GOVERNMENT OF RAJASTHAN

Public Health Department (PHED)

FATEHPUR-LAXMANGARH WATER SUPPLY

Project: -
PROJECT UNDER JJM DIST.- SIKAR, PAKAGE -2

THE ADDITIONAL CHIEF ENGINEER (P), PHED,

CLIENT: -
REGION - JHUNJHUNU

CONTRACTOR:
M/S BRCC-KCC(JV)
-

CONSULTANT: - GYANVI TECHNICAL SERVICES

RCC DESIGN CALCULATIONS OF CWR FOR CAPACITY-

Document Title
10KL

Revisio Checked Submitted

Date Prepared By Forwarded by
n No by by
Assistant Executive
Engineer Engineer
GYANVI
M/S BRCC- PHED- Sub. PHED- Project
R0 14.12.2024 TECHNICAL L.L. Guru
KCC(JV) DN. DN.
SERVICES
Laxmangarh Laxmangarh
(Raj.) (Raj.)
T.O.C. + 1.375 M

0.30 M
FREE BOARD

LIVE STORAGE
2.05 M

2.50 M
GL = 0.00 M

F.L. -1.2 M
0.10 M DEAD STORAGE
 1.0_Inputs for Design of CWR
SALIENT FEATURES:
Capacity of CWR 10.00 KL
Internal Dia of CWR (m) 2.50 m
Height of water column 2.05 m
Free Board 0.30 m
Dead Storage 0.10 m
Depth Below ground Level (m) 1.20 m
Grade of Concrete/Reinforcement/Steel
RCC
Water Retaining structure M35
PCC M15
Reinforcement Fe-415, Confirming to IS: 1786
Density of RCC Concrete 25KN/m3
Density of water 10KN/m3
Thickness of Screed on Roof 75mm

Seismic Parameters
Seismic zone III
Zone Factor (z) 0.16
Importance Factor 1.5
Response Reduction Factor 2.5 as per IS 1893 2014 part -2

Soil Data
Soil Bearing Capacity 7 T/m2 at 1.2 m Depth
Density of soil 17KN/m3
Water table Water table was not encountered up to the depth of
Investigation as per SBC Report.

CODES
Code No. Title
IS: 456-2000
Code of Practice plain & reinforced concrete
SP-16
Code for design Aids for reinforced concrete

IS:875(part2)-2015
Code of practice for design loads

IS: 1893 Part-2:2014 Code for criteria for earthquake resistant design of
structures
IS: 3370 part -2:2021 Code for criteria water retaining wall & floor
IS: 3370 part -4 :2021 Code for Design water retaining wall & floor

RCC DESIGN CALACULATIONS FOR CLEAR WATER RESERVIOR

CAPACITY 10.0 KL SBC 7.00 T/M2 SHAPE
 0
ZONE III TYPE PUG CIRCULA
R
CAPACITY SIZING
Total capacity of CWR = 10 KL
No of CWR = 1
Design Capacity of reservoir, (C). = 10.00 KL
Safe bearing pressure of soil = 7.00 T/Sqm.
Safe bearing pressure of soil adopted = 7.00 T/Sqm.
Assume inner diameter of vertical wall (D1) = 2.50 Meters.
Dead storage provided. = 0.10 Meters.
Volume reduction due to columns supporting stair case head = 0.00 Cum.
room
volume reduction by column supporting flat slab = 0.00 Cum.
volume reduction by column head = 0.00 Cum.
Volume reduction due to RCC stair case = 0.00 Cum.
Total volume reduction = 0.00 Cum.
Gross volume of container required in live storage height = 10.00 Cum.
Gross volume of container provided in live storage height = 10.06 Cum.
Net volume of container provided in live storage height = 10.06 Cum.
Height of live storage provided = 2.05 Meters.
Height of water column including dead storage = 2.15 Meters.
Free board adopted = 0.30 Meters.

Depth of edge beam considered in water 0.00 = 0.00 Meters.

column
Water Column considered in vertical wall 2.15+0.3 = 2.450 Meters.
design
RC DESIGN OF CIRCULAR FLAT ROOF SLAB FOR 10 KL CWR
GENERAL DATA
GRADE OF CONCRETE M = 35 N/mm2
GRADE OF STEEL Fe = 415 N/mm2
σ
Permissible Stress in concrete cbc = 11.5 N/mm2
σ
Permissible Stress in steel st = 130 N/mm2
Cover = 45 mm
m = 8.12
kc = 0.42
DESIGN CONSTANT
jc = 0.86
Rc = 2.08
DIA OF CIRCULAR SLAB D = 2.50 M
Radius OF CIRCULAR SLAB R = 1.25 M
LOAD CALCULATIONS
DEAD LOAD = 375.00 Kg/m2
LIVE LOAD = 200.00 Kg/m2
FINISH LOAD = 180.00 Kg/m2
TOTAL LOAD = 755.00 Kg/m2
AREA OF SLAB = 4.91 m2
THK OF TOP SLAB PROVIDED = 125.00 MM
PREMISSIBLE CONCRETE STRESS FOR M35 = 2.20 N/MM2
As per IS-456 Annexure-B clause B-2.3 = 1.33
increase in permissible stresses due to
wind load & seismic
UNCRACKED SECTION FACTOR = 4.88

DESIGN OF TOP RING BEAM

Breadth 250
Depth = 250 mm
= mm
Hoop Tension (Ft)
9.4375 9.44 kN
=

72.60
Hoop Tension=
mm2

Diameter of bar = 10 mm

Required No. of bars = 1 Nos

Provide No. of bars = 4 Nos

DESIGN CALCULATION OF CIRCULAR SLAB
BOTTOM FACE REINFORCEMENT DETAIL (RADIALS)
DISTANCE BENDING BENDIN Ast Ast Req Eff. Thk Bar Dia at Spacing Spacing Ast Prov at
(M) MOMEN G Req Temp (mm) Bottom req (mm) prov at bottom(mm
COFFICEN MOMEN (mm2 (mm2) (mm) (At Bottom 2)
T T ) Radials Bottom) Face(mm)
Knm/m
0.0 R 0.000 0.0625 0.00 0.00 300 75 10 262 250 314.00
0.1 R 0.125 0.0606 0.01 0.16 300 75 10 262 250 314.00
0.2 R 0.250 0.0550 0.03 0.58 300 75 10 262 250 314.00
0.3 R 0.375 0.0456 0.05 1.07 300 75 10 262 250 314.00
0.4 R 0.500 0.0325 0.06 1.36 300 75 10 262 250 314.00
0.5 R 0.625 0.0156 0.05 1.02 300 75 10 262 250 314.00
0.6 R 0.750 -0.0050 0.02 0.47 300 75 10 262 250 314.00
0.7 R 0.875 -0.0294 0.17 3.77 300 75 10 262 250 314.00
0.8 R 1.000 -0.0575 0.43 9.63 300 75 10 262 250 314.00
0.9 R 1.125 -0.0894 0.85 18.97 300 75 10 262 250 314.00
1.0 R 1.250 -0.1250 1.47 32.79 300 75 10 262 250 314.00

CIRCUM REINFORCEMENT DETAIL AT BOTTOM COVER: - 45 MM SHEAR CHECK

DISTANCE BENDING BENDIN Ast Eff. Thk Ba Dia Spacing Spacing % STEEL ζv ζc
(M) MOMEN G Req (mm) (mm) req (mm) prov (mm) (N/mm (N/mm2
2

COFFICEN MOMEN ) )
S.NO DISTANC T T
. E
0.0 R 0.000 0.0625 0.0000 300.0 75 10 262 200 OK 0.42 0.00 0.44
0.1 R 0.125 0.0619 0.0073 300.0 75 10 262 250 OK 0.42 0.00 0.44
0.2 R 0.250 0.0600 0.0283 300.0 75 10 262 250 OK 0.42 0.00 0.44
0.3 R 0.375 0.0569 0.0604 300.0 75 10 262 250 OK 0.42 0.15 0.44
0.4 R 0.500 0.0525 0.0991 300.0 75 10 262 250 OK 0.42 0.08 0.44
0.5 R 0.625 0.0469 0.1383 300.0 75 10 262 250 OK 0.42 0.05 0.44
0.6 R 0.750 0.0400 0.1699 300.0 75 10 262 250 OK 0.42 0.03 0.44
0.7 R 0.875 0.0319 0.1844 300.0 75 10 262 250 OK 0.42 0.01 0.44
0.8 R 1.000 0.0225 0.1699 300.0 75 10 262 250 OK 0.42 0.02 0.44
0.9 R 1.125 -0.0119 0.1137 300.0 75 10 262 250 OK 0.42 0.03 0.44
1.0 R 1.250 0.0000 0.0000 300.0 75 10 262 250 OK 0.42 0.04 0.44
DESIGN OF OUTER VERTICAL WALL (CASE-1 - WATER INSIDE AND NO SOIL OUTSIDE)
CONC. MIX M 35
Assuming thickness of wall at base = 15.00 Cm.

Height of uniform thickness from top = 0.00 M

Assuming thickness of wall at top = 15.00 Cm.

Weighted average thickness = 15.00 Cm.

H^2/Dt = 12.33

cover = 45 mm
The vertical wall shall be design in accordance to the recommendation given in clause
5.4.b. of IS: 3370 (Part II). The values of the coefficients for moments & Hoop tension
shall be calculated by interpretation from the following tables
Table No.8 IS:3370(part-IV)-2021 for coefficient for bending moment in cylindrical
wall with fixed base free top and subject to triangular load (clause 3.1.1 of IS: 3370
Part IV). IS code have coefficient values for H 2/DT value only up to 16.
CALCULATION FOR BENDING MOMENT
From the above Two tables, values of coefficient for bending moment and Hoop
tension have been interpolated for the corresponding value of H^2/Dt. The value of
bending moment and Hoop tension at different heights in wall have been shown in the
following tables.
Depth Below TWL Coeff. Coeff. Coeff. Bendin Requir Provid Area Area
g ed ed of of
depth depth sreel sreel
rqd rqd
for for
B.M. B.M.
for for for Mome
nt
FRACTIO METER B.M. B.M. B.M. Near Near
N S water outer
Face Face

H^2/Dt-- 12.0 14.0 12.33 KNm./ mm mm sqmm sqmm

> m.
0.1H 0.215 0.0000 0.0000 0.000 0.000 0.00 150 0.000 0.00
0
0.2H 0.430 - 0.0000 - -0.009 5.00 150 0.693 0.00
0.0001 0.000
1
0.3H 0.645 0.0001 0.0000 0.000 0.009 5.00 150 0.000 0.69
1
0.4H 0.860 0.0002 0.0000 0.000 0.017 7.00 150 0.000 1.31
2
0.5H 1.075 0.0003 0.0001 0.000 0.027 9.00 150 0.000 2.08
3
0.6H 1.290 0.0013 0.0008 0.001 0.121 19.00 150 0.000 9.40
2
0.7H 1.505 0.0023 0.0019 0.002 0.223 25.00 150 0.000 17.26
 2
0.8H 1.720 0.0026 0.0023 0.002 0.254 27.00 150 0.000 19.72
6
0.9H 1.935 - -0.0001 - -0.044 11.00 150 3.390 0.00
0.0005 0.000
4
1.0H 2.150 - -0.0090 - -1.012 53.00 150 78.42 0.00
0.0104 0.010 8
2
Requirement/Provision of Vertical Reinforcement Bars
Depth Water Face Soil Face
below
TWL
Meters Min. Area of Bar dia Spacin Spacing Area of Bar Spacin Spaci
Temp steel combina g rqd provide steel dia g rqd ng
Steel reqd. tion d reqd. combi provid
Rqd nation ed
Near
Each
Face
sqmm mm mm mm c/c mm2 mm mm mm
c/c
0.215 180.0 180.0 8.0 279.1 260.0 180.0 8.0 279.1 260.0

0.430 180.0 180.0 8.0 279.1 260.0 180.0 8.0 279.1 260.0

0.645 180.0 180.0 8.0 279.1 260.0 180.0 8.0 279.1 260.0

0.860 180.0 180.0 8.0 279.1 260.0 180.0 8.0 279.1 260.0

1.075 180.0 180.0 8.0 279.1 260.0 180.0 8.0 279.1 260.0

1.290 180.0 180.0 8.0 279.1 260.0 180.0 8.0 279.1 260.0

1.505 180.0 180.0 8.0 279.1 260.0 180.0 8.0 279.1 260.0

1.720 180.0 180.0 8.0 279.1 260.0 180.0 8.0 279.1 260.0

1.935 180.0 180.0 8.0 279.1 260.0 180.0 8.0 279.1 260.0

2.150 180.0 180.0 8.0 279.1 260.0 180.0 8.0 279.1 260.0
BOTTOM SECTION OF WALL
Coefficient for design of uncracked section = 3.33
Maximum -ve bending moment at the base of wall = -1.01 KN.M/M
Maximum +ve bending moment = 0.25 KN.M/M
Mi. Overall thickness reqd. for uncracked sec. = 55.07 mm.
(-1.01)/3.33) ^0.5
Overall thickness of wall provided at OK = 150 mm.
base is
Dia. of bar proposed to be used 8 mm + = 8 mm.
Effective depth of section available = 101.00 mm.
base
Area of steel required considering = 77.52 Sq.mm.
B.M.
Spacing of bars required = 648.10 mm.
Spacing of bars provided = 260.00 mm.
Area of steel actually provided = 0.19 Sq.cm.
BASE SHEAR FOR SIESMIC FORCES
base shear for impulsive mode Vi = 39.80 Kn
Base shear for convective mode Vc = 14.03 Kn
Resultant Base shear (Vi = 42.20 Kn
2
+Vc2)
Sectional area of wall = 1.18 sqm
Shear stress due to seismic forces = 0.036 n/mm2
% steel available on water face at the = 0.19 %
base of wall
corresponding allowable stress = 0.339 n/mm2
OK

Spring mass model for Seismic analysis as per IS 1893:2014 (Part 2)

For Ground supported tanks: Outer Wall
Type of tank ======> circular
Select Seismic Zone III
Select Soil Type Medium Soil
Zone Factor, Z = 0.16
Importance Factor, I = (Table:1, IS 1893 (Part-2) 1.5
SBC 7.00 T/m2
Parameters for the circular tank Parameters for the circular tanks can be obtained from Fig 2 and for the
rectangular tanks these parameters can be obtained from the Fig 3, which has been shown as below

Parameters can be determined for impulsive and convective mode by h/D ratio; where
"h" is the depth of water in the tank and the "D" is the diameter of the tank

height of water column in the tank is h= 2.45 m

Dia meter of the tank is D= 2.50 m
height/Diameter, h/D = h/D = 0.98
Diameter/height, D/h = D/h = 1.02
Density of water p= 10 KN/m3
Thickness of wall at top t= 0.15 m
Weight of water in container m= 120.2 KN
Corresponding to h/D ratio from Fig. 2 of IS 1893 (Part 2) :2014
Kch/mg = 0.834
 mi/m = 0.802
mc/m = 0.234
hi/h = 0.40434
hc/h = 0.737
hi*/h = 0.499
hc*/h = 0.753
Ci 4.231
Cc 3.305

Depth of the tank below the ground = 1.2 m

Total height of wall of the tank = 2.15 m
Response Reduction Factor (For = 2.5
SMRF) R =
Damping For the impulsive mode = 5 %
Damping For the convective mode = 0.5 %
As per the clause no 4.5.2 of IS Code 1893:2014 (part-2) the multiplying factors for the following
mode for damping
will be
Multiplying factor
For the impulsive mode 1
For the convective mode 1.75

Determination of average response acceleration coefficient

Sa/g
For the impulsive mode 0.786
For the convective mode 1.059

Design of Horizontal seismic

coefficient
 Ah= Z*I*Sa/(2*R*g)
For the impulsive mode 0.038
= Ahi
For the convective mode 0.051
= Ahi
Calculation for hydrodynamic pressure
Lateral Lateral pressure vertical
Height of wall Thk of resultant
S.No. Qiw impulsive Qcw convective due to wall ground
above base section pressure
pressure pressure inertia acceleration
From To cm Piw (kg) Pcw (kg) Pww Pv Kg
1 1.94 2.15 15 0.000 0 0.5625 2161 138.77 74.01 2167
2 1.72 1.94 15 0.126 194 0.4108 1420 138.77 127.05 1464
3 1.51 1.72 15 0.238 326 0.3004 923 138.77 180.09 1049
4 1.29 1.51 15 0.338 404 0.2202 592 138.77 233.13 836
5 1.08 1.29 15 0.424 435 0.1622 374 138.77 286.17 742
6 0.86 1.08 15 0.497 425 0.1206 232 138.77 339.21 698
7 0.65 0.86 15 0.556 381 0.0911 140 138.77 392.26 666
8 0.43 0.65 15 0.602 309 0.0707 82 138.77 445.30 637
9 0.22 0.43 15 0.636 217 0.0575 44 138.77 498.34 614
10 0.00 0.22 15 0.655 112 0.0501 19 138.77 551.38 606

Calculation for reinforcement required

Min Total steel
Total steel Adopted
Height of wall Thk of Seismic hoop Total temp reqd with Actual permissible
reqd without area of steel
above base section force forces force steel seismic stress stress
seismic force reqd
reqd forces
From To cm Kg Kg Kg Sqcm Sqcm Sqcm Sqcm Kg/cm2 Kg/cm2
1.94 2.15 15 2167 -5 2162 3.60 0.00 1.25 1.25 1.38 21.28 OK
1.72 1.94 15 1464 260 1724 3.60 0.20 1.00 1.00 1.10 21.28 OK
1.51 1.72 15 1049 529 1579 3.60 0.41 0.91 0.91 1.01 21.28 OK
1.29 1.51 15 836 810 1647 3.60 0.62 0.95 0.95 1.05 21.28 OK
1.08 1.29 15 742 1117 1859 3.60 0.86 1.08 1.08 1.19 21.28 OK
0.86 1.08 15 698 1450 2147 3.60 1.12 1.24 1.24 1.37 21.28 OK
0.65 0.86 15 666 1782 2448 3.60 1.37 1.42 1.42 1.56 21.28 OK
0.43 0.65 15 637 2020 2657 3.60 1.55 1.54 1.55 1.69 21.28 OK
0.22 0.43 15 614 1949 2563 3.60 1.50 1.48 1.50 1.63 21.28 OK
0.00 0.22 15 606 1298 1904 3.60 1.00 1.10 1.10 1.21 21.28 OK
 CALCULATION FOR HOOP REINFORCEMENT FOR HINDGE BASE WITH FREE TOP & FIXED BASE WITH FREE TOP
HINGE BASE WITH FREE TOP
Depth Coeff. For Hoop Coeff. For Hoop Coeff. For Hoop Tension Hoop Hoop Hoop Max Hoop
Below Tension for Tension for Hoop for Hinge Reinforcement Reinforcement Reinforcement Reinforcement
(m) Hinge Base and Hinge Base and Tension Base and due to Hoop due to Temp. due to seismic per m
Free Top Free Top Free Topper Tension per m Steel per m force per m
"m"
H^2/ 14.0 16.0 12.33 0.24
Dt-->
Kg. Sq. cm Sq. cm Sq. cm Sq. cm
0.0H -0.0020 0.000 -0.0017 -5 -0.0035 3.60 1.10 3.60
0.1H 0.0970 0.096 0.0968 260 0.2002 3.60 1.50 3.60
0.2H 0.1970 0.197 0.1970 529 0.4073 3.60 1.55 3.60
0.3H 0.3020 0.299 0.3015 810 0.6233 3.60 1.42 3.60
0.4H 0.4170 0.408 0.4155 1117 0.8590 3.60 1.24 3.60
0.5H 0.5410 0.531 0.5394 1450 1.1150 3.60 1.08 3.60
0.6H 0.6640 0.659 0.6632 1782 1.3710 3.60 0.95 3.60
0.7H 0.7500 0.761 0.7518 2020 1.5542 3.60 0.91 3.60
0.8H 0.7200 0.752 0.7252 1949 1.4993 3.60 1.00 3.60
0.9H 0.4770 0.513 0.4829 1298 0.9983 3.60 1.25 3.60

CALCULATION FOR HOOP REINFORCEMENT

The Hoop force at different heights in wall have been calculated in the following table. The table also shows calculation of Hoop reinforcement and check
for thickness of wall required at different heights to limit the tensile stress on equivalent area less than 15.0 Kg./Sq.cm.
TABLE SHOWING CALCULATIONS FOR HOOP REINFORCEMENT
Top thickness shall be provided up to 0.00
M from top, keeping the direct tensile stress in concrete in permissible limits 16.00
of Kg/Sq.cm.
Depth Dia. Of Hoop bar Spacing of hoop Spacing of Thickness of Tensile Stress on Height Above No of bars Height covered
Below m chosen bars required hoop bars wall available equ. Area Base Mtr. provided Nos. by hoop bars
per cm Cm C/C provided Cm Kg/Sq.cm. Cms.
Cm C/C
0.0H 8.00 13.96 13.50 15.00 0.00 2.45 2 250
0.1H 8.00 13.96 13.50 15.00 0.17 2.21 2 223
0.2H 8.00 13.96 13.50 15.00 0.35 1.96 2 196
0.3H 8.00 13.96 13.50 15.00 0.54 1.72 2 169
0.4H 8.00 13.96 13.50 15.00 0.74 1.47 2 142
0.5H 8.00 13.96 13.50 15.00 0.97 1.23 2 115
0.6H 8.00 13.96 13.50 15.00 1.19 0.98 2 88
0.7H 8.00 13.96 13.50 15.00 1.35 0.73 2 61
0.8H 8.00 13.96 13.50 15.00 1.30 0.49 2 34
0.9H 8.00 13.96 13.50 15.00 0.87 0.24 2 14
DESIGN OF WALL FOOTING:
CONCRETE MIX M = 3
5
THICKNESS OF FOUNDATION SLAB ASSUMED THFS = 2 CM
0
DEPTH OF FOOTING BELOW GROUND DOF1 = 1.20 M
UNIT WEIGHT OF SOIL = 1700.00 KG /
Cu.M
SAFE BEARING PRESSURE SBP = 7000 KG /
SQ.M
MAX.ALLOW. GROSS LOADING AT FOOTING SLF = 7000 KG /
LEVEL SQ.M
ASSUMING WIDTH OF HEEL SLAB HWID = 0.60 M
ASSUMING WIDTH OF TOE SLAB TWID = 0.30 M
WIDTH OF WALL AT BASE = 0.15
TOTAL WIDTH OF FOOTING SLAB FWID = 1.05 M
THE FOLLOWING TABLE GIVES CALCULATION OF LOAD AND MOMENTS ON THE FOOTING
LOAD DUE TO LOAD PER DISTANCE FROM
ITEM METER EDGE OF HEEL
KG M KG-M
VERTICAL WALL PART 1 919 0.675 620
VERTICAL WALL PART 2 0 0.000 0
WT. FROM ROOF 472 0.675 319
WT. OF WATER 1290 0.300 387
WT. OF BASE SLAB 525 0.525 276
NET MOMENT DUE TO WATER 101
T 3
1702
OTAL 206

DISTANCE OF POINT OF CROSSING OF

RESULTANT
WITH BASE FROM EDGE OF HEEL SLAB
Z = 0.53 M
ECCENTICITY OF LOADING
E = 0.006 M
MAX. SOIL PRESSURE NEAR EDGE OF TOE
5096.17*(1+6*0.06/1.05)/1.05 MXP = 3 KG / SQ.M
1 159
MIN. SOIL PRESSURE NEAR EDGE OF HEEL
5096.17*(1-6*0.06/1.05)/1.05 MNP = 2 KG / SQ.M
1 947
DESIGN OF TOE SLAB:

MAX. PRESSURE AT FREE EDGE = 3159 KG /

SQ.M
PRESSURE AT WALL EDGE OF TOE = 3098 KG /
SQ.M
MAX. BENDING MOMENT = 141.3 KG-
M
DEDUCT MOMENT DUE TO SELF WEIGHT = 22.50 KG-
M
NET DESIGN MOMENT FOR TOE SLAB = 118.75 KG-
M
COEFFICIENT FOR UNCRACKED SECTION 3.33
MIN. THICKNESS REQUIRED = 5.97 Cm
OVERALL THICKNESS PROVIDED IS OK 20.00 Cm
CHOOSE DIA. OF BARS AS = 8.00 MM
CLEAR COVER TO BE PROVIDED = 50 MM
EFFECTIVE DEPTH AVAILABLE = 14.60 CM
AREA OF STEEL REQUIRED = 0.73 SQ.C
M
253.67/(13.00*14.50*0.86)
SPACING OF BARS REQUIRED = 69.06 CM
C/C
PROVIDED 8.00 MM VERTICAL BARS 26.00 CM
EXTENDED.FROM INNER FACE C/C
+ 8 OF WALL @
DESIGN OF HEEL SLAB:
cover = 50
UPWARD SOIL PRESSURE = 1831.79 KG
MOMENT DUE TO UPWARD PRESSURE = 543.16 KG-
M
DOWNWARD WATER PRESSURE = 1290.00 KG
DOWNWARD PRESSURE DUE TO SELF WEIGHT = 300.00 KG
MOMENT DUE TO DOWNWARD PRESSURE = 477.00 KG-
M
NET DESIGN MOMENT = -66.16 KG-
M
coefficient for uncracks section = 3.33
DEPTH OF SECTION REQUIRED FOR UNCRACKED = 4.46 CM
DIA OF BAR CHOSEN F0R TOP FACE = 8.00 MM
EFFECTIVE DEPTH AVIALABLE = 14.60 CM
AREA STEEL REQUIRED = 0.41 SQ
CM
DIA OF BAR CHOSEN F0R LOWER FACE = 8.00 MM
PERCENTAGE TEMPERATURE STEEL REQUIRED = 0.24 %
AREA OF TEMP. STEEL REQD. = 4.80 SQ
CM
MIN AREA OF STEEL REQD. NEAR TOP FACE = 2.40 SQ
CM
SPACING OF BARS REQD.NEAR TOP FACE = 20.93 CM
C\C
SPACING OF BARS PROVIDED = 20.00 CM
C\C
Total AREA OF CIRCUM.TEMP. STEEL REQUIRED = 2.40 SQ
ON EACH FACE CM
DIA OF BARS = 8.00 MM
SPACING OF BARS ON EACH FACE = 20.0 CM
C\C

FLOOR SLAB
CONCRETE MIX: M = 35.00
The floor slab is directly supported on the
ground
and is non-structural. As such only temp. steel is
reqd.
Provide thickness of floor slab as = 20.00 Cm.
Temperature steel required = 0.240 %
Area of steel required = 2.400 Sq.c
m.
Diameter of bar chosen = 8.000 mm.
Spacing of bars near both faces required = 20.93 Cm.C
/C
3.14/4*8.00^2/2.40
Spacing of bars provided = 20.00 Cm.C
/C

DESIGN OF OUTER WALL (CASE 2-NO WATER INSIDE AND SOIL OUTSIDE)
COEFF. FOR EARTH PRESSURE = 0.30
Depth of floor below ground level = 1.2 M
THK. OF WALL AT BASE = 15.00 CM
THK AT 1.2 M ABOVE = 15.00 cm
FLOOR
WEGHED THK = 15.00 cm
H2/DT = 3.840
DEPTH BELOW G.L. B.M. B.M. B.M.
COEF COEF COEFF. BM
F. F.
FRACTION METER 1.2 1.6 3.84
0.1H 0.12 0.001 0.001 0.00055 0.485
2 1
0.2H 0.24 0.004 0.004 0.00354 3.120
2 1
0.3H 0.36 0.007 0.007 0.00638 5.623
7 5
0.4H 0.48 0.010 0.010 0.01294 11.404
3 7
0.5H 0.60 0.011 0.012 0.01714 15.105
2 1
0.6H 0.72 0.009 0.011 0.02286 20.146
0 1
0.7H 0.84 0.002 0.005 0.02596 22.878
2 8
0.8H 0.96 - - 0.02682 23.636
0.010 0.005
8 1
0.9H 1.08 - - 0.02104 18.542
0.031 0.023
1 2
1.0H 1.20 - - 0.00382 3.366
0.060 0.050
2 5
COVER = 35.00 mm.
EFFECTIVE DEPTH AVAILABLE AT BASE = 11.10 CM
MAX NEGETIVE B.M. AT BASE = 23.64 KG-
M
AREA OF STEEL REQD. = 0.190 SQC
M
soil face mm
8 = 8.00 mm.
+
Spacing of Bars required = 263.78 cm
Spacing of Bars provided = 20.00 cm
Area of steel actually provided = 5.02 SQC
M
DESIGN OF WALL FOOTING:
CONCRETE MIX M = 35
THICKNESS OF FOUNDATION SLAB ASSUMED THFS = 20.00 CM
DEPTH OF FOOTING BELOW GROUND DOF1 = 1.20 M
UNIT WEIGHT OF SOIL = 1700.00 KG /
Cu.M
SAFE BEARING PRESSURE SBP = 7000.00 KG /
SQ.M
MAX.ALLOW. GROSS LOADING AT FOOTING LEVEL SLF = 7000.00 KG /
SQ.M
ASSUMING WIDTH OF HEEL SLAB HWID = 0.30 M
ASSUMING WIDTH OF TOE SLAB TWID = 0.60 M
WIDTH OF WALL AT BASE = 0.15 M
TOTAL WIDTH OF FOOTING SLAB FWID = 1.05 M
THE FOLLOWING TABLE GIVES CALCULATION OF LOAD AND MOMENTS ON THE FOOTING
LOAD DUE TO LOAD PER DISTANCE FROM
ITEM METER EDGE OF HEEL
KG M KG-M
VERTICAL WALL PART 1 919 0.3 345
75
VERTICAL WALL PART 2 0 0.0 0
00
472 0.3 177
WT. FROM ROOF
75
0.1 92
WT. OF SOIL 612
50
WT. OF BASE SLAB 525 0.5 276
25
NET MOMENT DUE TO SOIL 3
T 2
892
OTAL 528

DISTANCE OF POINT OF CROSSING OF

RESULTANT
WITH BASE FROM EDGE OF HEEL SLAB
Z = 0.35 M
ECCENTICITY OF LOADING
E = -0.172 M
MAX. SOIL PRESSURE NEAR EDGE OF TOE
5096.17*(1+6*0.06/1.05)/1.05 MXP = 41.40 KG / SQ.M
1
MIN. SOIL PRESSURE NEAR EDGE OF HEEL
5096.17*(1-6*0.06/1.05)/1.05 MNP = 4773.12 KG / SQ.M
1
DESIGN OF TOE SLAB:

MAX. PRESSURE AT FREE EDGE = 41 KG /

SQ.M
PRESSURE AT WALL EDGE OF TOE = 2745 KG /
SQ.M
MAX. BENDING MOMENT = 169.7 KG-
M
DEDUCT MOMENT DUE TO SELF WEIGHT = 90.00 KG-
M
NET DESIGN MOMENT FOR TOE SLAB = 79.68 KG-
M
COEFFICIENT FOR UNCRACKED SECTION 3.33
MIN. THICKNESS REQUIRED = 4.89 Cm
OVERALL THICKNESS PROVIDED IS OK 20.00 Cm
CHOOSE DIA. OF BARS AS = 8.00 MM
CLEAR COVER TO BE PROVIDED = 50 MM
EFFECTIVE DEPTH AVAILABLE = 14.60 CM
AREA OF STEEL REQUIRED = 0.49 SQ.C
M
253.67/ (13.00*14.50*0.86)
SPACING OF BARS REQUIRED = 102.92 CM
C/C
PROVIDED 8.00 MM VERTICAL BARS 20.00 CM
EXTENDED.FROM INNER FACE C/C
+ 8 OF WALL @
DESIGN OF HEEL SLAB:
cover = 50
UPWARD SOIL PRESSURE = 722.18 KG
MOMENT DUE TO UPWARD PRESSURE = 143.81 KG-
M
DOWNWARD SOIL PRESSURE = 612.00 KG
DOWNWARD PRESSURE DUE TO SELF WEIGHT = 150.00 KG
MOMENT DUE TO DOWNWARD PRESSURE = 114.30 KG-
M
NET DESIGN MOMENT = -29.51 KG-
M
coefficient for uncracks section = 3.33
DEPTH OF SECTION REQUIRED FOR UNCRACKED = 2.98 CM
DIA OF BAR CHOSEN F0R TOP FACE = 8.00 MM
EFFECTIVE DEPTH AVIALABLE = 14.60 CM
AREA STEEL REQUIRED = 0.18 SQ
CM
DIA OF BAR CHOSEN F0R LOWER FACE = 8.00 MM
PERCENTAGE TEMPERATURE STEEL REQUIRED = 0.24 %
AREA OF TEMP. STEEL REQD. = 4.80 SQ
CM
MIN AREA OF STEEL REQD. NEAR TOP FACE = 2.40 SQ
CM
SPACING OF BARS REQD.NEAR TOP FACE = 20.93 CM
C\C
SPACING OF BARS PROVIDED = 20.00 CM
C\C
Total AREA OF CIRCUM.TEMP. STEEL REQUIRED = 2.40 SQ
ON EACH FACE CM
DIA OF BARS = 8.00 MM
SPACING OF BARS ON EACH FACE = 20.0 CM
C\C
DESIGN OF INTERNAL COLUMN
The Diameter of Clear water reservoir (CWR) is less than 5.0 m so internal column is not required.