General Industrial Coatings

CC-B7
Fast Production Enamel
Gloss Black.......................... F75BC6 Green ................................... F75GC2 Equipment Yellow .................... G74YC165
Flat Black ............................. F75BC7 Omaha Orange ..................... F75EC2 Federal Yellow ............................. F75YC4
Blue ...................................... F75LC2 Red....................................... F75RC4 Safety Yellow ............................... F75YC3
Blending Clear .................... F75V100 White ................................... F75WC1 Catalyst (optional) ......................... V66V29
ASA 49 Gray ........................ F75AC1 Blending White ................... F75W100 Custom Blend Series ..................... F75XX

DESCRIPTION CHARACTERISTICS SPECIFICATIONS

(may vary by color)
Fast Production Enamel is an alkyd General: All substrates should be free of
enamel intended for finishing or refinishing High Gloss: 85+ mold release, oil, grease, dirt, fingerprints,
industrial, construction and agricultural drawing compounds, surface passivation
equipment. Volume Solids: 27-34 ± 1 % treatments and any other contaminants to
ensure optimum adhesion and coating
Advantages: Viscosity: 22-34 secs., #3 Zahn Cup performance. Consult Metal Preparation
• Fast air dry brochure CC-T1 for additional details.
• Full gloss range available Recommended Film Thickness:
• Good exterior durability, except for red, Mils Wet 3.5-5.0 Aluminum: If untreated, prime with RoHS
yellow, and orange Mils Dry 1.0-1.5 Compliant Wash Primer, P60G10 or
• Good one coat protection Industrial Wash Primer, P60G2. Over pre-
• Good flexibility and film toughness Spreading Rate (no application loss): treated aluminum, check adhesion before
• Full range of custom colors 289-545 ft.2/gal. at 1.0-1.5 mils DFT use as the proprietary pretreatment may
• May be catalyzed for increased hardness change from supplier to supplier which may
and improved chemical resistance Cure: have an effect on the final adhesion.
properties Air Dry or
Force Dry 20 minutes at 140° F Galvanized Steel: If untreated, prime with
• Working potlife after catalyzation is 6-8
RoHS Compliant Wash Primer, P60G10 or
hours at room temperature Substrate Disclaimer: Curing of coating at Industrial Wash Primer, P60G2.
temperatures higher than the heat distortion
Fast Production Enamel Urethane For parameters of the substrate may cause substrate
increased chemical abrasion resistance, issues. Galvanized Iron: If untreated, prime with
improved hardness, sharper gloss, and RoHS Compliant Wash Primer, P60G10,
better color and gloss retention, Fast Drying: 77° F, 45% RH Industrial Wash Primer, P60G2, or Kem
Production Enamel may be catalyzed at an To Touch 10 minutes Aqua® Wash Primer, E61G522.
8:1 ratio with Polane Exterior Catalyst,
® To Handle 30 minutes
V66V29, prior to reduction. Drying times will To Recoat 30 minutes Steel or Iron: Remove rust, mill scale, and
be slower. To Pack 24 hours oxidation products. For best results, treat
the surface with a proprietary surface
Flash Point: 40-45° F chemical treatment of zinc or iron
Pensky Martens Closed Cup phosphate to improve corrosion protection.
For exterior exposure, prime with Kem-
Potlife: 6-8 hours Flash® Prime (E61A45 series).
After catalyzation at room temperature
Wood (interior only): Must be clean, dry,
Recoat Window: If strong solvents such as
and finish sanded. Substrate should be free
xylene or toluene are used, a critical recoat
may occur between 2-18 hours. of any contamination to ensure optimum
adhesion and coating performance
properties.
Package Life: 3 years, unopened
V66V29 24 months, unopened

Air Quality Data:

**Non-photochemically reactive
Testing: The information, data, and
*Volatile Organic Compounds (VOC), Less Exempts recommendations set forth in this Product
As packaged, maximum 4.8 lbs/gal, 576 g/L Data Sheet are based upon test results
Reduced 25% with Xylene 5.3 lbs/gal, 636 g/L believed to be reliable. However, due to the
*VOC Compliance limits vary from state to **Reducing with xylene, toluene, Aromatic wide variety of substrates, substrate
Naphtha, or other aromatic solvents makes
state; please consult local Air Quality rules this product photochemically reactive.
properties, surface preparation methods,
and regulations. equipment and tools, application methods,
and environments, the customer should test
An Environmental Data Sheet is available the complete system for adhesion,
from your local Sherwin-Williams facility or at compatibility, and performance prior to full
www.PaintDocs.Com. scale application.

CC-B7 April/2023 continued on back

 APPLICATION ADDITIONAL INFORMATION CAUTIONS
Typical Setups

May be applied by: Conventional Spray 1. If strong solvents such as xylene or FOR INDUSTRIAL SHOP APPLICATION
Airless Spray toluene are used, a critical recoat may ONLY
occur between 2-18 hours.
Conventional Spray: 2. Blocking or sticking may occur when flat Thoroughly review the product label and
Air Pressure 45-60 psi surfaces are stacked before adequate Safety Data Sheet (SDS) for safety
Fluid Pressure 20-25 psi cure. Allow at least 24 hours before information and cautions prior to using
Reducer R2K4 (Xylene) stacking. this product.
Reduction Rate 20-25% 3. Fast Production Enamel reds, oranges,
R2K5 (Aromatic Naphtha) or R2K1 To obtain the most current version of the
(Toluene) can also be used. and yellows contain bleeding pigments.
Environmental Data Sheet (EDS), Product
Use caution when recoating with
Data Sheet (PDS), or Safety Data Sheet
Airless Spray: products containing aromatic ester or (SDS) please visit your local Sherwin-
Tip 0.013-0.017 in. ketone solvents. Williams facility or www.PaintDocs.Com.
Reducer R2K4 (Xylene) 4. The reds, oranges, and yellows have
Reduction Rate 10% been formulated to give optimum Please direct any questions or comments to
R2K5 (Aromatic Naphtha) can also be durability as packaged. Using these your local Sherwin-Williams facility.
used. colors for intermixing may result in color
walk out or premature fading on
Equipment/application guidelines are only exposure.
guidelines and individual application & 5. Compatible with Opticolor® and GIS
process parameters will dictate exact colorants. Do not add more than 16
requirements. ounces of colorant per gallon of base.

Cleanup: Clean tools/equipment

immediately after use with toluene or xylene.

Follow manufacturer's safety

recommendations when using any solvent.
Note:
All purchases of products from Sherwin-
Williams are exclusively subject to Sherwin-
Williams' Standard Terms And Conditions Of
Sale. Please review these terms and
conditions prior to the purchase of the
products.

Sherwin-Williams warrants the product to be

free of manufacturing defect in accordance
with Sherwin-Williams’ quality control
procedures. Except for the preceding
sentence, due to factors that are outside of
Sherwin-Williams’ control, including
substrate selection, and customer handling,
preparation, and application, Sherwin-
Williams cannot make any other warranties
related to the product or the performance of
the product. SHERWIN-WILLIAMS
DISCLAIMS ALL WARRANTIES OF ANY
KIND, EXPRESS OR IMPLIED,
INCLUDING BUT NOT LIMITED TO THE
IMPLIED WARRANTY OF
MERCHANTABILITY, THE IMPLIED
WARRANTY OF FITNESS FOR A
PARTICULAR PURPOSE.

Liability for products proven to be defectively

manufactured will be limited solely to
replacement of the defective product or the
refund of the purchase price paid for the
defective product, as determined by Sherwin
-Williams. Under no circumstances shall
Sherwin-Williams be liable for indirect,
special, incidental or consequential
All trademarks are the property of their damages, lost profits or punitive damages
respective owners. arising from any cause whatsoever.

CC-B7 Fast Production Enamel