Li-ion Battery Technology Specification

Customer

Part name Li-ion Battery

Model No ICR18650 2200mAh 3.7V

Serial No

Produce No

-1-
Approval Checked Draft

Bin long Jing yin Xiaojun Nie

Customer
Approval

Company address: 7th Floor，block B, Yicheng Huanzhi center, Renmin

Road, Longhua District, Shenzhen，China.
（Tel）： +86-755-86670646
（Fax）：+86-755-86670609
E-mail： sales@pknergy.com Website： http://www.pknergy.com

-1- If manufacturer want to modify the product technology specification, we won’t inform you additionally)
 History of specification

Date Contents Modified by Remarks

20210201

-2-

-2- If manufacturer want to modify the product technology specification, we won’t inform you additionally)
1. SCOPE
This specification governs the performance of the following pknergy Li-ion battery
Cylindrical Cell and its stack-up batteries.

2.SPECIFICATION
No. Item Characteristics Remarks
Minimum: 2090mAh Standard discharge
1 Nominal Capacity （0.2C)
Typical: 2200mAh after Standard charge
2 Nominal Voltage 3.7V —
Charging Cut-off —
3 4.2V
Voltage
Discharge Cut-off —
4 3.0V
Voltage
Constant Current 0.2C
Charge Time : Approx
5 Standard Charge Constant Voltage 4.2V 8.0h
0.01 C cut-off
Maximum Constant
6 2000mA —
Charging Current
Discharge at 0.2C to
7 Standard Discharge —
3.0V
Maximum Continuous
8 3000mA —
Discharging Current -3-

Operating Charge 0～45℃

9 —
Temperature Discharge –20～60℃
-20～45℃ for 1Month
10 Storage Temperature —
-10～35℃ for 6Months
11 Storage Voltage 3.7-3.85V —
If the materials of the
product and packaging
12 Environmental request RoHS accord with RoHS
standard，there will be a
RoHS Id on the box.

3. Dimensions
Please refer the drawing in appendix.

4. Appearance
No scratches, dirt, defect, leakage of electrolyte or gassing should be observed
as a new product.

5. Standard Testing Environment

Temperature : 25±2℃
Relative humidity : 65±20%（unless specially requested）

-3- If manufacturer want to modify the product technology specification, we won’t inform you additionally)
6. Characteristics

6.1 Electrochemical performance characteristics

No. Item Testing Method Requirements
CCCV or Constant current charge to 4.2V
Fully Charged @0.2C follow by a constant voltage holding
1 —
State at 4.2V until current drops below 22±2mA.
0.2C CCCV 0.01c at 4.2V (per 6.1.1) at
room temp. (20±5C), rest for 1-2 hrs then
Rated discharge at a constant current of 0.2C to
2 ≥2090mAh
Capacity 3.0V, testing will be terminated by either 5
cycles or any one discharge time exceeds
10 hrs
Discharge to 3.0V @0.2C, then 0.2C CCCV
0.01C charge to 4.2V, rest for 10 min.
Cycle Life discharge @ 0.2C to 3.0V and rest for 10
3 Cycle life ≥300
@25℃ min. Continue the charge/discharge
cycles until discharge capacity lower than
80% of rated capacity.
Internal impedance is measured on a 50%
Internal Cell：60mΩ
4 charged battery at 1KHz AC at ambient
Impedance Battery：140mΩ
temperature（20±2）℃
Fully charge cells per 6.1.1, store them at Discharge
Capacity
5 (20±2)℃ for 28 days, then discharge the Capacity≥1760mA- 4 -
Retention
cells to 3.0V at 0.2C. h
High Fully charge cells per 6.1.1, store them at Discharge
6 Temperature (55±2)℃ for 2 hours, then discharge the Capacity≥1760mA
Characteristics cells to 3.0V at 0.2C. h
Low Fully charge cells per 6.1.1, store them at (- Discharge
7 Temperature 10±2)℃ for 16~24 hours, then discharge Capacity≥1320mA
Characteristics the cells to 3.0V at 0.2C. h
Cell Voltage
Check open circuit voltage (OCV) of cells
8 during ≥3.7V
prior to the delivery to customers
Transportation

6.2 Cell Safety characteristic

No. Item Test Method Requirements
No fire
Discharge cells to 2.4V at 0.2C, then
1 Over charge No explosion
charge to 4.45V at 3C and rest for 8 hours.
No leakage
Fully charge cells per 6.1.1, then discharge
No fire
2 Over the battery to 3.0V with 0.2CmA at room
No explosion
discharge temperature, connect with external load of
No leakage
30Ω for 24 hours.
Put a fully charged battery in a forced air No fire
Hot Oven oven and raise the temperature at
3 No explosion
Test
5±2℃/min. to130±2℃ Rest for10 minutes. No leakage

-4- If manufacturer want to modify the product technology specification, we won’t inform you additionally)
6.3 Reliability

No
Item Test Method Requirements
.
Electrochemica
High l
Fully charged per 6.1.1,then rest at 60±2℃ for 2
1 Temperature performance、
Test hours.
visual test not
changed
No appreciable
Low Fully charge cells per 6.1.1, rest at -20±2℃ for 2
alternation
2 Temperature hours. Then the cells are placed at room
electrochemical
Test temperature for 3 hours. ly and visually
Fully charge cells per 6.1.1, rest at 40±2℃ with No appreciable
Humidity 90%～95RH% for 48 hours. Then the cells are alternation
3
Test placed at room temperature to “dry out” for 2 electrochemical
hours. ly and visually
After standard charged, fixed the cell to vibration
table and subjected to vibration cycling that the
No fire
Vibration frequency is to be varied at the rate of 1Hz per
4 No explosion
Test minute between 10Hz an 55Hz, the excursion of
No leakage
the vibration is 1.6mm. The cell shall be vibrated
for 30 minutes per axis of XYZ axes. -5-
No fire
Drop The cell is to be dropped from a height of 1 meter
5 No explosion
Test twice onto concrete ground.
No leakage
After the vibration test, according to X.Y.Z each
battery average three vertical pulse peak No fire
6 Collisions acceleration, the setting for the 100m/s2, every No explosion
minute, 40 ~ 80 collision frequency, pulse duration No leakage
16ms collision frequency ± 10 thousand.
Crush (Fresh, No fire
Crush between two flat plates. Applied force is
7 Fully No explosion
about 13kN(1.72Mpa) for 30min.
charged) No leakage
No explosion,
This test will be placed the battery electric dipole No fire
in the fume hood, short-circuit the anode (total The
Short resistance is not more than 50mΩ lines), monitor temperature
8
Circuit temperature changes, when the battery is low of the surface
temperature dropped to about 10 degrees than of the Cells≤
peak, the end of experiment.
150℃
A 56mm diameter bar is inlayed into the bottom of
Impact(Fresh
a 10kg weight. And the weight is to be dropped No fire
,Fully
9 from a height of 1m onto a sample battery and No explosion
charged)
then the bar will be across the center of the No leakage
sample.

-5- If manufacturer want to modify the product technology specification, we won’t inform you additionally)
 Thermal
No fire
shock(Fresh, Batteries in hot box Temperature in
10 No explosion
Fully 5℃±2℃/min，rising to 50℃±2℃ keep 30min
No leakage
charged)
After Standard charge of battery, Will a battery No obvious
deformation,
into 40℃±2℃, Relative humidity90%～95% At
Constant hands rust,
constant temperature and humidity box after 48h smoke,
11 damp
Battery will in environmental temperature 20±5℃ explosion,
performance
Aside 2h, 0.2C to terminate discharge current discharge time
voltage, ≥36 min

7. Warranty
Warranty period for this product is 1 years starting from the date when the
products left the door of manufacturer.

8. Liability
The user has to operate the products according to the instructions printed on the
battery label or follow the advices described in this “Product Specification for
Lithium Ion Batteries published by shenzhen pknergy energy Co., Limited. In
case the battery were overheated or even catch fire or explosion caused by
mishandling of the user side, shenzhen pknergy energy Co., Limited. will not be
liable for the lose caused by any of such mishandling. shenzhen pknergy energy
Co., Limited. will notify the users in written form if any modifications in
-6-
specification, raw material, production process control.

9. Battery Packing Label

The following warnings should be indicated on the battery pack labels.
 Use a specified charger.
 Do not throw the battery into fire, or heat.
 Do not short-circuit the battery terminals.
 Do not disassemble the battery.

10. Warnings and Cautions in Handling the Lithium-ion Battery
To prevent potential leaking, overheating or explosion of batteries please be
advised to take following precautions:
WARNINGS!
 Do not immerse the battery in water or seawater, and keep the battery in a cool
dry environment during stands by period.
 Do not use or leave the battery near a heat source such as fire or heater.
 When recharging, use the battery charger specifically for that purpose.
 Do not reverse the position (+) and negative (-) terminals.
 Do not connect the battery to an electrical outlet.
 Do not dispose the battery in fire or heat.
 Do not short-circuit the battery by directly connecting the positive (+) and
negative (-) terminal with metal objects such as wire.

-6- If manufacturer want to modify the product technology specification, we won’t inform you additionally)
  Do not transport or store the battery together with metal objects such as
necklaces, hairpins etc.
 Do not strike or throw the battery against hard surface.
 Do not directly solder the battery and pierce the battery with a nail or other
sharp object.
 Outer metal conduct can not contact the aluminum layer in AL laminate film,
especially with electrification ,which will be “black spot ”and swelling easily.
 Do not use sharp things to hit the battery.
CAUTIONS!
 Do not use or leave the battery at very high temperature (for example, at
strong direct sunlight or in a vehicle in extremely hot weather). Otherwise, it
can overheat or fire or its performance will be degenerate and its service life
will be shortened.
 Do not use it in a location where static electricity is rich, otherwise, the safety
devices may be damaged, causing a harmful situation.
 In case the electrolyte get into the eyes due to the leakage of battery, do not
rub the eyes! Rinse the eyes with clean running water, and seek medical
attention immediately. Otherwise, it may injure eyes or cause a loss of sight.
 If the battery gives off an odor, generates heat, becomes discolored or
deformed, or in any way appear abnormal during use, recharging or storage,
immediately remove it from the device or battery charger and place it in a
contained vessel such as a metal box.
 In case the battery terminals are contaminated, clean the terminals with a dry
cloth before use. Otherwise power failure or charge failure may occur due to - 7 -
the poor connection between the battery and the electronic circuitry of the
instrument.
 Be aware discarded batteries may cause fire, tape the battery terminals to
insulate them before disposal.

-7- If manufacturer want to modify the product technology specification, we won’t inform you additionally)
11．Protection board principle diagram

12. Protection board component

Description QTY
Item Part Name

1 U1 S-8261DAZ-M6T1U 1pcs

2 U2/U3 8205 2pcs

3 R1 SMD 470Ω±5% 1pcs

4 R2 SMD 2KΩ±5% 1pcs

-8-

5 C1 SMD 0.1μF±20% 1pcs

13.Protection board electrical properties

Items Criteria Unit

No

Overcharge Detection Voltage 4.275±0.025V V

1
Overdischarge Detection
2.5±0.05V V
2 Voltage

3 Overcurrent Detection current 4.5-9 A

4 Supply current ≤8.0 uA

-8- If manufacturer want to modify the product technology specification, we won’t inform you additionally)
14．Dimensions

-9-

……..END……..

-9- If manufacturer want to modify the product technology specification, we won’t inform you additionally)