88
23. Remove bolt, stud bolt and the EGR cooler bracket.
24. Remove the bolts and the EGR cooler.
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN/... 1/9/2019
Page 18 of 88
25. Remove and discard the EGR cooler gaskets.
26. Remove the nuts, bolts and the EGR inlet tube assembly.
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN/... 1/9/2019
Page 19 of 88
27. Remove and discard the EGR inlet tube assembly gasket.
28. Remove the bolts and the coolant tube.
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN/... 1/9/2019
Page 20 of 88
29. Inspect the coolant tube O-ring seal and replace if damaged.
30. Remove the bolts and the coolant pump pulley.
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN/... 1/9/2019
Page 21 of 88
31. Remove the bolts and the accessory drive belt pulley.
32. Remove the bolts and the accessory drive belt tensioner.
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN/... 1/9/2019
Page 22 of 88
33. Release the clamp and remove the lower radiator hose.
Use the General Equipment: Hose Clamp Remover/Installer
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN/... 1/9/2019
Page 23 of 88
34.
l Remove the upper generator bolt and the bracket.
l Remove the generator nut and stud.
l Remove the lower bolt and the generator.
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN/... 1/9/2019
Page 24 of 88
35. Release the clamps, retainer and remove the coolant hoses.
Use the General Equipment: Hose Clamp Remover/Installer
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN/... 1/9/2019
Page 25 of 88
36.
l Detach the fuel rail harness electrical connector from the intake manifold.
l Detach and disconnect the KS electrical connectors.
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN/... 1/9/2019
Page 26 of 88
37.
l Disconnect the crankcase vent oil separator tube quick release coupling from the intake manifold.
Refer to: Quick Release Coupling (310-00 Fuel System - General Information - 2.3L EcoBoost
(201kW/273PS), General Procedures).
l Remove the bolts and the intake manifold.
38.
l Remove the bolt and the oil cooler.
l Discard the oil cooler.
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN/... 1/9/2019
Page 27 of 88
39. Remove the nut, bolts and the oil filter adapter assembly.
40. Remove the oil filter adapter assembly stud.
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN/... 1/9/2019
Page 28 of 88
41. Remove the bolts and the RH engine mount bracket.
42. Remove the bolts and the A/C compressor bracket.
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN/... 1/9/2019
Page 29 of 88
43. Release the clamps and remove the coolant hose.
Use the General Equipment: Hose Clamp Remover/Installer
44. Disconnect and remove the crankcase vent oil separator tube.
Refer to: Quick Release Coupling (310-00 Fuel System - General Information - 2.3L EcoBoost
(201kW/273PS), General Procedures).
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN/... 1/9/2019
Page 30 of 88
45. NOTE: Note the position of the KS before removing.
Remove the bolts and the KS.
46. Remove the bolts and the crankcase vent separator.
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN/... 1/9/2019
Page 31 of 88
47. NOTE: To release the fuel pressure in the high pressure fuel tube, wrap the fuel injection pump flare nut
with a shop towel to absorb any residual fuel pressure during the loosening of the fuel injection pump flare
nut.
l Remove the high-pressure fuel tube bolts.
l Loosen the flare nuts, remove and discard the high-pressure fuel tube.
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN/... 1/9/2019
Page 32 of 88
48.
l Remove the bolts and discard.
l Remove the high-pressure fuel pump and mounting plate.
49. Remove and discard the high-pressure fuel pump O-ring seal.
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN/... 1/9/2019
Page 33 of 88
50. Remove and discard the fuel pump mounting plate O-ring seal.
51. Remove the high-pressure fuel pump tappet.
52. Remove the bolts and the coolant pump adapter assembly.
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN/... 1/9/2019
Page 34 of 88
53. Remove and discard the coolant pump adapter assembly gasket.
54. Remove the bolt coolant hose bracket.
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN/... 1/9/2019
Page 35 of 88
55. Remove the bolts and discard the turbocharger-to-cylinder block oil return pipe.
56. Remove the nuts, bolt and the heat shield.
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN/... 1/9/2019
Page 36 of 88
57. Remove the bolts and discard the cylinder block-to-turbocharger oil supply pipe.
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN/... 1/9/2019
Page 37 of 88
58. Remove the bolt and the coolant outlet tube.
59. Remove and discard coolant outlet tube O-ring seal.
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN/... 1/9/2019
Page 38 of 88
60. Remove the nuts and the turbocharger.
61. Remove and discard coolant outlet tube seal and O-ring seal.
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN/... 1/9/2019
Page 39 of 88
62.
l Remove and discard the gasket.
l Inspect and replace the studs if damaged.
63. Remove the stud bolts, bolts and the coolant outlet.
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN/... 1/9/2019
Page 40 of 88
64. NOTE: Use compressed air to remove any foreign material from the ignition coil-on-plugs and surrounding
area before removing the ignition coil-on-plugs.
NOTE: When removing the ignition coil-on-plugs, a slight twisting motion will break the seal and ease
removal.
l Remove the stud bolts and the ignition coil-on-plugs.
l Remove the oil level indicator.
65. Loosen the fasteners and remove the valve cover.
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN/... 1/9/2019
Page 41 of 88
66. Discard the valve cover gaskets.
67.
l NOTE: The VCT solenoid seals should only be replaced if they are damaged upon inspection.
Inspect the VCT seals for damage.
l If damaged, using the special tools, remove and discard the VCT oil control solenoid seals.
Use Special Service Tool: 303-1687 Installer, VCT Solenoid Seal. , 205-153 (T80T-4000-W)
Handle.
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN/... 1/9/2019
Page 42 of 88
68. NOTE: Do not use metal scrapers, wire brushes, power abrasive discs or other abrasive means to clean
the sealing surfaces. These tools cause scratches and gouges which make leak paths.
Clean the valve cover.
69. NOTICE: Do not use metal scrapers, wire brushes, power abrasive discs or other abrasive means
to clean the sealing surfaces. These tools cause scratches and gouges which make leak paths.
Make sure that the mating faces are clean and free of foreign material.
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN/... 1/9/2019
Page 43 of 88
70.
l Disconnect the fuel rail wiring harness electrical connectors.
l Detach the fuel rail wiring harness retainers and remove harness.
71. Remove the fuel rail insulator.
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN/... 1/9/2019
Page 44 of 88
72. NOTICE: Pull out the fuel rails in the direction of the fuel injector axis or damage may occur to the
fuel injectors.
NOTE: Use compressed air and remove any dirt or foreign material from the cylinder head, block and
general surrounding area of the fuel rail and injectors.
NOTE: When removing the fuel rails, the fuel injectors may remain in the fuel rails but normally remain in
the cylinder head and require the use of a Fuel Injector Remover tool to extract.
Remove the bolts and the fuel rail.
73. Remove any of the fuel injectors that remained in the fuel rail.
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN/... 1/9/2019
Page 45 of 88
74. Remove any of the fuel injectors that remained in the cylinder head.
Use Special Service Tool: 307-005 (T59L-100-B) Slide Hammer. , 310-206 Remover, Fuel Injector.
75. Remove and discard the fuel injector clip.
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN/... 1/9/2019
Page 46 of 88
76. NOTICE: Do not attempt to cut the lower Teflon® seal without first pulling it away from the fuel
injector or damage to the injector may occur.
NOTE: Be very careful when removing the lower Teflon® seals, not to scratch, nick or gouge the fuel
injectors.
1. Pull the lower Teflon® seal away from the injector.
2. Carefully cut and discard the lower fuel injector Teflon® seals.
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN/... 1/9/2019
Page 47 of 88
77. Remove and discard the fuel injector seal and O-ring seal.
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN/... 1/9/2019
Page 48 of 88
78.
l Remove the CHT sensor and the heat shield.
l Discard the CHT sensor.
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN/... 1/9/2019
Page 49 of 88
79. Remove the bolts and the CKP sensor.
80. Turn the crankshaft clockwise until the No.1 piston is 45 degrees BTDC using the guide holes on the
engine front cover and the crankshaft pulley.
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN/... 1/9/2019
Page 50 of 88
81. Remove the engine plug bolt.
82. Install Special Service Tool: 303-507 Timing Peg, Crankshaft TDC.
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN/... 1/9/2019
Page 51 of 88
83. NOTE: The special tool will contact the crankshaft and prevent it from turning past TDC. However, the
crankshaft can still be rotated in the counterclockwise direction. The crankshaft must remain at the TDC
position during the crankshaft pulley removal and installation.
NOTE: The engine front cover is removed from graphic for clarity.
Rotate the crankshaft clockwise until it contacts the special tool.
Use Special Service Tool: 303-507 Timing Peg, Crankshaft TDC.
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN/... 1/9/2019
Page 52 of 88
84. Remove the bolts and the high-pressure fuel pump drive unit.
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN/... 1/9/2019
Page 53 of 88
85. NOTICE: The Camshaft Alignment Tool is for camshaft alignment only. Using this tool to prevent
engine rotation can result in engine damage.
NOTE: The camshaft timing slots are offset. If the Camshaft Alignment Tool cannot be installed, remove
the TDC Timing Peg and rotate the crankshaft three-fourths of a revolution clockwise and repeat the
previous 2 steps of this procedure.
Install Special Service Tool: 303-1685 Alignment Tool, Camshaft.
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN/... 1/9/2019
Page 54 of 88
86. NOTICE: The crankshaft must remain in the TDC position during removal of the pulley bolt or
damage to the engine can occur. Therefore, the crankshaft pulley must be held in place with the
special tool and the bolt should be removed using an air impact wrench (1/2-in drive minimum).
l Using the special tools, remove the bolt and the crankshaft pulley.
Use Special Service Tool: 303-1689 Holding Tool, Crank Damper.
l Discard the bolt.
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN/... 1/9/2019
Page 55 of 88
87. Install the original crankshaft pulley bolt and washer.
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN/... 1/9/2019
Page 56 of 88
88. NOTICE: Use care not to damage the engine front cover or the crankshaft when removing the seal.
Using the crankshaft seal remover, remove the crankshaft front seal and discard.
Use Special Service Tool: 303-409 (T92C-6700-CH) Remover, Crankshaft Seal.
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN/... 1/9/2019
Page 57 of 88
89. Remove the original crankshaft pulley bolt and washer.
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN/... 1/9/2019
Page 58 of 88
90. Remove the bolts and the engine front cover.
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN/... 1/9/2019
Page 59 of 88
91. NOTICE: Only use a 3M™ Roloc® Bristle Disk (2-in white, part number 07528) in a suitable tool
turning at the recommended speed of 15,000 rpm, to clean the engine front cover. Do not use
metal scrapers, wire brushes or any other power abrasive disk to clean. These tools cause
scratches and gouges that make leak paths.
l Make sure that the mating faces of the engine front cover are clean and free of foreign material.
Refer to: RTV Sealing Surface Cleaning and Preparation (303-00 Engine System - General
Information, General Procedures).
Material: Motorcraft® Silicone Gasket Remover / ZC-30-A
Material: Motorcraft® Metal Brake Parts Cleaner / PM-4-A, PM-4-B
Material: Motorcraft® Metal Surface Prep Wipes / ZC-31-B
l Thoroughly wash the engine front cover to remove any foreign material, including any abrasive
particles created during the cleaning process.
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN/... 1/9/2019
Page 60 of 88
92. NOTICE: Place clean, lint-free shop towels over exposed engine cavities. Carefully remove the
towels so foreign material is not dropped into the engine. Any foreign material (including any
material created while cleaning gasket surfaces) that enters the oil passages or the oil pan, may
cause engine failure.
NOTICE: Do not use metal scrapers, wire brushes, power abrasive discs or 3M™ Roloc® Bristle
Disk (2-in white part number 07528) to clean the sealing surfaces. These tools cause scratches and
gouges that make leak paths. They also cause contamination that will cause premature engine
failure. Remove all traces of the gasket.
Make sure that the mating faces of the engine block and oil pan are clean and free of foreign material.
Refer to: RTV Sealing Surface Cleaning and Preparation (303-00 Engine System - General Information,
General Procedures).
Use the General Equipment: Plastic Scraper
Material: Motorcraft® Silicone Gasket Remover / ZC-30-A
Material: Motorcraft® Metal Brake Parts Cleaner / PM-4-A, PM-4-B
Material: Motorcraft® Metal Surface Prep Wipes / ZC-31-B
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN/... 1/9/2019
Page 61 of 88
93. NOTICE: Use an open-ended wrench on the flats of the camshaft to prevent the component from
turning.
Loosen the exhaust VCT bolt.
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN/... 1/9/2019
Page 62 of 88
94. NOTICE: Use an open-ended wrench on the flats of the camshaft to prevent the component from
turning.
Loosen the intake VCT bolt.
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN/... 1/9/2019
Page 63 of 88
95. Remove the bolts and the timing chain tensioner.
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN/... 1/9/2019
Page 64 of 88
96.
l Remove the timing chain tensioner arm.
l Remove the bolts and the timing chain guide.
l Remove the timing chain.
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN/... 1/9/2019
Page 65 of 88
97.
l Remove the bolts and the VCT units.
l Discard the bolts.
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN/... 1/9/2019
Page 66 of 88
98. Remove Special Service Tool: 303-1685 Alignment Tool, Camshaft.
99. Remove the bolts and the VCT oil control solenoids.
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN/... 1/9/2019
Page 67 of 88
100. Remove bolts and front camshaft bearing cap.
101. NOTICE: Failure to follow the camshaft loosening procedure can result in damage to the
camshafts.
NOTE: Note the location and orientation of each camshaft bearing cap and the position of the camshaft
lobes on the No. 1 cylinder for installation reference.
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN/... 1/9/2019
Page 68 of 88
l Loosen the camshaft bearing caps in sequence 2 turns at a time until all tension is released from
the camshaft bearing caps and remove the camshaft bearing caps and camshafts.
l Inspect the camshaft bores for any scratches that can be felt by hand.
102. NOTE: If the camshafts and valve tappets are to be reused, mark the location of the valve tappets to make
sure they are assembled in their original positions.
Remove the valve tappets.
103. NOTE: There are two numbers on the valve tappet, one is date code and the other is valve tappet
thickness.
NOTE: The date code “R0605” represents the year made (R), the month (06) and the day (05).
NOTE: A tappet with the number N650 has the thickness of 3.650 mm.
Inspect the valve tappets.
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN/... 1/9/2019
Page 69 of 88
104. Remove the bolts, stud bolt and the cylinder head cover assembly.
105. Remove and discard the cylinder head cover gasket.
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN/... 1/9/2019
Page 70 of 88
106.
l Remove the bolts and the cylinder head.
l Discard the bolts.
107. Remove and discard the cylinder head gasket.
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN/... 1/9/2019
Page 71 of 88
108. Remove the cylinder block bushings.
109. NOTICE: Do not use metal scrapers, wire brushes, power abrasive discs or other abrasive means
to clean the sealing surfaces. These tools cause scratches and gouges that make leak paths. Use a
plastic scraping tool to remove all traces of the head gasket.
Clean the cylinder head sealing surfaces.
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN/... 1/9/2019
Page 72 of 88
110. NOTICE: Do not use metal scrapers, wire brushes, power abrasive discs or other abrasive means
to clean the sealing surfaces. These tools cause scratches and gouges that make leak paths. Use a
plastic scraping tool to remove all traces of the head gasket.
NOTE: Clean the cylinder head bolt holes in the cylinder block. Make sure all coolant, oil or other foreign
material is removed.
Clean the cylinder block sealing surfaces.
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN/... 1/9/2019
Page 73 of 88
111.
l Check the cylinder block distortion.
Refer to: Cylinder Block Distortion (303-00 Engine System - General Information, General
Procedures).
l Check the cylinder head distortion.
Refer to: Cylinder Head Distortion (303-00 Engine System - General Information, General
Procedures).
112.
l Remove the bolts and the oil pan.
l Discard the bolts.
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN/... 1/9/2019
Page 74 of 88
113. Remove the bolts and the oil pickup and screen.
114. Discard the oil pickup and screen O-ring seal.
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN/... 1/9/2019
Page 75 of 88
115. NOTICE: Do not use wire brushes, power abrasive discs or 3M™ Roloc® Bristle Disk (2-in white,
part number 07528) to clean the sealing surfaces of the engine block. These tools cause scratches
and gouges that make leak paths. They also cause contamination that causes premature engine
failure. Remove all traces of the gasket.
Make sure that the mating faces of the engine block are clean and free of foreign material.
Refer to: RTV Sealing Surface Cleaning and Preparation (303-00 Engine System - General Information,
General Procedures).
Use the General Equipment: Plastic Scraper
Material: Motorcraft® Silicone Gasket Remover / ZC-30-A
Material: Motorcraft® Metal Brake Parts Cleaner / PM-4-A, PM-4-B
Material: Motorcraft® Metal Surface Prep Wipes / ZC-31-B
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN/... 1/9/2019
Page 76 of 88
116. NOTICE: Only use a 3M™ Roloc® Bristle Disk (2-in white, part number 07528) in a suitable tool
turning at the recommended speed of 15,000 rpm, to clean the oil pan. Do not use metal scrapers,
wire brushes or any other power abrasive disk to clean. These tools cause scratches and gouges
that make leak paths.
l Make sure that the mating faces of the oil pan are clean and free of foreign material.
Refer to: RTV Sealing Surface Cleaning and Preparation (303-00 Engine System - General
Information, General Procedures).
Material: Motorcraft® Silicone Gasket Remover / ZC-30-A
Material: Motorcraft® Metal Brake Parts Cleaner / PM-4-A, PM-4-B
Material: Motorcraft® Metal Surface Prep Wipes / ZC-31-B
l Thoroughly wash the oil pan to remove any foreign material, including any abrasive particles
created during the cleaning process.
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN/... 1/9/2019
Page 77 of 88
117.
l Remove the bolts and the crankshaft rear seal.
l Discard the crankshaft rear seal.
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN/... 1/9/2019
Page 78 of 88
118. Remove the crankshaft sprocket.
119. NOTE: Make sure the Crankshaft TDC Timing Peg is still installed and the engine is still at TDC.
Rotate the crankshaft until it contacts the special tool.
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN/... 1/9/2019
Page 79 of 88
120. NOTE: Mark the balance shaft assembly front shafts on the top for reference that the balance shaft
assembly is at TDC.
Index-mark the balance shaft assembly.
121. Remove the bolts and the oil outlet tube.
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN/... 1/9/2019
Page 80 of 88
122. Inspect the oil outlet tube O-ring seals and replace if damaged.
123.
1. Remove the oil inlet tube-to-bracket bolt.
2. Remove the bolt and the oil inlet tube bracket.
3. Remove the bolts and the oil inlet tube.
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN/... 1/9/2019
Page 81 of 88
124. Inspect the oil inlet tube O-ring seals and replace if damaged.
125. NOTE: Due to the precision interior construction of the balance shaft assembly, it should not be
disassembled.
Remove the bolts and the balance shaft assembly.
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN/... 1/9/2019
Page 82 of 88
126. Remove Special Service Tool: 303-507 Timing Peg, Crankshaft TDC.
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN/... 1/9/2019
Page 83 of 88
127.
1. Inspect ridge.
2. NOTE: Remove the carbon buildup, do not scratch the cylinder wall. Remove all debris from the
cylinder.
Clean with abrasive pad.
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN/... 1/9/2019
Page 84 of 88
128. NOTE: Clearly mark the connecting rods, connecting rod caps and connecting rod bearings in numerical
order for correct orientation for reassembly.
Remove the bolts and the connecting rod caps.
129. NOTICE: Do not scratch the cylinder walls or crankshaft journals with the connecting rod.
Remove the pistons.
130. NOTE: Mark the position of the parts, so they can be installed in their original positions.
Remove the connecting rod bearings.
Refer to: Engine (303-01 Engine - 2.3L EcoBoost (201kW/273PS), Disassembly).
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN/... 1/9/2019
Page 85 of 88
131. Remove the bolts and the main bearing beam.
132. NOTE: If the main bearings are being reused, mark them in order for correct orientation and reassembly.
Remove the main bearing beam bearings.
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN/... 1/9/2019
Page 86 of 88
133. Remove the crankshaft.
134. NOTE: If the main bearings are being reused, mark them in order for correct orientation and reassembly.
NOTE: The center bulkhead has the thrust bearing.
Remove the crankshaft main bearings.
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN/... 1/9/2019
Page 87 of 88
135. Remove the bolts and the engine piston oil cooler valves.
Copyright © 2019 Ford Motor Company
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN/... 1/9/2019
Page 88 of 88
http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN/... 1/9/2019
