Scribd
Upload
98 views1 page

S420LC-V - 18.9.2007

This document provides calibration data for an injection pump, including injection quantities at different rack positions and pump speeds, boost pressure dependent full-load stop settings, governor spring specifications, and other injection pump part details.

Uploaded by

Milan
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
98 views1 page

S420LC-V - 18.9.2007

This document provides calibration data for an injection pump, including injection quantities at different rack positions and pump speeds, boost pressure dependent full-load stop settings, governor spring specifications, and other injection pump part details.

Uploaded by

Milan
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd

MAKER NO 106675-461A

INJ.PUMP CALIBRATION DATA


DHI NO 65.11101-7361A
DATE 2003. .
E/G MODEL DE12TIS SUFFIX ECIEB
DAEWOO FOR USE S420LC-V
INJ.PUMP BODY GOVERNOR
INJ. ORDER 1-5-3--6-2-4 (DRIVE SIDE) PHASING 0-60-120-180-240-300
2
OPENING PRESSURE:1st 160kgf/cm
NOZZLE & HOLDER ASS'Y 105780-8460 2nd 220kgf/cm2
(A) STANDARD
CONDITION INJECTION PIPE(I_D, O_D, L) dia8.0×dia3.0 - 600 mm dia6.0×dia2.2 - 620 mm
FOR RIG
TEST OIL CALIBRATION OIL TEMPERATURE : 40±5 °C
105025-2240
(B) ENGINE NOZZLE & HOLDER ASS'Y
PARTS 105030-4711
CONDITION
INJECTION PIPE(I_D, L)

RACK DIAGRAM AND SETTING VALUE AT EACH POINT


INJECTION Q'TY ON RIG
CHECK RACK PUMP (mm3/1000ST) PRESS
POINT POSITION SPEED (A) (B) ENGINE
(mm) (RPM) STANDARD PARTS (mmHg)
CONDITION CONDITION
RACK POSITION mm

A R1(11.3) 1000 153±2 - above600


B = 6.1 500 16±15 - 0
C R1+0.4 500 (170) - above600

、
、

NOTCH : APPROX 14

INJECTION PUMP SPEED, rpm

BOOST PRESSURE DEPENDENT FULL-LOAD STOP(BOOST COMPENSATOR SPRING OPERATING POINT)


INJECTION Q'TY ON RIG
CHECK RACK PUMP (mm3/1000ST) PRESS
POINT POSITION SPEED (A) (B) ENGINE
(mm) (RPM) STANDARD PARTS (mmHg)
CONDITION CONDITION
P1 R2(R1+0.4) 500 - - 210
P2 R2-1.2 500 - - 500
- - - - - -
- - - - - -

BCS SPRING : k=0.51kgf/mm

MIN. SPEED 1:1.2


WEIGHT WEIGHT=740g LEVER RATIO(min/max) MAX. SPEED 1:1.2
GOVERNOR SPRING K=7.2kgf/mm PLUNGER dia12, 22+45LEAD

IDLE SPRING K=1.9kgf/mm D/V RETRACTION VOLUME 130mm3/st


2
START SPRING K=0.01kgf/mm D/V OPENING PRESSURE 19.6kgf/cm

BOOST COMPENSATOR SPRING K=0.51kgf/mm D/V SPRING k=0.87kgf/mm

FEED PUMP TIMER -

REMARK DRY WEIGHT


STATIC INJECTION TIMING : BTDC 7°
Kg

You might also like