0% found this document useful (0 votes)

80 views120 pages

Brunei Darussalam: I. Countries With Mandatory Standards For Government Procurement Only

The document outlines the mandatory standards for government procurement in Brunei Darussalam and Cambodia, detailing the rationale for regulation, regulatory bodies, legislative frameworks, and specific mandatory standards for various electrical products. Brunei's regulations focus on safety and reliability in electricity supply, while Cambodia emphasizes consumer protection. Both countries have established conformity assessment regimes to ensure compliance with international standards.

Uploaded by

chuminhduc15052018

We take content rights seriously. If you suspect this is your content, claim it here.

Available Formats

Download as PDF, TXT or read online on Scribd

0% found this document useful (0 votes)

80 views120 pages

Brunei Darussalam: I. Countries With Mandatory Standards For Government Procurement Only

Uploaded by

chuminhduc15052018

We take content rights seriously. If you suspect this is your content, claim it here.

Available Formats

Download as PDF, TXT or read online on Scribd

VERSION 12 – as of May 2010

I. COUNTRIES WITH MANDATORY STANDARDS FOR GOVERNMENT PROCUREMENT ONLY

BRUNEI DARUSSALAM

I. RATIONALE FOR REGULATION

COUNTRY RATIONALE FOR REGULATION

Brunei Ensure safety and reliability in the supply of electricity

Darussalam

II. REGULATION BODY

COUNTRY REGULATORY BODY

Brunei Department of Electrical Services

Darussalam Prime Minister Office

III. LEGISLATIVE FRAMEWORK

COUNTRY LEGISLATIVE FRAMEWORK

Brunei Electricity Act (1984)

Darussalam
VERSION 12 – as of May 2010

IV. MANDATORY STANDARDS

Country Total Product Type or STANDARDS

Product grouping Domestic Please tick Relevant Extent of State
Standards box if International Alignment Reason if
mandatory Standards MOD.
Brunei 1 Adaptor – for electronic, IEC 60742
Darussalam electrical, computer and IEC 61558-2-6
telephonic appliances IEC 60065
IEC 60950
2 Air Cooler IEC 60335-2-98
3 Audio Product IEC 60065
4 Coffee Maker, slow cooker, IEC60335-2-15
steam boat and similar
appliances
5 Cooking Range IEC 60335-2-6
6 Decorative Light fixture IEC 60598-2-20
7 Hairdryer IEC 60335-2-23
8 High-Fidelity Set IEC 60065
9 Home Computer System IEC 60950
(inclusive of monitor,
printer, speaker and other
mains operated
accessories)
10 Immersion water heater IEC 60335-2-74
11 Iron IEC 60335-2-3
12 Kettle IEC 60335-2-15
13 Laser Disc Set IEC 60065
14 Microwave Oven IEC 60335-2-25
15 Mixer, blender, mincer and IEC 60335-2-14
similar appliances
16 Mobile Split Air-conditioner IEC 60335-2-40
17 Refrigerator IEC 60335-2-24
18 Rice Cooker IEC 60335-2-15
19 Room air-conditioner IEC 60335-2-40
20 Table lamp or standing IEC 60598-2-4
lamp
21 Table or standing fan IEC 60335-2-80
22 Television or video display IEC 60065
unit
23 Toaster, grill, roaster, hot
plate, deep fryer, wok and
VERSION 12 – as of May 2010

Country Total Product Type or STANDARDS

Product grouping Domestic Please tick Relevant Extent of State
Standards box if International Alignment Reason if
mandatory Standards MOD.
similar appliances

- for hot plate and similar IEC 60335-2-6

appliances
- for toaster, grill, oven and IEC 60335-2-9
similar appliances
- for deep fryer, electric IEC 60335-2-13
wok and similar appliances
24 Vacuum Cleaner IEC 60335-2-2
25 Video Cassette Recorder IEC 60065
26 Wall fan IEC 60335-2-7
Ceiling fan
27 Washing Machine IEC 60335-2-7
28 Ballast for tubular IEC 61347-2-3
fluorescent lamp IEC 61347-2-2
29 Isolating transformer for IEC 61558-2-6
downlight fitting IEC 61347-2-2
30 3-pin rectangular type 13- SS 145:PT.1
amp plug
31 Fuse (less than or equal to SS 167
13-amp) for use in plug
32 3-pin round type 15-amp SS 472
plug
33 Multi-way Adaptor SS 246
34 3-pin portable socket-outlet SS 145:PT.2
SS 358:PT.5
35 3-pin 13 amp socket-outlet SS 145 :PT.2

36 3-pin round type 15-amp SS 472

socket-outlet
37 Domestic electric wall IEC 60669-1/SS227:PT.1
switch
38 Fuses / Fuse Links to 63A IEC 60269-1
39 Switches for general IEC 60669-1
purposes
40 Plugs and socket-outlets IEC 60884-1
for household and similar IEC 60884-2-1
purposes IEC 60884-2-3
41 Low-voltage distribution link IEC 60269-1
VERSION 12 – as of May 2010

Country Total Product Type or STANDARDS

Product grouping Domestic Please tick Relevant Extent of State
Standards box if International Alignment Reason if
mandatory Standards MOD.
fuses
42 Miniature Circuit Breaker IEC 60898
43 Electronic Switch IEC 60669-2-1
44 Electromagnetic Remote IEC 60669-2-2
Control Switch
45 Residual Current Circuit IEC 61008-1
Breakers without integral IEC 61008-1-1
Overcurrent Protection IEC 61008-2-1

46 Residual Current Operated IEC 61009-1

Circuit-Breakers with IEC 61009-2-1
Integral Overcurrent IEC 61009-2-2
Protection for household
and similar uses (RCBOs)

V. MODE OF REGULATION AND TYPES OF CONFORMITY ASSESSMENT REGIMES

COUNTRY TYPES OF CON- MODE OF REGULATION

FORMITY ASSESS-
MENT REGIMES

Brunei Registration Suppliers registering products should register through the Product Procurement Section. Registration
Darussalam Committee shall strictly review and analyse input information prior to endorsing approval of product
registration based upon the mentioned requirements :-

¾ Corporate information
¾ Quality and Performance – (Quality Assurance details, test reports & certification carried out
by International Test Bodies and representation of International Standards used).
¾ Reliability and safety
¾ Maintenance management
¾ Track record
¾ Stock and delivery schedules
¾ After sale service
¾ Technical Presentation
VERSION 12 – as of May 2010

VI. FLOWCHART OF MEMBER COUNTRIES’ REGIME

VERSION 12 – as of May 2010

VII. MAINS VOLTAGE, FREQUENCY AND MAINS PLUG CONFIGURATION

Country Mains Mains Applicable Mains Plug Configuration

Voltage Frequency Legislation Domestic Please tick Relevant Extent of Diagram of Mains Plug Configuration-
and and Standard box if International Alignment
Tolerance Tolerance mandatory Standard -
Brunei 240V single 13A SSO
50Hz ± 1%
Darussalam phase with 3 pin rectangular
a tolerance plug top.
of ± 5%
15A SSO
3 pin round plug
top.
415V three 50Hz ±1%
phase with
a tolerance
of ±5%

VIII. CONTACT PERSON

Country Contact Person and Address

Brunei Darussalam Haji Ismail Puteh, Muhammad Amir Sharifuddin Haji Ali, Salleh Hj Kahan,
Senior Executive Engineer, Engineer, Special Duties officer,
Department of Electrical Department of Electrical Services, Construction Planning & Research Unit,
Services, Prime Minister Office, Ministry of Development,
Prime Minister Office, Old Airport, Berakas BB 3510 Old Airport, Berakas BB 3510
Old Airport, Berakas BB 3510 Brunei Darussalam.
Brunei Darussalam. Contact No. (673)2 381543
Contact No. (673) 2 331736 Fax No. (673) 2 381541
Contact No : (673) 2 383061 Fax No. (673) 2 380994 Email : [Link]@[Link]
Fax No: (673) 2 383768 Email : mdasharifuddin@[Link]
Email :
des@[Link]
ismail_puteh@[Link]
VERSION 12 – as of May 2010

II. COUNTRIES WITH MANDATORY STANDARDS

CAMBODIA

I. RATIONALE FOR REGULATION

COUNTRY RATIONALE FOR REGULATION

Cambodia Consumer Protection

II. REGULATION BODY

COUNTRY REGULATORY BODY

Cambodia Ministry of Industry Mines and Energy (Department of Industrial Standards of Cambodia – ISC) :
drafting and issuing of regulations and registering of regulated products

Ministry of Commerce (Cambodia Import Export Inspection and Fraud Repression Department –
Camcontrol)

III. LEGISLATIVE FRAMEWORK

COUNTRY LEGISLATIVE FRAMEWORK

Cambodia Law on the management of quality and safety of product and services (2000)
VERSION 12 – as of May 2010

Sub-decree No.42 on Industrial Standards of Cambodia (2001)

Ministerial Regulations for Product and Safety Standards :

- Ministerial Regulations No 115 dated 12 February 2004 on Industrial Standards of Cambodia
for Electrical and Electronic Products as Mandatory Standards,
- Ministerial Regulations No. 1003 dated 13 September 2006 on The Determination of types of
electrical and electronic products to be complied with Cambodian industrial standards as
mandatory standards.
- Ministerial Regulations No 1302 dated 25 December 2006 on establishment of Cambodian
standards for electric and electronic as mandatory.

IV. MANDATORY STANDARDS

Country Total Product type or STANDARDS

Product grouping Domestic Please tick box Relevant International Extent of Alignment State reason if MOD
Standards if mandatory Standards
1- Electric Fans CS 0045:2003 3 IEC 60335-2-80 IDT
Cambodia 39 CS 0040:2003 3 IEC 60879 IDT
CS 0010:2003 3 IEC 60335-1 IDT
2- Refrigerators, CS 0010:2003 3 IEC 60335-1 IDT
Freezers and other CS 0021:2003 3 IEC 60335-2-24 IDT
refrigerating or
freezing equipment
3- Electric washing CS 0010:2003 3 IEC 60335-1 IDT
machine CS 0019:2003 3 IEC 60335-2-7 IDT
CS 0020:2003 3 IEC 60335-2-4 IDT
4- Electric sewing CS 0010:2003 3 IEC 60335-1 IDT
machine CS 0022:2003 3 IEC 60335-2-28 IDT
5- Electric Drill CS 0042:2003 3 IEC 60745-1 IDT
CS 0043:2003 3 IEC 60745-2-1 IDT
VERSION 12 – as of May 2010

Country Total Product type or STANDARDS

Product grouping Domestic Please tick box Relevant International Extent of Alignment State reason if MOD
Standards if mandatory Standards
6- Electric grinders ( CS 0042:2003 3 IEC 60745-1 IDT
up to 100 mm ) CS 0048:2003 3 IEC 60745-2-3 IDT
7- Electric Circular CS 0042:2003 3 IEC 60745-1 IDT
Saws and Circular CS 0028:2003 3 IEC 60745-2-5 IDT
Knives
8- Home computer CS 0047:2003 3 IEC 60950 or IDT
system(inclusive of IEC 60950-1 IDT
monitor, printer,
speaker, and other
mains operated
accessories
9- Adaptor CS 0044:2003 3 IEC 60742 IDT
CS 0046:2003 3 IEC 61558-2-6 IDT
CS 0029:2003 3 IEC 60065 IDT
CS 0047:2003 3 IEC 60950 or IDT
IEC 60950-1 IDT
10- Vacuum Cleaners CS 0010:2003 3 IEC 60335-1 IDT
CS 0018:2003 3 IEC 60335-2-2 IDT
11- Food CS 0010:2003 3 IEC 60335-1 IDT
mixers/blenders CS 0015:2003 3 IEC 60335-2-14 IDT
12- Electrical CS 0010:2003 3 IEC 60335-1 IDT
Shavers CS 0033:2003 3 IEC 60335-2-8 IDT
13- Electric soldering CS 0010:2003 3 IEC 60335-1 IDT
Irons CS 0023:2003 3 IEC 60335-2-45 IDT
14- Electric CS 0010:2003 3 IEC 60335-1 IDT
instantaneous or CS 0049:2003 3 IEC 60335-2-21 IDT
storage water heater
and immersion
15- Electrical Hair CS 0010:2003 3 IEC 60335-1 IDT
Dryers CS 0011:2003 3 IEC 60335-2-23 IDT
16- Electrical Iron CS 0010:2003 3 IEC 60335-1 IDT
CS 0014:2003 3 IEC 60335-2-3 IDT
17- Electric Kettles CS 0010:2003 3 IEC 60335-1 IDT
CS 0012:2003 3 IEC 60335-2-15 IDT
VERSION 12 – as of May 2010

Country Total Product type or STANDARDS

Product grouping Domestic Please tick box Relevant International Extent of Alignment State reason if MOD
Standards if mandatory Standards
18 - Electric CS 0010:2003 3 IEC 60335-1 IDT
Microwave Ovens CS 0016:2003 3 IEC 60335-2-25 IDT
19- Electrical Deep CS 0010:2003 3 IEC 60335-1 IDT
Fryers CS 0013:2003 3 IEC 60335-2-13 IDT
20- Electrical Multi- CS 0010:2003 3 IEC 60335-1 IDT
Purpose Cookers CS 0012:2003 3 IEC 60335-2-15 IDT
CS 0013:2003 3 IEC 60335-2-13 IDT
CS 0037:2003 3 IEC 60335-2-9 IDT
21- Electrical ovens, CS 0010:2003 3 IEC 60335-1 IDT
cookers, cooking CS 0037:2003 3 IEC 60335-2-9 IDT
plates, boiling rings,
grillers and roasters
22- Electrical Fixed CS 0010:2003 3 IEC 60335-1, IDT
Immersion Heaters CS 0038:2003 3 IEC 60335-2-73 IDT
23- Portable CS 0010:2003 3 IEC 60335-1 IDT
Immersion Heaters CS 0039:2003 3 IEC 60335-2-74 IDT
24- HI-FI SETS CS 0029:2003 3 IEC 60065 IDT
25- Television CS 0029:2003 3 IEC 60065 IDT
26- General purpose CS 0026:2003 3 IEC 60669-1 IDT
switches
27- Miniature Circuit CS 0032:2003 3 IEC 60898-1 IDT
Breaker
28- Plug and socket- CS0017:2003 3 IEC 60884-1 IDT
outlet for household
and similar purpose
29- 13A 3pin plugs CS 0052-1:2006 3 BS 1363-1:1995 IDT
and fused plugs
30- 13A 3pin fixed CS 0052-2:2006 3 BS 1363-2:1995 IDT
and portable socklet-
outlets
31- Multi-way CS 0052-3:2006 3 BS 1363-3:1995 IDT
adaptors
32- PVC insulated CS 0024:2003 3 IEC 60227-1 IDT
copper cable
VERSION 12 – as of May 2010

Country Total Product type or STANDARDS

Product grouping Domestic Please tick box Relevant International Extent of Alignment State reason if MOD
Standards if mandatory Standards
33- Electric table, CS 0034:2003 3 IEC 60598-1 IDT
desk, bedside or CS 0035:2003 3 IEC 60598-2-4 IDT
floor-standing lamps
34- Electrical Hand CS 0034:2003 3 IEC 60598-1 IDT
Lamps CS 0036:2003 3 IEC 60598-2-8 IDT
35- Self ballast lamp CS 0027:2003 3 IEC 60968 IDT
for general lighting
service
36- Starterholder , CS 0031:2003 3 IEC 60400 IDT
lampholder for
tubular fluorescent
lamps
37- Fluorescent CS 0008:2003 3 IEC 60081 IDT
lamps
38- Lighting Chains CS 0034:2003 3 IEC 60598-1 IDT
CS 0041:2003 3 IEC 60598-2-20 IDT
39- Incandescent CS 0006:2003 3 IEC 60064 IDT
lamps CS 0025:2003 3 IEC 60432-1 IDT

V. MODE OF REGULATION AND TYPES OF CONFORMITY ASSESSMENT REGIMES

COUNTRY TYPES OF CON- MODE OF REGULATION

FORMITY ASSESS-
MENT REGIMES
Cambodia ISC Mark Product Treatment of Domestically and Import Products:
Certification/Registrat - Application
ion - Domestic:
o Factory assessment
o Product Testing
- Import:
o Presentation of IECEE CB Test Certificate or other specifically recognized
certificate according to IEC standards mentioned in Regulations
VERSION 12 – as of May 2010

COUNTRY TYPES OF CON- MODE OF REGULATION

FORMITY ASSESS-
MENT REGIMES
- Issuing of Cambodian Registration Certificate
VERSION 12 – as of May 2010

VI. FLOWCHART OF MEMBER COUNTRIES’ REGIME

CAMBODIA
Flowchart of Certification of Registration

Manufacturers
Suppliers
Producers

PRODUCTS

NO Are products required to comply YES

with Cambodian mandatory
standards and technical regulations?

Test report by a Lab recognized by

ISC/MIME

Certificate by a Certification body

recognized by ISC/MIME

Registration Certificate

Labelling/Marking
Use of Cambodian safety mark

Sale
VERSION 12 – as of May 2010

VII. MAINS VOLTAGE, FREQUENCY AND MAINS PLUG CONFIGURATION

Country Mains Mains Applicable Mains Plug Configuration

VIII. CONTACT PERSON

Country Contact Person and Address
Cambodia CHAN BORIN
Deputy Director of Department of Industrial Standards of Cambodia ( ISC ), Ministry of Industry, Mines and Energy
# 538 National Road No. 2, Sangkat Chak-Ang Re Leu, Khan Mean Chey, Phnom Penh, CAMBODIA,
Phone: 855 12 751571, Fax: +855 23 216086 or +855 23 425052
Email: discinfo@[Link] ; or : chanborin@[Link]
Website: [Link]

14 of 120
Version 12 as of May 2010

INDONESIA
I. RATIONALE FOR REGULATION

COUNTRY RATIONALE FOR REGULATION

Indonesia Consumer Protection

II. REGULATION BODY

COUNTRY REGULATORY BODY

Indonesia Ministry of Industry.

Ministry of Energy and Mineral Resources.
Ministry of Trade

15 of 120
Version 12 as of May 2010

III. LEGISLATIVE FRAMEWORK

COUNTRY LEGISLATIVE FRAMEWORK

Indonesia Act No. 8 / 1999 concerning Consumer Protection

Government. Regulation No. 102/2000 concerning National Standardization

Decree of the Minister of Industry No. 86/M-IND/PER/9/2009 dated September 24, 2009 concerning
the Implementation of SNI in Industrial Sector (replacing Decree of MoI No.19/2006)

Decree of the Minister of Trade No. 14/M-DAG/PER/3/2007 dated March 7, 2007 concerning
Standardization of Services in the Field of Trade and Supervision over Traded Goods and Services
which are Technically Regulated based on Indonesian National Standard (SNI)

Decree of the Minister of Trade No. 30/M-DAG/PER/2007 dated July 7, 2007 concerning
Amendment to the Decree of the Minister of Trade No. 14/M-DAG/PER/2007 on Standardization of
Services in the Field of Trade and Supervision over Traded Goods and Services which are
Technically Regulated based on Indonesian National Standard (SNI)

16 of 120
Version 12 as of May 2010

IV. MANDATORY STANDARDS

STANDARDS
Domestic Please tick Relevant Extent of State reason
Country Product type or grouping box if
Standards International Alignment if MOD
mandatory Standards
Indonesia Incandescent lamps SNI 04-3560-1994
V IEC 60064 IDT
Self-ballast lamp for general lighting SNI 04-6504 -2001 V IEC 60968 IDT
service
Plugs and socket-outlets for household SNI 04-3892.1-2006 IEC 60884-1
and similar purposes. Part 1 : General Ed.3.0(2002),am.1
requirement (2006)
V IEC 60884-2-1 IDT
Ed.1.0(1987)
IEC 60884-2-3
Ed.1.0(1989)
Switches for household installations SNI 04-6203.1-2006 V IEC 60669-1 IDT
and similar fixed electric. Part 1: Ed.3.1(2000)
General requirements
Circuit breakers for over current SNI 04- V IEC 60898-1 IDT
protection for household and similar 6507.1/Amd1. 2006 Ed.1.2(2003)
installation. Part 1 : Circuit breaker for
ac operated

17 of 120
Version 12 as of May 2010

STANDARDS
Domestic Please tick Relevant Extent of State reason
Country Product type or grouping box if
Standards International Alignment if MOD
mandatory Standards
Electrical appliances for household SNI 04-6292.2.80- V IEC 60335-1; IDT
usages and other similar types of 2006 IEC 60335-2-80
safety products; Part 2-80. Special
requirements for electric fan
Lamp controlgears - Part 1: General SNI 04-6959.1- V IEC 61347-1 (2000- IDT
and safety requirements 2003 10)

Lamp controlgears - Part 2-3: Particular SNI 04-6959.2.3- V IEC 61347-2-3 (2000- IDT
requirements for a.c. supplied electronic 2003 10):
ballasts for fluorescent lamps

Residual current operated circuit - SNI 4 -6956.1-2003 V IEC 61008-1 (1996- IDT
breakers without integral overcurrent 12)
protection for household and similar
uses (RCCB) - Part 1: General rules
Residual current operated circuit- SNI 04-6956.2.1- V IEC 61008-2-1 (1990- IDT
breakers without integral overcurrent 2005 12):
protection for household and similar
uses (RCCB’s) - Part 2-1: Applicability
of the general rules to RCCB’s
functionally independent of line voltage
Luminaires - Part 1: General SNI 4 -6973.1-2005 V IEC 60598-1 (2003) IDT
requirements and tests

Luminaires - Part 2-1: Particular SNI 4 -6973.2.1- V IEC 60598-2-1 (1979) IDT
requirements - Fixed general purpose 2005
luminaires

Luminaires - Part 2-2: Particular SNI 4 -6973.2.2- V IEC 60598-2-2 (1997) IDT
requirements - Recessed luminaires 2005

18 of 120
Version 12 as of May 2010

STANDARDS
Domestic Please tick Relevant Extent of State reason
Country Product type or grouping box if
Standards International Alignment if MOD
mandatory Standards
Luminaires - Part 2-3: Particular SNI 4 -6973.2.3- V IEC 60598-2-3 (2002) IDT
requirements - Luminaires for road and 2005
street lighting

Luminaires - Part 2-5: Particular SNI 4 -6973.2.5- V IEC 60598-2-5 IDT

requirements – Floodlights 2005 (1998):

Primary Battery - part 1: General SNI 04-2051.1- V IDT

2004 IEC 60086-1 (2000)

Primary Battery - part 2: Electrical and SNI 04-2051.2- V IDT

Physical Requirement 2004 IEC 60086-2 (2000)

PVC insulated cables with a rated SNI 04-6629.2- V IEC 60227-2 IDT
voltage up to 450/750 V - Part 2: Test 2006
methods

PVC insulated cables with a rated SNI 04-6629.3- V IEC 60227-3 IDT
voltage up to 450/750 V - Part 3: Non- 2006
sheated cables for fixed wiring

PVC insulated cables with a rated SNI 04-6629.4- V IEC 60227-4 IDT
voltage up to 450/750 V - Part 4: 2006
Sheated cables for fixed wiring
PVC insulated cables with a rated SNI 04-6629.5- V IEC 60227-5 IDT
voltage up to 450/750 V - Part 5: 2006
Flexible cables

19 of 120
Version 12 as of May 2010

STANDARDS
Domestic Please tick Relevant Extent of State reason
Country Product type or grouping box if
Standards International Alignment if MOD
mandatory Standards
Power cables with extruded insulation SNI IEC 60502- V IEC 60502-1:2009 IDT
and their accessories for rated 1:2009
voltages from 1 kV (Um = 1,2 kV) up to
30 kV (Um = 36 kV) - Part 1: Cables
for rated voltages of 1 kV (Um = 1,2
kV) and 3 kV (Um = 3,6 kV)

Power cables with extruded insulation SNI IEC 60502-2 : V IEC 60502-2 : 2009 IDT
and their accessories for rated 2009
voltages from 1 kV (Um = 1,2 kV) up to
30 kV (Um = 36 kV) - Part 2: Cables
for rated voltages from 6 kV (Um = 7,2
kV) up to 30 kV (Um = 36 kV)

NEW DECREE OF MANDATORY STANDARDS

Decree of the Minister of Energy and Mineral Resources No. 15/2009 dated August 11, 2009 concerning the mandatory implementation of
Indonesian National Standard (SNI) for
- SNI 04-6959.1-2003 Lamp controlgears - Part 1: General and safety requirements
- SNI 04-6959.2.3-2003 Lamp controlgears - Part 2-3: Particular requirements for a.c. supplied electronic ballasts for fluorescent lamps

Decree of the Minister of Energy and Mineral Resources No. 16/2009 dated August 11, 2009 concerning the mandatory implementation of
Indonesian National Standard (SNI) for
SNI 4 -6956.1-2003 Residual current operated circuit - breakers without integral overcurrent protection for household and similar uses
(RCCB) - Part 1: General rules
SNI 04-6956.2.1-2005 Residual current operated circuit-breakers without integral overcurrent protection for household and similar uses
(RCCB’s) - Part 2-1: Applicability of the general rules to RCCB’s functionally independent of line voltage

Decree of the Minister of Energy and Mineral Resources No. 17/2009 dated August 11, 2009 concerning the mandatory implementation of
Indonesian National Standard (SNI) for
SNI 4 -6973.1-2005 Luminaires - Part 1: General requirements and tests

20 of 120
Version 12 as of May 2010

SNI 4 -6973.2.1-2005 Luminaires - Part 2-1: Particular requirements - Fixed general purpose luminaires
SNI 4 -6973.2.2-2005 Luminaires - Part 2-2: Particular requirements - Recessed luminaires
SNI 4 -6973.2.3-2005 Luminaires - Part 2-3: Particular requirements - Luminaires for road and street lighting
SNI 4 -6973.2.5-2005 Luminaires - Part 2-5: Particular requirements – Floodlights

Decree of the Minister of Industry No. 36/M-IND/PER/3/2009 dated March 27, 2009 concerning the mandatory implementation of Indonesian
National Standard (SNI) for
SNI 04-2051.1-2004 Primary Battery - part 1: General and
SNI 04-2051.2-2004 Primary Battery - part 2: Electrical and Physical Requirement

Decree of the Minister of Industry No. 42/M-IND/PER/3/2010 dated March 29, 2010 concerning the mandatory implementation of Indonesian
National Standard (SNI) for
SNI 04-6629.2-2006 PVC insulated cables with a rated voltage up to 450/750 V - Part 2: Test methods
SNI 04-6629.3-2006 PVC insulated cables with a rated voltage up to 450/750 V - Part 3: Non-sheated cables for fixed wiring
SNI 04-6629.4-2006 PVC insulated cables with a rated voltage up to 450/750 V - Part 4: Sheated cables for fixed wiring
SNI 04-6629.5-2006 PVC insulated cables with a rated voltage up to 450/750 V - Part 5: Flexible cables
SNI IEC 60502-1:2009 Power cables with extruded insulation and their accessories for rated voltages from 1 kV (Um = 1,2 kV) up to 30 kV
(Um = 36 kV) - Part 1: Cables for rated voltages of 1 kV (Um = 1,2 kV) and 3 kV (Um = 3,6 kV)
SNI IEC 60502-2 : 2009 Power cables with extruded insulation and their accessories for rated voltages from 1 kV (Um = 1,2 kV) up to 30 kV
(Um = 36 kV) - Part 2: Cables for rated voltages from 6 kV (Um = 7,2 kV) up to 30 kV (Um = 36 kV)

V. MODE OF REGULATION AND TYPES OF CONFORMITY ASSESSMENT REGIMES

COUNTRY TYPES OF CON- MODE OF REGULATION

FORMITY ASSESS-
MENT REGIMES

21 of 120
Version 12 as of May 2010

COUNTRY TYPES OF CON- MODE OF REGULATION

FORMITY ASSESS-
MENT REGIMES
Indonesia
Technical Regulation • Technical regulation on EEE by adopting partially or fully technical specification
based on SNI and/or parameter of SNI is stipulated by Ministerial Decree taking into account
safety, security, health, environment, moral hazard, and economical aspects, that
are equally imposed to both domestic and imported products which are traded in
Indonesian teritory.

• Manufacturers of EEE which are technically regulated based on SNI shall fulfill the
SNI requirements and shall affix the SNI mark on the products, packages and/or
label of their products

Product Registration • Pre-market surveillance over traded goods produced domestically, shall be done
to get NPB (for through Product Registration Number (Nomor Registrasi Produk - NRP)
imported products) or
NRP (for domestic
• Pre-market surveillance over imported of EEE shall be done through Goods
products)
Registration Letter (Surat Pendaftaran Barang – SPB) which includes Goods
Registration Number (Nomor Pendaftaran Barang – NPB),

• NRP and SPB shall be issued by the Director General of Foreign Trade c/o the
Director of Supervision and Quality Control of Goods (Direktur Pengawasan dan
Pengendalian Mutu Barang – Dir PPMB) Ministry of Trade

• NRP and NPB are valid for 3 (three) years and can be extended.

• NRP or NPB shall affix underneath SNI Mark and/or other recognized conformity
mark, on to their products or packages.

22 of 120
Version 12 as of May 2010

COUNTRY TYPES OF CON- MODE OF REGULATION

FORMITY ASSESS-
MENT REGIMES

Registration of CAB • CAB issuing an SNI Mark Product Certification can be a domestic or foreign
product certification body supported by accredited testing laboratories and/or
inspection institutions.

• Domestic CAB shall be accredited by KAN according to its scopes, CAB shall be
registered to the Secretariat General c/o Center for Standardization Ministry of
Trade.

• All CAB which have the scope of mandatory SNI’s requirements shall be accredited by
National Accreditation Body of Indonesia (KAN) and assigned by Minister of Industry

23 of 120
Version 12 as of May 2010

VI. FLOWCHART OF INDONESIA’S REGIME

NRP Issuance Process 5 Days

DIRECTORATE
OF PPMB
Verification
Receipt of Valid NRP
Document
validity
REGISTRATION

Documents Document
APPLICANT required : Verification Complete
1. CoC
[Link]
of Product
Market Area Not Valid

Incomplete Refusal
(max 3 days)

Refused

24 of 120
Version 12 as of May 2010

SPB/NPB Issuance Process 5 Days

DIRECTORATE
OF PPMB
Verification
of
Receipt Document
Valid SPB
REGISTRATION validity
Documents
required :
APPLICANT
1. API Document
2. Certificate Verification Complete
of
Conformity
3. BL /
Not Valid
Airway Bill /
DO
4. Invoice &
Packing List Refusal
Incomplete
5. Legalized (max 3 days)
documents

Refused

25 of 120
Version 12 as of May 2010

5 Days

CAB Registration Procedures

CENTER FOR Verification

STANDARDIZATION (PUSTAND) of Letter of
Receipt Document Valid approval
validity
REGISTRA-
Accredited TION
APPLICANT scope of Documents
(Domestic required :
Techni- Document
or Foreign [Link] status Comp-
CAB) cally Verification
of Product lete
Regulated Certification
Product Body
based on [Link]
SNI nal Structure Not Valid
and List of
Personnel
[Link] of
relevant
Laboratorium Incomplete Refusal
[Link] (max 3
of days)
Accreditation
and its scope
[Link] of Refused
product
certificate

26 of 120
Version 12 as of May 2010

VII. MAINS VOLTAGE, FREQUENCY AND MAINS PLUG CONFIGURATION

Country Mains Mains Applicable Mains Plug Configuration

Voltage Frequency Legislation Domestic Please tick Relevant Extent of Diagram of Mains Plug
and and Standard box if International Alignment Configuration-
Tolerance Tolerance mandatory Standard -
Indonesia 230 ± 5% 50 ± 5% SNI 04-3892.1-2006 V
Plugs and socket- IEC 60884-1
outlets for Ed.3.0(2002,am.1
household and (2006)
similar purposes. IEC 60884-2-1
Part 1 : General Ed.1.0(1987)
requirement IEC 60884-2-3
Ed.1.0(1989)
(0nly for the
safety)

• SNI 04-3892.2.3-
2000:Plugs and
Sockets-Outlets for
household and
similar purposes;
Part 2.3:Particular
Requirement for
switched socket
outlets without
interlock for fixed
installation.

27 of 120
Version 12 as of May 2010

Country Mains Mains Applicable Mains Plug Configuration

Voltage Frequency Legislation Domestic Please tick Relevant Extent of Diagram of Mains Plug
and and Standard box if International Alignment Configuration-
Tolerance Tolerance mandatory Standard -
• SNI 04-6202-
2000: Plugs and
Sockets-Outlets
and couplers for
industrial purposes;
Part 3: Particular
Requirement for
plugs, socket
outlets, connectors
and appliance inlets
for use in explosive
gas atmospheres.
• SNI 04-0225- V IEC 60364
2000/Amd1-2006 (series)
on Amendment 1 of
Indonesian National
Standard for
General
Requirements on
Electrical
Installation

28 of 120
Version 12 as of May 2010

VIII. MARKING/LOGO :

Affixing SNI and NRP:

0 4 - 6 5 0 4 - 2 0 0 1

NRP 1 0 1 - 0 1 0 - 0 0 0 0 0 1
Note :
101 : Product Certification Body certifying the products
010 : Factory location
000001 : Registration Number in Dit. of PPMB

29 of 120
Version 12 as of May 2010

Affixing SNI and NPB:

0 4 - 6 5 0 4 - 2 0 0 1

NPB 1 0 1 - 1 5 6 - 0 0 0 0 0 1

Note :
101 : Product Certification Body certifying the products
156 : Country of Origin
000001 : Registration number in Directorate of PPMB

IX. CONTACT PERSON

Country Contact Person and Address

Indonesia I Nyoman Supriyatna
Head of Center for Cooperation on Standardization - BSN
Manggala Wanabakti Building Block IV 4th Floor
Jl. Jend. Gatot Subroto, Senayan, Jakarta 10270 Indonesia
Phone : 62-21-5747043/44
Fax : 62-21-5747045

30 of 120
Version 12 as of May 2010

Country Contact Person and Address

E-mail : kerj_int@[Link], nyoman@[Link], nyoman_san_bali@[Link]

31 of 120
Version 12 as of May 2010

I. COUNTRIES WITH MANDATORY STANDARDS FOR GOVERNMENT PROCUREMENT ONLY

LAO PDR

I. RATIONALE FOR REGULATION

COUNTRY RATIONALE FOR REGULATION

Lao PDR Consumer's Rights and Benefits Protection. Promote and Facilitate the Producers of Goods and
Products

II. REGULATION BODY

COUNTRY REGULATORY BODY

Lao PDR Science, Technology and Environment Agency

Department of Intellectual Property, Standardization and Metrology

32 of 120
Version 12 as of May 2010

III. LEGISLATIVE FRAMEWORK

COUNTRY LEGISLATIVE FRAMEWORK

Lao PDR Decree of the Prime Minister regarding the Management on Standards and Quality of Products and
the Metrology Management

Quality Inspection of Import Goods

IV. MANDATORY STANDARDS

33 of 120
Country Total Product Type or grouping STANDARDS
Product Domestic Please tick Relevant Extent of State
Standards box if International Alignmen Reason
mandator Standards t if MOD.
y Version 12 as of May 2010
Lao 50 Double capped fluorescent lamps - Performance LS 12-2006 IEC 60081 Ed. 5.0 b

PDR specifications
Plugs and socket outlets for domestic and similar general LS 13-2006 IEC 60083 TR3 Ed. 3.0
b
use standardized in member countries of IEC
Polyvinyl chloride insulated cables of rated voltages up to LS 14-2006 IEC 60227-1Ed. 2.2 b
and including 450/750v Part1: General requirements
Polyvinyl chloride insulated cables of rated voltages up to LS 152006 IEC 60227-2Ed. 2.0 b
and including 450/750v Part2: Test methods
Polyvinyl chloride insulated cables of rated voltages up to LS 16-2006 IEC 60227-3Ed. 2.1 b
and including 450/750v Part3: Non - sheathed cables of
fixed wiring
Polyvinyl chloride insulated cables of rated voltages up to LS 17-2006 IEC 60227-4Ed. 2.1 b
and including 450/750v Part4: Sheathed cables for rated
wiring.
Polyvinyl chloride insulated cables of rated voltages up to LS 18-2006 IEC 60227-5Ed. 2.1 b
and including 450/750v Part5: Flexible cables (cords)
Polyvinyl chloride insulated cables of rated voltages up to LS 19-2006 IEC 60227-6 Ed. 2.0 b
and including 450/750v Part6: Lift cables and cables for
flexible connections
Polyvinyl chloride insulated cables of rated voltages up to LS 20-2006 IEC 60227-7Ed. 1.0 b
and including 450/750v Part7: Flexible cables screened
and unscreened with two or more conductors.
Safety of household and similar electrical appliances - LS 21-2006 IEC 60335-2-
10,Ed.4:1992
Part2: Particular requirements for floor treatment
machines and wet scrubbing machines.
Safety of household and similar electrical appliances - LS 22-2006 IEC 60335-2-
11,Ed.5:2000
Part2-11: Particular requirements for tumble dryers.
Safety of household and similar electrical appliances - LS 23-2006 IEC 60335-2-
12,Ed.4:1992
Part2: Particular requirements for warming plates and
similar appliances.
Safety of household and similar electrical appliances - LS 24-2006 IEC 60335-2-
16,Ed.4:1994
Part2 Particular requirements for food waste disposers.
Safety of household and similar electrical appliances - LS 25-2006 IEC 60335-2-
34,Ed.3:1999
Part2-34: Particular requirements for motor –
compressors.
Safety of household and similar electrical appliances - LS 26-2006
IEC 60335-2-
Part2: Particular requirements for electrical heat pumps,
40,Ed.3:1995
air - conditioners and dehumidifiers.
Safety of household and similar electrical appliances - LS 27-2006 IEC 60335-2-
37,Ed.4:2000
Part2-37: Particular requirements for commercial electrical 34 of 120
deep fat fryers.
Safety of household and similar electrical appliances - LS 28-2006 IEC 60335-2-
42,Ed.4:2000
Part2-42: Particular requirements for commercial electric
forced convection ovens, steam cookers and steam -
convection ovens
Version 12 as of May 2010

V. MODE OF REGULATION AND TYPES OF CONFORMITY ASSESSMENT REGIMES

COUNTRY TYPES OF CON- MODE OF REGULATION

FORMITY ASSESS-
MENT REGIMES
Lao PDR N/A N/A

VI. FLOWCHART OF MEMBER COUNTRIES’ REGIME

No Flowchart of Lao PDR’s

35 of 120
Version 12 as of May 2010

VII. MAINS VOLTAGE, FREQUENCY AND MAINS PLUG CONFIGURATION

Country Mains Mains Applicable Mains Plug Configuration

VIII. CONTACT PERSON

Country Contact Person and Address

Lao PDR Soumana CHOULAMANY

Director of Standards and Quality Division,
Department of Intellectual Property, Standardization and Metrology,
Nahaidio Rd,Vientiane,Lao PDR [Link]
Tel:856-21 240784 FAX:856-21 213472
E-mail: soumanac@[Link]

36 of 120
Version 12 as of May 2010

II. COUNTRIES WITH MANDATORY STANDARDS

MALAYSIA

I. RATIONALE FOR REGULATION

COUNTRY RATIONALE FOR REGULATION

Malaysia Ensure safety and Consumer protection.

II. REGULATION BODY

COUNTRY REGULATORY BODY

Malaysia Energy Commission (Suruhanjaya Tenaga)

III. LEGISLATIVE FRAMEWORK

COUNTRY LEGISLATIVE FRAMEWORK

Malaysia Electricity Supply Act 1990; and

Electricity Regulations 1994

37 of 120
Version 12 as of May 2010

VII. MANDATORY STANDARDS

Total Product type or

Country Product grouping STANDARDS
Domestic Standards Please Relevant International State reason if
tick box if Standards Extent of MOD
mandator Alignment
y
Malaysia 1 PLUG TOP (PLUGS)

Two pole plug

with supply cord MS 1578:2003 BS EN 50075:1991 IDT
(max. 2.5 A)
13A Fused plug MS 589:Part 1:1997 BS 1363:Part 1:1995 IDT
15A Plug MS 1577:2003 BS 546:1950 IDT

Appliance
Connectors MS IEC 60320-1:2003 9 IEC 60320-1:2001 IDT

Inter connection
Coupler MS IEC 60320-2-2:2003 9 IEC 60320-2-2:1998 IDT

Adaptor
(Multiways) MS 589 Part 3:1997 9 BS 1363:Part 3:1995 IDT

Integrated
Adaptor MS 1144:1998 9 BS 5733:1995 IDT

Cable connector
- (connecting MS IEC 60998-1:2005 9 IEC 60998-1:2002 IDT
device)

38 of 120
Version 12 as of May 2010

Total Product type or

Country Product grouping STANDARDS
Domestic Standards Please Relevant International State reason if
tick box if Standards Extent of MOD
mandator Alignment
y
- (connecting
device screw- MS IEC 60998-2-1:2005 9 IEC 60998-2-1:2002 IDT
type)
- (connecting
device screw MS IEC 60998-2-2:2005 9 IEC 60998-2-2:2002 IDT
less-type)
- (connecting
device with MS IEC 60998-2-3:2005 9 IEC 60998-2-3:2002 IDT
insulation-
piercing
clamping units)
- (twist-on
connecting MS IEC 60998-2-4:2005 9 IEC 60998-2-4:2002 IDT
device)

Connecting box MS IEC 60998-2-5:2005 9 IEC 60998-2-5:2002 IDT

Malaysia 2 SWITCHES AND DIMMERS

General purpose MS IEC 60669-1:2004 9 IEC 60669-1:2001 MOD Testing ambient

switches temperature =
25°C ± 5°C
(IEC amb temp =
20°C ± 5°C)
Electronic MS IEC 60669-2-1:2004 9 IEC 60669-2-1:2001 MOD Testing ambient
switches temperature =
25°C ± 5°C
(IEC amb temp =
20°C ± 5°C)

39 of 120
Version 12 as of May 2010

Total Product type or

Country Product grouping STANDARDS
Domestic Standards Please Relevant International State reason if
tick box if Standards Extent of MOD
mandator Alignment
y
Remote-control MS IEC 60669-2-2:2004 9 IEC 60669-2-2:2001 MOD Testing ambient
switches temperature =
25°C ± 5°C
(IEC amb temp =
20°C ± 5°C)
Time Delay MS IEC 60669-2-3:2004 9 IEC 60669-2-3:2001 MOD Testing ambient
Switches temperature =
25°C ± 5°C
(IEC amb temp =
20°C ± 5°C)
Cooker Control No corresponding MS 9 BS 4177:1992 IDT
Unit
Malaysia 3 SOCKET OUTLET 15A AND BELOW (with or without ELCB/RCCB)

Electric Shaver MS IEC 61558-1:2005 9 IEC 61558-1:1998 IDT

Socket Outlets MS IEC 61558-2-5:2005 9 IEC 61558-2-5:1997 IDT
AC-AC Adaptor / MS IEC 61558-2-6:2005 9 IEC 61558-2-6:1997 IDT
AC-DC Adaptor
AC-DC
Converter/ MS IEC 60065:2003 9 IEC 60065:2001 IDT
Adaptor (for
Audio-video
Equipment)
AC-DC
Converter/ MS IEC 60950-1:2003 IEC 60950:2001 IDT
Adaptor (for IT 9
Equipment)

40 of 120
Version 12 as of May 2010

Total Product type or

Country Product grouping STANDARDS
Domestic Standards Please Relevant International State reason if
tick box if Standards Extent of MOD
mandator Alignment
y
13A Socket- MS 589:Part 2:1997 9 BS 1363:Part 2:1995 IDT
outlet
13A Portable MS 589:Part 2:1997 9 BS 1363:Part 2:1995 IDT
Socket-outlet
15A Socket- MS 1577:2003 9 BS 546:1950 IDT
outlet
Portable MS 1579:2003 9 SS 448:2001 IDT
Two-pin Socket-
outlet
Malaysia 4 FLUORESCENT LAMPHOLDERS / STARTER HOLDER

Lampholder for MS IEC 60400:1999 9

tubular or
fluorescent
lamps MS IEC 60400:2006 9 IEC 60400:2004 IDT

Starterholders MS IEC 60400:1999 9

for tubular or
fluorescent
lamps MS IEC 60400:2006 9 IEC 60400:2004 IDT

Malaysia 5 CEILING ROSES

Ceiling Rose MS 770:1982 9 BS 67:1969 IDT

Malaysia 6 BAYONET CAPS AND MULTWAYS ADAPTORS

41 of 120
Version 12 as of May 2010

Total Product type or

Country Product grouping STANDARDS
Domestic Standards Please Relevant International State reason if
tick box if Standards Extent of MOD
mandator Alignment
y
Bayonet Cap MS 769:1982 9 No corresponding foreign IDT
Adaptor standard
Bayonet Cap MS 769:1982 9 No corresponding foreign IDT
Lampholder standard
Bayonet Lamp MS 769:1982 9 No corresponding foreign IDT
Cap standard
Malaysia 7 FLUORESCENT LAMPS FITTING EXCLUDING TUBES IF IMPORTED SEPARATELY

Fixed general MS IEC 60598-1:2003 9

purpose MS IEC 60598-2-1:1997 9
luminaries
or
MS IEC 60598-1:2003 9 IEC 60598-1:1999 IDT
MS IEC 60598-2-1:2006 9 IEC 60598-2-1:2003 IDT

Recessed MS IEC 60598-1:1997 9 IEC 60598-1:1996 IDT

luminary MS IEC 60598-2-2:1998 9 IEC 60598-2-2:1997 IDT

Glow-starter for MS IEC 60155:1996 9 IEC 60155:1993 IDT

tubular
fluorescent
Malaysia 8 CAPACITORS FOR FLUORESCENT LAMPS

42 of 120
Version 12 as of May 2010

Total Product type or

Country Product grouping STANDARDS
Domestic Standards Please Relevant International State reason if
tick box if Standards Extent of MOD
mandator Alignment
y
Capacitors for MS IEC 61048 :1999 9
use in tubular or
fluorescent lamp
circuit MS IEC 61048:2006 9 IEC 61048 :1999 IDT
MS IEC 61049:1999 9 IEC 61049 :1999 IDT

Malaysia 9 BALLAST FOR FLUORESCENT

Ballast for MS IEC 61347-1:2003 9 IEC 61347-1:2003 IDT

tubular MS IEC 61347-2-8:2003 9 IEC 61347-2-8:2000 IDT
fluorescent
lamps MS 141:Part 2:1993 9 IEC 60921:1988 with IDT
modification
Electronic MS IEC 61347-1:2003 9 IEC 61347-1:2003 IDT
Ballast MS IEC 61347-2-3:2003 9 IEC 61347-2-3:2000 IDT
MS IEC 60929:1995 9 IEC 60929:1990 IDT
Malaysia 10 CIRCUIT BREAKERS (INCLUDING AC CURRENT OPERATED LEAKAGE CIRCUIT BREAKERS AND MINIATURE
CIRCUIT BREAKERS)

Residual MS IEC 61008-1:2003 9 IEC 61008-1:2002 IDT

Current Circuit or or
Breakers
MS IEC 61008-1:2007 9 IEC 61008-1:2006 IDT
MS IEC 61008-2-1:2003 9 IEC 61008-2-1:2002 IDT
MS IEC 61008-2-2:2003 9 IEC 61008-2-2:2002 IDT

43 of 120
Version 12 as of May 2010

Total Product type or

Country Product grouping STANDARDS
Domestic Standards Please Relevant International State reason if
tick box if Standards Extent of MOD
mandator Alignment
y
RCBO MS IEC 61009-1:2003 9 IEC 61009-1:1996 IDT
MS IEC 61009-2-1:2003 9 IEC 61009-2-1:1991 IDT
MS IEC 61009-2-2:2003 9 IEC 61009-2-2:1991 IDT
Miniature Circuit MS IEC 60898-1:2003 9 IEC 60898-1:2002 IDT
Breaker (MCB) MS IEC 60898-2:2003 9 IEC 60898-2:2002 IDT
Fuse Base & MS IEC 60269-1:2003 9 IEC 60269-1:1998 IDT
Carrier up to No corresponding MS 9 IEC 60269-2:1995 IDT
32A
Fuse/Fuse Link MS IEC 60269-2-1:2003 9 IEC 60269-2-1:1996 IDT
up to 63A MS 5186-3:2003 9 IEC 60269-3:1987 IDT
MS IEC 60269-3-1:2003 IEC 60269-3-1:2001 IDT
Switch fuse up MS IEC 60947-1:1996 9 IEC 60269-1:1996 IDT
to 63A MS IEC 60947-3:2000 9 IEC 60269-3:1999 IDT
Malaysia 11 WATER HEATERS (INCLUDING HEATING ELEMENTS IF IMPORTED SEPARATELY)

Electric MS IEC 60335-1:2003 9 IEC 60335-1:2001 Testing ambient

Stationary temperature =
MS 1597-2-35:2003 9 IEC 60335-2-35:2002 NEQ 25°C ± 5°C
Instantaneous with modification
Water Heaters (IEC amb temp =
20°C ± 5°C)
Electric Storage MS IEC 60335-1:2003 9 IEC 60335-1:2001 IDT
Water Heaters MS IEC 60335-2-23:2005 9 IEC 60335-2-21:2004 IDT
Malaysia 12 HAND OPERATED HAIR DRYERS

44 of 120
Version 12 as of May 2010

Total Product type or

Country Product grouping STANDARDS
Domestic Standards Please Relevant International State reason if
tick box if Standards Extent of MOD
mandator Alignment
y
Electric Hair MS IEC 60335-1:2003 9 IEC 60335-1:2001 IDT
Dryers MS IEC 60335-2-23:2003 9 IEC 60335-2-23:2003 IDT
Electric Hair MS IEC 60335-1:2003 9 IEC 60335-1:2001 IDT
Styling Sets MS IEC 60335-2-23:2003 9 IEC 60335-2-23:2003 IDT

Malaysia 13 DOMESTIC LIGHT FITTINGS HAVING ACCESSIBLE METAL PARTS

Electric MS IEC 60598-1:2003 9 IEC 60598-1:2000 IDT

Standing Lamps MS IEC 60598-2-4:2003 9 IEC 60598-2-4:1997 IDT
Electric Table MS IEC 60598-1:2003 9 IEC 60598-1:2000 IDT
Lamps MS IEC 60598-2-4:2003 9 IEC 60598-2-4:1997 IDT
Electric Hand MS IEC 60598-1:1997 9 IEC 60598-1:1996 IDT
Lamps MS IEC 60598-2-8:1998 9 IEC 60598-2-8:1996 IDT
Malaysia 14 ELECTRIC KETTLES (INCLUDING HEATING ELEMENTS IF IMPORTED SEPARATELY)

Electric MS IEC 60335-2-12:2003 9 IEC 60335-2-12:2002 IDT

Warming Plate

Electric Coffee / MS IEC 60335-2-15:2004 9 IEC 60335-2-15:2002 IDT

Tea Maker
Electric Food MS IEC 60335-2-15:2004 9 IEC 60335-2-15:2002 IDT
Steamer
Electric Egg MS IEC 60335-2-15:2004 9 IEC 60335-2-15:2002 IDT
Boiler

45 of 120
Version 12 as of May 2010

Total Product type or

Country Product grouping STANDARDS
Domestic Standards Please Relevant International State reason if
tick box if Standards Extent of MOD
mandator Alignment
y
Electric Jug MS IEC 60335-2-15:2004 9 IEC 60335-2-15:2002 IDT

Electric Slow MS IEC 60335-2-15:2004 9 IEC 60335-2-15:2002 IDT

Cooker
Electric Steam MS IEC 60335-2-15:2004 9 IEC 60335-2-15:2002 IDT
Boat
Electric Kettle MS IEC 60335-2-15:2004 9 IEC 60335-2-15:2002 IDT

Electric Water MS IEC 60335-2-15:2004 9 IEC 60335-2-15:2002 IDT

Pot
Electric Steam MS IEC 60335-2-15:2004 9 IEC 60335-2-15:2002 IDT
Generator
Appliance
Electric Heating MS IEC 60335-2-15:2004 9 IEC 60335-2-15:2002 IDT
Elements for
Kettle
Electric Deep MS IEC 60335-2-13:1995 9 IEC 60335-2-13:1993 IDT
Fryer
Electrical Multi- MS IEC 60335-2-13:1995 9
purpose cookers or
MS IEC 60335-2-13:2005 9 IEC 60335-2-13:2002 IDT
MS IEC 60335-2-9:2006 9 IEC 60335-2-9:2004 IDT
MS IEC 60335-2-15:2004 9 IEC 60335-2-15:2002 IDT

46 of 120
Version 12 as of May 2010

Total Product type or

Country Product grouping STANDARDS
Domestic Standards Please Relevant International State reason if
tick box if Standards Extent of MOD
mandator Alignment
y
Electric Built-in MS IEC 60335-2-36:2003 9 IEC 60335-2-36:2002 IDT
Hob
Malaysia 15

Electric Iron MS IEC 60335-2-3:1995 9 IEC 60335-2-3:1993 IDT

Malaysia 16 SHAVER

Electric Hair MS IEC 60335-2-8:2002 9 IEC 60335-2-8:1992 IDT

Clipper
Electric Shaver MS IEC 60335-2-8:2002 9 IEC 60335-2-8:1992 IDT
Malaysia 17 FOOD MAXER / BLENDER (KITCHEN MACHINE)
Electric Blander MS IEC 60335-2-14:2003 9 IEC 60335-2-14:2002 IDT
Electric Chopper MS IEC 60335-2-14:2003 9 IEC 60335-2-14:2002 IDT

Electric Food MS IEC 60335-2-14:2003 9 IEC 60335-2-14:2002 IDT

Processor
Electric Juice MS IEC 60335-2-14:2003 9 IEC 60335-2-14:2002 IDT
Extractor
Electric Grinder MS IEC 60335-2-14:2003 9 IEC 60335-2-14:2002 IDT
Electric Mixer MS IEC 60335-2-14:2003 9 IEC 60335-2-14:2002 IDT
Malaysia 18 IMMERSION WATER HEATERS

47 of 120
Version 12 as of May 2010

Total Product type or

Country Product grouping STANDARDS
Domestic Standards Please Relevant International State reason if
tick box if Standards Extent of MOD
mandator Alignment
y
Electric Fixed MS IEC 60335-2-73:2003 9 IEC 60335-2-73:2002 IDT
Immersion
Heater
Portable MS IEC 60335-2-74:1996 9 IEC 60335-2-74:1994 IDT
Immersion
Heater
Malaysia 19 HI-FI SETS

Sub-woofer MS IEC 60065:2003 9 IEC 60065:2001 IDT

Amplifier MS IEC 60065:2003 9 IEC 60065:2001 IDT
Cassette Player MS IEC 60065:2003 9 IEC 60065:2001 IDT

Equalizers/ MS IEC 60065:2003 9 IEC 60065:2001 IDT

Mixers
Hi-fi System MS IEC 60065:2003 9 IEC 60065:2001 IDT
Karaoke MS IEC 60065:2003 9 IEC 60065:2001 IDT
Laser Disc MS IEC 60065:2003 9 IEC 60065:2001 IDT
Player
PA System MS IEC 60065:2003 9 IEC 60065:2001 IDT

Portable Hi-fi MS IEC 60065:2003 9 IEC 60065:2001 IDT

System

48 of 120
Version 12 as of May 2010

Total Product type or

Country Product grouping STANDARDS
Domestic Standards Please Relevant International State reason if
tick box if Standards Extent of MOD
mandator Alignment
y
Portable Radio MS IEC 60065:2003 9 IEC 60065:2001 IDT
Cassette Player
/ Recorder
Radio MS IEC 60065:2003 9 IEC 60065:2001 IDT
Radio Alarm MS IEC 60065:2003 9 IEC 60065:2001 IDT
Tuner / Receiver MS IEC 60065:2003 9 IEC 60065:2001 IDT

Turn tables / MS IEC 60065:2003 9 IEC 60065:2001 IDT

Record Players
Compact Disc MS IEC 60065:2003 9 IEC 60065:2001 IDT
Players
Malaysia 20 MOSQUITO MATT VAPORISER

Mosquito Matt MS IEC 60335-1:2003 9 IEC 60335-1:2001 IDT

Vapor MS IEC 60335-2- 9 IEC 60335-2-101:2001 IDT
101:2003
Electric Aroma MS IEC 60335-1:2003 9 IEC 60335-1:2001 IDT
Vapor MS IEC 60335-2- 9 IEC 60335-2-101:2001 IDT
101:2003
Malaysia 21 TOASTERS/OVENS

Electric Bread MS IEC 60335-1:2003 9 IEC 60335-1:2001 IDT

Makers MS IEC 60335-2-9:2005 9 IEC 60335-2-9:2002 IDT

49 of 120
Version 12 as of May 2010

Total Product type or

Country Product grouping STANDARDS
Domestic Standards Please Relevant International State reason if
tick box if Standards Extent of MOD
mandator Alignment
y
Electric Bread MS IEC 60335-1:2003 9 IEC 60335-1:2001 IDT
Toasters MS IEC 60335-2-9:2005 9 IEC 60335-2-9:2002 IDT
Electric Portable MS IEC 60335-1:2003 9 IEC 60335-1:2001 IDT
Ovens MS IEC 60335-2-9:2005 9 IEC 60335-2-9:2002 IDT
Portable MS IEC 60335-1:2003 9 IEC 60335-1:2001 IDT
Induction MS IEC 60335-2-9:2005 9 IEC 60335-2-9:2002 IDT
Cooker
Electric Grillers MS IEC 60335-1:2003 9 IEC 60335-1:2001 IDT
MS IEC 60335-2-9:2005 9 IEC 60335-2-9:2002 IDT
Electric MS IEC 60335-1:2003 9 IEC 60335-1:2001 IDT
Sandwich MS IEC 60335-2-9:2005 9 IEC 60335-2-9:2002 IDT
Makers / Waffle
Makers

Electric MS IEC 60335-1:2003 9 IEC 60335-1:2001 IDT

Roasters MS IEC 60335-2-9:2005 9 IEC 60335-2-9:2002 IDT

Electric MS IEC 60335-1:2003 9 IEC 60335-1:2001 IDT

Stationary MS IEC 60335-2-6:1999 9 IEC 60335-2-6:2002 IDT
Electric Ovens
or
MS 1597:Part 2-6:2003 9 IDT

50 of 120
Version 12 as of May 2010

Total Product type or

Electric MS IEC 60335-2-25:1995 9 IEC 60335-2-25:1993 IDT

Microwave Oven

Malaysia 22 FANS
MS 1219:
Electric moving- MS IEC 60335-1:1995 9 IEC 60335-1:1991 IDT
louvre fans & MS 1219:Part 2:2002 9 IEC 60335-2-80:1997 MOD New requirement
regulators for detachable part,
MS 1220:2001 9 IEC 60879:1986 with MOD temperature
modification marking,
maintenance
or 9 or
instruction,
MS IEC 60335-1:2003 9 IEC 60335-1:2001 IDT moisture
resistance, supply
MS 1597:Part 2-80:2007 9 IEC 60335-2-80:2004 MOD connection,
MS 1220:2001 MS 1220:2001 MOD external flexible
cord and
mechanical
strength

51 of 120
Version 12 as of May 2010

Total Product type or

Country Product grouping STANDARDS
Domestic Standards Please Relevant International State reason if
tick box if Standards Extent of MOD
mandator Alignment
y
Electric ceiling MS IEC 60335-1:1995 9 IEC 60335-1:1991 IDT
fans & MS 1219:Part 2:2002 9 IEC 60335-2-80:1997 MOD MS 1220:
regulators
MS 1220:2001 9 IEC 60879:1986 with MOD 1) Cl 7.2:
modification statement ‘with
at least five
or or running
IEC 60335-1:2001 positions’ is
MS IEC 60335-1:2003 9 IDT replaced by
MS 1597:Part 2-80:2007 9 IEC 60335-2-80:2004 MOD ‘with at least
MS 1220:2001 three running
MS 1220:2001 9 MOD positions’
Electric auto MS IEC 60335-1:1995 9 IEC 60335-1:1991 IDT 2) Clause 10.3.2:
fans & MS 1219:Part 2:2002 9 IEC 60335-2-80:1997 MOD Rating of
regulators frequency is
MS 1220:2001 9 IEC 60879:1986 with MOD defined to suit
modification local conditions
or or
MS IEC 60335-1:2003 9 IEC 60335-1:2001 IDT
MS 1597:Part 2-80:2007 9 IEC 60335-2-80:2004 MOD MS 1597:
MS 1220:2001 9 MS 1220:2001 MOD

52 of 120
Version 12 as of May 2010

Total Product type or

Country Product grouping STANDARDS
Domestic Standards Please Relevant International State reason if
tick box if Standards Extent of MOD
mandator Alignment
y
Electric pedestal MS IEC 60335-1:1995 9 IEC 60335-1:1991 IDT 1) Clause 3.1.9 of
IEC 60335-2-7
fans & MS 1219:Part 2:2002 9 IEC 60335-2-80:1997 MOD :2003
regulators
MS 1220:2001 9 IEC 60879:1986 with MOD Water temp.
modification changed
or or from
MS IEC 60335-1:2003 9 IEC 60335-1:2001 IDT 15°C + 5°C to
IEC 60335-2-80:2004 25°C + 5°C
MS 1597:Part 2-80:2007 9 MOD
MS 1220:2001 9 MS 1220:2001 MOD 2) Clause 6.2 in
Annex BB of
Electric table MS IEC 60335-1:1995 9 IEC 60335-1:1991 IDT IEC 60335-2-7
fans & :2003
MS 1219:Part 2:2002 9 IEC 60335-2-80:1997 MOD
regulators Water temp.
MS 1220:2001 9 IEC 60879:1986 with MOD changed
modification
from
or or
15°C + 5°C to
MS IEC 60335-1:2003 9 IEC 60335-1:2001 IDT 25°C + 5°C
MS 1597:Part 2-80:2007 9 IEC 60335-2-80:2004 MOD
MS 1220:2001 9 MS 1220:2001 MOD

53 of 120
Version 12 as of May 2010

Total Product type or

Country Product grouping STANDARDS
Domestic Standards Please Relevant International State reason if
tick box if Standards Extent of MOD
mandator Alignment
y
Electric wall fans MS IEC 60335-1:1995 9 IEC 60335-1:1991 IDT
& regulators MS 1219: Part 2:2002 9 IEC 60335-2-80:1997 MOD
MS 1220:2001 9 IEC 60879:1986 with MOD
modification
or or
MS IEC 60335-1:2003 9 IEC 60335-1:2001 IDT
MS 1597:Part 2-80:2007 9 IEC 60335-2-80:2004 MOD
MS 1220:2001 9 MS 1220:2001 MOD

Electric MS 1219:Part 2: 2002 9 IEC 60335-2-80:1997 IDT

ventilating fans or or
& regulators
MS 1597:Part 2-80:2007 9 IEC 60335-2-80:2004 MOD
Electric range MS IEC 60335-1:2003 9 IEC 60335-1:2001 IDT
hoods MS IEC 60335-2-31:2003 IEC 60335-2-31:2002 IDT
Electric Air MS IEC 60335-2-98:2003 9 IEC 60335-2-98:2002 IDT
Cooler
Malaysia 23 TELEVISIONS

Television MS IEC 60065:2003 9 IEC 60065:2001 IDT

Projection MS IEC 60065:2003 9 IEC 60065:2001 IDT
Television
Malaysia 24 VACUUM CLEANER

54 of 120
Version 12 as of May 2010

Total Product type or

Country Product grouping STANDARDS
Domestic Standards Please Relevant International State reason if
tick box if Standards Extent of MOD
mandator Alignment
y
Carpet Cleaner MS IEC 60335-1:1995 9 IEC 60335-1:1991 IDT
MS IEC 60335-2-2:1995 9 IEC 60335-2-2:1993 IDT
Vacuum Cleaner MS IEC 60335-1:1995 9 IEC 60335-1:1991 IDT
& Accessory MS IEC 60335-2-2:1995 9 IEC 60335-2-2:1993 IDT
Malaysia 25 VIDEO PLAYERS

Video compact MS IEC 60065:2003 9 IEC 60065:2001 IDT

disc players

Laser Disc MS IEC 60065:2003 9 IEC 60065:2001 IDT

Player

Video Cassette MS IEC 60065:2003 9 IEC 60065:2001 IDT

Recorder /
Players

Digital versatile MS IEC 60065:2003 9 IEC 60065:2001 IDT

disc players

Video Rewinder MS IEC 60065:2003 9 IEC 60065:2001 IDT

Children Video MS IEC 60065:2003 9 IEC 60065:2001 IDT

Games

55 of 120
Version 12 as of May 2010

Total Product type or

Country Product grouping STANDARDS
Domestic Standards Please Relevant International State reason if
tick box if Standards Extent of MOD
mandator Alignment
y
Malaysia 26 WASHING MACHINES

Electric Washing MS IEC 60335-1:2003 9 IEC 60335-1:2001 IDT

Machines MS IEC 60335-2-4:2003 9 IEC 60335-2-4:2002 IDT
MS 1597:Part 2-7:2003 9 IEC 60335-2-7:2002 with MOD MS 1597
modification
1) Clause 3.1.9 of
Electric Cloth MS IEC 60335-1:2003 9 IEC 60335-1:2001 IDT IEC 60335-2-7
Dryers MS 1597:Part 2-43:2005 9 IEC 60335-2-43:2002 MOD
:2003
with modification Water temp.
changed
from
15°C + 5°C to
25°C + 5°C

2) Clause 6.2 in
Annex BB of
IEC 60335-2-7
:2003
Water temp.
changed
from
15°C + 5°C to
25°C + 5°C

Malaysia 27 REFRIGERATOR

56 of 120
Version 12 as of May 2010

Total Product type or

Country Product grouping STANDARDS
Domestic Standards Please Relevant International State reason if
tick box if Standards Extent of MOD
mandator Alignment
y
Electric MS IEC 60335-1:1995 9 IEC 60335-1991 IDT
Refrigerator MS IEC 60335-2-24:2002 9 IEC 60335-2-24:1997 IDT
Electric Freezer MS IEC 60335-1:1995 9 IEC 60335-1991 IDT
MS IEC 60335-2-24:2002 9 IEC 60335-2-24:1997 IDT
Electric Minibar MS IEC 60335-1:1995 9 IEC 60335-1991 IDT
MS IEC 60335-2-24:2002 9 IEC 60335-2-24:1997 IDT
Malaysia 28 ELECTRIC RICE COOKERS
Rice cookers MS IEC 60335-1:2003 9 IEC 60335-1:2001 IDT
MS IEC 60335-2-15:2004 9 IEC 60335-2-15:2002 IDT
Malaysia 29 CHRISTMAS LIGHT
Lighting Chain MS IEC 60598-1:1997 9 IEC 60598-1:1996 IDT
MS IEC 60598-2-20:1998 9 IEC 60598-2-20:1996 IDT
Malaysia 30 DOMESTIC POWER TOOLS

Electric Circular MS IEC 60745-1:2005 9 IEC 60745-1:2001 IDT

Saw and MS IEC 60745-2-5:2003 9 IEC 60745-2-5:2003 IDT
Circular Knife
(Cutting Blade
up to 160 mm)
Electric Drill MS IEC 60745-1:2005 9 IEC 60745-1:2001 IDT
(Drill bit size up MS IEC 60745-2-1:2005 9 IEC 60745-2-1:2003 IDT
to 10 mm)

57 of 120
Version 12 as of May 2010

Total Product type or

Country Product grouping STANDARDS
Domestic Standards Please Relevant International State reason if
tick box if Standards Extent of MOD
mandator Alignment
y
Electric Grinder MS IEC 60745-1:2005 9 IEC 60745-1:2001 IDT
(up to 100 mm) MS IEC 60745-2-3:2005 9 IEC 60745-2-3:1984 IDT
Electric Sanders MS IEC 60745-1:2005 9 IEC 60745-1:2001 IDT
(up to 300 W) MS IEC 60745-2-4:2005 9 IEC 60745-2-4:2002 IDT
Electric spray MS IEC 60745-1:2005 9 IEC 60745-1:2001 IDT
gun for non- MS IEC 60745-2-7:2005 9 IEC 60745-2-7:1989 IDT
flammable liquid
(up to 100 bars)

Electric Jig and MS IEC 60745-1:2005 9 IEC 60745-1:2001 IDT

Sabre Saw (up MS IEC 60745-2-11:2005 9 IEC 60745-2-11:2003 IDT
to 60 mm)
Electric Planer MS IEC 60745-1:2005 9 IEC 60745-1:2001 IDT
(up to 500 W) MS IEC 60745-2-14:2006 9 IEC 60745-2-14:1984 IDT
Trimmers (up to MS IEC 60745-1:2005 9 IEC 60745-1:2001 IDT
300 W) MS IEC 60745-2-15:2006 9 IEC 60745-2-15:1984 IDT
Electric hedge MS IEC 60745-1:2005 9 IEC 60745-1:2001 IDT
trimmer and MS IEC 60745-2-15:2006 9 IEC 60745-2-15:1984 IDT
Grass shear (up
to 750 W)

Electric Router MS IEC 60745-1:2005 9 IEC 60745-1:2001 IDT

and trimmer (up MS IEC 60745-2-17:2006 9 IEC 60745-2-17:2003 IDT
to 500 W)

58 of 120
Version 12 as of May 2010

Total Product type or

Country Product grouping STANDARDS
Domestic Standards Please Relevant International State reason if
tick box if Standards Extent of MOD
mandator Alignment
y
High Pressure MS IEC 60335-1:2003 9 IEC 60335-1:2001 IDT
Cleaner MS IEC 60335-2-79:2007 9 IEC 60335-2-79:2005 IDT

Sewing Machine MS IEC 60335-1:2003 9 IEC 60335-1:2001 IDT

MS IEC 60335-2-28:2003 9 IEC 60335-2-28:2002 IDT
Electric MS IEC 60335-1:2003 9 IEC 60335-1:2001 IDT
Soldering Iron MS IEC 60335-2-45:2002 9 IEC 60335-2-45:1996 IDT

Portable Battery MS IEC 60335-1:2003 9 IEC 60335-1:2001 IDT

Charger (up to MS IEC 60335-2-29:2003 9 IEC 60335-2-29:2002 IDT
12V)
Malaysia 31 WIRES / CABLES CORDS (NON-ARMOURED) 0.5 SQ mm TO 35 SQ mm

Insulated flexible MS 140:1987 9 BS 6004:1984 -

cord and cable or
IEC 60227-1:1993 NEQ
IEC 60227-5:1998 NEQ
Polyvinyl MS 140:1987 9 BS 6004:1984 -
chloride or
Insulated flexible
cords IEC 60227-1:1993 NEQ
IEC 60227-5:1998 NEQ

59 of 120
Version 12 as of May 2010

Total Product type or

Country Product grouping STANDARDS
Domestic Standards Please Relevant International State reason if
tick box if Standards Extent of MOD
mandator Alignment
y
Rubber MS 140:1987 9 BS 6500:1984 -
insulated cord or
and flexible
cables IEC 60245-1:1998 NEQ
IEC 60245-4:1994 NEQ
PVC-insulated MS 136: 1995 9 BS 6004:1991 -
cable (non-
armoured) for
electric power
and supply

V. MODE OF REGULATION AND TYPES OF CONFORMITY ASSESSMENT REGIMES

60 of 120
Version 12 as of May 2010

COUNTRY TYPES OF CON- MODE OF REGULATION

FORMITY ASSESS-
MENT REGIMES
Malaysia Registration/ A certificate of approval is required. To obtain approval, the following are needed:
Certification • Test reports from local or foreign laboratories which are acceptable to ST.
• Submission of Form ST (PE) 3, test report and certificate.
• Enter the SIRIM Product Certification Scheme/SIRIM Batch Testing Scheme (every
consignment is subjected to inspection and testing)
• Use of SIRIM’s label

VI. FLOWCHART OF MEMBER COUNTRIES’ REGIME

61 of 120
Version 12 as of May 2010

To apply for the Certificate of Approval from ST

Submission of Form ST(PE)3, test reports and certificate.

The test reports and certificate are from local / foreign laboratories
which are recognized by ST/DSM (Department of Standard Malaysia)
Info booklet and Application Form – Website : [Link]

After obtaining Certificate of Approval (COA) from ST,

applicant needs to enter the SIRIM Product
Certification Scheme/SIRIM Batch Testing Scheme
(every Consignment Test at SIRIM is subject to
inspection and testing)

Use of SIRIM’s Label

VII. MAINS VOLTAGE, FREQUENCY AND MAINS PLUG CONFIGURATION

Country Mains Mains Applicable Mains Plug Configuration

62 of 120
Version 12 as of May 2010

Voltage Frequency Legislation Domestic Please tick Relevant Extent of Diagram of Mains Plug Configuration-
and and Standard box if International Alignment
Tolerance Tolerance mandatory Standard -
Malaysia 240 volts 50 Hz NA MS 589:Pt.1:1997 9 BS 1363:Pt.1: -
single ± 1% (for 3-pin 13A) & 1995
phase BS 546:1950
MS 1577:2003 (for
tolerance
3-pin 15A)
+5% -10%
rectangular type
plug

415 volts 50 Hz NA - - -

three phase ± 1%
tolerance
+5% -10%

VIII. CONTACT PERSON

Country Contact Person and Address

Malaysia Ismail Bin Anuar Muhammad Sharul Azam Abdul Rahim

Director, Deputy Director,
Department of Electrical Safety, Department of Electrical Safety,
Energy Commission Energy Commission
Level 10, Menara TH Perdana, Level 10, Menara TH Perdana,
1001, Jalan Sultan Ismail, 50250 Kuala Lumpur, Malaysia 1001, Jalan Sultan Ismail, 50250 Kuala Lumpur, Malaysia
Contact no:(603) 2612 5403 Contact no:(603) 2612 5408
Fax no: (603) 2691 5584 Fax no: (603) 2691 5584
Email: ismail@[Link] Email: azam@[Link]
Website: [Link] Website: [Link]

63 of 120
Version 12 as of May 2010

MYANMAR
I. RATIONALE FOR REGULATION

COUNTRY RATIONALE FOR REGULATION

Myanmar Ensure Safety and Consumer protection.

II. REGULATION BODY

COUNTRY REGULATORY BODY

Myanmar Ministry of Industry (1)

Directorate of Industrial Supervision and Inspection

Electrical Inspection Department

III. LEGISLATIVE FRAMEWORK

COUNTRY LEGISLATIVE FRAMEWORK

Myanmar Electricity Law (1984)

64 of 120
Version 12 as of May 2010

IV. MANDATORY STANDARDS

IV. MANDATORY STANDARDS
Country Total Product Type STANDARDS
Product or grouping Domestic Standards Please tick Relevant International Extent Aligment State reason if MOD
box if Standards
mandatory

Myanmar 22 [Link] Stove IEC 60335-2-6

(for hot plate& similar
appliance)
[Link] IEC 60065 :2001
[Link]-Insulated IEC 60227-1:1993 Ed2,
copper cable of rated Amd.1:1995,Amd.2:1998,
up to and including IEC 60227-2:1997 Ed 2,
450/750 V. IEC 60227-3:1997 Ed 2,
IEC 60227-4-1997 Ed 2,
BS 6500:1969,IEC 228:
1978,BS 6004:1995.
[Link]-insulated,PVC- IEC 60502-1:1994,
sheathed Cable up to BS 6004:1969,BS 6346/69
and including 1 kV.
[Link] Fixed IEC 60335-1,Ed 3,

65 of 120
Version 12 as of May 2010

immersion Heater IEC 60335-2-73,74 Ed 1:

(Safety) 1996
[Link] Motor (Safety) IEC 60335-2-34 :2000

Country Total Product Type STANDARDS

Product or grouping Domestic Standards Please tick Relevant International Extent Aligment State reason if MOD
box if Standards
mandatory
Myanmar [Link] pump(Safety) IEC 60335-2-40 :2000
[Link] IEC 60335-1:1991,Amd.1:
1994,IEC 60335-2-80:2000,
IEC 60879.
[Link](Electric moving IEC 60335-1:2001,
louvre fans & IEC 60335-2-80 :2000
regulator IEC 60879.
[Link] Lamp IEC 972,BS 1853:1956
[Link] Phase Distri- IEC 60076-1:
bution Transformer IEC 60076-3:
IEC 60076-4:
IEC 60156
[Link] Tension Switch IEC 947-2 :1995
board(including
Circuit

66 of 120
Version 12 as of May 2010

Breaker)
[Link] Ballast IEC 60928:1995,
IEC 60929:1990.
[Link] Lamps IEC 60400:1996.
Fitting(including Starter)

Country Total Product Type STANDARDS

Product or grouping Domestic Standards Please tick Relevant International Extent Aligment State reason if MOD
box if Standards
mandatory

67 of 120
Version 12 as of May 2010

1993, Amd.1+Amd.2:1999
[Link] IEC 209:1970,BS 215-2:1956.
[Link] Phase IEC 129:
Disconnecting Switch IEC 265:

V. MODE OF REGULATION AND TYPES OF CONFORMITY ASSESSMENT REGIMES

COUNTRY TYPES OF CON- MODE OF REGULATION

FORMITY ASSESS-
MENT REGIMES
Myanmar
Treatment of Domestically Produced Equipment

• Products have to be registered at the Electrical Inspection Department.

Treatment of Imports

• British and Japanese standards are used.

68 of 120
Version 12 as of May 2010

VII. FLOWCHART OF MEMBER COUNTRIES’ REGIME

No flowchart

VII. MAINS VOLTAGE, FREQUENCY AND MAINS PLUG CONFIGURATION

Country Mains Mains Applicable Mains Plug Configuration
Voltage Frequency Legislation Domestic Please tick Relevant Extent of Diagram of Mains Plug Configuration-
and and Standard box if International Alignment
Tolerance Tolerance mandatory Standard -
Myanmar

VIII. CONTACT PERSON

Country Contact Person and Address

Myanmar U Pyi Soe

President
Electrical and Electronic Standardization Committee
Myanmar Industrial Development Committee
No. 35 Kyaikwine Pagoda Road
Mayangone Township Yangon
Myanmar
Contact No.: 0951 – 01- 664293
Fax. No.: 0951 01 566066/ 665292 / 254961

69 of 120
Version 12 as of May 2010

PHILIPPINES

I. RATIONALE FOR REGULATION

COUNTRY RATIONALE FOR REGULATION

Philippines Upgrade the quality of products.

Protect and safeguard the interest of consumers especially in matters of health and safety.

II. REGULATION BODY

COUNTRY REGULATORY BODY

Philippines Bureau of Product Standards (BPS) under the Department of Trade and Industry (DTI).

III. LEGISLATIVE FRAMEWORK

COUNTRY LEGISLATIVE FRAMEWORK

Philippines Republic Act 4109

70 of 120
Version 12 as of May 2010

IV. MANDATORY STANDARDS

Country Total Product STANDARDS
Prod type or Domestic Please tick Relevant Extent of State reason if MOD
box if
uct grouping Standards mandatory International Alignment
Standards
Philippines Ballast for PNS 12-1:1996 ➝ IEC 920:1990 IDT
tubular Amd. 02:1997 Amd. 01:1993
fluorescent Amd. 02:1995
lamps – Safety
Ballast for PNS 12-2:1996 ➝ IEC 921:1990 IDT
tubular Amd. 01 & Amd. 01:1990
fluorescent 02:1997 Amd. 02:1994
lamps -
Performance
Lamps & related PNS 12-3:2000 ➝ - -
equipment -
Electromagnetic
Ballast – Energy
standards and
labelling
requirements
Class “H” PNS 13:1999 ➝ - UL 198B:1995
Fuses
Electric wires PNS 35-1:2004 ➝ IEC 227-1:1993 NEQ Philippine electrical system configuration
and cables –
Thermoplastic-
insulated
copper wires &
cables rated
600 volts – Part
1: General
specifications
Tungsten PNS 38-1:1995 ➝ IEC 432-1:1993 IDT
filament lamps And. 01:1995
for domestic
and similar
general lighting
purposes -
Safety

71 of 120
Version 12 as of May 2010

Tungsten PNS 38-2:1995 ➝ IEC 64:1993 IDT

filament lamps
for domestic
and similar
general lighting
purposes -
Performance
Lamp holders PNS 42:1997 ➝ IEC 400:1996 IDT
and starter
holders for
tubular
fluorescent
lamps
Glow-starters PNS 45:1997 ➝ IEC 155:1993 Amd. IDT
for fluorescent Amd. 01:1997 01:1995
lamps
Fuseholders – PNS 56:1996 ➝ - ANSI/UL 512:1992
specifications
Snap switches PNS 57:1996 ➝ - UL 20:1995
for general use
PVC tapes for PNS 79:1992 ➝ IEC 454-3 NEQ Note: IEC was already adopted subject to
electrical implementation.
insulation
Edison Screw PNS 80:1997 ➝ IEC 238:1996 IDT
lamp holders
Knife switches PNS 118:1992 ➝ - -
AC supplied PNS 135-1:1997 ➝ IEC 928:1995-02 IDT
electronic
ballast for
tubular
fluorescent
lamps - Safety
AC supplied PNS 135-2:1993 ➝ IEC 929:1990 Amd. IDT
electronic Amd. 01 & 02: 01:1994 & 02:1996
ballast for 1997
tubular
fluorescent
lamps -
Performance
Polyvinyl PNS 163:1994 ➝ IEC 227 NEQ Note: PNS does not include IEC sizes for oval
chloride sheathed chords
insulated
flexible cords

72 of 120
Version 12 as of May 2010

Lighting sets PNS 189:2000 ➝ - BS 4647

using miniature
and sub-
miniature lamps
for decorative
purposes for
indoor use
Safety of PNS IEC 60335- ➝ IEC 60335-2-24: MOD All products covered shall not use CFC
household and 2-24: 2001 2000 refrigerants as stated in Amd. 1.
similar Amd. 01: 2003
electrical
appliances Part
2-24: Particular
requirements
for refrigerating
appliances, ice
cream
appliances and
ice makers
Safety PNS 254-1:1994 ➝ IEC 60335-2-3:1993 IDT
requirements Amd. 01:2000 Amd. 01:1999
for electric irons
Safety PNS 255:1996 ➝ IEC 335-2-15:1995 IDT
requirements
for appliances
for heating
liquids
Audio, video & PNS 256:1999 ➝ IEC 60065:1998 IDT
similar Amd. 01:2003
electronic
apparatus -
Safety
Safety PNS 272:1996 ➝ IEC-335-2-9:1993 IDT
requirements
for toasters,
grills, roasters
and similar
appliances
Non-ducted air PNS 396-1:1998 ➝ - -
conditioners –
Energy
Efficiency Ratio
(EER) and
labelling
requirements

73 of 120
Version 12 as of May 2010

Refrigerators PNS 396-2:1997 ➝ - -

and freezers – Amd.01:2000
Energy
Efficiency
Factor (EEF)
and labelling
requirements
Moulded case PNS 519:1991 ➝ - AS 2184:1984
circuit breakers UL 489
Self-ballasted PNS 603-1:1993 ➝ IEC 60968:1988 IDT
lamps for Amd. 01:2001 Amd.01:1991
general lighting Amd. 02:1999
services –
Safety
Self-ballasted PNS 603-2:1993 ➝ IEC 969:1988 IDT
lamps for Amd.01:2001
general lighting
services –
Performance
General PNS 1079:1994 ➝ IEC 335-1:1991 IDT
Requirements Amd. 01:1994
for safety of
household and
similar
electrical
appliances
Safety PNS 1169:1993 ➝ IEC-335-2-2:1993 IDT
requirements
for vacuum
cleaners and
water suction
cleaning
appliances
Safety PNS 1244:1994 ➝ IEC-335-2-14:1984 IDT
requirements
for kitchen
machines
Single-capped PNS 1261:1995 ➝ IEC 901:1992 IDT
fluorescent
lamps -
Performance
Luminaires PNS 1328:1996 ➝ IEC 598-1:1992 IDT

74 of 120
Version 12 as of May 2010

General PNS1485-1:1996 ➝ IEC 669-1:1993/

requirements Amd. 01 & Amd. 01:1994 Amd.
for switches for 02:1996 02:1995
household and
similar fixed-
electrical
installations
Plugs and PNS 1486-1:1996 ➝ IEC 884-1:1994 IDT
socket outlets
for households
and similar
purposes –
General
requirements
Safety PNS 1558:1997 ➝ IEC-335-2-21:1989 IDT
requirements Amd. 01,02,03: Amd. 01,02:1990
for storage 1997 Amd. 03:1992
water heaters
Plugs and PNS 1572:1997 ➝ IEC 83:1975 MOD Put another column for configuration of plugs
socket outlets to meet Philippine condition.
for domestic
and similar
general use
standards
Low voltage PNS 1573-2:1997 ➝ IEC 947-2:1995 IDT
switchgear and
control gear –
Part 2: Circuit
breakers
Safety PNS 1680:1998 ➝ IEC 335-2-4:1993 IDT
requirements
for spin
extractors
Boxes for rigid PNS 1829:1999 ➝ JISC 8336:1991
metal conduits
Safety PNS IEC 60335- ➝ IEC 60335-2-6:1997 IDT
requirements 2-6:2000 Amd.01:2000
for stationary Amd.01:2001
cooking ranges,
hobs, ovens
and similar
appliances
Safety PNS IEC 60335- ➝ IEC 60335-2-7:2000 MOD Class 01appliance is allowed.
requirements 2-7:2001
for washing
machines

75 of 120
Version 12 as of May 2010

Safety PNS IEC 60335- ➝ IEC 60335-2- IDT

requirements 2-25:2000 25:1996
for microwave
ovens
Safety PNS IEC 60335- ➝ IEC 60335-2-31: IDT
requirements 2-31:2000 1995
for range hoods
Safety PNS IEC 60335- ➝ IEC 60335-2- IDT
requirements 2-35:2000 35:1997
for
instantaneous
water heaters
Safety PNS IEC 335-2- ➝ IEC 60335-2-40: IDT All products covered shall not use CFC
requirements 40:2000 1995 refrigerants as stated in Amd. 2.
for electrical
heat pumps air- Amd. 1: 2000
conditioners Amd. 2: 2003
and
dehumidifiers
Safety PNS IEC 60335- ➝ IEC 60335-2-74: IDT
requirements 2-74:2000 1994
for portable
immersion
heaters
Safety PNS IEC 60335- ➝ IEC 60335-2-80: IDT
requirements 2-80:2000 1997
for Fans
Double capped PNS IEC ➝ IEC 60081:1997 IDT
fluorescent 60081:2001
lamps -
Performance
Safety of power PNS IEC 61558- ➝ IEC 61558-1:1998
transformers, 1:2002
power supply
units and
similar devices

76 of 120
Version 12 as of May 2010

V. MODE OF REGULATION AND TYPES OF CONFORMITY ASSESSMENT REGIMES

COUNTRY TYPES OF MODE OF REGULATION

CONFORMITY
ASSESSMENT
REGIMES
PHILIPPINES Registration/Certification
Philippine Standard (PS) Quality and/or Safety Certification Mark Scheme

• These marks are awarded to domestic and foreign manufacturers that consistently comply with
quality management system standards. These are awarded after a thorough assessment of the
manufacturer based on ISO 9000 series standards. The products are also subjected to laboratory
testing to verify compliance with PNS. Even after the issuance of the license to use PS certification
marks, surveillance is regularly conducted.

Treatment of Imports

• Products covered by mandatory certification shall secure Import Commodity Clearance with BPS.
• Import shipment that meets product quality and safety requirements of the specific Philippine
National Standards is issued the Import Commodity Clearance Certificate.

77 of 120
Version 11 – as of May 2009

VI. FLOWCHART OF PHILIPPINES’ REGIME

PS Quality and/or Safety Certification Mark Scheme

Application

Application Review

Factory Audit
Quality System Audit Corrective
Product Audit/ Actions
In-plant Testing

NO
Complied
YES
Independent Testing

Audit Report & Test Result

Evaluation

NO
Complied
YES
License to use PS Quality or Safety
Mark Issued 78 of 120

Surveillance
Version 12 – as of May 2010
Import Commodity Clearance Scheme (ICC)

Application OPTION 1: Issuance of ICC

on Import
Evaluation shipment w/o
foreign test
Issuance of NO report
Certificate of Covered
YES
Issuance of Conditional Release

Conducts Inventory/inspection and

Testing (BPSTC/Accredited
L b t i )

Evaluation of Test Result

YES

Complied Re-testing
NO
YES NO
Issuance of ICC
Denial of ICC
application
END

79 of 120
Version 12 – as of May 2010

Import Commodity Clearance Scheme (ICC)

Application OPTION 2: Issuance of ICC

on Import
Evaluation shipment with
foreign test
Issuance of NO report
Certificate of Covered
YES
Issuance of Conditional Release

Evaluation of Test Report

OPTION 1 apply
Complied
NO
YES
Issuance of ICC

END

80 of 120
Version 12 – as of May 2010

Import Commodity Clearance Scheme (ICC)

OPTION 3: Issuance of ICC

Application on Import
shipment with
PS Safety/Quality
Certification Mark
Evaluation

Issuance of Certificate of Exemption

END

81 of 120
Version 12 – as of May 2010

VII. MAINS VOLTAGE, FREQUENCY AND MAINS PLUG CONFIGURATION

Country Mains Mains Applicable Mains Plug Configuration

Voltage and Frequency Legislation Domestic Please tick Relevant Extent of Diagram of Mains Plug Configuration-
Tolerance and Standard box if International Alignment
Tolerance mandatory Standard
Philippines 230V 60 +/- 1Hz NA PNS ➝ IEC MOD Put another column for configuration of plugs to meet
+/- 10% 1572:1997 83:1975 Philippine condition.

VIII CONTACT PERSON

Country Contact Person and Address

PHILIPPINES JESUS L. MOTOOMULL
Director, Bureau of Product Standards (BPS)
3F Trade and Industry Building
361 Sen. Gil J. Puyat Avenue
Makati City, Metro Manila
1200 Philippines

Tel. No. : +632 751-3123

Fax. No.: +632 751-4706
Email; bps@[Link]
Website: [Link]

82 of 120
Version 12 as of May 2010

PHILIPPINE QUALITY/SAFETY MARK LOGOS

ICC Mark Logo

PS Certification Mark Logo

CERTIFIED CERTIFIED
PRODUCT SAFETY PRODUCT QUALITY

Update of Singapore’s Regulatory Regime (version dated 23 Oct 2008) Page 83 of 120
For circulation to ASEAN Member States for information at the 6th JSC EEE meeting to be held in Bali on 6-7 Nov 2008
Version 12 as of May 2010
Annex 1

Update of Singapore’s Regulatory Regime (version dated 23 Oct 2008) Page 84 of 120
For circulation to ASEAN Member States for information at the 6th JSC EEE meeting to be held in Bali on 6-7 Nov 2008
Version 12 as of May 2010

SINGAPORE

I. RATIONALE FOR REGULATION

COUNTRY RATIONALE FOR REGULATION

Singapore Consumer Protection.

II. REGULATION BODY

COUNTRY REGULATORY BODY

Singapore Standards, Productivity and Innovation Board (or SPRING Singapore in short)

III. LEGISLATIVE FRAMEWORK

COUNTRY LEGISLATIVE FRAMEWORK

Singapore Consumer Protection (Safety Requirements) Regulations 2002* which is based on the Consumer
Protection (Trade Descriptions and Safety Requirements) Act (Chapter 53)
* Consumer Protection (Safety Requirements) Regulations 1991 has been revoked and replaced by
Regulations 2002.

Update of Singapore’s Regulatory Regime (version dated 23 Oct 2008) Page 85 of 120
For circulation to ASEAN Member States for information at the 6th JSC EEE meeting to be held in Bali on 6-7 Nov 2008
Version 12 as of May 2010

IV. MANDATORY STANDARDS

-
2-Adaptor - IEC 61558-2-6: 1997
or
IEC 61558-2-17: 1997
(applicable for electrical
appliances)
-
- IEC 60065: 1998
or
IEC 60065: 2001
(applicable for electronic
appliances)

- IEC 60950:1999 -
or
IEC 60950-1: 2001
(applicable for computer /
telephonic appliances)

IEC 60335-2-8: 2002 -

(applicable for battery
chargers)

IEC 60335-2-29: 2002

(applicable for battery
chargers)

3-Any other audio - IEC 60065: 1998 -

products or
IEC 60065: 2001

Update of Singapore’s Regulatory Regime (version dated 23 Oct 2008) Page 86 of 120
For circulation to ASEAN Member States for information at the 6th JSC EEE meeting to be held in Bali on 6-7 Nov 2008
Version 12 as of May 2010

5-Coffee maker, - IEC 60335-2-15: 1995 -

slow cooker, or
steam boat and IEC 60335-2-15: 2002
similar appliances
Singapore 6-Decorative - IEC 60598-2-20: 1998 -
lighting fixture or
IEC 60598-2-20: 2002

7-Hairdryer - IEC 60335-2-23: 1996 -

or
IEC 60335-2-23: 2003

8-Home computer - IEC 60950 : 1999 -

system (inclusive or
of monitor, printer, IEC 60950-1: 2001
speaker and other
mains operated
accessories)

9-High-fidelity set - IEC 60065: 1998 -

or
IEC 60065: 2001

-
10-Iron - IEC 60335-2-3: 1993
or
IEC 60335-2-3: 2002

-
11-Immersion - IEC 60335-2-74: 1994
water heater or
IEC 60335-2-74: 2002

Update of Singapore’s Regulatory Regime (version dated 23 Oct 2008) Page 87 of 120
For circulation to ASEAN Member States for information at the 6th JSC EEE meeting to be held in Bali on 6-7 Nov 2008
Version 12 as of May 2010

13-Laser disc set - IEC 60065: 1998 -

or
IEC 60065: 2001

Singapore 14-Microwave - IEC 60335-2-25: 1996 -

Oven or
IEC 60335-2-25: 2002

-
15-Mobile split air - IEC 60335-2-40: 1995
conditioner or
IEC 60335-2-40: 2002

16-Mixer, blender, - IEC 60335-2-14: 1994 -

mincer and similar or
appliances IEC 60335-2-14: 2002

17-Refrigerator - IEC 60335-2-24: 2000 -

or
IEC 60335-2-24: 2002

18-Rice cooker IEC 60335-2-15: 1995 -

or
IEC 60335-2-15: 2002

19-Room Air - IEC 60335-2-40: 1995 -

Conditioner or
IEC 60335-2-40: 2002

Update of Singapore’s Regulatory Regime (version dated 23 Oct 2008) Page 88 of 120
For circulation to ASEAN Member States for information at the 6th JSC EEE meeting to be held in Bali on 6-7 Nov 2008
Version 12 as of May 2010

21-Table or - IEC 60335-2-80: 1997 -

standing fan or
IEC 60335-2-80: 2002

Singapore 22-Table - IEC 60598-2-4: 1997 -

lamp/standing
lamp

23-Toaster, grill, - IEC 60335-2-9: 1993 -

roaster, hot plate or
and similar IEC 60335-2-9: 2002
appliances (applicable for toaster, hot
plate (including induction
type), grill, oven and similar
appliances)

IEC 60335-2-13: 1993 with

A1 and/or A2
or
IEC 60335-2-13: 2002
(applicable for deep fryer,
electric wok and similar
appliances)

24-Video cassette - IEC 60065: 1998 -

recorder or
IEC 60065: 2001

Update of Singapore’s Regulatory Regime (version dated 23 Oct 2008) Page 89 of 120
For circulation to ASEAN Member States for information at the 6th JSC EEE meeting to be held in Bali on 6-7 Nov 2008
Version 12 as of May 2010

26-Washing - IEC 60335-2-7: 1993 -

machine or
IEC 60335-2-7: 2002

27-Wall fan/ceiling - IEC 60335-2-80: 1997 -

fan or
IEC 60335-2-80: 2002
-

SS 360: 1992 (sub-clauses √

5.7 & 5.8 only)
(applicable for
ceiling fan)

28-3-pin SS 145: Part 1: 1997 √ - based on BS 1363:Part 1

rectangular type :1995
13-Amp Plug
Singapore
29-Fuses (≤13A) SS 167: 1977 √ - based on BS 1362 :1973
for use in plug

30-3-pin round SS 472: 1999 √ - based on BS 546: 1950

type 15-amp plug
31-Multi-way SS 246: 1996 √ - based on BS 1363:Part 3
Adaptors :1995
32-3-pin Portable SS 145: Part 2: 1997 √ - based on BS 1363 Part 2:
Socket-outlet 1995

33-Portable Cable SS 307: 1996 √ - based on IEC 1242: 1995

Reels
Or SS 145: Part 1 (13A plug) IEC 61242: 1995
& SS 145: Part 2 (13A
socket-outlet)

Update of Singapore’s Regulatory Regime (version dated 23 Oct 2008) Page 90 of 120
For circulation to ASEAN Member States for information at the 6th JSC EEE meeting to be held in Bali on 6-7 Nov 2008
Version 12 as of May 2010

STANDARDS
Total Product type
Country Domestic Standards Please tick Relevant International Extent of Alignment State reason if MOD
Product or grouping box if
mandatory Standards
34-Instantaneous a) Bare heating elements are
Electric Water SS 146: Part 2: 5: 1999 IEC 60335-2-35 :1997 not allowed
Heater or √ & MOD b) Water temperature from 15°
SS 146: Part 2: 5: 2007 IEC 60335-2-35: 2002 to 25°C
c) Water heater shall be at
least IPX4
35-Mains a) Bare heating elements are not
Pressure Electric allowed
Storage Water b) Water heater shall be Class I
Heater SS 146:Part [Link] 1999 IEC 60335-2-21: 1997 c) Additional markings
√ MOD requirements
or &
SS 146: Part 2: 8: 2007 IEC 60335-2-35: 2002 d) To incorporate pressure relief
valve, thermostat and thermal
cut-out
e) Thermal cut-out shall provide
all-pole disconnection

36- Residual Incorporated national wiring

SS 97: Part 1: 2000 √ code requirement.
Current Circuit IEC 61008-1: 1996 MOD
Breaker (RCCB)
37-3-pin 13-amp -
√ based on BS 1363: Part 2:
socket-outlet SS 145: Part 2: 1997 -
1995

38-3-pin round -
SS 472: 1999 √
type 15-amp - based on BS 546: 1950
socket-outlet
39- Domestic -
electric wall switch SS 227: Part 1: 2000 IEC 60669-1: 1998 IDT

40- Ballast for IEC 61347-2-8: 2000 IDT

SS 490: Part 2: 8: 2001 (magnetic ballast)
tubular fluorescent (magnetic ballast)
lamp
SS 490: Part 2: 3: 2002 IEC 61347-2-3: 2000 IDT
(electronic ballast) (electronic ballast)

Update of Singapore’s Regulatory Regime (version dated 23 Oct 2008) Page 91 of 120
For circulation to ASEAN Member States for information at the 6th JSC EEE meeting to be held in Bali on 6-7 Nov 2008
Version 12 as of May 2010

V. MODE OF REGULATION AND TYPES OF CONFORMITY ASSESSMENT REGIMES

COUNTRY TYPES OF CON- MODE OF REGULATION

FORMITY ASSESS-
MENT REGIMES
Singapore Registration The regulatory regime consists of two phases – pre-market approval and post-market
surveillance.

There is a regulator intervention prior to the entry of the regulated products into the market. The
controlled goods have to go through a structured process of approval, which starts with testing
and ends with labelling. Please see Section VI - Flowchart of Singapore's Regime.

After entry into the market, SPRING Singapore conducts regular visits to shops and retail outlets
to ensure that only registered controlled goods are displayed or offered for sale.

Treatment of Controlled Goods

Registration of controlled goods is based on certification by designated Conformity Assessment

Bodies.

Update of Singapore’s Regulatory Regime (version dated 23 Oct 2008) Page 92 of 120
For circulation to ASEAN Member States for information at the 6th JSC EEE meeting to be held in Bali on 6-7 Nov 2008
Version 12 as of May 2010

VI. FLOWCHART OF MEMBER COUNTRIES’ REGIME

Supplier applies to SPRING Singapore to be a Registered Supplier

Registered Supplier submits Controlled Goods to a CAB (Local) or CAB

(Foreign-MRA) for Certification to SPRING Singapore safety standards
requirements

CAB (Local) or CAB (Foreign-MRA) issues COC (valid for 3 years) to

Registered Supplier after certifying the Controlled Goods

Registered Supplier submits COC to SPRING Singapore for registration of the

certified Controlled Goods

SPRING Singapore issues acknowledgement to Registered Supplier and lists

the controlled goods in the Register

Registered Supplier affixes SAFETY Mark and commences supply of registered

controlled goods

The SAFETY Mark comprises of a safety logo enclosed in a square on the left
and the word “SAFETY MARK” enclosed in a rectangle on the right. Below the
logo is an unique certification number traceable to the registrant. The colour
used is Pantone 287C Blue Colour.

Registered Supplier submits the registered controlled goods to the CAB for re-
certification before COC expires

Update of Singapore’s Regulatory Regime (version dated 23 Oct 2008)

th
For circulation to ASEAN Member States for information at the 6 JSC EEE meeting to be held in Bali on 6-7 Nov
2008
Version 12 as of May 2010

VII. MAINS VOLTAGE, FREQUENCY AND MAINS PLUG CONFIGURATION

Country Mains Mains Applicable Mains Plug Configuration

Voltage Frequency Legislation Domestic Please tick Relevant Extent of Diagram of Mains Plug Configuration-
and and Standard box if International Alignment
Tolerance Tolerance mandatory Standard -
Singapore 230 volts 50 Hz NA SS 145 for 3-pin Not applicable -
single ± 1% rectangular type
phase 13-amp plug
tolerance SS 472 for 3-pin
±6% round type 15-amp
plug

400 volts 50 Hz NA - - -
three phase ± 1%
tolerance
±6%

VIII. CONTACT PERSON

Country Contact Person and Address

Singapore Dennis Chew

SPRING Singapore
2 Bukit Merah Central
5th Floor Podium Block
Singapore 159835
Contact no: (65) 6279 1824
Fax no: (65) 6278 6993
Email: dennis_chew@[Link]
Website: [Link]/safety

Update of Singapore’s Regulatory Regime (version dated 23 Oct 2008) Page 94 of 120
For circulation to ASEAN Member States for information at the 6th JSC EEE meeting to be held in Bali on 6-7 Nov 2008
Version 12 as of May 2010

Additional information from SINGAPORE:

SINGAPORE

I. RATIONALE FOR REGULATION

COUNTRY RATIONALE FOR REGULATION

Singapore To provide energy efficiency information of clothes dryers in Annex A to consumers through energy
labels, allowing the consumer to take energy efficiency into consideration while making purchasing
decisions.

II. REGULATION BODY

COUNTRY REGULATORY BODY

Singapore National Environment Agency (NEA)

III. LEGISLATIVE FRAMEWORK

COUNTRY LEGISLATIVE FRAMEWORK

Singapore Environmental Protection and Management (Registrable Goods) Order

Environmental Protection and Management (Energy Conservation) Regulations

Update of Singapore’s Regulatory Regime (version dated 23 Oct 2008) Page 95 of 120
For circulation to ASEAN Member States for information at the 6th JSC EEE meeting to be held in Bali on 6-7 Nov 2008
Version 12 as of May 2010

IV. MANDATORY STANDARDS

STANDARDS
Product
Total Domestic Please Relevant
Country type or tick box if Extent of State reason if MOD
Product Standards International
grouping mandator Alignment
y Standards
Singapore Clothes All N/A √ IEC 61121: 2005
Dryer

V. MODE OF REGULATION AND TYPES OF CONFORMITY ASSESSMENT REGIMES

COUNTRY TYPES OF CON- MODE OF REGULATION

FORMITY ASSESS-
MENT REGIMES
Singapore Self-declaration Registrable clothes dryers listed in Annex A have to be registered with NEA and labelled
before they are supplied in Singapore.

Update of Singapore’s Regulatory Regime (version dated 23 Oct 2008) Page 96 of 120
For circulation to ASEAN Member States for information at the 6th JSC EEE meeting to be held in Bali on 6-7 Nov 2008
Version 12 as of May 2010

VI. FLOWCHART OF MEMBER COUNTRIES’ REGIME

Importer or manufacturer of registrable clothes dryers

listed in Annex A applies to NEA for registration as a
registered supplier

Registered supplier applies to NEA for registration of

registrable clothes dryer and submits a test report
prepared in accordance with the prescribed test
standard

NEA issues Certificate of Registration (valid for 3

years) to successful application

Registered supplier provides energy efficiency

information of registered clothes dryer via a label in
the manner prescribed in the regulations

Update of Singapore’s Regulatory Regime (version dated 23 Oct 2008) Page 97 of 120
For circulation to ASEAN Member States for information at the 6th JSC EEE meeting to be held in Bali on 6-7 Nov 2008
Version 12 as of May 2010

VII. MAINS VOLTAGE, FREQUENCY AND MAINS PLUG CONFIGURATION

Country Mains Mains Applicable Mains Plug Configuration

Voltage Frequency Legislation Domestic Please tick Relevant Extent of Diagram of Mains Plug Configuration-
and and Standard box if International Alignment
Tolerance Tolerance mandatory Standard -
N/A

VIII. CONTACT PERSON

Country Contact Person and Address

Singapore Tng Mei Ling

40 Scotts Road
#11-00 Environment Building
Singapore 228231
Telephone no.: (65) 6731-9908
Fax no.: (65) 6734-6956
Email: tng_mei_ling@[Link]

Update of Singapore’s Regulatory Regime (version dated 23 Oct 2008) Page 98 of 120
For circulation to ASEAN Member States for information at the 6th JSC EEE meeting to be held in Bali on 6-7 Nov 2008
Version 12 as of May 2010

ANNEX A

No HS Code Commodity
1. HS 8451 20XX Single-phase clothes dryer namely an assembly consisting of a rotating drum, in which textile
HS 8451 2100 material is dried by tumbling, and a heating device, which electrically heats the air used for drying the
textile material in the rotating drum. The clothes dryer (not being second-hand goods) shall have a
rated capacity of 10 kilograms or lower.

Update of Singapore’s Regulatory Regime (version dated 23 Oct 2008) Page 99 of 120
For circulation to ASEAN Member States for information at the 6th JSC EEE meeting to be held in Bali on 6-7 Nov 2008
Version 12 as of May 2010

THAILAND
I. RATIONALE FOR REGULATION

COUNTRY RATIONALE FOR REGULATION

Thailand Consumer Protection.

II. REGULATION BODY

COUNTRY REGULATORY BODY

Thailand Thai Industrial Standards Institute (TISI) under the Ministry of Industry.

III. LEGISLATIVE FRAMEWORK

COUNTRY LEGISLATIVE FRAMEWORK

Thailand Industrial Product Standards Act. (1968)

Update of Singapore’s Regulatory Regime (version dated 23 Oct 2008) Page 100 of 120
For circulation to ASEAN Member States for information at the 6th JSC EEE meeting to be held in Bali on 6-7 Nov 2008
Version 12 as of May 2010

IV. MANDATORY STANDARDS

REVISED MATRIX ON MANDATORY STANDARDS FOR THAILAND (AS OF MAY 6, 2008)
Country Total STANDARDS
Prod
Product type or grouping Please tick Relevant
uct Extent of
Domestic Standards box if International State reason if MOD
Alignment
mandatory Standards
Thailand 1 Incandescent lamps TIS 4 Part 1-2529 √ IEC 60064 (1993) NEQ -
(1986) IEC 60432-1(1999)
Thailand 2 Low-voltage distribution link fuses TIS 10-2529 (1986) √ IEC 60269-1(1998), NEQ -
IEC 60269-3(1987)
Thailand 3 PVC insulated Copper cables TIS 11-2531 (1988) √ IEC 60227-1 NEQ -
(1993),
Am.1(1995),
Am.2(1998)
IEC 60227-2 (1997)
Thailand 4 Ballast for fluorescent lamps TIS 23-2521 (1978) √ IEC 60920 (1990), NEQ -
Am.1(1993),
Am.2(1995)
IEC 60921(1988),
Am.1(1990),
Am.2(1994)
Thailand 5 Starters for fluorescent lamps TIS 183-2547 (1985) √ IEC IDT -
60155(1993),
Am.1(1995)
Thailand 6 PVC insulated aluminium cables TIS 293-2541 (1998) √ - - -
Thailand 7 Lampholders for tubular fluorescent TIS 344-2549 (2006) √ IEC 60400 (1999) NEQ -
lamps and starterholders

Update of Singapore’s Regulatory Regime (version dated 23 Oct 2008) Page 101 of 120
For circulation to ASEAN Member States for information at the 6th JSC EEE meeting to be held in Bali on 6-7 Nov 2008
Version 12 as of May 2010

Country Total STANDARDS

Prod
Product type or grouping Please tick Relevant
uct Extent of
Domestic Standards box if International State reason if MOD
Alignment
mandatory Standards
Thailand 8 Electric irons TIS 366-2547 (2004), √ IEC 60335-2-3 MOD See TIS 1375-2547
TIS 1375-2547 - (2002-03) MOD TIS 1375-2547
(2004) IEC 60335-1, Am.1
Subclause 24.4
(2004)
In the first paragraph,
add words “TIS 166,
TIS 1234” before word
“IEC 60083 or IEC
60906-1”.

Subclause 25.25
In the last sentence of
the first paragraph,
replace words “IEC
60083” with “TIS 166
and TIS 1234”
Thailand 9 Electrical Switches TIS 824-2551 (2008) √ IEC 60669- IDT -
1(1983)

Thailand 10 Electric stoves; open type heating TIS 870-2532 (1989) √ IEC60335-2-9, NEQ -
elements: safety requirements Am.1 (2005-06)
Thailand 11 AC electric fans : safety TIS 934-2533 (1990) √ IEC 60335-2- 80 NEQ -
requirements (1997)
Thailand 12 Fluorescent lamps : safety TIS 956-2533 √ IEC 60081 (1997) NEQ -
requirements (1990)

Update of Singapore’s Regulatory Regime (version dated 23 Oct 2008) Page 102 of 120
For circulation to ASEAN Member States for information at the 6th JSC EEE meeting to be held in Bali on 6-7 Nov 2008
Version 12 as of May 2010

Country Total STANDARDS

Prod
Product type or grouping Please tick Relevant
uct Extent of
Domestic Standards box if International State reason if MOD
Alignment
mandatory Standards
Thailand 13 Electric rice-cookers : safety TIS 1039-2547 √ IEC 60335-2-15 MOD See TIS 1375-2547
requirements (2004) - (2002-07) MOD TIS 1375-2547
TIS 1375-2547 IEC 60335-1, Am.1
Subclause 24.4
(2004) (2004)
In the first paragraph,
add words “TIS 166,
TIS 1234” before word
“IEC 60083 or IEC
60906-1”.

Subclause 25.25
In the last sentence of
the first paragraph,
replace words “IEC
60083” with “TIS 166
and TIS 1234”
Thailand 14 Mains operated electronic and TIS 1195-2536 √ IEC 60065 (1985) MOD TIS 1195-2536
related apparatus for household (1993) Sub-clause 9.1.1
and similar general use : safety
the current measured
requirements
shall not exceed 0.3
mA (peak)
Thailand 15 Uninterruptible power system TIS 1291-2545 √ - - -
(2002)

Update of Singapore’s Regulatory Regime (version dated 23 Oct 2008) Page 103 of 120
For circulation to ASEAN Member States for information at the 6th JSC EEE meeting to be held in Bali on 6-7 Nov 2008
Version 12 as of May 2010

Country Total STANDARDS

Prod
Product type or grouping Please tick Relevant
uct Extent of
Domestic Standards box if International State reason if MOD
Alignment
mandatory Standards
Thailand 16 Tumbler dryers : safety TIS 1389-2539 √ IEC 60335-2- MOD TIS 1389-2539
requirements (1996) 11(1993) Sub-clause 1.1
Scope excluding rated
voltage 480 V.
Sub-clause [Link]
temp. rise of the
accessible front surface
made of glass, ceramic
and plastic parts.
Sub-clause 4.14.6
minimum cross-
sectional area of
conductors of supply
cords
Sub-clause 4.15.3
nominal cross-sectional
area of conductors.
Sub-clause 4.18.2
requirements on
creepage distance,
clearance and distance
through insulation.

Update of Singapore’s Regulatory Regime (version dated 23 Oct 2008) Page 104 of 120
For circulation to ASEAN Member States for information at the 6th JSC EEE meeting to be held in Bali on 6-7 Nov 2008
Version 12 as of May 2010

Country Total STANDARDS

Prod
Product type or grouping Please tick Relevant
uct Extent of
Domestic Standards box if International State reason if MOD
Alignment
mandatory Standards
Thailand 17 Washing machines : safety TIS 1463-2540 √ IEC 60335-2-7 MOD TIS 1463-2540
requirements (1997) (1993) Sub-clause 2.10
water temperature
45+5C.
Sub-clause 4.18
requirements on
creepage distance,
clearance and distance
through insulation.
Sub-clause 7.1
ambient temperature
27+2C.
Annex B.5
ambient temperature
27+2C, humidity
65+5%.

Update of Singapore’s Regulatory Regime (version dated 23 Oct 2008) Page 105 of 120
For circulation to ASEAN Member States for information at the 6th JSC EEE meeting to be held in Bali on 6-7 Nov 2008
Version 12 as of May 2010

Country Total STANDARDS

Prod
Product type or grouping Please tick Relevant
uct Extent of
Domestic Standards box if International State reason if MOD
Alignment
mandatory Standards
Thailand 18 Electric fryers: safety requirements TIS 1509-2547 √ IEC 60335-2-13 MOD TIS 1509-2547
(2004) - (2002-10) MOD
TIS 1375-2547 Clause 1
(2004) IEC 60335-2-15 Scope of the Standard
(2002-07) cover fryers, frying
pans and similar
IEC 60335-1, Am.1 appliances as defined
(2004) in Subclause
3.101,3.102 and 3.103

Remark 102
Scope of the Standard
does not cover high
frequency-heating
electric fryers.
Subclause 3.101
Definition of electric
fryers.
Subclause 3.102
Definition of electric
deep-fryers.
Subclause 3.103
Definition of electric
frying pans.

Clause 6

Classified electric
fryers into 3 classes;
0I, I and II.

Update of Singapore’s Regulatory Regime (version dated 23 Oct 2008) Page 106 of 120
For circulation to ASEAN Member States for information at the 6th JSC EEE meeting to be held in Bali on 6-7 Nov 2008
Version 12 as of May 2010

Country Total STANDARDS

Prod
Product type or grouping Please tick Relevant
uct Extent of
Domestic Standards box if International State reason if MOD
Alignment
mandatory Standards

see TIS 1375-2547

TIS 1375-2547
Subclause 24.4
In the first paragraph,
add words “TIS 166,
TIS 1234” before word
“IEC 60083 or IEC
60906-1”.

Subclause 25.25
In the last sentence of
the first paragraph,
replace words “IEC
60083” with “TIS 166
and TIS 1234”
Thailand 19 Instantaneous water heaters TIS 1693-2547 √ IEC 60335-2-35 MOD See TIS 1375-2547
:safety requirements (2004) - (2002-10) MOD TIS 1375-2547
TIS 1375-2547 IEC 60335-1, Am.1
Subclause 24.4
(2004) (2004)
In the first paragraph,
add words “TIS 166,
TIS 1234” before word
“IEC 60083 or IEC
60906-1”.

Subclause 25.25
In the last sentence of
the first paragraph,
replace words “IEC
60083” with “TIS 166
and TIS 1234”

Update of Singapore’s Regulatory Regime (version dated 23 Oct 2008) Page 107 of 120
For circulation to ASEAN Member States for information at the 6th JSC EEE meeting to be held in Bali on 6-7 Nov 2008
Version 12 as of May 2010

Country Total STANDARDS

Prod
Product type or grouping Please tick Relevant
uct Extent of
Domestic Standards box if International State reason if MOD
Alignment
mandatory Standards
Thailand 20 Lighting and similar equipment TIS 1955-2542 √ CISPR 15 (1999) IDT -
: radio disturbance limits (1999)
Thailand 21 Electric thermo pots TIS 2062-2543 √ IEC 60335-2-15 MOD TIS 2062-2543
(2000) (1995) Contents of the
standard deals with
thermo pots only.
Thailand 22 Room Air Conditioners TIS 2134-2545(2002) √ - - -
Environment Requirement
: Energy Efficiency
Thailand 23 Household refrigerators : TIS 2186-2547 √
environmental requirements : (2004)
energy efficiency

Update of Singapore’s Regulatory Regime (version dated 23 Oct 2008) Page 108 of 120
For circulation to ASEAN Member States for information at the 6th JSC EEE meeting to be held in Bali on 6-7 Nov 2008
Version 12 as of May 2010

Country Total STANDARDS

Prod
Product type or grouping Please tick Relevant
uct Extent of
Domestic Standards box if International State reason if MOD
Alignment
mandatory Standards
Thailand 24 Household refrigerators : safety TIS 2214-2548 √ IEC 60335-2-24 MOD TIS 2214-2548
requirements (2005) (2002) Subclause 5.7
TIS 1375-2547 IEC 60335-1, Am.1 Addition
(2004) (2004) “Appliances used in
Thailand are testes at
the ambient
temperature for
appliances used in
warm damp equable
climates”
Subclsuse 6.1
Addition
“Appliances used in
Thailand shall be class
OI, class I class II and
Class III”
see TIS 1375-2547
TIS 1375-2547
Subclause 24.4
In the first paragraph,
add words “TIS 166,
TIS 1234” before word
“IEC 60083 or IEC
60906-1”.

Subclause 25.25
In the last sentence of
the first paragraph,
replace words “IEC
60083” with “TIS 166
and TIS 1234”

Update of Singapore’s Regulatory Regime (version dated 23 Oct 2008) Page 109 of 120
For circulation to ASEAN Member States for information at the 6th JSC EEE meeting to be held in Bali on 6-7 Nov 2008
Version 12 as of May 2010

Country Total STANDARDS

Prod
Product type or grouping Please tick Relevant
uct Extent of
Domestic Standards box if International State reason if MOD
Alignment
mandatory Standards
Thailand 25 Secondary cells and batteries TIS 2217-2548 √ IEC 62133 Ed.1.0 IDT
containing alkaline or other non- (2005) (2002)
acid electrolytes - safety
requirements for portable sealed
secondary cells, and for batteries
made from them, for use in portable
applications
Thailand 26 Plugs and socket-outlets for TIS 166-2549(2006) √ IEC 60884-1(2002) MOD -The surrounding
household and similar purposes: temperarture not
Plugs and socket-outlets with rated exceeding 40 ° C
∗ - clause 9.2 When
voltage not exceeding 250 V
testing elastromeric
material, the ambient
temperature is set at
40±2 ° C
- clause 10.3 test is
made at 40±2 ° C
- clause 16.3 the
temperature in humidity
cabinet is set at any
convenient value 25 ° C
between 35 ° C
Thailand 27 Appliances for skin or hair care: TIS 1985-2549(2006) √ IEC 60335-2-23 MOD Editorial modification
∗∗ for systematic
Safety requirements reference to Thai
standard number.

∗
Effective on March 3, 2008
∗∗
Effective on July 14, 2008
Update of Singapore’s Regulatory Regime (version dated 23 Oct 2008) Page 110 of 120
For circulation to ASEAN Member States for information at the 6th JSC EEE meeting to be held in Bali on 6-7 Nov 2008
Version 12 as of May 2010

V. MODE OF REGULATION AND TYPES OF CONFORMITY ASSESSMENT REGIMES

COUNTRY TYPES OF CON- MODE OF REGULATION

FORMITY ASSESS-
MENT REGIMES
Thailand Certification Product Certification System of TISI consists of two phases:
1. License Granting
Granting a license is based on:
1.1 The results of tests which are conducted on products in accordance with the application
standards.
Consideration on this matter may be:
(1) Acceptation of testing results, or
(2) Product testing by designated laboratories, or
(3) Product testing by testing at manufacturer’s premises, or
(4) Product testing by supervised manufacturer’s testing.
1.2 The results of manufacturer’s quality control system assessment according to specified
conditions.

Consideration on this matter may be:

(1) Acceptation of quality system certificates, or
(2) Factory visit for quality control system assessment, or
(3) Manufacturer’s quality control system assessment on technical file of factory.

2. Surveillance
After granting a license, the licensee will be followed up by:
2.1 Product sampling from factories for testing,
2.2 Product sampling from market for testing,
2.3 Product sampling for testing each import,
2.4 Factory visit for audit.

Update of Singapore’s Regulatory Regime (version dated 23 Oct 2008) Page 111 of 120
For circulation to ASEAN Member States for information at the 6th JSC EEE meeting to be held in Bali on 6-7 Nov 2008
Version 12 as of May 2010

VI. FLOWCHART OF MEMBER COUNTRIES’ REGIME

Application for
Licences

Product Testing Manufacturer’s Quality Control

System Assessment

Pass Pass Fail

Licence
Granting Refuse of
Application

Surveillance

Update of Singapore’s Regulatory Regime (version dated 23 Oct 2008)

th
For circulation to ASEAN Member States for information at the 6 JSC EEE meeting to be held in Bali on 6-7 Nov
2008
Version 12 – as of May 2010

VII. MAINS VOLTAGE, FREQUENCY AND MAINS PLUG CONFIGURATION

Country Mains Mains Applicable Mains Plug Configuration

220 volts 1-
phase
2 wires with
earth
tolerance
±7 % and -
3%
Other Areas
220 volts 1-
phase
2 wires
tolerance
±10 %
Bangkok 50 Hz NA - - - -
Metropolita
n Area ± 1%

380 volts 3-
phase
4 wires
tolerance
±7 % and -
3%
Other Areas
380 volts 3-
phase
4 wires
tolerance
±10 %

Page 113 of 120

Version 12 – as of May 2010

VIII. CONTACT PERSON

Country Contact Person and Address

Director of Standards Bureau 2,
Thailand
Standards Bureau 2, Thai Industrial Standards Institute (TISI), Ministry of Industry,
Rama VI Street, Bangkok 10400 Thailand
Telephone (662) 202 3370, Telefax (662) 202 3474
E-mail : eemrabr2@[Link]

Page 114 of 120

Version 12 – as of May 2010

VIETNAM
I. RATIONALE FOR REGULATION

COUNTRY RATIONALE FOR REGULATION

Viet Nam Ensure Safety and consumer protection

II. REGULATION BODY

COUNTRY REGULATORY BODY

Viet Nam Directorate for Standards and Quality (STAMEQ)

III. LEGISLATIVE FRAMEWORK

COUNTRY LEGISLATIVE FRAMEWORK

Viet Nam Act on Product Quality ( 1999 )

Decree of Government on State Management Regulation for Goods and Products Quality (2004)*

Decision of the Ministry of Science and Technology on Safety Certification.

Decision of the Ministry of Science and Technology on State Inspection of Import-Export Products
Quality.

Note : * changes from previous version

Page 115 of 120

Version 12 – as of May 2010

IV. MANDATORY STANDARDS

Country Total Product STANDARDS REMARKS ON

Pleas
Product type or Domestic e tick
Relevant Extent of State reason if CHANGES
grouping Standards box if International Alignment MOD FROM
mand Standards PREVIOUS
atory
VERSION
Newer edition and Use
Viet Nam 4 - According [Link] Kettle TCVN5699-2-15:2000 √ IEC 60335-2-15:1995 IDT of amd IEC standards
to certification and other heating Adm.1:1999
Scheme apparatuses

No change
[Link] TCVN 5699-2-80:2000 IEC 60335-2-80:1997 IDT
Fans
√

Newer edition and Use

3. Electric TCVN 5699-2-3:2000 IEC 60335-2-3:1993 IDT of amd EC standards
Iron
√ Adm.1:1999

No change
4. Electric TCVN 5699-2-23:2000 IEC 60335-2-23:1996 IDT
Hairdryers
√

14 - 1. Electric Fan TCVN 5699-1:2004 √ IEC 60335-1:2001 IDT Newer edition of the std
According to TCVN 5699-2-80:1997 IEC 60335-2-80:1997 IDT
import, export 2. Electric TCVN 5699-1:2004 √ IEC 60335-1:2001 I Newer edition and use
certification immersion sticks TCVN 5699-2-15:2000 IEC 60335-2-15:1995 IDT of amd IEC std
Scheme Adm.1:1999
3. Storage Water TCVN 5699-1:2004 √ IEC 60335-1:2001 I Newer edition and use
Heaters TCVN 5699-2-21:2001 IEC 60335-2-21:1989 IDT of amd IEC std
Adm.1: 1990;
Adm.2:1990;
Adm.3:1992
4. Electric TCVN 5699-1:2004 √ IEC 60335-1:2001 Newer edition of std
instantaneous TCVN 5699-2-35:2001 IEC 60335-2-35:1997 IDT
water heaters
5. Microwave TCVN 5699-1:2004 √ IEC 60335-1:2001 Newer edition and use
Ovens TCVN 5699-2-25:2001 IEC 60335-2-25:1996 IDT of amd IEC std
Adm.1:1999
6. Electric rice TCVN 5699 -2-15-2000 √ IEC 60335-2-15:1995 Newer edition and use
cookers Adm.1:1999 of amd IEC std

Page 116 of 120

Version 12 – as of May 2010

Country Total Product STANDARDS REMARKS ON

Pleas
Product type or Domestic e tick
Relevant Extent of State reason if CHANGES
grouping Standards box if International Alignment MOD FROM
mand Standards PREVIOUS
atory
VERSION
7. Storage heating TCVN 5699-1:2004 √ IEC 60335-1:2001 IDT Newer edition
radiators
8. Hair dryer TCVN 5699-2-23:2000 √ IEC 60335-2-23:1996 IDT No change
9. Electric irons TCVN 5699-2-3:2000 √ IEC 60335-2-3:1993 IDT Use of amd IEC std
Adm.1:1999
10. Electric TCVN 6480-1:1999 √ IEC 60669-1:1993 IDT No change
Switches
11. Knife switches TCVN 6480-1:1999 √ IEC 60669-1:1993 IDT
and reverse knifes
witches
12. One - phase TCVN 6188 : 1996 √ IEC 884-1:1994 IDT
electric sockets TCVN 6190:1999 MOD
and Plugs
13. Electric Wires TCVN 6610−1 : 2000 √ IEC 60227−1:1993, IDT Use of amd IEC std
coated with PVC Adm.1:95
or PE TCVN 6610−3 : 2000 IEC 60227−3:1993, IDT
Adm.1:97
TCVN 6610−4 : 2000 IEC 60227−4:1992, IDT
Adm.1:97
TCVN 6612: 2000 IEC 60228:1978, IDT
Adm.1:1993
TCVN 6613: 2000 IEC 332 : 1993 IDT
TCVN 6614−1−1 : 2000 IEC 811−1−1 : 1993 IDT
TCVN 6614−1−2 : 2000 IEC 811−1−2:1985 IDT
Adm.1: 1989
TCVN 6614−1−4 : 2000 IEC 811−1−4:1985 IDT
Adm.1: 1989
IDT
TCVN 6614−3−1 : 2000 IEC 811−3−1:1985
Adm.1: 1994
IDT
TCVN 6614−3−2 : 2000 IEC 811−3−2:1985
Adm.1: 1993
14. Electric motors TCVN 6627−1 :2000 √ IEC 34−1:1994 IDT Use of amd IEC std
and generators Adm.1:1996
TCVN 6627−3:2000 IEC 34−3:1988 IDT
TCVN 6627−8:2000 IEC 34−8:1972 IDT
Adm.1:1990
TCVN 6627−9:2000 IEC 34−9:1990 IDT
Adm.1:1995
TCVN 6627−2 :2001 IEC 34−2:1972 IDT
Adm.1:1995
TCVN 6627−2A :2001 IEC 34−2A:1974 IDT

Page 117 of 120

Version 12 – as of May 2010

V. MODE OF REGULATION AND TYPES OF CONFORMITY ASSESSMENT REGIMES

COUNTRY TYPES OF CON- MODE OF REGULATION

FORMITY ASSESS-
MENT REGIMES
Vietnam Registration/Certificat The procedures for certification of those products where certification is mandatory is as follows:
ion
• Application
• Plan for assessment
• Assessment of conformity to standards
• Type Test/ Testing result + Surveillance (local product)
• Assessment
• Awarding of Certification
• Surveillance

Registration/Import- The procedures for import-export goods control

Export Goods Control • Application
• Type sampling
• Testing sample (s)
• Assessment
• Notification of control result

Page 118 of 120

Version 12 – as of May 2010

VI. FLOWCHART OF MEMBER COUNTRIES’ REGIME

VIET NAM

The procedures for Certification on safety The procedures for import-export goods control

Supplier: Supplier submits the Register to Inspection Body

- Sending type sample (s) to designated testing lab.
- Collecting the testing Report

- Sampling by Ins. Body

- Establishing a technical document by supplier - Sending sample (s) to designated testing lab.
Supplier - Sending to STAMEQ
- Collecting the Testing Report

Assessment the technical document by STAMEQ

Assessment testing report with relevant standards by Ins. Body

STAMEQ grants Certification

Ins. Body grants the Notification of controlled result to supplier

Surveillance Post-Certification

Page 119 of 120

Version 12 – as of May 2010

VII. MAINS VOLTAGE, FREQUENCY AND MAINS PLUG CONFIGURATION

Country Mains Mains Applicable Mains Plug Configuration

Voltage Frequency Legislation Domestic Please tick Relevant Extent of Diagram of Mains Plug Configuration-
and and Standard box if International Alignment
Tolerance Tolerance mandatory Standard -
Vietnam rated 50 Hz The List of TCVN 6190:1999 No IEC 884-1:1994 MOD
voltage not impot-expot Plugs and socket-
more than Goods outlets for
250V for subject to the household and
single state quality similar purpose-
phase inspection Types and main
dimensions

VIII. CONTACT PERSON

Country Contact Person and Address

Viet Nam Mr. Luong Van Phan
Deputy Director
International Cooperation
STAMEQ - Vietnam
Address: 70 Tran Hung Dao- Hanoi - Vietnam
Tel: 84 4 9 423243
Fax: 84 4 9 422418
[Link]: khht@[Link]

Page 120 of 120

Updated Regulatory Regime of Cambodia July 2012
No ratings yet
Updated Regulatory Regime of Cambodia July 2012
8 pages
Electrical Product Safety Guide
No ratings yet
Electrical Product Safety Guide
13 pages
General Specification For M&E Works: No. Standard Description
No ratings yet
General Specification For M&E Works: No. Standard Description
1 page
Regulated Electrical Equipment List
No ratings yet
Regulated Electrical Equipment List
11 pages
Contactor Selection For Switchgear As IEC Std.
100% (21)
Contactor Selection For Switchgear As IEC Std.
30 pages
Standards Proposal List For BSTI (HAP, KAP, EAP)
No ratings yet
Standards Proposal List For BSTI (HAP, KAP, EAP)
20 pages
Fluorescent Light Regulations in Malaysia
No ratings yet
Fluorescent Light Regulations in Malaysia
43 pages
TELEMECANIQUE Contactor
100% (2)
TELEMECANIQUE Contactor
252 pages
Regulated Electrical Equipment List
No ratings yet
Regulated Electrical Equipment List
11 pages
IEC Standards
No ratings yet
IEC Standards
22 pages
List of IEC Standards
No ratings yet
List of IEC Standards
14 pages
Moeller Certificates
No ratings yet
Moeller Certificates
44 pages
Reg Regime of Indonesia - Asof - 2 Nov 2017
No ratings yet
Reg Regime of Indonesia - Asof - 2 Nov 2017
17 pages
Info Iec60038 (Ed6.2) en D
No ratings yet
Info Iec60038 (Ed6.2) en D
4 pages
List of IEC Standards
100% (2)
List of IEC Standards
13 pages
IEC Standards Reference Guide
No ratings yet
IEC Standards Reference Guide
11 pages
Performance Standards for Household Appliances
No ratings yet
Performance Standards for Household Appliances
15 pages
List of Applicable Electrical Standards
82% (11)
List of Applicable Electrical Standards
3 pages
IEC Standards Overview for Electrical Equipment
100% (2)
IEC Standards Overview for Electrical Equipment
52 pages
IEC 60063 Preferred Number Series For Resistors and Capacitors
No ratings yet
IEC 60063 Preferred Number Series For Resistors and Capacitors
52 pages
Standards Equipments For BSTI
No ratings yet
Standards Equipments For BSTI
20 pages
?kjsyw VKSJ Leku Fo - QR Lkfèk Kkas DH LQJ (KK: HKKJRH Ekud
No ratings yet
?kjsyw VKSJ Leku Fo - QR Lkfèk Kkas DH LQJ (KK: HKKJRH Ekud
22 pages
IEC Safety Standards for Electrical Appliances
100% (1)
IEC Safety Standards for Electrical Appliances
117 pages
Electrical Prodcut Certification by Sirim
No ratings yet
Electrical Prodcut Certification by Sirim
20 pages
IEC Standards
No ratings yet
IEC Standards
5 pages
Elmark 2008 EN
No ratings yet
Elmark 2008 EN
162 pages
36 KV Vacuum Circuit Breakers 1. SCOPE
No ratings yet
36 KV Vacuum Circuit Breakers 1. SCOPE
20 pages
Standards and Environmental Conditions
No ratings yet
Standards and Environmental Conditions
2 pages
Iec Standard
No ratings yet
Iec Standard
10 pages
Applicable Standard Proposal Format - Fuad
No ratings yet
Applicable Standard Proposal Format - Fuad
9 pages
Power Plant Codes & Standard
No ratings yet
Power Plant Codes & Standard
15 pages
Untitled Extract Pages
No ratings yet
Untitled Extract Pages
1 page
IEC Standards List Overview
No ratings yet
IEC Standards List Overview
9 pages
IEC Regulations
No ratings yet
IEC Regulations
9 pages
AppendixEL 02schedule D 1
No ratings yet
AppendixEL 02schedule D 1
431 pages
IP66 Isolator: Description Pack Qty
No ratings yet
IP66 Isolator: Description Pack Qty
18 pages
IEC Standards List Overview
No ratings yet
IEC Standards List Overview
69 pages
Industrial Switchgear Specs
No ratings yet
Industrial Switchgear Specs
12 pages
Iec Codes PDF
No ratings yet
Iec Codes PDF
257 pages
Bunder Al Khairan VENDER LIST
No ratings yet
Bunder Al Khairan VENDER LIST
6 pages
List of Iec Standards
No ratings yet
List of Iec Standards
9 pages
Indonesia Procurement Standards
No ratings yet
Indonesia Procurement Standards
18 pages
Medium Voltage Switchgear Specs
No ratings yet
Medium Voltage Switchgear Specs
24 pages
Seminar Tawau - Kawalselia Kelengkapan Elektrik
No ratings yet
Seminar Tawau - Kawalselia Kelengkapan Elektrik
43 pages
Names of Codes For Electrical Works
No ratings yet
Names of Codes For Electrical Works
8 pages
IEC Standards Overview: Electrical & Electronic Systems
100% (1)
IEC Standards Overview: Electrical & Electronic Systems
6 pages
Three - Phase Asynchronous Motor-SC-MOTOR
No ratings yet
Three - Phase Asynchronous Motor-SC-MOTOR
24 pages
Low-Voltage Switchgear Standards
No ratings yet
Low-Voltage Switchgear Standards
3 pages
27100
No ratings yet
27100
4 pages
Duro-Test Lamp Catalog 1985
100% (2)
Duro-Test Lamp Catalog 1985
34 pages
1000-400-933 - D-X8000 Light Source Service Guide
No ratings yet
1000-400-933 - D-X8000 Light Source Service Guide
84 pages
Military Land Rover Ignition Guide
No ratings yet
Military Land Rover Ignition Guide
92 pages
AS 1680.3-1991: Interior Lighting Standards
No ratings yet
AS 1680.3-1991: Interior Lighting Standards
55 pages
Electronic Ballst
No ratings yet
Electronic Ballst
53 pages
Zones 1&2 21&22: Lighting Technology
No ratings yet
Zones 1&2 21&22: Lighting Technology
6 pages
Make A High Voltage Supply in 5 Minutes
No ratings yet
Make A High Voltage Supply in 5 Minutes
11 pages
Hydroponic Gardening For Beginners
100% (1)
Hydroponic Gardening For Beginners
55 pages
Wide-Lite F Series Floodlight Bulletin 1988
No ratings yet
Wide-Lite F Series Floodlight Bulletin 1988
4 pages
Zennio Catalogo 2016 en
No ratings yet
Zennio Catalogo 2016 en
56 pages
Contractor's Guide to BCA Part J6
No ratings yet
Contractor's Guide to BCA Part J6
13 pages
Paper 3 Set B
No ratings yet
Paper 3 Set B
17 pages
16520
No ratings yet
16520
5 pages
Catalog Gama Axolute
No ratings yet
Catalog Gama Axolute
160 pages
Grade 10 Third Quarter Eim Tle
No ratings yet
Grade 10 Third Quarter Eim Tle
3 pages
Air Conditioning Tools Overview
0% (1)
Air Conditioning Tools Overview
20 pages
Ignition System Maintenance Essentials
No ratings yet
Ignition System Maintenance Essentials
31 pages
Universal - Ballast Basics I
No ratings yet
Universal - Ballast Basics I
30 pages
Lighting Specification
100% (1)
Lighting Specification
89 pages
SOP-Lighting Repair and Replacement
No ratings yet
SOP-Lighting Repair and Replacement
4 pages
Type (A) : Description
No ratings yet
Type (A) : Description
10 pages
Utilization of Electrical Energy
No ratings yet
Utilization of Electrical Energy
63 pages
Cv. Tekno Asri: Electronic Load Controller (ELC)
No ratings yet
Cv. Tekno Asri: Electronic Load Controller (ELC)
2 pages
Recessed Cooper FailSafe Vandal Resistant CFL RCSRDRRDSEDR
No ratings yet
Recessed Cooper FailSafe Vandal Resistant CFL RCSRDRRDSEDR
6 pages
Electronic Ballast Controller of A Fluorescent Lamp Using IR21571
100% (1)
Electronic Ballast Controller of A Fluorescent Lamp Using IR21571
16 pages
Walsall Hazardous Area, Flame & Explosion Proof Distribution Boards
No ratings yet
Walsall Hazardous Area, Flame & Explosion Proof Distribution Boards
13 pages
University: ANSI/ASHRAE/IES Standard 90.1-2010 Power and Lighting
No ratings yet
University: ANSI/ASHRAE/IES Standard 90.1-2010 Power and Lighting
53 pages
Flicker Fact-Sheet PDF
No ratings yet
Flicker Fact-Sheet PDF
4 pages