Twin-Sphere Screwed Type Flexible Rubber Joint

TWINFLEX Screwed Type

Excellent performance for vibration absorption, displacement
absorption, and high-pressure resistance.

Feature Applications
High Efficiency for Vibration and Noise Isolation This product is mainly applicable for piping systems in commercial and
The twin sphere makes the spring constant small, decreases the body industrial buildings and plants.
natural frequency and increases the efficiency of vibration absorption. Applicable fluids are exclusively water including cold water, warm water,
cooled water, sea water, etc.
Withstandability This product can not be used for drinking water, pool water, oil, or boiled water.
It can withstand a bursting pressure of over 5.0MPa and a maximum working
pressure of 1.6MPa and with the combination of excellent formative
technique and strong chemical fibre. Structure
Large Displacement Absorption for Eccentricity,
Axial Movement and Angular Movement
Since it can absorb large displacement, TWINFLEX screwed type flexible rubber joint
is most appropriate for the protection of pipe line system. For example, it can prevent
the destruction of connecting pipe due to earthquake and subsidence of ground.
1525
Applicable for both Suction and Delivery
The joint fits for both suction and delivery. φ
NPT or
BS21
Highly Reliable
The packing parts are strengthened with steel reinforcing rings to prevent the
rubber body from slipping out of the fitting sides of flanges.
φ

Convenient to install
When limited space is allowed for installation, the free type sockets can be
screwed separately to pipe before fitting in the joint.

D
PC
Durability

φ
Reciprocating pressure test for 20,000 cycles or above. No. Parts Material No. Parts Material
Flange-A Ductile Iron Inner Rubber Synthetic Rubber
Operating Conditions and Performance Flange-B Ductile Iron Outer Rubber Synthetic Rubber
Temp.[ C] 80
70 Nut Mild Steel Reinforcing Cord Synthetic Fiber
60

40
Bolt Mild Steel Union Edge Ductile Iron
20
Reinforcing Cord Synthetic Fiber Washer Mild Steel
0 The material of No.1, 2 & 9 can be changed to SUS304 and SUS316.
10
20
The product is also applicable for oil use by changing the rubber material.
0 0.5 0.9 1.0 1.5 1.6 Pressure MPa
0.086
650mmHg
0 5.1 9.2 10.2 15.3 16.3 Kgfcm 2 If need be, please contact us.

Dimensions and Allowable Movements

Nominal Dia. Dimension [mm] Mass Union Edge [mm] Flange [mm] Allowable Movement [mm] Installation Tolerances [mm]
mm inch L φd ℓ [Kg] Rc H φD PCD φh φOD T.M. A.E. A.C. A.M. T.M. A.E. A.C. A.M.
15 1/2 120 25 30 1.7 1/2 41 68 70 11.0 93 15 10 15 15 6 3 6 7.5
20 3/4 120 25 30 1.8 3/4 41 68 70 11.0 93 15 10 15 15 6 3 6 7.5
25 1 120 25 30 1.9 1 41 68 70 11.0 93 15 10 15 15 6 3 6 7.5
32 1 1/4 175 35 35 3.1 11/4 50 90 95 13.5 121 20 10 20 20 8 3 6 7.5
40 1 1/2 175 35 35 3.3 11/2 56 90 95 13.5 121 20 10 20 20 8 3 6 7.5
50 2 175 45 40 5.4 2 69 106 110 13.5 135 20 10 20 20 8 3 6 7.5
A.C.: AxialCompression, A.E.: Axial Elongation, Please note that the information in the above table is for single movement only.
A.M.: Angular Movement, T.M.: Transverse Movement In case of complex movements, please do adjustment by using the following formula.
T.M. A.M.
Axial
compression
Axial
elongation
angular
movement
transverse
movement
C.A.E. (C.A.C.) = A.A.E.(A.A.C.) {1 ( A.T.M + A.A.M )}
C.A.E. (C.A.C.): Correct Elongation Movement (Correct Compression Movement)
A.A.E. (A.A.C.): Allowable Elongation Movement (Allowable Compression Movement)
A.T.M.: Allowable Transverse Movement A.A.M.: Allowable Angular Movement
Example: In case of 50mm joint, if 10mm transverse movement is needed, then the
Tolerances for installation are included in the allowable movements correct elongation should be: C.A.E = 10 {1 ()}10 20= +
5mm 0
20
(Allowable movements = Tolerances for installation + Operating movements). There is reaction force from rubber joints due to the load of the internal pressure, so during the installation, please use the metal fittings to
fix the pipe tightly to ensure the joints work efficiently. In case the pipe cannot be fixed tightly, please use the control unit for the joints.

Connection Procedure

main body

socket Screwing
flange A

Remove the bolt and disassemble flange Put flange A through the counterpart Screw the socket to the counterpart Use bolts to connect flange A and B.
A and socket from the main body. pipe. pipe.
Note The content of this catalog is subject to change without prior notice.
AGENT
8-4, Asahi, Yoshikawa
Saitama 342-0008 Japan
WE2-1502