2

CONTENTS
CONTENTS
PREFACE
1.0 OVERVIEW
1.1 WAYPOINT LISTS
1.2 BUILDING SIDS and STARS
1.3 OFFICIAL CHARTS
1.4 ONLINE FLIGHT PLANNING
1.5 CHOOSING YOUR PROCEDURES
1.6 PUTTING IT ALL TOGETHER
2. 0 HARDWARE INTERFACE
2.1 MCDU SCREEN
2.2 SCRATCHPAD
2.3 FUNCTION KEYS
2.4 INIT
2.5 PREV / NEXT
2.6 CLR
2.7 DIRECT TO
2.8 EXEC
2.9 PLUS / MINUS (+/-)
2.10 AIRP / VOR / NDB / FIX / (LATLON)
2.11 RADIO
2.12 SELECTOR KNOB
2.13 DATA ENTRY KEYS
2.14 DIRECT KEYBOARD ENTRY (DKE)
3.0 MCDU PAGES
3.1 RADIO 1 and RADIO 2
3.2 INDEX
3.3 STATUS
3.4 DEPARTURE / ARRIVAL
3.5 SID/STAR EDIT
3.5.1 ALTITUDE CONSTRAINTS
3.6 ADD RTE WPTS
3.6.1 MCDU WARNINGS FOR EDITING
3.7 ROUTE EDIT
3.8 AUTOPILOT

3
 3.9 PROGRESS
3.9.1 PROGRESS 1
3.9.2 PROGRESS 2
3.9.3 FLT PLAN
3.10 LOAD
3.11 SAVE
3.12 PERFORMANCE
3.12.1 PERF 1
3.12.2 PERF 2
3.12.3 PERF 3
4. 0 FMS FLIGHT PLANNING USAGE
4.1 DEMO
4.2 AMPLIFIED CHECKLIST
4.3 FLT PLAN REVIEW
4.4 WAYPOINT SELECTOR KNOB
4.5 EDITING SCENARIOS
4.6 ROUTE ENDPOINTS
4.7 ADDING / EDITING WAYPOINTS
4.8 AIRWAYS
4. 9 LIMITATIONS
4.10 EDITING: ADDING WAYPOINTS
4.11 EDITING: AIRP, VOR, NDB & FIX
4.12 EDITING: LAT/LON
4.13 EDITING: ALL TYPES
4.14 ADDING VS. EDITING
5​.0 ​IN FLIGHT FMS USAGE
5.1 ​PREFLIGHT
5.2 TAXI AND TAKEOFF
5.3 CLIMB
5.4 CRUISE
5.5 DESCENT
5.6 LANDING, MISSED APPROACH
6​.0 KNOWN LIMITATIONS, HELPFUL TIPS AND ADVICE
6​.1 ​KNOWN LIMITATIONS
6​.2 TIPS and ADVICE
6​.3 WHY IS A SID/STAR NOT AVAILABLE?
7​.0 FMS TUTORIAL VIDEOS

4
 PREFACE

​ ekton FMS, by Steve Wilson. This custom FMS is a

The X-Crafts E-175 addon employs the T
somewhat unique design that is not as challenging as the very detailed and more capable MCDU's
​ ekton FMS is primarily an interface to add, create and edit
found in today's modern airliners. The T
the components of any normal, commercial airliner flight plan, and should take users new to
complex flight planning several steps beyond basic, simplistic FMS route entry.

The update of the ​Tekton FMS offered in the X-Crafts E-195 version 2.0 is also intended to provide
a more in-depth flight planning and flight management experience, one that completes the task of
providing an FMS experience that occupies the middle ground between the stock X-Plane FMS
and more expensive payware aircraft systems.

Note that it is still possible to use the basic X-Plane 10 FMS aside from the Tekton FMS while you
are getting used to the E-195 aircraft if you are uncomfortable with a more complex user
experience. You can switch between these two by clicking on the button in the top left corner of
the Pop-up FMS, and the stock X-Plane FMS CDU is present towards the rear of the center
console.

5
1.0 OVERVIEW
Think of a flight plan as a list of geographical locations, or waypoints, defined by latitude, longitude
and altitude. In modern commercial aviation, the flight plan is normally composed of three primary
elements: the SID, the ROUTE and the STAR. A SID is like a ramp leading up to a super
highway, a ROUTE is like a highway in the sky, and a STAR is your "off ramp" once you've
reached your destination. SID is an acronym that stands for “Standard Instrument Departure.”
STAR stands for “Standard Terminal Arrival Route.”

1.1 WAYPOINT LISTS

The Tekton FMS uses three separate lists to build a flight plan (FLT PLAN), which pertain to the
three primary elements of a typical flight. These are the SID procedure waypoint list, the ROUTE
waypoint list, and the STAR procedure waypoint list.

All three are simply lists of waypoints corresponding to a standard instrument departure from an
airport, the waypoints that we've planned to fly from one airport to another, and finally the waypoint
list for our standard terminal arrival route procedure.

1.2 BUILDING SIDS and STARS

The SID and STAR are built using departure and transition for the SID, and the STAR is
assembled from FINAL approach and approach transition, and/or a STAR arrival, all depending on
the manner appropriate for a given airport.

1.3 OFFICIAL CHARTS

To prepare for one's flight, one uses various official charts to plan their route, as well as departure
and approach documentation for their airport of origin and their destination. The charts will give
you a means to identify a list of waypoints that you will manually enter into the MCDU using the
ADD RTE WPTS page.

A word of caution here. Reading and understanding departure and arrival charts is essential to
successfully using any FMS that provides departure and arrival procedures facilities. It is very
easy to compose a combination of waypoints that make no logical sense when combined with your
planned flight route. Understanding how SIDs and ROUTEs and STARs link together is essential,
and you should expect to have to learn how to employ this published information as you learn to

6
use the custom MCDU provided with this custom FMS. It is possible to create seriously
inconsistent flight paths with STAR functionality. Part of being an aviator is knowledgeable
planning.

1.4 ONLINE FLIGHT PLANNING

An alternative to manually entered waypoints would be to use an online flight planner to choose
your route waypoints. These facilities give you the ability to download your route as a .fms file that
X-Plane will understand. Once downloaded, you manually place these in your
X-Plane/output/Flight Plans folder. Note that this is mainly for your route - not airport to airport.
While such flight plans can be loaded by the FMS, doing so eliminates the ability to easily use
departure and arrival procedures. Flight plans with airports at the endpoints cannot be used with
SID’s and STAR’s without significant editing, and they will also not properly function with fuel
planning in the PERFORMANCE pages unless edited so that they can be merged with SID’s
and/or STAR’s.

1.5 CHOOSING YOUR PROCEDURES

The departure and approach documents you use will help familiarize you with what is available.
You choose a departure SID based on the winds and what you know to be the active runway for
your airport of origin. This is subject to ATC direction, naturally.

Similarly, you select a STAR for your destination or "ARRIVAL" airport. This selection is your best
guess during the planning phase. You can request a STAR on arrival, but it's up to ATC to clear
your selection. It is possible to change your STAR dynamically and re-EXECute your flight plan to
conform with the clearances you’re given as you near your destination, all while remaining on
autopilot.

1.6 PUTTING IT ALL TOGETHER

After you've completed selecting your procedures and your route, you then have all of the
elements of a complete flight plan. All that remains is to combine these three lists into one so that
you can execute your plan. Note that if the endpoints of your SID, ROUTE and STAR are within 3
miles of each other, the EXEC function of the MCDU will merge your ROUTE endpoint(s) as
needed with the appropriate SID and/or STAR waypoint. This is because leg lengths shorter than
3 miles are impractical.

7
2. 0 HARDWARE INTERFACE
2.1 MCDU SCREEN
The main body of the MCDU (Multipurpose Control Display Unit) is similar to most that you may
have already been exposed to, including the rather simple MCDU used by the stock X-Plane FMS
Instrument.

There is an upper screen with six buttons on each side, and these are identified as L1 to L6 on the
left, and R1 to R6 on the right.

A video screen capable of displaying various color text data lays in between these buttons, and up
to 14 rows of text are displayed on 17 unique data pages in addition to the INDEX page.
Additional display pages for lists of waypoints or loadable flight plans are provided when the entry
counts exceed 9 or 10 per page, depending on the data being displayed.

8
2.2 SCRATCHPAD
The bottom row of this display will show the SCRATCHPAD, but only when it is available. All data
to be entered first appears here, prior to being "injected" into various data fields using the buttons
on either side of the MDCU screen.

Just above the SCRATCHPAD is a system message area. This provides instant feedback on both
successful data entry or function selection, as well as a number of warnings when appropriate.
Pay attention to this area when entering data to avoid unexpected results.

9
2.3 FUNCTION KEYS
Below the screen are two rows of special function keys. Note that the RADIO button is the only
means of reaching the radio pages.

10
2.4 INIT
Initializes the X-Plane navigation database and resets the FLT PLAN waypoint counter to zero.
When beginning a flight planning session with the FMS, this is the first key you should press. Use
with care if you’re in flight, if at all. This function is only available on the MDCU and FLT PLAN
pages. Use in flight could see your aircraft turn for the departure airport when a new flight plan is
loaded and the autopilot is still engaged. See Section 5.0.

2.5 PREV / NEXT

At present, these are only for paging through lists of data when such lists are greater than 9 or 10
items per page, depending on what's being displayed. If a waypoint detail page is created for the
active flight plan at some point, these will also perform a waypoint list navigation function.

2.6 CLR
This button is functional on the SID, ROUTE and STAR EDIT pages, as well as the MCDU INDEX.
It’s used to clear the list entries so that you can re-enter data or other need, as the situation
dictates. There is no “undo” function. Once the list is gone, it’s gone permanently, and any and all
data needed, if any, would need to be reloaded. Note that it’s necessary to press CLR twice to
completely clear the STAR waypoint list to zero. The first use restores the default arrival waypoints
for reuse during flight.

Users can completely clear all entries in the SID, ROUTE and STAR waypoint lists as well as all
departure and arrival airport selections by using the CLR button when at the MCDU INDEX page.
As this is a powerful capability, you must press the CLR button twice within five seconds to
successfully clear entries. A reminder of this need is presented in the warning area on the first
press of the CLR key.

While using CLR to reset the FMS can be used if needed to start with a clean slate, the primary
purpose is to prepare the FMS for a subsequent flight where neither X-Plane nor the aircraft are
reloaded, simulating a very real scenario for an airline pilot’s flying duty day. Therefore, when CLR
is pressed, the FMS is cleared and the MCDU display is automatically returned to the RADIO
page.

11
12
2.7 DIRECT TO
This is the arrow pointing to the right. Performs the DIRECT TO function when viewing an active
flight plan (FLT PLAN).

2.8 EXEC
If there is data in any combination of SID, ROUTE or STAR waypoint lists, the lists are merged into
a FLT PLAN and loaded into the X-Plane navigation database. Note that the ends of the ROUTE
will be merged with the ends of the SID or STAR if these points are within approximately 3 miles of
each other. This function is only available on the MDCU and FLT PLAN pages. You have the
ability to re-EXECute and revise the STAR data that has already been loaded if ATC clears you to
a different set of terminal procedures. Otherwise, EXEC is no longer functional after having been
pressed once and the SID, ROUTE and STAR data has been loaded into the FLT PLAN. In order
to re-load, INIT must be pressed first.

2.9 PLUS / MINUS (+/-)

This key will change the sign of numeric data on the scratchpad. This is only available on the
ROUTE WAYPOINT page at present, and will also be available on editing pages in the future. It is
only useful in entering LAT/LON data. Note that you can also enter a WEST longitude or a
SOUTH latitude by beginning your entry with a minus sign (hyphen).

2.10 AIRP / VOR / NDB / FIX / (LATLON)

These five buttons are only active on the NEW ROUTE WPT and EDIT WAYPOINT pages. These
are the five possible types of waypoint to store.

2.11 RADIO
This button is a shortcut to the radio page so that you can quickly digitally enter a frequency and
manage active frequencies, transponder and IDENT. This is currently the only way to enter
8.33khz radio channels. NOTE: If you are editing anything, it's lost. There are no exit checks for
either adding a new waypoint or editing an existing waypoints. The theory here is that if you need
the radio page, you need it immediately in order to handle an ATC directive. As mentioned, this
button is the only means of access to the RADIO functions of the FMS.

13
2.12 SELECTOR KNOB

On the real ERJ-195, this knob is used to tune radios. In this Tekton FMS MCDU, it's used as a
selector spinner and pushbutton. When displaying lists of data, rotations to right will advance a
highlight down the page, rotations to the left will move the highlight up the page. Pressing
(clicking) the smaller center knob selects the item that is currently highlighted.

14
2.13 DATA ENTRY KEYS
Generally self-explanatory. Full alphabet, numbers zero through nine, a decimal key and a
minus(-) key. The left arrow key is the “backspace” key for the SCRATCHPAD, and DEL will
delete anything entered in the SCRATCHPAD.

15
 2.14 DIRECT KEYBOARD ENTRY (DKE)
You can use your computer’s keyboard to make all of your data entry into the SCRATCHPAD.

DKE is initiated by pressing the TAB key. Note that if you have any other X-Plane command mapped
to this key, it will not be effective while you have the E195 loaded. DKE is also exited using a second
press of the TAB key, or the ESC and END keys can be used as well. An alternate means of
entering and exiting DKE is available by clicking in the MCDU screen itself - almost the entire screen
is one rather large hotspot. In the image below, you can see that the mouse pointer has changed to
a pointing finger, indicating that it is over the DKE mode change hotspot.

While in DKE, there is an indicator DOT on all MCDU pages in the top left corner. Additionally, the
cursor will change from a vertical bar to a block cursor.

In DKE, every keystroke is accompanied by a BEEP. This is audible feedback that you are entering
data in DKE mode, and is especially useful as a reminder that you’re in DKE when trying to use your
view keys or other X-Plane commands, and you are not getting the response you’re expecting.

Available data entry keys in DKE include all alphanumerics, the decimal and the minus sign - in
general the same buttons available on the MCDU via mouse click.

16
Function keys in DKE include the up and down arrows, which moves the row highlight up and down,
the left and right arrow keys stand in for the PREV and NEXT buttons, and the ENTER key is used
when making a selection. BACKSPACE works just like in normal typing, and the DELETE key will
clear the SCRATCHPAD.

Aside from the MCDU keys, Page Up and Page Down are also available when viewing the
NAVIGATION PLAN display. They work just like the up and down arrows when viewing the FLT
PLAN, the only difference being that the FLT PLAN page does not need to be open to scan your
loaded waypoints. When FLT PLAN is open, these keys act just like the up and down arrow keys,
keeping the FLT PLAN display in synch with the PLAN display. Note that if you are not in FLT PLAN
while viewing the PLAN display, and enter FLT PLAN, the PLAN display will automatically return to
the current destination waypoint that’s highlighted on FLT PLAN. The PLAN view stays in synch with
whatever page and row that is being shown in FLT PLAN.

Using DKE is addictive and convenient, but takes a bit of practice to know when to enter and exit
when you need to do something else in the cockpit. The audible alert is a great training aid in this
regard. Also, a limitation of the X-Plane’s key sniffing capability is that you really can’t type extremely
rapidly. This can produce unexpected results, like character duplication. Typing somewhat
deliberately is a good best practice.

17
3.0 MCDU PAGES
3.1 RADIO 1 and RADIO 2
The RADIO page is now the first page that is presented whenever the aircraft is started from cold
and dark or when the simulation is reset. This conforms to real world E195 FMS behavior. As
previously mentioned, these pages are only accessible via the RADIO button on the MCDU
keyboard.

RADIO 1 gives you control of the COMM1, COMM2, NAV1 and NAV2 radio frequencies, as well
as the transponder functions. This is relatively straightforward. Enter the first three digits, the
decimal point, and then however many further digits are needed to complete the entry. 121.5, for
example, becomes 121.500. Once entered, the buttons next to the arrows pointing up and down
will swap the radio frequency entered into standby with the frequency that is active.

You can only enter an 8.33khz radio frequency using the FMS interface. It is not possible using
the conventional radio panel controls.

You can swap between the active and standby frequencies using the appropriate button. You can
also enter the transponder code and IDENT. As with other pages, digital data is entered to the
SCRATCHPAD and injected using the appropriate left or right screen buttons.

18
The RADIO 2 page gives you access to the ADF functions. It is only available from the RADIO 1
page.

3.2 INDEX
This is the main page that routes you to most of the other pages directly. On this page you see
use of arrows pointing at keys. When you see arrows pointing away from the data and towards a
key, that key is active and will do something for you. If you see arrows pointing inwards, at the
data screen, then SCRATCHPAD data can be "injected" at that entry point.

19
3.3 STATUS
General information about the location of the aircraft, the setting of the autopilot and loaded
ROUTE, SID and STAR waypoint lists. The OAT key will change the display from Celsius to
Fahrenheit.

3.4 DEPARTURE / ARRIVAL

Select an airport by entering the ICAO code in the SCRATCHPAD and then insert it with button
L4. Once you've entered a valid airport, you must then select a runway with button R3. You then
continue to the SID/STAR procedure element selection pages with buttons R4 and R5, and for
STARs only, R6.

There is an order of selection to be followed:

DEPARTURE ARRIVAL

1. Runway 1. Runway

2. SID 2. STAR

3. SID Transition 3. STAR Transition

4. FINAL Approach

A SID transition will require a specific SID to be selected first. Otherwise, all procedure elements
can be selected independently - or not all. As mentioned before, this opens up the possibility of
selecting combinations of procedure legs that are not continuous - in other words, those that do

20
not link together properly. So proper referencing of departure and approach information for the
airports involved is essential for assembling a valid flight path.

Be aware that there are minimal departure and approach waypoints. Once the departure runway
is selected, you will get at least two waypoints in the SID waypoint list: the end of the runway
where you start your takeoff, and a single waypoint that is five miles from that point and 1500 feet
above the runway MSL altitude. These waypoints are automatically replaced when SID and
FINAL approach procedures are selected.

You can reselect any of the procedure elements if you change your mind or make a mistake.
Since SID transitions and STAR approach transitions are dependent on the standard departures
and final approach types, reselecting either the standard departure or final approach will clear the
previous dependent procedure element selection for a SID transition or STAR approach transition.

21
You can reselect any of the procedure elements, or even the airport itself, if you change your
mind or make a mistake. Reselecting an earlier procedure element automatically clears any
subsequent elements that were previously selected.

3.5 SID/STAR EDIT

These pages provide a list of the waypoints generated from the X-Plane GNS430 data files
provided by Laminar research or the custom data files that you acquire from Navigraph or
Aerosoft. This will be where you access the individual waypoints to select them for editing.

Rotate the knob as needed to highlight the desired row by hovering the mouse on either side of
the knob to access the manipulator pop-ups, and click as needed to move the knob. You can also
use the DKE up arrow/down arrow keys.

Use the PREV/NEXT buttons (or DKE left/right arrows) to advance through pages. The last row
will rotate to the first and vice versa. Likewise for navigating the pages. Note that these pages are
only accessible via DEPARTURE/ARRIVAL. They are not displayed on the MCDU INDEX page.
Clicking on the center of the knob will allow you to edit the waypoint selected.

22
3.5.1 ALTITUDE CONSTRAINTS
Procedure altitude constraints are defined as follows:
(5000) - No constraint.
5000 - Hard altitude
5000A - Fly at or above
5000B - Fly at or below
50A/60B - Fly above the first altitude, but below the second. In other words, fly “between.”
When a procedure specifies a “between” or “window” constraint, the value provided to the autopilot
will be the higher number when flying a SID, and the lower altitude when flying a STAR.

Note that when you edit a procedure waypoint, you cannot specify a constraint. The result of
​ t, neither above nor below. This also
editing a constrained altitude is a hard, or fixed altitude: fly a
applies to procedure waypoints that do not have a specified altitude in the available navigation
files. They will initially be entered with an estimated altitude based on typical climb or descent
rates, and will present as “no constraint,” with parenthesis: ​(5000)​. If edited, they become hard
altitudes.

This is a STAR entry for HAWKZ4 - 16L into KSEA - Seattle Tacoma Airport, with only the STAR
selected. Note the V-APP waypoint that is added as a visual approach fix.

23
3.6 ADD RTE WPTS
This page allows you to manually add ROUTE waypoints either to a new plan or to one that you've
loaded. See section 4.8 for more information on Adding and Editing waypoints.

Choose your fix type using the waypoint type buttons, enter an ID....OR....enter a latitude and
longitude. Entries are green when the loaded information is being displayed. Entries turn yellow
when data needs to be saved. The default waypoint type when selecting this page is FIX, but after
that, the last waypoint type used persists to the next blank entry. (DKE mode is active in the
image below).

24
Lat/Lon entry is segregated from fix entry. You can't enter a fix when in Lat/Lon mode, and you
can't enter a Lat/Lon when you're entering data for an airport, VOR, NDB or FIX.

A previous waypoint’s altitude persists to subsequent waypoints. This makes it much easier to
enter a string of ROUTE waypoints at the same altitude.

You also have the ability to add AIRWAY waypoints to your ROUTE. Airways also use the altitude
of the entry waypoint for every entry, easing the process of completing the vertical navigation
properties of your flight plan. Use of the AIRWAYS function is covered in section 4.8.

3.6.1 MCDU WARNINGS FOR EDITING

If you try to save incomplete data, you will be warned that your data is incomplete.

If you try to leave this page with unsaved data, you will be warned that your entries haven't been
saved.

If you've entered less than two waypoints, the system will warn that a route requires two
waypoints.

A second attempt to navigate away from this page following a warning override the warning and
you will lose data. If less than two waypoints have been entered and you leave anyway, you lose
everything, even your first saved waypoint.

25
26
3.7 ROUTE EDIT
See the section on Adding and Editing waypoints. This page operates in a manner similar to the
SID and STAR EDIT pages you visit when building a SID or STAR. This page will show either
waypoints you loaded from an external file, or waypoints added manually.

27
3.8 AUTOPILOT
Here you can quickly enter values much larger or much smaller than are currently selected by
using the digital keypad to enter numeric information into the SCRATCHPAD, and then injecting it
where needed, using buttons L1 through L4 on the left. Only fields that are colored magenta can
be changed using this page. You have the ability to toggle between KIAS and MACH airspeed
entries using the R5 button.

The minus sign (-) only works for the VERTICAL VELOCITY selection in the first field. Anywhere
else in the SCRATCHPAD entry, and you will be informed of an incorrect entry when you try to
inject the data containing it.

The rest of the data displayed is provided to give you a repeater of various current aircraft flight
data and autopilot function status indications as you make your autopilot entries. Note that this
does not replace the top shelf autopilot controls. Either can be used at any time.

28
3.9 PROGRESS
PROGRESS consists of three pages. Progress 1 shows the current progress of the aircraft
through the flight plan, Progress 2 provides detailed waypoint information and minor editing
capability, and FLT PLAN shows the complete flight plan with access to major editing capability.

3.9.1 PROGRESS 1
This page provides similar functionality to other manufacturer’s FMS progress monitoring pages.

The top line shows the waypoint that you’re currently flying towards. The data includes distance
and time to go along with a fuel prediction based on current fuel flow. The second line shows the
same data, but for the way point immediately following the current destination waypoint.

The third line continues this data format, but represents the values one could expect if the current
airspeed and fuel use were to remain in effect all the way to the destination airport. This line will
continue to display the destination airport until on final approach to the airport, and will advance to
the first waypoint of a hold or missed approach guidance if such waypoints have been added in a
final approach procedure.

The fourth and fifth lines give you your current airspeed and TOC/TOD values. TOC and TOD will
go to negative values after they are passed.

29
3.9.2 PROGRESS 2
Initially, this page will always display detailed data for the current waypoint. While active, you can
still edit the altitude, but no other elements. You can jump to the data for a different way point by
typing the desired waypoint into the SCRATCHPAD and inserting it with button L1. Bulk altitude
editing is best accomplished through the FLT PLAN page and the standard waypoint editor
.

30
3.9.3 FLT PLAN
This shows the flight plan after EXEC has been pressed and your waypoint package merged and
injected into the X-Plane navigation database. The first and last waypoint will always be a
LAT/LON waypoint as these are actually the LAT/LON positions of the selected runways'
thresholds.

The bright magenta highlight will advance as the FMS negotiates its way through the flight plan.
You can highlight any field that is later in the route than currently displayed. When such fields are
highlighted, DIRECT TO becomes available for that waypoint. You cannot navigate your selection
back to "used" waypoints. The center button of the knob can be used to select available
waypoints for editing, just as in the SID.

Use of DIRECT TO will update the flight plan as X-Plane replaces your current waypoint
destination with a LAT/LON coordinate, which will precede the waypoint the you have chosen to fly
to directly.

If the highlighted waypoint advances beyond the current page while FLT PLAN is being viewed,
the page will automatically advance to the next page. This also works for the selector knob or the
UP/DOWN arrow keys when in DKE.

With this functionality, using the PLAN view of the NAVIGATION mode is easier, with a relocated
zoom control and information about which waypoint is being viewed. There is also a DKE indicator

31
so that you know if you are in DKE while viewing the PLAN, since you can now scan through your
complete FLT PLAN using Page Up and Page Down.

The Page Up and Page Down keys act similarly to the up and down arrows when viewing the FLT
PLAN page, only the FLT PLAN page does not have to be open to scan the list of loaded
waypoints.

When FLT PLAN is open, these keys act just like the up and down arrow keys, keeping the FLT
PLAN display in synch with the PLAN display. Note that if you are not in FLT PLAN while viewing
the PLAN display, and enter FLT PLAN, the PLAN display will automatically return to the current
destination waypoint that’s highlighted on FLT PLAN. The PLAN view stays in synch with
whatever page and row that is being shown in FLT PLAN, as long as that page is open on the
MCDU.

You use the down key or page down to advance, and the up key or page up to go back. This
clearly reversed from what would seem logical, until we remember that the main purpose of the
up/down keys in DKE is to move the row selector up and down when viewing a page with
selectable rows. And in this case, down happens to be heading towards the end of the flight plan.

32
3.10 LOAD
This gives you a list of the files in your X-Plane /output/Flight Plans directory. Many pages of
entries are possible.

​ 8
NOTE:​ The width of the page only permits just so many characters to display. You get 2
characters ​for flight plan file names. If any files are found by the FMS that have names longer
than this, not including the file extension, they are not included in the list. A file named
FMS_File_Loader_Report.txt is created every time you go into this page, and it contains a list of
the .fms files that have been rejected.

33
3.11 SAVE
Replace "ENTER A FILENAME" with the text of your choice, up to 28 characters. It the filename
already exists, you'll get a warning when you try to save. Repeat the save command (button R6) if
you want to override.

34
3.12 PERFORMANCE
Performance remains a “lite” experience in the Tekton FMS, it does hit upon many of the features
of more complex FMS offerings. In these pages you will manage your aircraft’s weight and
balance, fuel quantity and usage, and other configuration options.

3.12.1 PERF 1
Your first visit to the PERF 1 page will activate the V-speed audible takeoff callouts, which are
configured on this page. Even if you make no entries at all, you will at least get the default values.
However, if you correctly adjust your payload, fuel, intended flap setting and trim, these speeds will
more closely reflect the correct values. Trim is a function of the aircraft’s center of gravity, and you
can enter either a specific CG value, or the distance from the forward point of the Mean
Aerodynamic Chord (MAC), expressed as a percentage of the total length of the MAC. Slight
adjustments in the CG location of the E195 have been made, and the CG position is now
dynamically managed with the selection of either the default or the long range winglets option.
The PERF 1 page will also reflect which option has been selected. You’ll see ​(EWT)​if the
extended range wingtips have been selected. Finally, PERF 1 gives you control over the units of
measure used, either Imperial or Metric.

35
3.12.2 PERF 2
PERF 2 is where the FMS now becomes rather demanding of complete flight plan entries,
including altitudes. The whole purpose of PERF 2 is to provide a rough estimate of the total time
enroute to your destination, how much time it will take, and how much fuel you will use plus one
hour’s fuel flying at 200 KIAS and 3000’ AGL for a worst case hold pattern scenario. The
mandatory entries for this page to calculate these values are at the least a departure and arrival
airport. Since we always have at least two waypoints now in a SID and STAR with these two
selections, and these waypoints always have altitudes, this satisfies the SID/ROUTE/STAR
requirements. However, the fuel used would be extreme, since the average altitude would be very
low. So adding a ROUTE with correct altitudes for initial and final intended cruise altitudes, as well
as all altitudes in between is a best practice. You cannot override the average altitude value used
for your ROUTE fuel calculations, and you have to be sure that you have an altitude entry for
every waypoint.

Likely the first entry you will make on this page will be your intended airspeed or Mach during the
cruise phase of your flight at altitude. If you are flying at or above FL300, you must enter a Mach
number since that is above the transition altitude we are now using for the E195. While this
altitude value will sometimes change in practice, the complexities that would add to the fuel
calculations are such that it is prudent to use a fixed value instead to ensure reliability and relative
simplicity when using the FMS.

36
While you see INITIAL CRZ and FINAL CRZ value entries, which are required for overall fuel
calculation, these have no effect on ROUTE fuel calculations. They only impact the calculations
for top of climb (TOC) and top of descent (TOD) distance values that are shown on the
PROGRESS 1 page.

If you’ve entered all of your waypoint data before reaching PERF 2, you will get a warning to enter
your cruise altitude. When you’ve entered that value, you will then get a warning to enter your
initial and final cruise altitudes. Entering either will mirror over to the other automatically, since
many times they are the same. Either value can be overridden, however. After these values have
been entered, you should get a complete fuel calculation. If anything is missing, you’ll be warned,
as the PERF 2 page fuel calculations are attempted and/or revised with every entry on the page,
as well as when you enter the page from either PERF 1 or PERF 3.

Finally, there is a complete breakdown of the your fuel usage selections and calculation saved to
file every time you make an entry on the PERF 2 page. This is saved in the E195 aircraft folder,
and it is named ​FMS_File_Loader_Report.txt​.

Entering winds aloft and anticipated outside air temperature (OAT), averaged for your route, will
also initiate a recalculation of distance, fuel and time, as these values also can impact fuel use and
time enroute.

37
3.12.3 PERF 3
PERF 3 deals with the approach phase of your flight, and will give V-speed recommendations
based on the calculated initial approach weight at the end of your ROUTE. These speeds are
optionally adjusted for icing conditions. The calculated weight amount can be overridden. To
revert to the calculated value, press the L1 key again without any value entered in the
SCRATCHPAD.

38
4. 0 FMS FLIGHT PLANNING USAGE

4.1 DEMO
See the ​‘...Embraer E195/Documents/Demo flight’​ folder for a sample flight that will give you the
experience of a complete flight, taking off and landing at Tucson International Airport. Something
of a "once around the pattern" flight, only with 17 waypoints. It will give you the full experience of
the flight management functions of the MCDU in around an hour.

4.2 AMPLIFIED CHECKLIST

Presuming that you've reviewed your charts and procedure documents, and are sitting in the
aircraft powered up, here's a sequence of entries that should get you ready to go. Refer to the
images on the previous pages if needed:

1. Select PERF 2 and enter your CRUISE AIRSPEED/MACH, INIT CRZ ALT and FNL CRZ ALT.
The cruise altitudes will limit procedure auto-calculated altitudes if less than 30,000 feet.

2. Select DEPARTURE. Enter this data using direct keyboard entry (DKE) mode if desired.

3. Enter the ICAO identifier of your departure airport in the SCRATCHPAD and inject it using
button L2.

4. Select your runway. Either rotate the selector knob up and down to move through the
selections, or use the up and down arrows if in DKE mode.

5. Select your departure from the list of those available for your runway. If none are available
due to procedures that must be eliminated due to waypoints not currently supported, you may
omit the departure. You will always get a single waypoint at 5 miles and 3000 feet above the
departure runway threshold altitude if no procedures are selected. This will appear as V-DEP
in the waypoint list, indicating a non-standard visual departure.

6. Select your transition. Use the PREV and NEXT keys below the screen to change pages as
needed, or the left and right arrows if using DKE mode. Transition selection is optional.

39
7. After selection, you may proceed to the SID edit page where you may review the waypoints,
and in particular you may use the waypoint editor to add waypoints or trim as needed. You
will also use the SID edit page to assess and possibly edit predicted altitudes that are
unconstrained. All altitudes are provided.

8. Return to the MCDU Index and select SID Edit to view the list of waypoints to visually confirm
loading.

9. Return to the MCDU Index, and repeat steps 1 through 7, but use the ARRIVAL and STAR
related functions instead, which are nearly identical.

With STARs you select your runway first, just like SIDs. This filters out any procedures that
do not apply to this runway.

As with our earlier sample of waypoint editing, the above entries show what it looks like to
use DKE - direct keyboard entry. Since the mouse cursor is over the display area, you can
see that it changes to a pointing finger. This is shows that the area is a touch hot spot to
toggle in and out of DKE mode. You can also see the block cursor in the SCRATCHPAD,
and the indicator dot in the upper left that shows you’re in DKE.

40
Selecting the runway.

The next thing that you need to do is to decide on your method of approach, which is what
you’ll request from ATC. The most complex solution will be described.

41
Step 1.​ Choose STAR on the ARRIVAL page. This will present a list of STARs.

Step 2.​ Choose an approach transition (APPR TRANS). This will list all of the transitions
that are available to the runway you’ve chosen. Each will be listed with the runway ID, and
​ I11L” ​is an ILS approach to runway 11L.
that is preceded with a letter. For example: “
These are the possible approach types you will see, as defined by the first letter in the
runway shown:
C - CAT II ILS Approach
I - ILS Approach
G - GPS/RNAV Approach
D - VOR/DME Approach
N - NDB/DME Approach

42
(Please see section 6 for important special notes regarding procedures instruction steps
and the resulting waypoint).

Step 3:​ Select your APPROACH from the list offered. ​Extra care is needed here since
you will see every available approach​. This is where proper planning with approach plates
and other documentation is paramount to ensure you don’t get a flight path that backtracks
or goes in unexpected directions.

When you select STAR transition, or a STAR, and/or an approach transition, the threshold
coordinates for your arrival runway are appended automatically to your STAR waypoint list.
When you select a FINAL, this is not done since it is typical that missed approach or hold
waypoints may also be in the procedure, and would conflict with a final waypoint at the end
of the arrival runway.

Different selections may make differences in the waypoints provided. Carefully review the
results of your selections on the STAR EDIT page to determine if the route loaded is the
route you desire, referring to your airport's procedure documents. Be sure to compare
these results with your approach charts and documents.

If you don’t select an APPROACH, a single visual approach waypoint will be automatically
added five miles and 3,000 feet above the destination runway. This will appear as V-APP
in the waypoint list.

43
10. Enter your ROUTE

OPTION 1: Select the ADD RTE WPTS page and manually enter your route's waypoints.
This can include entering even as much as one route waypoint, followed by an AIRWAY
selection set. (A more complete description of both follows later in this document). Note
that as long as you enter an altitude for a waypoint, that altitude will persist to the
waypoints that follow, whether individually or in an airway waypoint set.

OPTION 2: Select the LOAD page and choose a route file that you previously created or
that you downloaded from an online flight planner. Only .fms files are offered here. When
creating these route files in your favorite flight planner, be very sure to enter the altitudes.
​ lot more
If you don’t, you’ll need to add them in the waypoint editor, which is likely a
tedious.

NOTE:​ If a file you put in the X-Plane/output/Flight Plans directory doesn't show up here,
chances are the filename was too long. You can confirm this by opening the
FMS_File_Loader_Report.txt that is always created every time you fly the E195. If the file
you want is reported here, you can edit the filename to be shorter. Exiting the LOAD page
and re-selecting it will recreate the list of available flight plan files. If you've shortened the
name enough, the file will then be available.

11. Selection of the file to load is identical to selecting a SID and STAR as you did earlier. Use
the PREV/NEXT buttons as needed, or the up and down arrows if in DKE, and the outer ring
of the selector knob to highlight the file you want when you've found the correct page. The
center button of the selector will load the file into the ROUTE waypoint list.

12. At this point, you have the three lists you need to load a full flight plan into the X-Plane
navigation database. But DON’T LOAD IT YET. (That is, don’t press the EXEC key).

It's worth mentioning that you don't have to have all three lists. Any combination of
SID/ROUTE/STAR will load. All it takes is two waypoints to make a valid FLT PLAN. A SID
and a STAR will yield a FLT plan that takes you from the end of your SID to the beginning of
your STAR. Similarly, if you've created a ROUTE online that already incorporates departure

44
 and approach waypoints, you can load that file and immediately execute it without even
considering SID or STAR procedures.

12. Verify your SID/ROUTE/STAR waypoint lists using the SID EDIT, ROUTE EDIT and STAR
EDIT pages. Additionally, the file you loaded as well as the procedure selections will appear
on the STATUS page. Be sure to review and adjust the unconstrained altitudes as needed.

13. Once you're satisfied with your lists, at this point you return to the MCDU INDEX page and
press the INIT button if you haven’t already.

14. Now go into PERF 1. Edit your payload weight and your fuel. Adjust CG or MAC% as
needed. Select the flap setting that is appropriate for your weight and runway length. (Be the
aviator here and use your best judgment. FLAPS 2 is a good default value for many
situations). This will tell you what trim setting you need, so you can use the trim indicator
along with the suggested trim indication to set your trim. One less thing to do later.

15. Go back to PERF 2. Since all of your departure, arrival and altitude information has been
entered, you’ll get your fuel calculation results at this point. If you don’t, you’ll get a warning
message as to what’s missing. Note that PERF 3 has no effect on fuel calculations, and is
more useful while enroute as a reference. This is, however, a good time to exit DKE since
there are no other entries to make, if you’re in that mode. If you keep hearing beeps after
you’re done with the flight planning, and you can’t seem to get any other X-Plane command to
work - just press TAB, ESC or END. It’s easy to forget.

16. Now you can return to the MCDU INDEX and Press the EXEC button to merge and load your
three lists of waypoints into the X-Plane navigation database. At this point, the endpoints are
merged as needed and a FLT PLAN is created. Hitting EXEC a second time (or third, fourth,
fifth, etc.) is going to result in a warning that the flight plan has not been initialized (with INIT).
This is to prevent corruption of your flight plan. You cannot change your SID or ROUTE
information and just hit EXEC. There are special procedures for this if you absolutely must
edit your route so completely in section 5.2..

17. One important feature available in flight is the ability completely reselect your terminal
procedures. If ATC gives you a different STAR, TRANSITION or APPROACH, any changes

45
 you make on the DEPARTURE page can be loaded into the active flight plan by hitting EXEC
again.

Finally, be aware that after you’ve EXECuted your FLT PLAN, changes are locked out in
PERF 2. So make sure your flight plan is complete and absolutely correct before working on
your fuel calculations. PERF 2 is a preflight tool only.

4.3 FLT PLAN REVIEW

You can view the completed plan using the FLT PLAN page. The FLT PLAN page will also keep
track of the waypoint that the aircraft is flying to when you’re not watching PROGRESS 1. As with
any of the list based MCDU functions, you can use the PREV/NEXT buttons to advance through
the various pages of the FLT PLAN.

46
4.4 WAYPOINT SELECTOR KNOB
You use the selector knob to highlight waypoints that you haven't flown past yet. You cannot
select waypoints that you've already visited -- that is, any waypoint that appears above the
magenta highlighted waypoint. The purpose of the selector knob is mainly to allow you to edit
waypoint data. If you're cleared to a different altitude, you would edit it here. Clicking on the
center of the selector knob will bring you to the editing page. Once editing is completed, an
update will have the effect of changing the data in the X-Plane navigation database. This does not
change the entries in any of the source lists - SID, ROUTE or STAR. You can edit the the
waypoint you're flying to as well.

Be sure to remember that the up and down arrows also move the selector knob in DKE mode.

4.5 EDITING SCENARIOS

There are three scenarios where editing FLT PLAN waypoints while enroute may be needed:

● Deviation due to weather

● Deviation due to diversion to an alternate destination.
● Substituting a new STAR.

Deviations due to weather are best handled by edits to the FLT PLAN.

Deviations for diversion to a different destination airport or the substitution of a different STAR than
the one you loaded originally would require changing the STAR and reEXECuting.

One FLT PLAN edit that requires no special handling is the change of a SID, should ATC direct
you differently than you planned. In this case, simply navigate to the DEPARTURE page, then the
SID SELECT page, and reselect your SID. Be sure to review your ROUTE waypoints if the SID
takes you in a direction that doesn't blend well with the original ROUTE. Edit the start of the
ROUTE as needed. Then re-EXECute after pressing INIT once again.

4.6 ROUTE ENDPOINTS

Find the endpoints of your optimal SID/STAR selections before you create your ROUTE. This is
CRITICAL. Be sure to accommodate any turns from the end of your SID to the ROUTE and the
end of your ROUTE to the STAR. If you download ROUTE .fms files from the web, be certain that

47
they do NOT include the departure or arrival airport. It makes no sense to fly a perfectly good
procedure, only to then return to the airport. This also may have the effect of drawing a rather
unexpected flight path on your NAV display.

4.7 ADDING / EDITING WAYPOINTS

The ADD RTE WPT page is nearly identical to the EDIT WAYPOINT page that you can only reach
after selecting a waypoint from SID, ROUTE, STAR or FLT PLAN edit pages. The only difference
is that you can only save a new waypoint when it's entered. With the EDIT WAYPOINT page, you
can update a waypoint, insert the edited waypoint before the waypoint you originally selected,
insert the edited waypoint after the waypoint you originally selected...or, of course, you can just
delete the selected waypoint. Observe that unedited waypoints have all green entries on screen,
and if you’ve made a change, the entries turn yellow.

4.8 AIRWAYS
One way to add a lot of waypoints all at once is to use AIRWAYS. Basically an AIRWAY is a set
of waypoints that connect airports, fixes and navaids in a set sequence. Think of them as
“highways in the sky.” To use AIRWAYS, you will need to refer to appropriate low or high level
charts. You will want to know where you want to enter the airway, and where you want to exit.
These two waypoints can coincide with SID/STAR waypoints in some cases. If they do not, for
your route you will want to choose AIRWAY entry and exit waypoints that permit an orderly and
efficient flight path, blending smoothly with your SID and STAR.

48
To select an airway, if the last waypoint of your departure procedure is known to be on an airway,
and you’ve entered its altitude, then you simply go into the ADD ROUTE WPT page and
immediately go to the AIRWAY page. If it is not, then select a suitable waypoint on the airway in
question and enter it first. In either case, you will definitely want to enter the altitude value before
selecting . If you’ve been following good flight planning practices, you will have already reviewed
all of the altitudes for your departure prior to adding ROUTE waypoints. The key here is that when
you add airway waypoints, the FMS will assign the altitude of the entry waypoint to all of the
waypoints added from the airway. These can be edited after the fact, of course.

Given that you’ve got your entry waypoint ready, when you go into the AIRWAY page, you will be
presented with a list of airways that the waypoint appears on, along with the next waypoint in the
sequence. You will likely see each airway listed twice, once for each direction of travel. If you
refer to your charts, you will know what the next waypoint after your entry should be, making
selection simple. If you need to, though, you can check each option to search for your exit
waypoint instead. Once you’ve advanced the row selector to the desired exit waypoint, pressing
the SELECTOR KNOB, or pressing ENTER in DKE mode, will automatically add all of the
waypoints from the airway into your ROUTE waypoint list.

As with many aspects of flight planning, we have to exercise a bit of care here. The X-Plane
navigation database permits as many as a 100 waypoints in a flight plan. This is actually 99
entered via the FMS plus the initialization waypoint - the latitude and longitude of where the
airplane is parked when you first launch the simulation and when you press the INIT key. Airways
can have well over 100 waypoints in some instances. So it is important to keep track of how many
waypoints you are adding to your SID, ROUTE and STAR waypoint lists. If you try to load a plan
that would result in more than 100 total waypoints, the FMS will present a visual warning, and the
load will not be successful.

That said, it is possible to link AIRWAY with AIRWAY, since it is possible that your exit waypoint
might coincide with a waypoint that happens to be on more than one airway. This makes it
exceptionally convenient to link a complete route from your departure airport to your destination,
using nothing but procedures and airways. It is also the fastest way to exceed the 100 point
waypoint limit.

49
50
4.9 LIMITATIONS
The ADD RTE WPT and EDIT WAYPOINT pages have a few limitations and one caveat:

● If you've entered any data at all, the page data text will turn from green to yellow. This means
that if you attempt to return to the MCDU INDEX, or go BACK to whichever edit selection
page you were on, you will be warned that you have unsaved data. A second attempt to
leave the ADD ROUTE WAYPOINT or EDIT WAYPOINT pages will be successful, and you
will lose the data you entered.

● If you've entered and saved a waypoint in the ADD ROUTE WAYPOINT page, and it is the
only waypoint entered, you will be warned that a ROUTE REQUIRES TWO WAYPOINTS
when you try to exit to the MCDU INDEX. A second attempt to leave will be successful, and
you will lose the single waypoint entered, with total ROUTE entries being returned to zero.

● If at any time you have unsaved data, or less than two waypoints, and you select the RADIO
button (the button closest the selector knob in the second row of buttons), you will lose any
unsaved data. Additionally, you will lose your waypoint entry if there is only one. There is no
warning of any kind since it is presumed that any need to use the RADIO shortcut button
would be for an urgent communications need.

4.10 EDITING: ADDING WAYPOINTS

When you first navigate to the ADD RTE WPTS page, the default navigation waypoint type of fix is
automatically selected for you. This selection persists, along with the last altitude entered, for any
subsequent waypoint entry. Once selected, the entry type is presented at the top left of the page,
below the waypoint number.

4.11 EDITING: AIRP, VOR, NDB & FIX

Use the SCRATCHPAD to enter the navigation identifier of your selected waypoint type. Use
button L3 to inject this data. If you picked a valid identifier, it will be accepted. If not, you will be
advised that the NAV ID cannot be found.

51
4.12 EDITING: LAT/LON
Use the scratchpad to enter numeric data for latitude and longitude. You can have up to six digits
in your mantissa -- the decimal portion of the entry. For SOUTH and WEST, you must either enter
the MINUS sign using the digital keypad, or you can use the +/- key after entering numeric data
only on the scratch pad. Use buttons R1 and R2 to inject this data as needed.

4.13 EDITING: ALL TYPES

If you try to enter an airport, VOR, NDB or FIX when LAT/LON is the current waypoint type, it will
be rejected. Similarly, if you attempt to enter a LAT or a LON for a non-LAT/LON waypoint, it will
also be rejected.

Enter your altitude using the scratchpad and button L5 to inject it. This is a good thing to do for
every waypoint, although it is not required.

Use button R5 to SAVE your waypoint, and advance to the next.

Keep at it until you're done. If you have a long flight plan, you would find an online planner
exceptionally easier. This is one I've used and rather like: ​ ​[Link]

4.14 ADDING VS. EDITING

There are two main differences between adding and editing.

The first is that when you select a waypoint and navigate to the editor using a click on the center of
the selector knob, the full data for the waypoint is automatically populated. The second is that you
no longer "SAVE" a new waypoint, you "UPDATE" the existing waypoint.

In addition to UPDATE, you can also DELETE, INSERT BEFORE or INSERT AFTER. This gives
you a great deal of flexibility in modifying whatever list of waypoints that needs revision. What
these functions do is self explanatory.

Otherwise, editing a waypoint is exactly like entering a new one. If you don't wish to use the
waypoint type that was originally selected, you use the second row of buttons on the MCDU to

52
 choose a new one, and that changes the entry restrictions appropriately when it comes to
navigation identifier or latitude and longitude.

If you've decided not to edit a waypoint, you can go BACK to the original edit list of waypoints
without updating, deleting or inserting. If you've entered data, you will be warned, naturally, but
again, repeating the BACK selection will override the warning.

5.0 IN FLIGHT FMS USAGE

Prior to version 2.0 of the X-Crafts E175, using the Tekton FMS in was relatively pre-flight
focussed. Once you entered you complete flight plan, there was little else to do in the FMS except
to watch the STATUS page, or perhaps to use the AUTOPILOT page to more easily enter your
heading, altitude, speed and vertical velocity. With the addition of PERF and PROGRESS pages,
the FMS became more integral to your complete flight. This section hits on the highlights of how
the FMS can be used, and how to fly the aircraft so that you are using the same techniques that
were used to create the E195’s internal fuel usage tables.

5.1 PREFLIGHT
Data to have available before you even enter the cockpit consists of the departure and approach
charts with radio frequencies, airways charts, your passenger load data (payload weight) and
your weight and balance estimation.

When you fire up the GPU or APU, and turn on the batteries, the FMS becomes available. The
first page is always going to be the RADIO page, so enter the first set of frequencies you need to
use in both the COMM and NAV slots, as well as the ADF if your flight plan calls for it.

When you’re ready to enter the flight plan, proceed to the MCUD INDEX page and press INIT.
Then fully enter your flight plan using the techniques and information described in previous
sections.

Remember: DO NOT press EXEC after the flight plan waypoints have been entered. You’re not
done flight planning just yet.

53
After the SID, ROUTE and STAR have been entered, go into the PERF 1 page and adjust your
payload and fuel values. Select your favored units of measure as needed. Enter your
CG/MAC% values for weight and balance. Select FLAPS 2 using button R1. You can select
other options if you wish, but FLAPS 2 has been used for all fuel table generation, just like it was
done during actual E195 flight testing. Given all of this data, you can now set your trim correctly,
matching the setting of the trim to the table value that’s provided. Make a mental note of your
V-speeds. These will be called out as you take off.

With PERF 1 attended to, go into PERF 2 and enter your cruise airspeed or Mach number, as
required by your average cruise altitude, and then your initial and final cruise altitudes needed to
determine TOC/TOD. This will give you a fuel calculation. Enter your winds aloft and cruise
altitude OAT if you have this data available. This will alter your fuel calculation as needed.
Review the fuel quantity and ensure that you have sufficient fuel by returning to PERF 1. If you
do, no further action is necessary in PERFORMANCE. However, economy minded airlines will
actually reduce the fuel load by offloading at the departure airport to avoid just ferrying fuel
around the country. You can go back and forth between PERF 1 and PERF 2 to see the effects
of less fuel on your trip. It might not be a big difference, but fuel management keeps flight costs
down. Fuel economy calculations are provided by more advanced FMS computers to drive the
cost efficiency of their operations. In the E195 FMS, you can still see the effect, and perhaps
become a better virtual airline pilot by using this sort of planning procedure.

After you are satisfied with all of your PERFORMANCE entries, you can now go back to the
MCDU INDEX and press EXEC. After you press EXEC, you cannot change your PERF 2
entries.

5.2 TAXI AND TAKEOFF

You can change back to the RADIO page by pressing the RADIO button on the MCDU. While
going through the rest of your preflight startup checklists, you may have to change radio
frequencies, and this is a good place to accomplish that.

When you finally get the aircraft all the way to the end of the runway, and you’re ready to go, as
you taxi onto the runway, press the T/O switch just ahead of the throttles. You will get an audible
takeoff check from the FMS. If your brakes, flaps, trim and speed brakes are properly configured,
the FMS will announce “TAKEOFF OKAY.” If you’ve missed something, you will be warned. For

54
example, if you forgot to set your flaps, which should be set to the same selection you made in
PERF 1, you will hear “NO TAKEOFF: FLAPS.” Similar warnings are provided for the other
three items that are checked.

At this time you can also change the FMS page to PROGRESS. In PROGRESS you will now
monitor your waypoints as you pass them. You also have an estimate of TOC and TOD, which
are intended to be within approximately 2 miles of the ideal traveled distance.

5.3 CLIMB
TOC is correctly reached by flying the aircraft in a standard profile, starting at takeoff, which
consists of the following:

● Full throttle takeoff to rotation and positive vertical speed. Flap setting 2, aircraft trimmed to
PERF 1 value.
● After takeoff, landing gear is retracted and flaps reduced one notch at or before 500 feet.
● Engine RPM is reduced to 88% N1.
● FLCH is engaged, with 250 KIAS speed requested and the INITIAL CRZ ALT set as the
altitude request.
● Fully retract flaps at 3000' AGL.
● Passing 10,000 feet, the AP airspeed request is increased to 270 KIAS.
● Passing FL300, the AP is toggled into Mach airspeed mode, and .74 Mach is entered as the
airspeed request.
● At reaching actual TOC, the FLCH mode will deactivate. Monitor AP to ensure that
AUTOTHROTTLE is engaged. Manually engage as necessary.
● Adjust the AP airspeed request to the pre-planned cruise airspeed.

TOC is continuously adjusted during climb if the departure procedure or ATC clearances
mandate level flight for a portion of the departure. This functionality is effective, however it can
induce error in the calculated value of TOC due to the fact that one may or may not terminate or
initiate climb portions of the departure in an aggressive manner. That said, TOC is really only an
efficiency guide, not a make or break altitude goal. Realizing that many factors can alter the
degree of efficiency of a given flight, it is wise to allow additional fuel for variation from ideal
performance parameters.

55
5.4 CRUISE
After reaching cruise, the use of the FMS is purely as a flight following utility, monitoring the time
and fuel estimates on the PROGRESS page. Actual winds aloft are used to adjust waypoint
calculations, as are variations in fuel flow. These values can jump around quite a bit as a result,
since they are re-calculated frequently.

Some time before TOD is reached, ATC will provide your terminal clearance procedures. This
may very likely result in a different runway and/or procedure selection. If this occurs, simply go to
the DEPARTURE page and make the necessary revisions. Afterwards, go into the STAR EDIT
page and review any non-constrained altitudes. Finally, return to the MCDU page and press the
EXEC key. The revision will be loaded and you can continue your flight normally.

5.5 DESCENT
The value of TOD provided is for the most fuel efficient descent. This profile is flown as follows:

● Final waypoint altitude, which is normally the first waypoint of a STAR, is entered as the
altitude request on the AUTOPILOT page.
● Upon reaching TOD, the throttle is fully retarded.
● FLCH is selected. Above FL300, select Mach .74 as the AP speed request.
● Passing FL300, toggle the AP from Mach to KIAS mode. Enter 270 KIAS for the AP speed
request.
● Passing 10,000 feet, enter 250 KIAS for the AP speed request.
● At or before reaching the last waypoint of the ROUTE, go to PERF 1 and add the empty
aircraft weight to the payload and fuel weights. This will give you your actual aircraft weight at
this point of the flight. Then go to PERF 3 and override the PRED LANDING WGT. Select
ICING conditions as needed. Review the values for various V-speeds on this page.
● Upon reaching the end of the ROUTE, resume either normal VNAV or manual altitude
management as desired and manage airspeed as appropriate for the altitude and phase of
the approach, subject to ATC clearance.

It’s fair to say that this standard descent profile is the most efficient because it keeps the
aircraft at altitude the longest. However, it is also a rather aggressive descent. If a shallower

56
 descent is desired than is provided by the FMS, allow for the extra fuel such a descent will
require, since you will be descending earlier than is optimal for maximum fuel efficiency.

5.6 LANDING, MISSED APPROACH AND POST FLIGHT

Once you’ve begun your terminal procedure, the FMS is only useful on the PROGRESS page,
again to monitor your progress through the waypoints. The destination airport remains fixed as
line 3 until you are near the end of your last leg on final approach. If you’ve entered a specified
approach, many times there will be a set of missed approach waypoints or a hold waypoint. If a
hold, it must be either hand flown, or flown using the heading mode and altitude mode autopilot
controls. Be aware that the fuel calculations provide for a one hour hold time at this hold fix, at a
worst case altitude of 3000’ above the destination runway altitude, flying at 200 KIAS. This can
be a rather large amount to be sure, since slow speeds and low altitudes are where a jet aircraft
will use the most fuel. To mitigate this effect, it is better to fly faster and higher if ATC clearance
can be obtained.

After you’ve successfully landed and parked, if you’re flying a subsequent flight, the FMS can be
fully reset in order to prepare a completely new flight plan. Go to the MCDU INDEX and press
CLR. You will be asked to confirm. Press CLR a second time within 5 seconds and all airport,
departure, arrival and route data will be completely cleared. You will then be returned to the
RADIO page to begin fresh when the aircraft is started again.

6.0 KNOWN LIMITATIONS, HELPFUL TIPS AND ADVICE

6.1 KNOWN LIMITATIONS

Due to limitations in the functionality offered through the X-Plane SDK and the autopilot, it is not
possible to implement procedures that involve flying VOR/DME arcs, procedure turns, and
essentially the types of flight paths that are defined by radio navigation aids, as opposed to fixed
position waypoints. When a procedure leg type is discovered for a particular airport that the
stock autopilot cannot fly, and the stock NAV display cannot draw completely, the FMS will draw
those legs of the procedure that it can. The undrawn legs will be represented by a direct link
from the last usable waypoint to the next. At these positions the user will detect a distinct
difference between what is ultimately displayed, and whatever documents they have that they are
referring to when planning their flight. When planning and choosing your SID and/or STAR

57
 procedures, and you wish to employ one that uses one of the more complex navaid related
procedures, you will have the opportunity to pre-plan alternate waypoints and to enter them via
the editor. Remember, you have final say over the waypoints that you fly, and the Waypoint
Editor can help you fly the actual route that you wish or need to fly.

Also, there are some procedure waypoint lists that will end up showing only the endpoint, or
perhaps nothing at all. For example, one of the SIDs out of KSFO on runway 01L has three
procedural elements, but none of them present a waypoint the FMS can load or display. The
result is that the only waypoint loaded for the SID is the runway threshold. This gets more
interesting in that there’s no SID TRANSITION to connect this SID with the ROUTE. So, when
this occurs, the user should consult their charts and either modify their ROUTE or the SID to add
appropriate waypoints to accommodate the situation.

6.2 TIPS and ADVICE

1. Before you load a plan into the X-Plane navigation database using EXEC, always click on
INIT first. This completely clears the database, wiping the slate clean so that you won’t have
any unexpected results.
2. If you must edit your FLT PLAN waypoints enroute, it is best to do so while you are in the
heading and altitude mode of the autopilot. Updates of waypoints are nominally not a
problem, but waypoint deletion commands an automatic INIT of the database. In this case,
you will need to advance your waypoint selection in the FLT PLAN page to the next
destination waypoint and select DIRECT TO. If you don’t do this, since the X-Plane autopilot
will consider the first waypoint of a freshly loaded flight plan to be your destination. Once you
return to using the FMS to guide your flight, the autopilot will likely turn the aircraft around and
start heading back the way you came, or other unexpected behavior.
3. When first getting used to procedures, it is often easier to keep your selections simple. For
example, as in the demo, you are only required to fly a STAR transition plus a STAR at the
end of the flight, leaving the choice of approach to you, as long as you get ATC clearance!
4. Use downloaded flight routes with caution. These will often go from airport to airport. You
can’t use these with SIDs and STARs because then you would be duplicating the airport
waypoint. While these routes can be loaded and then the termination waypoints edited, and
deleted if need be, that’s a good deal of work. Fortunately, if you do make these sorts of
edits, you can re-save the new version of the plan using the SAVE page of the MCDU.

58
 5. Whenever this FMS loads waypoints from files, a “sanity check” is performed to validate the
placement. As it’s loaded, each waypoint has to be “found” in the various X-Plane navigation
data files. If, for some reason, it finds the wrong one, or cannot find anything, then the
waypoint requested by the procedures file, or the flight plan .fms file, is converted to a GPS
waypoint, retaining the original navigation ID. In other words, a listing of VOR - PHX might
become GPS - PHX.
6. You can research your SIDs and STARs online at​ ​[Link] Users outside the
United States may wish to visit ​[Link] instead.

6.3 WHY IS A SID/STAR NOT AVAILABLE?

This is going to be a frequent question, perhaps!

You’ve done your flight planning to the best of your ability, you have everything laid out, you know
where you’re going and how you’re going to program your flight data into the MCDU. And
suddenly, you discover...where’s my SID (or STAR)? Well, it may not be in the database at all.

The original GNS430 data that was released with X-Plane version 10.30 in September of 2014
was a great start. This has been updated in subsequent releases. However, this is often not the
most current and up to date data since Navigraph and Aerosoft release new AIRAC cycles more
often than the development staff at Laminar Research provide updates to X-Plane. There can be
omissions in the data, depending on the locale, and the only way to be certain that you have the
most recent version is to either make a one time purchase of new data, or you can subscribe to a
service that provides periodic updates. This is commonly referred to as the aforementioned
AIRAC cycle, and the release that you are using is detailed in the [Link] whenever you run the
E195 in X-Plane. The downloaded data goes into your /X-Plane/Custom Data folder, and this
folder is not updated by Laminar Research. It is the user’s responsibility. Visit either
[Link] or ​[Link] for more details.

7.0 FMS TUTORIAL VIDEOS

​ -Crafts Youtube Channel​.
There is a set of tutorial videos explaining how to use the FMS on the X
Watch them to easily learn how to use the custom FMS! While the videos cover the E175 aircraft,
the use of the FMS is exactly the same. All videos​ ​HERE

59