MIT ACADEMY OF ENGINEERING
COURSE CODE: ET483T SEPTEMBER 2022
FINAL YEAR BTECH SEMESTER-VII 2022-23 EXAMINATION
DEPARTMENT OF ELECTRICAL ENGINEERING
MID SEMESTER EXAMINATION
COURSE NAME : ELECTRIC VEHICLES
TIME : 2 HOURS MAX MARKS : 50 MARKS
TOTAL NO OF QUESTIONS: 3 TOTAL NO OF PRINTED PAGES:02
INSTRUCTIONS TO CANDIDATES:
1. Assume suitable data wherever necessary
2. Non programmable scientific calculators are allowed
3. Black figures to the right indicate full marks
1 a) A straight roadway has a profile in the xFyF-plane [4M] CO1 L1
given by for 0=xF=2 miles (xF and
yF are given in feet). Find i) ß(xF) ii) Find the
tangential road length between 0 and 2 miles.
( i)Formulae - 01M ,Solution -1M iI)Formulae - 01M ,Solution -1M )
b) Explain social and environmental benefit of Electric [6M] CO1 L2
vehicle
(Social benefits - 3M for each point, Environmental benefit-03M for each)
2 a) For a 2-wheeler,e-rickshaw and sedan with [10M] CO1 L3
specification given below,compute total traction
force,power and torque required at 30kmph and 80
kmph.Consider the pick up time to attain 30 kmph and
80 kmph to be 20seconds.what would be the power
and torque required if the 4-wheeler sedan goes to
160kmph.Assume slope to be zero.
(Force ,power and torque for each - 8M ,Power and torque for sedan for
160kmph-2M)
[1]
b) Model the acceleration of the electric scooter which [10M] CO1 L3
has a mass of 130 kg, with a typical passenger of
mass 75 kg,drag coeffecient as 0.75.The frontal area
of vehicle and rider is 0.5m2.The tyres and wheel
bearings give a coefficient of rolling resistance, μrr=
0.007.The motor is connected to the rear wheel using
a 2:1 ratio belt system, and the wheel
diameter is 42 cm.The maximum torque Tmax is
34Nm.The critical motor speed, ωc , after which the
torque falls is 103rad/sec.and gear effeciency as 0.98.
(Acceleration when torque is constant = 5M,Acceleration under Maximum
torque=5M)
3 a) Explain the characteristics of DC series and shunt [06M] CO2 L2
motor
(DC series characteristics with diagram-3M,DC shunt characteristics with
diagram-3M)
b) A 440V shunt motor has armature resistance of 0.8Ὠ [04M] CO2 L2
and field resistance of 200Ὠ.Determine the back emf
when giving an output of 7.46KW at 85 percent
effeciency
(Motor input power-1M,input current -1M,Shunt and armature current -01M
each,and back emf -1M)
(or)
Explain the concept of IDC in Electric vehicle [04M] CO1 L2
d) Explain theconstruction,principle and working of BLDC [10M] CO2 L3
motor with diagram
(Construction-2M,Principle -1M,Working -3M,Diagram-4M,)
[2]
F.Y.B.Tech Examination Semester - I In Semester Examination - 1
S.Y.B.Tech Examination Semester - II In Semester Examination - 2
T.Y.B.Tech Examination Semester - III In Course Examination
F.Y.M.Tech Examination Semester - IV Mid Semester Examination
S.Y.M.Tech Examination Semester - V End Semester Examination
Semester - VI End Course Examination
Semester - VII Re-Examination
Semester - VIII In Term Assessment
Trimester - I End Term Assessment
Trimester - II
Trimester - III
Trimester - IV
Trimester - V
Trimester - VI
Time: 1 Hour Max Marks: 20
Time: 1 Hour 30 MinuteMax Marks: 30
Time: 2 Hours Max Marks: 40
Time: 2 Hours 30 MinutMax Marks: 50
Time: 3 Hours Max Marks: 60
Max Marks: 70
Max Marks: 80
Max Marks: 100
Department of Civil Engineering Cycle - 1
Department of Chemical Engineering Cycle - 2
Department of ComputerEngineering
Department of Electronics Engineering
Department of Electronics and Telecommunication Engineering
Department of Information Technology Engineering
Department of Mechanical Engineering
