Scribd
Upload
230 views4 pages

Dareger Polytron 2 Error Codes

Uploaded by

zabihuq
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF or read online on Scribd
230 views4 pages

Dareger Polytron 2 Error Codes

Uploaded by

zabihuq
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF or read online on Scribd
Drager Polytron 2 IR_ Online Info ‘Online Info’ is displayed by keeping ESC-key depressed, while being in measurement mode: es a legal sys. (0x80, EPROM Checksum TO) or8) [oxo Error 1 (0x40, RAM 8) [0x04 (0x20: Debug, IRG 9) [ox02: x10: [ox0t: Error Delay activated {0x80;_Invalid MFR1 Database Version 8) [Ox08: Wrong Gas Database Error 2 (Ox40:_Invalid MFR2 Database Version 8) [x04 ‘0x20:Invalid MFR3 Database Version 8) [0x02 (x10: Inv. EEPROM Ver. 6) of 7)+3) or 11) [0x01 Sys. 0x60: 0x08: Error 3 0x40: 0x04: 0x20: Sys. ‘Ox80:_MFRi Database 39) [Ox08: Error 4 MFR2 Database 8}+9) [Ox04: HOT Stack 1 3 (0x20: MFR3 Database '8)+9) | 0x02: HC11 Stack 2 9) Joxt0 EEPROM Database: 7)+3) [0x01 3s. 0x80. ‘0x08: Wrong main electronics a Error 5 (0x40: (0x04: Warning Parameters 9) (0x20: Heater Failure 8) [ 0x02: Invalid Vokage 1 (0x10: Analog Database Checksum 2) 10x01: Invalid Curent er aper8) Sys. (0x80; Analog span not calibrated 3) [ono Warning (0x40: Analog zer0 not calibrated 3) [0x04 0x20: 0x02: (0x10: x01 Polytron IR_ Online info Page 1/2 PAIR Error List. doc gs-€eg+tr, 01.12.1999 ‘0x08; Meas Lamp (see Meas Err 4) 3 ‘0x04: Ref Lamp (See Meas Err 4) 5 (0x02; Meas Detector (see Meas Er 4) 5) No valid span calibration E14) (0x01: Ref Detector (see Meas €rr4) 5) ‘0x40: No valid zero calibration 13) 0x04: Debug, (0x20: (0x02: Debug 9) (0x10: Wrong Pre-amplifier Version By 0x01; Debug Di ‘Meas. x80: (0x08: Error 3 foxso: 0x04: 0x20: (0x02: not used 0x10: [oxor: Meas. (0x80: Debug Synchronization Dj 0x08: Low Sig Meas Freq? 3 Signal Cut Ref 3) |> 1 Signal Cut Meas. 3) [0x02:_Low Sig Ref Freq 2 3) Low Sig Meas Freq 1 5) [ox01: _] Meas. ADC 9) [oxo8: Error § [Ox40: ADC 2, 9) [oxo4: 0x20: 0x02: (x10: 0x01: Meas. Warning 1 72) 2) Polytron 21R Online info Check supply voltage Interrupt supply voltage > 1 sec (Reset) Calibrate analog interface Clean external Optical Components On Site: Replace Transmitter DWHL: Check internal Optical Components Perform standard initialization Perform fundamental initialization Replace Transmitter Inform [Link] at Drager-ST, Libeck ‘Thomas. Treptow@[Link] +49-451-882-1966 40) OnSite: Replace Transmitter DWHL: Replace EPROM 11) On Site: Replace Transmitter DWHL: Install EPROM containing latest software 12) Wait for sensor to warm up 13) Calibrate sensor (zero) 44) Calibrate Sensor (span) Hex a decimah — 9s-00g-tr, 01.12.1999 Page 2/2 & PAIR Error [Link]

You might also like