QSFP28 Series
EOLQ-161HG-40-L7 Series
Single-Mode 100GBASE 40km QSFP28 Transceiver
RoHS Compliant
Features
Supports 103Gbps
Single 3.3V Power Supply
Power dissipation < 5W
Up to 40km over SMF
Commercial case temperature range of
0°C to 70°C
Four 25Gbps EML LAN-WDM lasers on
transmitter side
Applications
APD and TIA array on the receiver side
100G 40km applications
4x25G electrical interface
with FEC on host side
Duplex LC receptacles
100G Datacom&Telecom
I2C interface with integrated Digital Diagnostic
connections
Monitoring
Safety Certification: TUV/UL/FDA*Note1
RoHS Compliant
Ordering Information
Data Distance
Part No. Fiber Interface Temp. DDMI
Rate *(note3)
EOLQ-161HG-40-L7*(note2) 103Gbps SMF 40km LC 0℃~+70℃ Yes
Note1: For the latest certification information, please check with Eoptolink.
Note2: Standard version
Note3: Over SMF
*The product image only for reference purpose.
Eoptolink Technology Inc., Ltd.
Page 1 of 7 V1.d
QSFP28 Series
Product Description
Eoptolink’s EOLQ-161HG-40-L7 QSFP28 transceiver module is designed for 100 Gigabit
Ethernet links over 40Km single mode fiber. Digital diagnostics functions are available via an I2C
interface, as specified by the QSFP+ MSA. And compliant with 100G 4WDM-40 MSA.
Absolute Maximum Ratings
Parameter Symbol Min. Max. Unit
Storage Temperature Ts -40 +85 °C
Supply Voltage Vcc -0.5 3.6 V
Operating Relative Humidity RH 5 85 %
*Exceeding any one of these values may destroy the device immediately.
Recommended Operating Conditions
Parameter Symbol Min Typical Max Unit
Operating Case Temperature Tc 0 70 °C
Power Supply Voltage Vcc 3.135 3.3 3.465 V
Power Dissipation PD 5 W
Performance Specifications – Electrical
Parameter Symbol Min Typical Max Unit
Transmitter
Differential data input swing per lane 900 mvp-p
Input Impedance (Differential) Zin 10 %
Stressed input parameters
Eye width 0.46 UI
Applied pk-pk sinusoidal jitter IEEE 802.3bm Table 88-13
Eye height 95 mv
DC common mode voltage -350 2850 mv
Receiver
Differential output amplitude 200 900 mvp-p
Output Impedance (Differential) Zout 10 %
Eye width 0.57 UI
Eye height differential 228 mv
Vertical eye closure 5.5 dB
Optical Characteristics
Parameter Symbol Min Typical Max Unit
Transmitter
Signaling Speed per Lane BRAVE 25.78125 Gbps
Data Rate Variation -100 +100 ppm
Lane_0 Center Wavelength λC0 1294.53 1295.56 1296.59 nm
Eoptolink Technology Inc., Ltd.
Page 2 of 7 V1.d
QSFP28 Series
Lane_1 Center Wavelength λC1 1299.02 1300.05 1301.09 nm
Lane_2 Center Wavelength λC2 1303.54 1304.58 1305.63 nm
Lane_3 Center Wavelength λC3 1308.09 1309.14 1310.19 nm
Total Average Output Power Po 12.5 dBm
Average Launch Power per
Peach -2.5 6.5 dBm
Lane*(Note4)
Optical Modulation Amplitude Peach
0.5 6.5 dBm
(OMA), each lane*(Note5) (OMA)
Average launch power of OFF
Poff -30 dBm
transmitter per lane
Side-mode suppression ratio SMSR 30 dB
Transmitter dispersion
TDP 2.0 dB
penalty , each lane*(Note6)
Difference in launch power
4 dB
between any two lanes (OMA)
Optical Return Loss Tolerance 20 dB
Transmitter reflectance*(Note7) -26
Extinction Ratio ER 4.5 dB
Transmitter eye mask {0.25, 0.4,
definition {X1, X2, X3, Y1, Y2, 0.45, 0.25,
Y3}*(Note8) 0.28, 0.4}
Receiver
Signaling Speed per Lane BRAVE 25.78125 Gbps
Data Rate Variation -100 +100 ppm
Receiver overload per Lane Psat -3 dBm
Lane_0 Center Wavelength λC0 1294.53 1295.56 1296.59 nm
Lane_1 Center Wavelength λC1 1299.02 1300.05 1301.09 nm
Lane_2 Center Wavelength λC2 1303.54 1304.58 1305.63 nm
Lane_3 Center Wavelength λC3 1308.09 1309.14 1310.19 nm
Average Receive Power per
Rx_pow -20.5 -3.5 dBm
Lane*(Note9)
Damage threshold per
Pdamage -2.5 dBm
lane(min) *(Note10)
Receive Sensitivity in OMA
Rx_sens -18.5 dBm
per Lane*(Note11)
Stressed Receiver Sensitivity
RXSRS -16 dBm
(OMA) per Lane*(Note12)
Receiver Reflectance ORL -26 dB
LOS Assert LOSA -35 dBm
LOS De-Assert LOSD -25 dBm
LOS Hysteresis 0.5 dB
Eoptolink Technology Inc., Ltd.
Page 3 of 7 V1.d
QSFP28 Series
Note4: Average launch power, each lane (min) is informative and not the principal indicator of signal strength. A
transmitter with launch power below this value cannot be compliant; however, a value above this does not ensure
compliance.
Note5: Even if the TDP < 1.0dB, the OMA (min) must exceed 0.5 dBm.
Note6: Measured at 100Gbps & BER = 5*10-5.
Note7: Transmitter reflectance is defined looking into the transmitter.
Note8: Vertical eye closure penalty, stressed eye J2 Jitter, stressed eye J4 Jitter, and SRS eye mask definition
are test conditions for measuring stressed receiver sensitivity. They are not characteristics of the receiver.
Note9: Average receive power, each lane (min) is informative and not the principal indicator of signal strength. A
received power below this value cannot be compliant; however, a value above this does not ensure compliance.
Note10: The receiver shall be able to tolerate, without damage, continuous exposure to an optical signal having
this average power level.
Note11: Receiver sensitivity (OMA), each lane (max) at 5E-5 BER is a normative specification.
Note12: Measured with conformance test signal at TP3 for BER = 5*10-5.
QSFP28 Transceiver Electrical Pad Layout
Pin Arrangement and Definition
Plug
Pin Logic Symbol Description Notes
Sequence
1 GND Ground 1 1
2 CML-I Tx2n Transmitter Inverted Data Input 3
3 CML-I Tx2p Transmitter Non-Inverted Data Input 3
4 GND Ground 1 1
5 CML-I Tx4n Transmitter Inverted Data Input 3
6 CML-I Tx4p Transmitter Non-Inverted Data Input 3
7 GND Ground 1 1
8 LVTTL-I ModSelL Module Select 3
Eoptolink Technology Inc., Ltd.
Page 4 of 7 V1.d
QSFP28 Series
9 LVTTL-I ResetL Module Reset 3
10 VccRx +3.3V Power Supply Receiver 2 2
11 LVCMOS- I/O SCL 2-wire serial interface clock 3
12 LVCMOS- I/O SDA 2-wire serial interface data 3
13 GND Ground 1 1
14 CML-O Rx3p Receiver Non-Inverted Data Output 3
15 CML-O Rx3n Receiver Inverted Data Output 3
16 GND Ground 1 1
17 CML-O Rx1p Receiver Non-Inverted Data Output 3
18 CML-O Rx1n Receiver Inverted Data Output 3
19 GND Ground 1 1
20 GND Ground 1 1
21 CML-O Rx2n Receiver Inverted Data Output 3
22 CML-O Rx2p Receiver Non-Inverted Data Output 3
23 GND Ground 1 1
24 CML-O Rx4n Receiver Inverted Data Output 3
25 CML-O Rx4p Receiver Non-Inverted Data Output 3
26 GND Ground 1 1
27 LVTTL-O ModPrsL Module Present 3
28 LVTTL-O IntL Interrupt 3
29 VccTx +3.3V Power supply transmitter 2 2
30 Vcc1 +3.3V Power supply 2 2
31 LVTTL-I LPMode Low Power Mode 3
32 GND Ground 1 1
33 CML-I Tx3p Transmitter Non-Inverted Data Input 3
34 CML-I Tx3n Transmitter Inverted Data Input 3
35 GND Ground 1 1
36 CML-I Tx1p Transmitter Non-Inverted Data Input 3
37 CML-I Tx1n Transmitter Inverted Data Input 3
38 GND Ground 1 1
1: GND is the symbol for signal and supply (power) common for the QSFP28 module. All are common
within the QSFP28 module and all module voltages are referenced to this potential unless otherwise
noted. Connect these directly to the host board signal-common ground plane.
2: Vcc Rx, Vcc1 and Vcc Tx are the receiver and transmitter power supplies and shall be applied
concurrently. Vcc Rx Vcc1 and Vcc Tx may be internally connected within the QSFP28 Module in any
combination. The connector pins are each rated for a maximum current of 1000mA.
Eoptolink Technology Inc., Ltd.
Page 5 of 7 V1.d
QSFP28 Series
Mechanical Specifications
*This 2D drawing only for reference, please check with Eoptolink before ordering.
Obtaining Document
You can visit our website: http://www.eoptolink.com
Or contact Eoptolink Technology Inc., Ltd. Listed at the end of the documentation to get the latest
documents.
Revision History
Revision Initiated Reviewed Approved Revision History Release Date
V1.a Eliss Preliminary Jul 13, 2017
Update optical index and
V1.b Torres Kelly/Neal Jul 10, 2018
the regulatory compliance.
Update transmitter optical
Erik/Elaine characteristics and the
V1.c Yvan Nov 8, 2018
/Eliss maximum current of
connector pins.
Torres/Kelly
Update optical
Erik/Tracy/
characteristics & 2D
V1.d Neal Eliss/Angela/ Dec 14, 2018
drawing
Derrick/
Elaine
Eoptolink Technology Inc., Ltd.
Page 6 of 7 V1.d
QSFP28 Series
Notice:
Eoptolink reserves the right to make changes or discontinue any optical link product or service
identified in this publication, without notice, in order to improve design and/or performance.
Applications that are described herein for any of the optical link products are for illustrative
purposes only. Eoptolink makes no representation or warranty that such applications will be
suitable for the specified use without further testing or modification.
Contact:
Add: No.127 West Wulian Street, Gongxing Town, Shuangliu District, Chengdu, 610213, P.R.
CHINA
Tel: (+86) 028-67087999
Fax:(+86) 028-67087979
Postal: 610213
E-mail:[email protected]
http://www.eoptolink.com
Eoptolink Technology Inc., Ltd.
Page 7 of 7 V1.d
