EK-Quantum
Vector FE RTX 3090 D-RGB + Backplate
GPU WATER BLOCK
USER GUIDE
Before you start using this product, please follow these basic guidelines:
Carefully read the manual before beginning with the
installation process.
Remove your graphics card from the computer for the safest
mounting process, to prevent any possible damage to your
GPU or its circuit board (PCB).
EK Fittings require only a small amount of force to screw
them firmly in place since the liquid seal is ensured with the
rubber O-ring gaskets.
The use of quality market-proven corrosion-inhibiting
coolants is always strongly recommended for any liquid
cooling system.
Do not use pure distilled water as a cooling liquid! For best
results, EK recommends the use of EK-CryoFuel Coolants.
Make sure to bleed air out of your water block thoroughly in
order to reach optimal performance.
TABLE OF CONTENTS
BOX CONTENTS 4
WATER BLOCK DIMENSIONS 5
TEHNICAL SPECIFICATIONS AND WATER BLOCK MAIN PARTS 6
PREPARING THE GRAPHICS CARD 7
REMOVING THE STOCK COOLER 7
CLEANING THE PCB 7
CUTTING AND PLACING THERMAL PADS 8
APPLYING THERMAL COMPOUND 9
INSTALLING THE WATER BLOCK 9
REMOVING THE STOCK BACKPLATE COVER 9
REMOVING THE STOCK BACKPLATE 10
REMOVING THE PRE-INSTALLED I/0 BRACKET 10
PLACING THE BLOCK ON THE GRAPHICS CARD 11
ATTACHING THE BLOCK TO THE GRAPHICS CARD 11
ATTACHING THE I/O BRACKET 12
INSTALLING THE BACKPLATE 13
BACKPLATE DIMENSIONS 13
BACKPLATE COVER DIMENSIONS 13
REQUIRED TOOLS 14
CUTTING AND PLACING THERMAL PADS 14
ATTACHING THE BACKPLATE 15
REPLACING THE TERMINAL (Optional Step) 16
CHECKING FOR CONTACT 18
INSERTING THE GRAPHICS CARD INTO THE CHASSIS 18
INSTALLATION OF FITTINGS AND TUBING 19
CONNECTING THE D-RGB LED STRIP 19
TESTING THE LOOP 20
SUPPORT AND SERVICE 21
SOCIAL MEDIA 21
-3-
BOX CONTENTS Universal Mounting Mechanism – You may not need every
screw from this package.
7 mm
4 mm
M2.5x4 AX1 Screw (9 pcs) M2.5x7 AX1 Screw (4 pcs)
EK-Quantum Vector FE RTX 3090 D-RGB + Backplate M3x5 Screw (3 pcs) PVC Washer M2.5 (7 pcs)
Thermal Grease (1 pc) EK-Plug G1/4 (2 pcs) Allen Key 2 mm (1 pc) EK-Loop Multi Allen Key (1 pc)
120
mm
16 mm
Thermal Pad F 1.0 mm (10 pcs) Additional Terminal Allen Key 2.5 mm (1 pc)
-4-
WATER BLOCK DIMENSIONS
Direct Terminal 28.60 mm
213.50 mm
14.30 mm
121.50 mm
74.75 mm
46.70 mm
Throughout Terminal 213.50 mm
200.80 mm 28.60 mm
121.50 mm
74.75 mm
46.75 mm
-5-
TEHNICAL SPECIFICATIONS AND WATER BLOCK MAIN PARTS
Technical Specification:
- Dimensions (LxHxW): 213.5 x 121.5 x 28.6 mm
- D-RGB (Addressable RGB) Cable - Length: 500 mm
M3 x 12 DIN7991 SCREW - D-RGB LED Count: 20
EK BADGE - D-RGB Connector: Standard 3-Pin (+5V, Data, Blocked, Ground)
M2.5 x 7 AX1 SCREW
BACKPLATE COVER
BACKPLATE
COLDPLATE M3 x 12 DIN7991 SCREW
STANDOFF
TERMINAL O-RING
COLDPLATE
FC TERMINAL
JET PLATE
PLEXI INSERT
M4 x 24.5 DIN7984
MAIN O-RING 144 x 2 mm SCREW
TOP PLATE
M3x5 SCREW
TOP COVER
SINGLE SLOT BRACKET
-6-
PREPARING THE GRAPHICS CARD
STEP 1
REMOVING THE STOCK COOLER
Place your graphics card on the flat surface and carefully remove the
stock cooler. Do not forget to unplug all the LED and fan connectors.
Pay attention to the following steps in order to install the EK-Quantum
Vector FE RTX 3090 water block onto the graphics card.
STEP 2
CLEANING THE PCB
Carefully detach the original stock cooler after removing all screws
that are securing it to the board. Wipe off the remains of the original
thermal compound using a nonabrasive cloth or Q-tip, as shown
in the sample image, until the components and circuit board are
completely clean. EK recommends the use of denatured alcohol for
removing TIM leftovers.
STEP 2
-7-
CUTTING AND PLACING THERMAL PADS
STEP 1
Your GPU water block comes with thermal pads that have to be cut
into smaller pieces to cover all the VRM components, such as COILs,
Thermal Pad F – 1.0 mm (120 x 16 mm) MOSFETs, and drivers.
16 mm
You must remove the protective foil from both sides of the
1 mm
120 mm thermal pad before installation.
Replacement thermal pads:
STEP 1 10x Thermal Pad F 1.0 mm – (120 x 16 mm) EAN: 3830046996732
STEP 2
Thermal Pad F 1.0mm Once cut to size, thermal pads should be placed on the PCB, as
illustrated below. EK made sure to provide you with more than an
adequate quantity of thermal pads to complete this Step.
STEP 2
-8-
APPLYING THERMAL COMPOUND
STEP 1
Apply the enclosed EK-TIM Ectotherm thermal grease (thermal
compound) on the GPU heat spreader – IHS – as shown in the
image. The layer of the thermal compound must be thin and even
over the entire surface of the IHS.
The excessive or uneven application of thermal grease
may lead to poor performance!
For this Step, you will need:
Thermal Grease
STEP 1
INSTALLING THE WATER BLOCK
STEP 1
M3 x 12 REMOVING THE STOCK BACKPLATE COVER
DIN 7991 Carefully unscrew three (3) preinstalled backplate cover screws (M3 x 12
DIN 7991) as shown in the picture using the enclosed Allen Key (2 mm),
and take off the backplate cover. Save the screws and cover for later use.
For this Step, you will need:
BACKPLATE
COVER Allen Key 2.0 mm
STEP 1
-9-
STEP 2
REMOVING THE STOCK BACKPLATE
M2.5 x 7 AX1 SCREWS Carefully unscrew four (4) preinstalled backplate screws (M2.5 X 7
AX1) and remove the backplate, as shown in the picture. Save the
BACKPLATE screws and backplate for later use.
For this Step, you will need:
Phillips Head Screwdriver
STEP 2
STEP 3
REMOVING THE PRE-INSTALLED I/0 BRACKET
Unscrew the three (3) M3X5 screws from the front using Phillips head-
screwdriver and remove the I/O Bracket (as shown in the picture). Save
the screws and I/O Bracket for the later use!
For this Step, you will need:
Phillips Head Screwdriver
M3 x 5 SCREW
STEP 3
- 10 -
STEP 4
PLACING THE BLOCK ON THE GRAPHICS CARD
This procedure is the same for all full-cover water blocks.
Carefully position the water block with preinstalled standoffs on
the graphics card. During this process, make sure you have aligned
mounting holes of the PCB with holes of the water block (the same
applies to other tops).
Pay attention not to use too much force when pressing the
block down to the PCB since chip dies are prone to cracking.
STEP 4
STEP 5
M2.5 x 4 AX1 SCREW ATTACHING THE BLOCK TO THE GRAPHICS CARD
Use four (4) M2.5 X 4 AX1 screws and M2.5 PVC washers, as
M2.5 PVC shown in the image. Tighten the screws around the GPU core
WASHER evenly using the Phillips head screwdriver. Always use a plastic
washer under each screw!
For this Step, you will need:
M2.5 x 4 AX1 M 2.5 PVC Washer Phillips Head
Screw (4 pcs)
4 mm
(4 pcs) Screwdriver
STEP 5
- 11 -
STEP 6
ATTACHING THE I/O BRACKET
M2.5 x 4 AX1 SCREW Take the stored screws and I/O Bracket after attaching the water
block. Attach them on to the water block as shown in the picture.
Do not use excessive force.
For this Step, you will need:
M3 x 5 Screws Phillips Head
I/O Bracket
(3 pcs) Screwdriver
I/O BRACKET
M3 x 5 SCREW
STEP 6
- 12 -
INSTALLING THE BACKPLATE
BACKPLATE DIMENSIONS
7.85 mm
121.5 mm
206.6 mm
90.2 mm 9.20 mm
BACKPLATE COVER DIMENSIONS
121.5 mm
- 13 -
REQUIRED TOOLS
Phillips Head Screwdriver Scissors
CUTTING AND PLACING THERMAL PADS
Your backplate comes with thermal pads that have to be cut into smaller
Thermal Pad F 1.0 mm pieces to cover all the VRM components. EK made sure to provide you with
more than an adequate quantity of thermal pads to complete this Step.
CAUTION: You must remove the protective foil from both
sides of the thermal pad before installation.
Once cut to size, thermal pads should be placed on the backplate,
as shown in the image.
- 14 -
ATTACHING THE BACKPLATE
STEP 1
Apply 3 small pea sized dots of enclosed EK-TIM Ectotherm thermal
grease on the water block as shown in the image.
STEP 1
STEP 2
Place the backplate on the PCB and make sure all holes are aligned.
M2.5 x 7 AX1 SCREW Position an M2.5 x 7 AX1 screw in each of the four (4) mounting
BACKPLATE holes (as shown in the image) and tighten them evenly with a
Phillips Head Screwdriver.
For this Step, you will need:
M2.5 x 7 AX1
Screw (4 pcs)
7 mm
STEP 2
- 15 -
STEP 3
M3 x 12 After securing the backplate, place the backplate cover on the PCB
DIN7991 and make sure all holes are aligned. Position an M3 X 12 DIN7991
screw in each of the three (3) mounting holes (as shown in the
image) and tighten them evenly with a Allen Key 2mm. Do not use
excessive force!
For this Step, you will need:
Allen Key 2.0 mm M3 x 12 DIN7991 Screw (3 pcs)
STEP 3
REPLACING THE TERMINAL (Optional Step)
With the EK-Quantum Vector FE RTX 3090 water block, you also
get an additional terminal. Follow these steps to install it.
STEP 1
Unscrew three (3) M4 x 24.5 DIN7984 terminal screws with the
enclosed 2.5mm Allen Key. Remove the stock terminal. Save the
TERMINAL O-RING screws and terminal O-Rings for later.
FC TERMINAL For this Step, you will need:
Allen Key 2.5 mm
M4 x 24.5 DIN7984 SCREW
STEP 1
- 16 -
STEP 2
Before you attach the new terminal, make sure that terminal gaskets
are placed inside holes on the coldplate (as shown in the picture).
For this Step, you will need:
Terminal Gasket (2 pcs)
TERMINAL
GASKETS
STEP 2
STEP 3
Carefully place the terminal on the coldplate and secure it with
previously saved M4 X 24.5 DIN7984 screws. Do not use excessive
force when tightening the screws.
For this Step, you will need:
M4 X 24.5 DIN7984
Allen Key 2.5 mm Terminal
Screw (3 pcs)
M4 x 24.5 DIN7984
SCREW
STEP 3
- 17 -
CHECKING FOR CONTACT
If necessary, temporarily remove the water block to check for uniform
surface contact between the block and components. Pay special
attention to the VRM section of the graphics card. Check whether
the water block makes contact with the intended integrated circuit.
Then repeat Steps from the previous section to re-attach the block.
In case you fail to obtain good contact, please check
again or contact our support service at
https://www.ekwb.com/customer-support/.
INSERTING THE GRAPHICS CARD INTO THE CHASSIS
Carefully lift your graphics card with the installed water block and
insert it into your PC’s motherboard PCIexpress expansion slot.
Please bear in mind that your graphics card is very likely heavier than
before it was equipped with the water block.
You need to be very careful when handling the
graphics card. Avoid all unnecessary manipulation
of the water block assembly that might damage your
card or water block.
- 18 -
INSTALLATION OF FITTINGS AND TUBING
STEP 1
Screw-in two (2) G1/4 threaded male fittings. Attach the liquid
cooling tubes and connect the water block(s) to the cooling loop.
Do not forget to plug the remaining two openings with
enclosed EK-Plug G1/4 or its equivalent.
You can use any opening as an inlet/outlet port.
EK-FITTING EK recommends using EK fittings with all EK water blocks.
EK- PLUG G1/4 CAUTION: When using connectors other than EK fittings,
TUBING
pay special attention to the length of the fittings’ male G1/4”
STEP 1 thread - 5mm is the maximum G1/4” thread length allowed!
CONNECTING THE D-RGB LED STRIP
STEP 1
Plug the 4-pin D-RGB connector from the GPU water block to the
D-RGB Header on your motherboard or controller. The LED strip will
work only if the pin layout on the header is as follows: +5V, Data,
Empty, Ground.
D-RGB HEADER
Incorrect installation or installation to a wrong header can
damage to the LED strip or the header itself!
RGB HEADER
STEP 1
- 19 -
TESTING THE LOOP
To make sure the installation of EK components was successful,
we recommend you perform a 24-hour leak test.
When your loop is complete and filled with coolant, connect the
pump to a PSU outside of your system. Do not connect power to
any of the other components. Turn on the PSU and let the pump
run continuously.
Inspect all parts of the loop, and in case the coolant leaks, fix
the issue and repeat the testing process. To prevent possible
damage, please ensure that all hardware is dry before the system
is powered on.
- 20 -
SUPPORT AND SERVICE
In case you need assistance, please contact:
https://www.ekwb.com/customer-support/
EKWB d.o.o.
Pod lipami 18
1218 Komenda
Slovenia - EU
SOCIAL MEDIA
EKWaterBlocks
@EKWaterBlocks
ekwaterblocks
EKWBofficial
ekwaterblocks
