Fingerprint & Card Access Control Panel User Guide

Note: The fingerprint & card Access Control panel can connect our company fingerprint
reader or normal wiegand RFID reader.
(1) If connect fingerprint reader: Dial switch A switch 1~8 to ON ,and Dial switch B switch 1~8 to OFF

12V Power suupply

A B Wiegand Reader
(2) If connect normal wiegand RFID reader: Dial switch A switch 1~8 to OFF ,and Dial switch B switch 1~8 to ON

Exit input

12V

A B
485A
12V Power suupply
485B
Wiegand Reader
GND

Exit input Fingerprint reader

12V

-RESET
485A
485B
GND
A
Fingerprint reader
READER D READER C READER B READER A EXIT B EXIT A FIRE 12V DC
-RESET

A ACCESS CONTROL PANEL

READER B READER A EXIT A FIRE 12V DC

RS485 MSG B MSG A LOCK B LOCK A ALARM

B
ACCESS CONTROL PANEL USB
TCP/IP + -

RS485 MSG A LOCK A ALARM

B Lock
Normal Close, Open door with no power
USB (If using electric adaptor with Cathode
TCP/IP + - electric lock(open door with power),
connect to Normal Open and not Normal
Close)
Lock
Normal Close, Open door with no power
(If using electric adaptor with Cathode
electric lock(open door with power), Alarm
Sensor
connect to Normal Open and not Normal
Close)

Sensor Alarm

Single-Door Two-Way Wiring Diagram Two-Door Two-Way Wiring Diagram

 12V Power supply
Wiegand Reader

电源
Exit input
12V

485A

12V
485B

GND

GND

12V+
Fingerprint reader

-RESET
LED BUZZ

DATA 1
DATA 0

GND

12V +

LED BUZZ

DATA 1
DATA 0

GND

12V +

LED BUZZ

DATA 1
DATA 0

GND

12V +

LED BUZZ

DATA 1
DATA 0

GND

12V +

GND
EXIT D

GND

EXIT C

GND

EXIT B

GND
EXIT A

GND

FIRE

GND

12V +
A READER D READER C READER B READER A EXIT D EXIT C EXIT B EXIT A FIRE 12V DC

ACCESS
ACCESS CONTROLPANEL
CONTROL PANEL

RS485 MSG D MSG C MSG B MSG A LOCK D LOCK C LOCK B LOCK A ALARM
B
MSG D

MSG C

MSG B

MSG A

RJ45接口
GND

GND

GND

GND

COM

COM

COM

COM

COM
B+
B-

NO

NC
NO

NC

NO

NC

NO

NC
NO

USB NC
TCP/IP + -

Lock
Normal Close, Open door with no power
(If using electric adaptor with Cathode
electric lock(open door with power),
connect to Normal Open and not Normal
Close)

2: Click the button < Read set> to get the configuration of the controller board.
Sensor 3: Input the device number, IP address, server IP address and port number. Then click the button <Write set>
Alarm
Ⅲ：Door not opened by pressing fingerprint or swipping card
1: Check whether the enrolled fingerprint or card have been uploaded to the controller through the Access control system? Check
whether the FINGER light turning on when pressing a valid fingerprint or swiping a valid card. On the contrary, will the ERR light
turning on when we press an invalid fingerprint or swipe an invalid card.
2：Check whether the person who press fingerprint or swipe card has rights of opening door. Besides, is this rights being uploaded
to the controller.
Four-Door Single -Way Wiring Diagram 3: When pressing fingerprint or swiping card, listen to the pulse sound of the relay. Besides, we could check whether the yellow light
near the relay turning on. If the yellow light is on while there is no sound of pulse in the relay, please check whether the voltage is
too low.
User Guide IV: TCP/IP fail to connect
Ⅰ：Fingerprint Collection 1：Check whether the network cable is broken or the RJ45 jacket is not good. If the metal plate of RJ45 jacket could not contact the
1: Connect the USB fingerprintreader intoa computerwithaccess controlsoftwareinstalled.Run the access wire well, the connection will be lost.
control software to collect fingerprint. 2：Check whether the IP address and the device number are input correctly.
V: Restore to factory default. (It will not affect the enrolled fingerprint and card information in the controller nor the rights
Ⅱ：Setup of the device number , the IP address or the server IP address and the port number of the of opening door)
controller 1: When the controller is power on, press the button <RESET>. Then, the argument in the controller will be restored to the factory
default value(The factory default setting is device number of 1, IP address of 192.168.1.224 and port number of 5005. (It will not
1: Run the programnetconfig.exe.It is in companywith the package of the controller . Then, use USB cable affect the enrollment fingerprint and card information in the controller nor the rights of opening door).
or TCP/IP or RS485 to connectthe controller. (The defaultsettingof the controlleris device numberof 1, IP
address of 192.168.1.224 and port number of 5005).